新型复合菌种降解餐厨垃圾

餐厨垃圾占我国目前的城市垃圾结构的比例为30%~50%,采用微生物技术是实现餐厨垃圾减量化,资源化和无害化的有效方法。本研究引进日本东北大学选育的复合菌种,利用菌种将餐厨垃圾发酵分解成有机肥料,探究复合菌种降解效果及产出物的可用性,并对中试微生物处理机操作条件进行优化。结果表明,复合菌种处理餐厨垃圾减量率85%以上,升温快速,高温维持时间较长,腐熟时间较短,腐熟彻底。Fluent软件模拟结果显示:中试采用七叶桨搅拌器优于五叶桨,搅拌转速为6 r·min-1时,经济性和混合效果均较佳。     

餐厨垃圾厌氧发酵特性的研究

为了实现餐厨垃圾低成本现场能源化处理，利用单相法，采用正交试验法，研究了接种率、温度和含水率对餐厨垃圾厌氧发酵过程中运行特性的影响。结果表明，接种率、含水率、发酵温度以及它们之间的交互作用对餐厨垃圾产气效果影响显著，其中以接种率与温度的交互作用影响最为显著，其次是含水率。采用单相法进行55℃高温厌氧发酵，保证65%左右的接种率和90%以上的含水率，完全可以实现餐厨垃圾现场处理。     

餐厨垃圾连续堆肥处理系统中试研究

餐厨垃圾是影响城市环境重要的污染源,其处理尤其是就地堆肥处理近年来受到重视.为了利用园林绿化基质作为餐厨垃圾堆肥的水分调节材料,按照1:1体积比进行连续堆肥,研究添加园林绿化基质对餐厨垃圾堆肥过程中理化指标的影响,为餐厨垃圾无害化处理提供科学依据和技术指导.结果表明,物料堆肥升温启动迅速,第3天就达到50℃,高温持续10 d以上,达到无害化要求；堆肥最终减容率达到53％以上,减量化效果明显；物料总氮和总磷含量呈升高趋势,总有机质含量降低,肥料营养元素含量在6％以上,符合有机肥国家标准(NY525-2002).总的来说,园林绿化基质作为调理剂与餐厨垃圾联合堆肥方法可行,减量化效果好,品质符合标准.     

餐厨垃圾和绿化废弃物换向通风好氧堆肥

以某高校餐厨垃圾和绿化废弃物为原料,利用一种换向通风的堆肥降解装置对其进行好氧堆肥处理,研究了2个进气温度(35℃、45℃)和3个通风速率(1.5、2.5和4 m3/h)6个处理组对堆肥原料理化性质(堆体温度、含水率、pH值、有机质含量、C/N、种子发芽指数)的影响。餐厨垃圾和绿化废弃物进行15 d好氧堆肥后,pH值上升到7左右,有机质含量达到20%~80%,C/N都降到20以下,种子发芽指数均大于50%。经过1个月腐熟,其含水率≤30%。上述指标符合有机肥料标准(NY525-2011)的要求,该堆肥产物可用于园林绿地,具有显著的经济效益和生态效益。本研究结果表明,将城市餐厨垃圾和绿化废弃物混合后进行好氧堆肥是废弃物处理的高效工程,具有良好的发展前景。     

餐厨垃圾混菌发酵制备燃料乙醇

以校园餐厨垃圾为原料,利用根霉和枯草芽胞杆菌进行糖化预处理,再接种啤酒酵母发酵产乙醇。通过单因素实验,以乙醇产量为响应值,对发酵条件进行优化。实验结果表明:乙醇产量最佳的发酵条件为:当底料含水率为22.79%,啤酒酵母接种量为15%,30℃培养条件下,经过5 d发酵,乙醇产量最高可达到6.67%。选用餐厨垃圾丰富了燃料乙醇的取材途径,实现了原材料的多元化,采用微生物预降解原材料为实现高产乙醇奠定了基础。     

微生物菌剂强化餐厨垃圾和污泥联合堆肥

为探究微生物菌剂对餐厨垃圾和污泥联合好氧堆肥的影响,以餐厨垃圾和污泥(湿重1∶1)混合原料为堆肥底物,添加底物总湿重30％的废木屑作为膨胀剂,向底物中分别加入微生物菌剂和腐熟堆肥为处理组,并以不添加外源物作为对照,通过测定堆肥过程中的理化性质、腐熟效果和营养元素的变化,考察菌剂和腐熟堆肥对联合堆肥的促进作用.结果表明,...     

超高温菌好氧堆肥技术对餐余垃圾中油脂、盐分的处理效果研究

餐余垃圾高油高盐特征是影响其堆肥化效果的重要因素。从超高温环境下培养出以芽孢杆菌属(Bacillus)为核心的超高温菌群,考察超高温菌群对餐余垃圾好氧堆肥化过程中堆体温度、物料含水率、pH、种子发芽指数等的影响,并分析好氧堆肥化过程中微生物种群的变化。结果表明,添加超高温菌群后,餐余垃圾好氧堆肥化温度最高可达83℃,75℃以上温度可以维持6 d,含水率由50.23%下降至26.71%,油脂、盐分质量分数分别从1.94%、3.62%降低至0.15%、0.88%,降解率较未添加超高温菌群的对照组分别提升了15.30百分点、17.29百分点。芽孢杆菌属和芽孢八叠球菌属(Sporosarcina)是维持超高温的重要菌属,堆肥芽孢杆菌属(Compostibacillus)和芽孢八叠球菌属是提高油脂、盐分降解效率的重要菌属。超高温菌好氧堆肥化技术处理餐余垃圾相较于传统好氧堆肥化技术能有效提高餐余垃圾中油脂、盐分的降解效率,在一定程度上促进了相关菌种的生长,提高堆体腐熟程度。     

基于响应面法的新型餐厨垃圾菌剂制备

设计三因素三水平实验并采用响应面优化法对反应适宜的实验参数进行了优化.选择温度、供氧条件和反应时间作为菌剂制备的可控因素,选择温度、菌剂投加量和木屑投加量(水分调节)作为菌剂处理厨余垃圾的可控因素,研究菌剂制备与处理垃圾的优化工艺参数.研究结果表明,菌剂的最优制备条件为:温度35℃、间歇震荡、培养108 h,按重量百分比为碎花生壳∶刨花∶鱼骨粉∶麸皮∶菌体=2∶1∶1∶1∶1比例制得的固体菌剂具有较高的活性.菌剂处理厨余垃圾的响应面优化法分析结果表明,当温度为45℃,菌剂投加量为6％,木屑投加量为30％时,厨余垃圾的减量率最大,2d降解率可达40％.     

利用污泥熟肥作为高含水率污泥堆肥调理剂

采用静态强制通风好氧堆肥的方法,以木屑作为对比,考察了利用污泥熟肥作为调理剂对污泥堆肥过程的影响。结果表明,与以木屑作为调理剂的污泥堆体(对照组)相比,以污泥熟肥作为调理剂的污泥堆体(实验组)升温快,高温阶段(>50℃)持续时间长达10 d,满足粪便无害化卫生标准的要求,而对照组仅持续了2 d;实验组腐熟的堆肥含水率从60%降到39%,下降了21%,pH维持在7.5～8.5范围内,微生物活性较强,而对照组含水率仅下降15%,pH始终低于7.5;实验组种子发芽指数(GI)在第14天就回升到80%以上,基本上去除了植物毒性,而对照组GI在第22天才回升到50%。总体而言,污泥熟肥能显著改善堆肥中微生物的微环境,促进有机物的降解,缩短堆肥腐熟时间,是一种优质的调理剂。     

响应面法优化黄粉虫幼虫处理餐厨垃圾饲养条件的研究

研究了黄粉虫幼虫处理餐厨垃圾的方法.首先在饲养温度、饲料含水量和饲养密度等条件下进行单因素实验,然后,以利用率为指标,运用响应面法优化了黄粉虫幼虫处理餐厨垃圾的饲养条件,结果表明,最佳饲养条件为饲养温度26.7℃、饲料含水量14.5％、饲养密度4.1头/cm2.在此饲养条件下,黄粉虫对餐厨垃圾利用率理论值为38.72％,实际餐厨垃圾利用率为38.88％,相对误差为0.41％,说明利用黄粉虫幼虫处理餐厨垃圾具有较好的效果.     

餐厨垃圾中典型组分的裂解液化特征研究

利用实验室规模的实验装置管式加热炉进行餐厨垃圾热解实验,实验分析了反应温度对餐厨垃圾热解产物分布的影响,米饭、白菜、猪肉、塑料和纸5种原料在最佳温度下可实现热解油质量产率的最大化,分别为45.02%、24.55%、61.19%、73.77%和24.86%。其中,米饭和白菜热解油含水率较高,可达到30%~40%,将含水率降到15%后,测定热值分别为25.51 MJ/kg和17.75 MJ/kg。塑料和纸混合热解时,塑料热解过程的放热效应可缩小纸的热解温度区间,增加热解油产量。红外光谱分析厨余热解油包含多种含氧有机物。通过气质联用仪(GC-MS)分析塑料热解油和塑料与纸混合热解油在180℃以下蒸馏出的液相产物,主要组分为烷烃和烯烃,从成分和热值分析,与汽油、柴油相近。     

Effect of bulking agents on maturity and gaseous emissions during kitchen waste composting

This study investigated the effect of bulking agents on the maturity and gaseous emissions of composting kitchen waste. Three different bulking agents (cornstalks, sawdust, and spent mushroom substrate) were used to compost kitchen waste under aerobic conditions in 60-L reactors for a 28-d period. A control treatment was also studied using kitchen waste without a bulking agent. During the experiment, maturity indexes such as temperature, pH value, C/N ratio, and germination index were determined, and continuous measurements of leachate and gaseous emissions (CH₄, N₂O, and NH₃) were taken. The results showed that all of the composts with bulking agents reached the required maturity standard, and the addition of spent mushroom substrate gave the highest maturity (C/N ratio decreased from 23 to 16 and germination index increased from 53% to 111%). The bulking agents also reduced leachate production and CH₄ and N₂O emissions, but had little impact on NH₃ emissions. Composting with sawdust as a bulking agent was found to emit less total greenhouse gas (33 kg CO₂-eq t⁻¹ dry matter) than the other treatments.     

Effects of operating parameters on in situ NH3 emission control during kitchen waste composting and correlation analysis of the related microbial communities

Ammonia emission during composting results in anthropogenic odor nuisance and reduces the agronomic value of the compost due to the loss of nitrogen. Adjusting the operating parameters during composting is an emerging in situ odor control technique that is cheap and highly efficient. The effects of in situ NH₃ emission control were investigated in this study by simultaneously adjusting key operating parameters (such as C/N ratio, aeration rate, and moisture content) during the composting processes (C1–C9). Results showed that the average NH₃ emission concentrations for different treatments were in the order of C1 > C4 > C2 > C5 > C3 > C6 > C7 > C8 > C9. The total content of NH₃ emission (21.02 g/kg) in C9 (C/N ratio = 35, aeration rate = 15 L/min, and moisture content = 60%) was much lower than that (65.95 g/kg) in C1 (C/N ratio = 15, aeration rate = 5 L/min, and moisture content = 60%). The nitrogen loss ratio was 27.36% for C1, while 16.15% for C9. The microbial diversity and abundance in C9 and C1 were compared using high-throughput sequencing. The relationship between NH₃ emission, operating parameters, and the related functional microbial communities was also investigated. Results revealed that Nitrosospira, Nitrosomonas, Nitrobacter, Pseudomonas, Methanosaeta, Rhodobacter, Paracoccus, and Sphingobacterium were negatively related to NH₃ emission. According to the above results, the optimal values for different operating parameters for the in situ NH₃ control during kitchen waste composting were, respectively, moisture content of 70%, C/N ratio of 35, and aeration rate of 15 L/min, with the order of effectiveness from high to low being aeration rate > C/N > moisture. This information could be used as a valuable reference for the in situ NH₃ emission control during kitchen waste composting.

     

基于活性污泥的厨余垃圾厌氧发酵产酸研究

以厨余垃圾和活性污泥为原料,考察了不同接种比例对厌氧发酵产物的挥发性脂肪酸产量、pH值和COD去除率的影响.结果表明,当厨余垃圾和活性污泥接种比例为4∶1时,挥发性脂肪酸产量在第3天达到最大值为42.7 g/L,产率提高了40%,COD去除率达到了35.6%,pH值没有发生较大的差异,其变化幅度在4～6之间.     

Effects of bacterial inoculum and moisture adjustment on composting of pig manure

Spent litter (a mixture of partially composted pig manure and sawdust) was taken from pig pens employing the pig-on-litter system with and without the addition of a commercial bacterial product (Odor control (OC)-organic fertilizers (OF)). A duplicate series of windrows was set up with spent litter which contained the bacterial product and a further duplicate series was set up with spent litter which did not contain the bacterial product. All four sets had their initial moisture content adjusted to 60% but one of each duplicate pair had its moisture content adjusted to 60% during the entire period of further composting in windrows. The rate of further (windrow) composting was significantly different in the litter which contained no bacterial product and which only had its moisture content adjusted at the beginning of the experiment. Decomposition was incomplete in this set even after day 91. In the three other sets, the rate of decomposition was faster and the spent litter became stabilised by day 56. This result suggests that if the bacterial product has been added during the initial pig-on-litter composting process, moisture adjustment during further (windrow) composting is not important. Conversely, if moisture was adjusted during further composting, the addition of bacterial product during initial pig-on-litter composting would be of no value. Such a finding is of remarkable significance in the further composting of spent litter since this indicates that the process could be run on a much more economical basis.     

Composting of vegetable waste in subtropical climates

This experiment examined the possibility of using composting as a method of waste disposal in subtropical countries, such as the United Arab Emirates (UAE), where temperatures are high and humidity is low. In order to simulate conditions in the UAE, a representative mixture of wastes generated in the UAE was prepared and tested at ambient temperatures resembling those of subtropical countries. The mixture consisted of tomatoes, cabbage, eggplant and grass. The addition of grass (40% of the mixture by weight) adjusted the carbon/nitrogen ratio and the moisture content of the compost to the necessary level for initiating decomposition. To maintain the moisture content of the compost under severe dry hot weather, a saturated insoluble polymer (IP) was added at 20% and 60% concentration (wet weight). The mixture was then composted at three different temperatures. Results showed that the mixture requires about two weeks for stabilisation. High temperature is an advantage to the compost process; at temperatures between 40 and 60°C, the waste mixture (regardless of IP concentration) decomposed quicker than at low temperature (25°C). The addition of 20% saturated IP to the compost increases the moisture content and decomposition rate. It also increases the organic chemical content of the compost, which will be reflected by microbial activity.     

Removal of two cationic dyes from a textile effluent by filtration-adsorption on wood sawdust

BACKGROUND: Wastewater from textile industry contains various contaminants such as dyes, surfactants and heavy metals. Textile dyes have synthetic origin and complex aromatic molecular structures that make them difficult to biodegrade when discharged in the ecosystem. The objective of this study was to examine the decolourisation of textile effluents containing cationic dyes by filtration-adsorption on wood sawdust from two different origins; fir as an example of a conifer tree, and beech as an example of a deciduous one, and to explain the adsorption mechanism. METHODS: The process of dye removal was applied to a synthetic effluent in batch mode. Adsorption experiments were performed by suspending sawdust in the effluent and analyzing the supernatant by spectrophotometry. The effectiveness of the treatment process was evaluated by measuring coloration. RESULTS AND DISCUSSION: Experimental results showed a significant potential for wood sawdust, especially coniferous sawdust, to remove cationic dyes from textile effluents. Adsorption kinetics was influenced by the initial dye concentration, nature and amount of sorbent as well as sorbent particle size. The adsorption followed a pseudo first-order kinetics. For both basic dyes, the Langmuir adsorption equation showed a better fit than the Freundlich equation. CONCLUSION: Filtration-adsorption using an inexpensive and readily available biosorbent provided an attractive alternative treatment for dye removal, and it does not generate any secondary pollution. Recommendations and Perspectives. Laboratory studies provide promising perspectives for the utilization of wood sawdust as renewable adsorbent for reducing pollution while enhancing the reuse of textile effluents. However, the treatment process needs to be applied to the other textile dye classes in order to be used on an industrial scale.     

接种比对餐厨垃圾干式厌氧发酵启动的影响

针对不同接种比对餐厨垃圾干式厌氧发酵启动的影响,对比分析了VS接种比分别为0.36和0.90两种情况下,餐厨垃圾干式厌氧发酵启动过程中pH、NH4-N、COD、VFA、甲烷含量等指标的变化。实验结果表明,启动初期2组样品pH分别快速降至4.74和5.68,均呈酸化状态,经碱液调整后,接种比为0.36的处理仍无法正常产气,接种比为0.90的处理,pH逐步提高,系统正常运行,经72 d的发酵实验,COD去除率达90.29%,甲烷含量高于60%的沼气产量达255.4 L,分析可见,VS接种比是干式厌氧发酵处理的重要参数;此外,与传统湿式厌氧发酵处理相比,餐厨垃圾干式厌氧发酵在较高的VFA和氨氮浓度下,仍能正常运行,采用干式厌氧发酵技术处理餐厨垃圾是可行的。     

Parameters affecting azoxystrobin and imidacloprid degradation in biobed substrates in the North Indian tropical environment

Abstract

This study reports degradation of azoxystrobin (AZOXY) and imidacloprid (IMIDA) in the rice straw (RS)/corn cob (CC) and peat (P)/compost (C)-based biomixtures. The effect of biomixture preconditioning (10?days incubation prior to pesticide application), pesticide concentration and moisture content was evaluated. Results suggested that conditioning of biomixture greatly affected IMIDA degradation where half-life (t_1/2) was reduced by 5–9 times. This was attributed to higher microbial biomass carbon content and dehydrogenase activity in the conditioned biomixtures. Pesticide application in the conditioned biomixture did not show any negative impact on soil microbial parameters. Both pesticides degraded at faster rate in the rice straw-based biomixtures than in the corn cob-based biomixtures. Degradation slowed down with increase in initial concentration of pesticides in biomixture and 1.6–3.0 (AZOXY) and 2.4–3.6 (IMIDA) times increase in t_1/2 values was observed. The moisture content of biomixture showed positive effect on degradation which increased when moisture content was increased from 60 to 80% water holding capacity. The effect was significant for IMIDA degradation in the corn cob-based biomixtures and AZOXY degradation in the peat biomixtures. The rice straw-based biomixtures were better in degrading AZOXY and IMIDA and can be used in biopurification systems.     

污泥加热预处理对中温厌氧消化的影响

对污泥加热预处理给中温厌氧混合消化和污泥单独消化带来的影响进行了研究.研究结果表明,污泥加热预处理有利于提高混合消化对 COD 的去除率,尤其是 SCOD 的去除率由 77%增长到 93%,但不利于 TS 和 VS 的去除;而对污泥单独消化,预处理则不利于有机物的去除.采用加热预处理后的污泥进样,混合消化和污泥单独消化的甲烷产气量均有所提高.