An alternative method for the treatment of waste produced at a dye and a metal-plating industry using natural and/or waste materials.

The aim of this study was to develop cost-effective, appropriate solidification technologies for treating hazardous industrial wastes that are currently disposed of in ways that may threaten the quality of local groundwater. One major objective was to use materials other than cement, and preferably materials that are themselves wastes, as the solidification additives, namely using wastes to treat wastes or locally available natural material. This research examines the cement-based and lime-based stabilization/solidification (S/S) techniques applied for waste generated at a metal-plating industry and a dye industry. For the lime-based S/S process the following binder mixtures were used: cement kiln dust/ lime, bentonite/lime and gypsum/lime. For the cement-based S/S process three binder mixtures were used: cement kiln dust/cement, bentonite/cement and gypsum/cement. The leachability of the wastes was evaluated using the toxicity characteristic leaching procedure. The applicability and optimum weight ratio of the binder mixtures were estimated using the unconfined compressive strength test. The optimum ratio mixtures were mixed with waste samples in different ratios and cured for 28 days in order to find the S/S products with the highest strength and lowest leachability at the same time. The results of this work showed that the cement-and lime-based S/S process, using cement kiln dust and bentonite as additives can be effectively used in order to treat industrial waste.     

Hazardous waste incinerators under waste uncertainty: Balancing and throughput maximization via heat recuperation

Hazardous waste incinerators (HWIs) differ substantially from thermal power facilities, since instead of maximizing energy production with the minimum amount of fuel, they aim at maximizing throughput. Variations in quantity or composition of received waste loads may significantly diminish HWI throughput (the decisive profit factor), from its nominal design value. A novel formulation of combustion balance is presented, based on linear operators, which isolates the wastefeed vector from the invariant combustion stoichiometry kernel. Explicit expressions for the throughput are obtained, in terms of incinerator temperature, fluegas heat recuperation ratio and design parameters, for an arbitrary number of wastes, based on fundamental principles (mass and enthalpy balances). The impact of waste variations, of recuperation ratio and of furnace temperature is explicitly determined. It is shown that in the presence of waste uncertainty, the throughput may be a decreasing or increasing function of incinerator temperature and recuperation ratio, depending on the sign of a dimensionless parameter related only to the uncertain wastes. The dimensionless parameter is proposed as a sharp a’ priori waste ‘fingerprint’, determining the necessary increase or decrease of manipulated variables (recuperation ratio, excess air, auxiliary fuel feed rate, auxiliary air flow) in order to balance the HWI and maximize throughput under uncertainty in received wastes. A 10-step procedure is proposed for direct application subject to process capacity constraints. The results may be useful for efficient HWI operation and for preparing hazardous waste blends.     

Improvement of permeability of waste sludge by mixing with slag or construction and demolition waste

To determine the allowable ratio of waste sludge required to ensure an aerobic zone in the landfill, we investigated sludge permeability, which involved mixing sludge, the major landfill waste in Japan, at different mixing ratios with other wastes (slag and construction and demolition waste (C&D)). We measured parameters of sample permeability and analyzed parameters that exert a large influence on oxygen penetration depth with a simulation model accounting for both diffusion and convection driven by temperature gradients. We also determined the critical volumetric contents in which gas and/or water permeability change significantly when sludge is mixed with sand or gravel. From the results of the simulations, gas permeability of the layer, the difference between inside and outside temperatures and the oxygen consumption rate exert a large influence on the resulting oxygen penetration depth. The allowable ratio of sludge required to ensure an aerobic zone in the landfill was determined by considering the balance of the above three parameters. By keeping volumetric sludge content to below 25%, air convection and oxygen penetration depth of several meters were achieved in the modeling.     

Carbon dioxide and ammonia emissions during composting of mixed paper, yard waste and food waste

The objective of the work was to provide a method to predict CO2 and NH3 yields during composting of the biodegradable fraction of municipal solid wastes (MSW). The compostable portion of MSW was simulated using three principal biodegradable components, namely mixed paper wastes, yard wastes and food wastes. Twelve laboratory runs were carried out at thermophilic temperatures based on the principles of mixture experimental and full factorial designs. Seeded mixed paper (MXP), seeded yard waste (YW) and seeded food waste (FW), each composted individually, produced 150, 220 and 370 g CO2-C, and 2.0, 4.4 and 34 g NH3-N per dry kg of initial substrate, respectively. Several experimental runs were also carried out with different mixtures of these three substrates. The effect of seeding was insignificant during composting of food wastes and yard wastes, while seeding was necessary for composting of mixed paper. Polynomial equations were developed to predict CO2 and NH3 (in amounts of mass per dry kg of MSW) from mixtures of MSW. No interactions among components were found to be significant when predicting CO2 yields, while the interaction of food wastes and mixed paper was found to be significant when predicting NH3 yields.     

Transesterification of waste vegetable oil under pulse sonication using ethanol,methanol and ethanol–methanol mixtures

This study reports on the effects of direct pulse sonication and the type of alcohol (methanol and ethanol) on the transesterification reaction of waste vegetable oil without any external heating or mechanical mixing. Biodiesel yields and optimum process conditions for the transesterification reaction involving ethanol, methanol, and ethanol–methanol mixtures were evaluated. The effects of ultrasonic power densities (by varying sample volumes), power output rates (in W), and ultrasonic intensities (by varying the reactor size) were studied for transesterification reaction with ethanol, methanol and ethanol–methanol (50%-50%) mixtures. The optimum process conditions for ethanol or methanol based transesterification reaction of waste vegetable oil were determined as: 9:1 alcohol to oil ratio, 1% wt. catalyst amount, 1–2 min reaction time at a power output rate between 75 and 150 W. It was shown that the transesterification reactions using ethanol–methanol mixtures resulted in biodiesel yields as high as >99% at lower power density and ultrasound intensity when compared to ethanol or methanol based transesterification reactions.     

Reaction Kinetic Model For Optimal Pyrolysis Of Plastic Waste Mixtures

Reaction kinetics at various temperatures for pyrolysis of mixtures of plastic waste [polyethylene(PE) and polystyrene(PS)] are modelled in terms of five types of pyrolysis reaction. The model development is based on the assumption that as plastic wastes are heated in a non-reactive environment they are decomposed homogeneously to various products of gas, oil and char by a first-order rate, irreversible reaction and isothermal condition. Among the five models, the type II model in which the activated polymer exists as an intermediate product is the most accurate in predicting the pyrolysis products of pure PE or pure PS. Also, for mixtures of plastics both type II and IV models can be used to explain the composition of pyrolysis products. Furthermore, from the analysis of variance (ANOVA), the mixing ratio and temperature are shown to be the parameters that have the greatest effect on the pyrolysis reaction of polymer waste mixture. The pyrolysis reaction time for the maximum oil production from PE-PS mixtures is shorter than for PE alone and approaches that of PS alone. Oil production increases with increase of PS content. The optimal temperature for maximum oil production is 600°C for the pyrolysis of 2:8, 5:5 and 1:0 mixtures (w/w) of PE and PS. Oil production for PS alone is constant when the pyrolysis is above 600°C.     

Solid waste characterization and recycling potential for a university campus

Integrated waste management systems are one of the greatest challenges for sustainable development. For these systems to be successful, the first step is to carry out waste characterization studies. In this paper are reported the results of a waste characterization study performed in the Campus Mexicali I of the Autonomous University of Baja California (UABC). The aim of this study was to set the basis for implementation of a recovery, reduction and recycling waste management program at the campus. It was found that the campus Mexicali I produces 1ton of solid wastes per day; more than 65% of these wastes are recyclable or potentially recyclable. These results showed that a program for segregation and recycling is feasible on a University Campus. The study also showed that the local market for recyclable waste, under present conditions - number of recycling companies and amounts of recyclables accepted - can absorb all of these wastes. Some alternatives for the potentially recyclables wastes are discussed. Finally some strategies that could be used to reduce waste at the source are discussed as well.     

A study of the dental solid waste produced in a school of dentistry in Turkey

Dental wastes are regulated under medical waste control regulations in most countries. Even though the quantity of hazardous wastes in dental solid wastes is a small proportion, there is still cross infection risk and potential danger for environment associated with mismanaged wastes. For this reason, knowledge of waste composition and development of proper management alternatives are necessary. In this study, the composition of solid wastes coming from eight clinics of the dental school of a University hospital in Turkey is examined. Although the waste has some variations between the two samplings, the general picture is such that the major components remain pretty much the same (in terms of %) for a fixed clinic. The composition of waste changes from one clinic to the other as expected. However, one can deduce from the data obtained that at about 35%, rubber gloves constitute close to the half of the total solid waste in almost all the clinics. Other major component is paper forming approximately 30% of the solid waste. In general, total waste coming from the clinics is related with the number of procedures conducted on patients at the clinics. Only a small fraction of the waste is hazardous indicating that at Hacettepe University School of Dentistry, hazardous waste collection rules are obeyed in most of the times.     

Use of mix of clay/solid waste from steel works for civil construction materials.

The present study focuses on the use of solid waste generated by the steel works in Brazil for manufacturing clay-based structural products. The waste sample was characterized regarding chemical composition, X-ray diffraction, particle size, morphology, specific surface and plastic properties. The waste was added in gradual proportions to a kaolinitic clay from zero up to 3 wt.%. Ceramic bodies were formed by vacuum extrusion and fired at 950 degrees C. The physical-mechanical properties (linear shrinkage, water absorption, apparent density and flexural strength) of the resulting clay/solid waste mixtures were determined. In addition, leaching tests were performed according Brazilian Standards as well as a preliminary analysis of gases evolved during the thermal process. It was found that the solid waste is formed by irregular particles, ranging in size from 1 to 500 microm. The test results indicate that solid wastes generated by steel works can be used as filler in construction materials, thereby increasing reuse in an environmentally safe manner.     

Controlled combustion tests and bottom ash analysis using household waste with varying composition

The influence of the co-combustion of household waste with either sewage sludge, shredder fluff, electronic and electrical waste (WEEE) or PVC on the bottom ash quality and content was investigated under controlled laboratory conditions using a pot furnace. This laboratory approach avoids the interpretation problems related to large variations in input waste composition and combustion conditions that are observed in large scale MSW incinerators. The data for metals content, transfer coefficients and leaching values are presented relative to data for a base household waste composition that did not contain any of the added special wastes. The small WEEE invited direct measurement of precious metals content in the ashes, where measurement accuracy is facilitated by using only mobile phone scrap for small WEEE. The analyses were carried out for different particle size ranges that are of relevance to the recyclability of metals and minerals in the ashes. Positive correlations were found between elements content of the input waste and the bottom ashes, and also between increased levels of Cl, Mo and Cu in the input waste and their leaching in the bottom ashes. These correlations indicate that addition of PVC, small WEEE and shredder fluff in input waste can have a negative influence on the quality of the bottom ashes. Enrichment of Au and Ag occurred in the fractions between 0.15 and 6 mm. The precious metals content represents an economically interesting intrinsic value, even when the observed peak values are properly averaged over a larger volume of ashes. Overall, it has been shown that changes in quality and content of bottom ashes may be traced back to the varied input waste composition.     

Healthcare waste management in the capital city of Mongolia

Inconsistencies are present in the management options for healthcare wastes in Mongolia. One of the first critical steps in the process of developing a reliable waste management plan requires the performance of a waste characterization analysis. The objectives of this study were an assessment of the current situation of healthcare waste management (HCWM) and characterization of healthcare wastes generated in Ulaanbaatar. A total about 2.65 tonnes of healthcare wastes are produced each day in Ulaanbaatar (0.78 tons of medical wastes and 1.87 tons of general wastes). The medical waste generation rate per kg/patient-day in the inpatient services of public healthcare facilities was 1.4-3.0 times higher than in the outpatient services (P<0.01). The waste generation rate in the healthcare facilities of Ulaanbaatar was lower than in some other countries; however, the percentage of medical wastes in the total waste stream was comparatively high, ranging from 12.5% to 69.3%, which indicated poor waste handling practices. Despite the efforts for the management of wastes, the current system of healthcare waste management in Ulaanbaatar city of Mongolia is under development and is in dire need of immediate attention and improvement. It is essential to develop a national policy and implement a comprehensive action plan for HCWM providing environmentally sound technological measures to improve HCWM in Mongolia.     

Scenario of solid waste reuse in Khulna city of Bangladesh

The reuse and recycling of waste materials are now sincerely considered to be an integral part of solid waste management in many parts of the world. In this context, a vast number of options ranging from small scale decentralized to larger scale centralized plants have been adopted. This study aimed at investigating the waste reuse schemes in Khulna city located in the southern part of Bangladesh and ranked third largest city in the country. The shops for reusable material (SRM) were mostly situated around railway, waterway, and truck station markets which provided easy transportation to further locations. For the reuses of waste materials and products, a chain system was found to collect reusable wastes under a total number of 310 identified SRM with 859 persons directly or indirectly involved in the scheme. This was a decentralized waste management system with self sufficient (autonomous) management. According to mass balance, about 38.52 tons d^?1 solid wastes were reused in Khulna city area, accounting for 7.65% of the total generated wastes. This study revealed that apparently a silent, systematic, smooth, and clean reuse chain has been established in Khulna city area under private initiatives, whose sustainability was confirmed over the years in the country without any official or formal funds. However, proper adjustment between the higher and lower chain in the materials flow path, as well as personal hygiene training for the workers, would further improve the achievements of the established reuse scheme.     

Integrated waste management--looking beyond the solid waste horizon

Waste as a management issue has been evident for over four millennia. Disposal of waste to the biosphere has given way to thinking about, and trying to implement, an integrated waste management approach. In 1996 the United Nations Environmental Programme (UNEP) defined 'integrated waste management' as 'a framework of reference for designing and implementing new waste management systems and for analysing and optimising existing systems'. In this paper the concept of integrated waste management as defined by UNEP is considered, along with the parameters that constitute integrated waste management. The examples used are put into four categories: (1) integration within a single medium (solid, aqueous or atmospheric wastes) by considering alternative waste management options, (2) multi-media integration (solid, aqueous, atmospheric and energy wastes) by considering waste management options that can be applied to more than one medium, (3) tools (regulatory, economic, voluntary and informational) and (4) agents (governmental bodies (local and national), businesses and the community). This evaluation allows guidelines for enhancing success: (1) as experience increases, it is possible to deal with a greater complexity; and (2) integrated waste management requires a holistic approach, which encompasses a life cycle understanding of products and services. This in turn requires different specialisms to be involved in the instigation and analysis of an integrated waste management system. Taken together these advance the path to sustainability.     

Forest products decomposition in municipal solid waste landfills

Cellulose and hemicellulose are present in paper and wood products and are the dominant biodegradable polymers in municipal waste. While their conversion to methane in landfills is well documented, there is little information on the rate and extent of decomposition of individual waste components, particularly under field conditions. Such information is important for the landfill carbon balance as methane is a greenhouse gas that may be recovered and converted to a CO(2)-neutral source of energy, while non-degraded cellulose and hemicellulose are sequestered. This paper presents a critical review of research on the decomposition of cellulosic wastes in landfills and identifies additional work that is needed to quantify the ultimate extent of decomposition of individual waste components. Cellulose to lignin ratios as low as 0.01-0.02 have been measured for well decomposed refuse, with corresponding lignin concentrations of over 80% due to the depletion of cellulose and resulting enrichment of lignin. Only a few studies have even tried to address the decomposition of specific waste components at field-scale. Long-term controlled field experiments with supporting laboratory work will be required to measure the ultimate extent of decomposition of individual waste components.     

金属冶炼进口物料的固体废物鉴别方法

建立了金属冶炼进口物料的固体废物鉴别方法,并利用该方法对海关查扣的3种金属冶炼进口物料进行了固体废物鉴别。鉴别结果显示:物料1、2和3的自然属性分别为砷含量超标铜精矿、锰阳极泥、回转窑氧化锌,产生来源分别为有害物质超标的产品、污染控制设施产生的物质、有意识加工的目标产物;物料1和2属于我国禁止进口的固体废物,物料3不属于固体废物。本文建立的固体废物鉴别方法可行,可为金属冶炼进口物料的固体废物鉴别和监管提供参考。     

An investigation on the use of shredded waste PET bottles as aggregate in lightweight concrete

In this work, the utilization of shredded waste Poly-ethylene Terephthalate (PET) bottle granules as a lightweight aggregate in mortar was investigated. Investigation was carried out on two groups of mortar samples, one made with only PET aggregates and, second made with PET and sand aggregates together. Additionally, blast-furnace slag was also used as the replacement of cement on mass basis at the replacement ratio of 50% to reduce the amount of cement used and provide savings. The water–binder (w/b) ratio and PET–binder (PET/b) ratio used in the mixtures were 0.45 and 0.50, respectively. The size of shredded PET granules used in the preparation of mortar mixtures were between 0 and 4 mm. The results of the laboratory study and testing carried out showed that mortar containing only PET aggregate, mortar containing PET and sand aggregate, and mortars modified with slag as cement replacement can be drop into structural lightweight concrete category in terms of unit weight and strength properties. Therefore, it was concluded that there is a potential for the use of shredded waste PET granules as aggregate in the production of structural lightweight concrete. The use of shredded waste PET granules due to its low unit weight reduces the unit weight of concrete which results in a reduction in the death weight of a structural concrete member of a building. Reduction in the death weight of a building will help to reduce the seismic risk of the building since the earthquake forces linearly dependant on the dead-weight. Furthermore, it was also concluded that the use of industrial wastes such as PET granules and blast-furnace slag in concrete provides some advantages, i.e., reduction in the use of natural resources, disposal of wastes, prevention of environmental pollution, and energy saving.     

Upgrading mixed polyolefin waste with magnetic density separation

Polyolefin fractions are often end fractions resulting from the recycling of end-of-life consumer products. Polypropylene (PP) and polyethylene (PE) are present in such fractions as a mixture. For instance, the ratio of PP and PE in car scrap is 70:30 on average. However, the grade of the PP and PE should typically be better than 97% to be reused again as a high quality product. Density separation of the different polyolefins can be a solution. A promising separation technique is the inverse magnetic density separator (IMDS). This paper discusses the potential of shredder residue, one of the possible polyolefin’s waste stream sources for the IMDS, in detail. Experiments with the separation of polyolefins with an IMDS prototype show both high grade and high recovery. The paper concludes with the economic opportunities of the IMDS in the recycling of polyolefins.     

Development of waste gasification and gas reforming system for municipal solid waste (MSW)

To achieve both high-efficiency power generation and high detoxification performance, advanced-type waste power generation plants such as pyrolysis and gas reforming plants are suggested. Further surveys on actual operational data of these plants are required in terms of reliability of the system when it is introduced to waste disposal sites. To verify the technical effectiveness of advanced-type waste power generation using the pyrolysis and gas reforming method, we evaluated 10?tons/day of municipal solid wastes (MSW) treated in a demonstration plant. A demonstration test was conducted over 100?days including 35?consecutive days of operation treating MSWs. The test results show high recycling performance and harmless nature of the plant which proves it to be an excellent waste recycling system. Major test results are as follows: (1) stabilization of waste treatment is possible with the wastes of various qualities, (2) clean gas is produced from the waste whose energy recovery ratio is approximately 40?%. (3) 99.3?% weight % of dried waste are recovered as valuable materials such as clean gas, char and metal, (4) total amount of dioxin emission to the outside of the plant is very small, down to 0.0051–0.018?μg?TEQ per ton waste.     

Enzymatic hydrolysis of organic waste materials in a solid-liquid system

In the current climate of increasing emphasis on environmental protection and efficient waste management, regional management bodies and environmental agencies are striving to achieve an economical and environmentally acceptable system for the recycling of biodegradable organic wastes. Composting would appear to be a cost effective solution to this problem, but in its entirety, composting is an inherently lengthy and variable process and is restrictive in terms of the demand on resources and space in composting plants. The aim of this study was to compare a biological composting process of solid residues with an enzymatic hydrolysis process of residues. The length of time required to naturally compost three organic materials, spent mushroom compost (SMC), farmyard manure (FYM) and dairy wastewater sludge (DWS) under optimal conditions was 42 days, 98 days and 84 days, respectively. In an attempt to accelerate this process, commercial enzymes were added to the waste products in a heterogeneous solid-liquid system. The enzymes utilised included a range of proteases, cellulases, ligninases, lipases and pectinases, which are responsible for the hydrolysis of protein, cellulose, lignin, lipids and carbohydrates, respectively. Preliminary results indicate that all of the organic materials were stabilised within 9h and that the enzymes used would, therefore, improve the efficiency of a waste management plant, if such a system were employed. Spent mushroom compost has a mean N/P/K ratio of 20:10:10 recorded for composted SMC, while a similar ratio of 20:10:20 was obtained for hydrolysed SMC. In contrast, composted farmyard manure has a N/P/K ratio of 30:0:30 and a ratio of 10:1:10 for hydrolysed FYM. Finally, composted DWS has a N/P/K ratio of 20:1:30 while DWS hydrolysate has a N/P/K ratio of 40:1:20, with the decrease in nitrogen in the composted DWS attributed to the addition of wood chippings and sawdust as a bulking agent. While all three materials have a considerable supply of plant nutrients, the variability in nutrients could be overlooked when employed as a soil amendment.     

Effect of Thermo-Mechanical Degradation of Polypropylene on Hygroscopic Characteristics of Wood Flour-Polypropylene Composites

In this research, the influence of thermo-mechanical degradation of polypropylene (PP) on water absorption and thickness swelling of beech wood flour–PP composites were studied. For this purpose, a virgin PP was thermo-mechanically degraded by two times extrusion under controlled conditions. The results showed that the melt flow index, water absorption and thickness swelling of PP significantly increase by extrusion and re-extrusion. The virgin PP and degraded polypropylene were compounded with wood flour (at 60% by weight wood flour loading) in a counter-rotating twin-screw extruder in presence or absence of MAPP to produce wood flour–PP composites. From the results, the composites containing recycled PP exhibited higher water absorption and thickness swelling. The use of MAPP decreased water absorption and thickness swelling in composites made of virgin or recycled PP.