Determination of n-alkanes and polycyclic aromatic hydrocarbons in atmospheric particulate and vapour phases in Oviedo, Spain, by GC-MS

A GC-MS procedure for the determination of hydrocarbons in air samples from Oviedo, Spain, was developed. Air hydrocarbons were sampled with a high volume sampler equipped with a holder containing a glass fiber filter, to trap the particulate phase, and two polyurethane foams to capture hydrocarbons of the vapour phase. Compounds were extracted with CH2Cl2 by Soxhlet extraction and then fractionated using column chromatography with alumina silica. Analyses of the fractions were performed by GC-MS in the electron ionization mode. PAHs and n-alkanes were the compounds examined in this work. Samples collected in the vicinity of the Faculty of Chemistry (a semi-urban area) were analysed. The total concentration of PAHs in the air samples analysed ranged from 28 to 76 ng m(-3). The total concentration of n-alkanes and PAHs in the vapour phase exceeded the concentration in the particulate phase in the samples analysed.     

Molecular characterisation of organic material in air fine particles (PM10) using conventional and reactive pyrolysis-gas chromatography-mass spectrometry

Pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS) was applied to study the composition of organic constituents in air particulate matter (PM10) collected inside an industrial area. A few milligrams of sampling filters containing air particles were pyrolysed at 700 degrees C directly (conventional) or after the addition of a derivatising reagent (tetramethylammonium hydroxide, TMAH, for pyrolysis-methylation; hexamethyldisilazane, HMDS, for pyrolysis-silylation). Py-GC-MS was also applied to synthetic polymers (poly(styrene-co-isoprene), polylimonene and polypinene) and vegetation samples (coniferous pollen, bark and resin) to identify markers indicative of possible precursors. Pyrolysates of PM10 showed the same suite of compounds in all the four seasons, dominated by hydrocarbons like styrene, limonene and clusters of isomeric alkenes with 14, 15 and 16 carbon atoms. Pyrolysis products of natural origin, including furaldehyde, benzeneacetonitrile, dehydroabietin and other diterpenoids were found, while no specific markers of synthetic rubbers were detected. The principal products released from reactive pyrolysis of PM10 were methyl or trimethylsilyl (TMS) derivatives of 1,6-anhydroglucose (levoglucosan), fatty acids, dehydroabietic acid and other resin acids along with hydroxy (di)carboxylic acids. Possible sources of the detected products (e.g. pine forest, biomass combustion) are discussed.     

GC-MS检测济南市东部空气中气相与颗粒物上有机污染物

用GDX-101吸附剂和玻璃纤维滤膜(GF)同时采集气相和颗粒物上有机污染物,样品经提取分离后用GC-MS进行定性分析.结果表明,颗粒物上有机污染物的种类和含量都高于气相,工业区空气中有机污染较生活区严重,仍以燃煤、燃油污染为主.     

Saharan dust contribution to PM₁₀, PM₂.₅ and PM₁ in urban and suburban areas of Rome: a comparison between single-particle SEM-EDS analysis and whole-sample PIXE analysis

From February 15th to April 15th 2009, a period characterised by two episodes of Saharan dust outbreaks in Italy, particulate matter (PM) samples were collected at two stations (urban and suburban) in Rome. Some samples were selected and analysed using the SEM-EDS technique to characterise PM, focussing especially on the mineral contribution. Samples were representative both of days affected by Saharan dust episodes and days without this contribution. Cluster analysis allowed the attribution of each of about 67,000 analysed particles to one of the seven main statistical groups based on their composition. Characteristics of the particulate components identified using SEM-EDS analysis were verified by PIXE analysis carried out on filters collected in a suburban area. Ultimately, the contribution of crustal particles was revealed to be consistently high, highlighting the importance of local and regional mineral contributions, as well as those of Saharan origin. Therefore, quantifying all mineral contributions to resuspended particulate could lead to significant reductions of the PM level also on days not influenced by Saharan dust, thus limiting conditions when PM?? daily limit value (DLV) established by European legislation is exceeded.     

Analysis of per- and polyfluorinated alkyl substances in air samples from Northwest Europe

Air samples were collected from 4 field sites in Europe: 2 sites from the UK, Hazelrigg (semi-rural) and Manchester (urban); 1 site from Ireland: Mace Head (rural); and 1 site from Norway: Kjeller (rural). Additionally, air samples were taken from indoor locations in Troms?, Norway. Air samples were collected using high-volume air samplers employing sampling modules containing glass-fibre filters (GFFs, particle phase), and glass columns with a polyurethane foam (PUF)-XAD-2-PUF sandwich (gaseous phase). Typical outdoor air volumes required for the determination of per- and polyfluorinated alkyl substances (PFAS) ranged from 500-1800 m3. GFFs and PUF-XAD columns were analysed separately to obtain information on phase partitioning. All air samples were analysed for volatile, neutral PFAS, with selected GFF samples halved for analysis of both neutral and airborne particle-bound ionic PFAS. Volatile PFAS were extracted from air samples by cold-column immersion with ethyl acetate, and were analysed by gas chromatography-mass spectrometry in the positive chemical ionisation mode (GC-PCI-MS). Ionic PFAS were extracted from GFFs by sonication in methanol, and were analysed by liquid chromatography-time-of-flight-mass spectrometry (LC-TOF-MS) using electrospray ionisation in the negative ion mode (ESI-). Perfluorooctanoate (PFOA) was often the predominant analyte found in the particulate phase at concentrations ranging from 1-818 pg m(-3), and 8:2 fluorotelomer alcohol (FTOH) and 6:2 FTOH were the prevailing analytes found in the gas phase, at 5-243 pg m(-3) and 5-189 pg m(-3), respectively. These three PFAS were ubiquitous in air samples. Many other PFAS, both neutral and ionic, were also present, and levels of individual analytes were in the 1-125 pg m(-3) range. Levels of some PFAS exceeded those of traditional persistent organic pollutants (POPs). In this study, the presence of 12:2 FTOH and fluorotelomer olefins (FTolefins), and ionic PFAS other than perfluorooctane sulfonate (PFOS) and PFOA, are reported in air samples for the first time. Concentrations of neutral PFAS were several orders of magnitude higher in indoor air than outdoor air, making homes a likely important diffuse source of PFAS to the atmosphere. Our repeated findings of non-volatile ionic PFAS in air samples raises the possibility that they might directly undergo significant atmospheric transport on particles away from source regions, and more atmospheric measurements of ionic PFAS are strongly recommended.     

Analysis of acidic components, heavy metals and PAHS of particulate in the Changwon–Masan area of Korea

This study is an analysis of the concentrations and components of heavy metals in PM_2.5 and the total suspended particulate (TSP) collected at a mechanical industrial complex (IC) site in Changwon and at a residential site in Masan, Korea. Particulate was collected during two sampling periods, from the late summer to the early fall and from the middle to late fall, at the IC site and one sampling period, from the middle fall to the early winter, at the residential site. PM_2.5 and TSP samples were taken by an annular denuder system and a hi-volume air sampler, respectively. The authors also identified the concentrations and components of heavy metals extracted from the PM_2.5 and TSP filters, the acidic components extracted from the PM_2.5 filters, and the polycyclic aromatic hydrocarbons (PAHs) extracted from polyurethane foam (PUF) plug. The average concentrations of the PM_2.5 collected at the IC and residential sites were very similar. Major sources of PM_2.5 at the study sites, however, were air emissions from vehicles and industry as well as emissions from residential heating and soil origins, respectively. The higher concentrations of the TSP at the IC site, as compared to those at the residential site, were due to either increased suspended dust from vehicle emissions or re-suspended road dust because of increased vehicle speeds near the IC site. Heavy metal concentrations in the TSPs were higher than those in the PM_2.5. The heavy metal concentrations in the PM_2.5 and TSP at the IC site with heavy traffic were substantially greater than those at the residential site. The concentrations of TSP and heavy metals and PAHs in PM during the period of the middle to late fall was much higher than those during the period of the late summer to early fall at the IC site. This is because of the difference in meteorological characteristics and energy uses between two periods. The residential site also showed higher concentrations of acidic anions while the IC site showed higher concentrations of acidic cation. Secondary aerosols or particulates, such as ammonium nitrate or ammonium nitrite, might have been important constituents of the PM_2.5 at the residential site. The PAHs in the TSP collected at the IC site was greatly affected by traffic and industry emissions consisting mostly of high molecular weight PAHs with two to four rings. PAHs in the TSP at the site, however, were affected by residential heating and air emissions from small chemical plants having higher concentrations of low molecular weight PAHs with five to six rings.     

Characterisation of particulate matter on the receptor level in a city environment

Airborne particulate matter (PM) has become one of the dominant pollutants with the increasing material and energy demand due to global economic growth. The main objective of this research is to provide a comprehensive receptor level characterisation of the particulate matter collected in a city environment. Particulate matter samples were collected on Tapered Element Oscillating Microbalance (TEOM) filters from five monitoring sites over a period of 1 year. An Andersen eight-stage cascade impactor was also used to collect airborne PM samples from three other locations to compare with the samples collected by TEOM. All the samples were then subjected to individual particle morphology and chemical composition analysis by SEM/EDS. Bulk chemical composition of the samples were also analysed through ICP–OES. Based on these analyses, possible sources of the PM samples were identified. The results showed that the monitoring sites in residential environments were dominated by transportation-derived particles and other migratory particulates. Monitoring sites near the city centre were dominant by particles from transportation, with biological particles abundant for the site closer to a river. The monitoring station located close to the industrial area, despite only 200 m away from a motorway, has low contribution of non-exhaust particulates from vehicles. Instead, the particulates collected from this site were dominated by industrial sources. An air dispersion modelling package was also used to model the particulate matter dispersion in the city area for the period of sampling. The results from the model showed that the points of high emissions were around industrial areas.     

Characterization of Organic Compounds in Compost-Amended Soil

Samples of compost-amended soil from waste dumping sites in Lagos Metropolis were extracted with dichloromethane (3 × 20 cm³) and the extract was evaporated at 35 °>C. The residue was extracted with 2,2,4-trimethylpentane, and portions of the solution were applied to a column containing silica gel from which aliphatic and aromatic hydrocarbons were eluted with n-hexane and toluene respectively. Analysis of the n-hexane fraction using gas chromatography showed the presence of a mixture of aliphatic hydrocarbons, ranging from C₉ to C₂₅, while ultraviolet analysis of the toluene fraction suggested 1,2-benzanthracene; 2,3-benzphenanthrene, chrysene and pyrene as polyaromatic compounds present in samples analyzed. The crude extracts were highly coloured and viscous. Total extractable organic residues in the 2,2,4-trimethylpentane extracts ranged from 36 to 89 mg g^-1 of soil.     

Organophosphates in aircraft cabin and cockpit air--method development and measurements of contaminants

Methods for measurements and the potential for occupational exposure to organophosphates (OPs) originating from turbine and hydraulic oils among flying personnel in the aviation industry are described. Different sampling methods were applied, including active within-day methods for OPs and VOCs, newly developed passive long-term sample methods (deposition of OPs to wipe surface areas and to activated charcoal cloths), and measurements of OPs in high-efficiency particulate air (HEPA) recirculation filters (n = 6). In total, 95 and 72 within-day OP and VOC samples, respectively, have been collected during 47 flights in six different models of turbine jet engine, propeller and helicopter aircrafts (n = 40). In general, the OP air levels from the within-day samples were low. The most relevant OP in this regard originating from turbine and engine oils, tricresyl phosphate (TCP), was detected in only 4% of the samples (min-max 相似文献   

Comparison of tanker drivers' occupational exposures before and after the installation of a vapour recovery system

The purpose of this study was to compare tanker drivers' occupational exposure level before and after the installation of vapour recovery facilities at 14 service stations. Road tanker drivers are exposed when handling volatile petrol liquid in bulk in the distribution chain. The drivers' exposure was studied during the unloading operation as the bulk petrol flowed into underground storage tanks, displacing vapours in the tank space and causing emission to the environment and the drivers' work area. The exposures were measured again when the dual point Stage I vapour recovery systems were installed for recycling vapours. Short-term measurements were carried out in the drivers' breathing zones by drawing polluted air through a charcoal tube during unloading. The samples were analysed in the laboratory by gas chromatography for C3-C11 aliphatic hydrocarbons, tert-butyl methyl ether (MTBE), tert-amyl methyl ether (MTAE), benzene, toluene and xylene. The road tanker loads delivered consisted of oxygenated and reformulated petrol (E95 and E98 brands), which contained on average 13% oxygenates. Before the installation of the vapour recovery system, the geometric mean (GM) concentration of aliphatic hydrocarbons was 65 mg m-3 (range 6-645 mg m-3) in the drivers' breathing zones. After the installation at the same service stations, the corresponding exposure level was 8.3 mg m-3 (range < 1-79 mg m-3). The GM of the MTBE concentrations was 8.6 mg m-3 (range 1-67 mg m-3) without vapour recovery and 1.5 mg m-3 (range < 0.1-10 mg m-3) with vapour recovery. The differences between the aliphatic hydrocarbons and the MTBE exposure levels during the unloading of the road tankers without and with vapour recovery were statistically significant (p < 0.05).     

大气颗粒物手工比对监测体系滤膜称量质控技术探讨

健全大气颗粒物手工比对监测体系是"十三五"环境空气自动监测质量管理的一项重点任务,其中颗粒物滤膜的称量直接影响手工监测数据质量。研究调研了国内各级环保部门所属环境监测机构颗粒物滤膜称量工作情况,结合国内外方法标准、技术规范等,重点探讨了称量实验室环境、称量设备、称量影响因素等滤膜称量质控要点,并针对环境管理与监测需求对大气颗粒物手工比对监测滤膜称量质控提出建议。     

Morphology,microstructure and chemical composition of single inhalable particles in Shanghai,China

The morphology, microstructure, and chemical composition of a variety of particles emitted from coal-fired power plants, steel plants, and vehicle exhausts, which are possible sources of particulate matter (PM) in the atmosphere, were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) and compared with particle samples collected from urban atmosphere to identify the best footprint or the suitable indicator relating the existence of studied particles and their possible emitters by the morphology, microstructure, and chemical composition of the particles. The investigation indicated that the particles from these three sources are different in morphology, microstructure, and chemical composition. Sphere aggregates were generally the most abundant components, with silicon and aluminum as major elements. The urban air particulate contained particles similar to those observed in the power plant, steel plant, and vehicle exhaust samples suggesting that all three sources are contributing to the pollution in the city.     

Characterization and diurnal variation of size-resolved inorganic water-soluble ions at a rural background site

Water-soluble inorganic ions in aerosol samples have been studied. The sample collection took place during summer in 2003 at a European background site which is operating within the framework of the European Monitoring and Evaluation Program. Gent type PM10 stacked filter unit (SFU) samplers were operated in parallel on a day and night basis to collect particles in separate coarse (2.0-10 microm) and fine (<2.0 microm) size fractions. Particulate masses were measured gravimetrically; the filters from one of the SFU samplers were analyzed by particle-induced X-ray emission spectrometry (PIXE) and instrumental neutron activation analysis (INAA). Filters from the other SFU sampler were analyzed by ion chromatography (IC) for major inorganic anions (MSA-, NO2(-), NO3(-), Cl-, Br-, SO4(2-), oxalate) and cations (Na+, K+, NH4(+), Mg2+, Ca2+). The water-soluble inorganic ions measured were responsible for 44% and 16% of the total fine and coarse particulate mass, respectively. In the fine size fraction, the main ionic components were SO4(2-) and NH4(+) accounting for about 90% of fine ionic mass. In the coarse fraction the main ionic components were Ca2+ and NO3(-), followed by SO4(2-). Significant day and night difference in the mass concentrations was observed only for fine NO3(-). The molar ratios of fine NH4(+) to SO4(2-) indicated their complete neutralization to (NH4)2SO4. According to the cation-to-anion ratios the coarse particles were alkaline, while the fine particles were slightly acidic or neutral. By comparing the corresponding concentrations obtained from PIXE/INAA and IC, we determined the water-extractable part of the individual species. We also investigated the effect of long-range transported air masses on the local air concentrations, and we found that the air quality of this background monitoring station was affected by regional pollution sources.     

Preparation, certification and interlaboratory analysis of workplace air filters spiked with high-fired beryllium oxide

Occupational sampling and analysis for multiple elements is generally approached using various approved methods from authoritative government sources such as the National Institute for Occupational Safety and Health (NIOSH), the Occupational Safety and Health Administration (OSHA) and the Environmental Protection Agency (EPA), as well as consensus standards bodies such as ASTM International. The constituents of a sample can exist as unidentified compounds requiring sample preparation to be chosen appropriately, as in the case of beryllium in the form of beryllium oxide (BeO). An interlaboratory study was performed to collect analytical data from volunteer laboratories to examine the effectiveness of methods currently in use for preparation and analysis of samples containing calcined BeO powder. NIST SRM(?) 1877 high-fired BeO powder (1100 to 1200 °C calcining temperature; count median primary particle diameter 0.12 μm) was used to spike air filter media as a representative form of beryllium particulate matter present in workplace sampling that is known to be resistant to dissolution. The BeO powder standard reference material was gravimetrically prepared in a suspension and deposited onto 37 mm mixed cellulose ester air filters at five different levels between 0.5 μg and 25 μg of Be (as BeO). Sample sets consisting of five BeO-spiked filters (in duplicate) and two blank filters, for a total of twelve unique air filter samples per set, were submitted as blind samples to each of 27 participating laboratories. Participants were instructed to follow their current process for sample preparation and utilize their normal analytical methods for processing samples containing substances of this nature. Laboratories using more than one sample preparation and analysis method were provided with more than one sample set. Results from 34 data sets ultimately received from the 27 volunteer laboratories were subjected to applicable statistical analyses. The observed performance data show that sample preparations using nitric acid alone, or combinations of nitric and hydrochloric acids, are not effective for complete extraction of Be from the SRM 1877 refractory BeO particulate matter spiked on air filters; but that effective recovery can be achieved by using sample preparation procedures utilizing either sulfuric or hydrofluoric acid, or by using methodologies involving ammonium bifluoride with heating. Laboratories responsible for quantitative determination of Be in workplace samples that may contain high-fired BeO should use quality assurance schemes that include BeO-spiked sampling media, rather than solely media spiked with soluble Be compounds, and should ensure that methods capable of quantitative digestion of Be from the actual material present are used.     

Advanced techniques for characterization of organic matter from anaerobically digested grapemarc distillery effluents and amended soils

The effects of grapemarc distillery effluents on the quality of soil organic matter is extremely important to ensure the environmentally-safe and agronomically efficient use of these materials as organic amendment. In this work, the effects of the application of untreated (UG) and anaerobically digested grapemarc distillery effluents, either added with (AGM) or without mycorrhiza (AG), on soil humic acid (HA) were investigated in field plot experiments in comparison to HAs from a control soil and an inorganic fertilized soil. The humic acid-like fractions (HALs) isolated from UG, AG and soils were characterized for compositional, structural and functional properties by the use of elemental and functional group analysis, and ultraviolet/visible, Fourier transform infrared and fluorescence spectroscopies. Results obtained indicated that anaerobic digestion of effluents produced an extended mineralization with loss of organic C and stabilization of residual organic matter by increasing the content of HALs in the effluent. With respect to control soil HA, HALs isolated from UG and AG were characterized by smaller acidic functional group contents, a prevalent aliphatic character and smaller aromatic polycondensation and humification degrees. The chemical and spectroscopic characteristics of native soil HA were not substantially modified by application of UG, AG and AGM to soil, which suggests the occurred incorporation of the effluent HAL into native soil HA. In conclusion, these results showed the possibility of a beneficial and safe recycling of grapemarc distillery effluents as soil amendment.     

Aliphatic and polycyclic aromatic hydrocarbons in the surface sediments of the Mediterranean: assessment and source recognition of petroleum hydrocarbons

Coastal marine sediment samples were collected from ten sampling stations along the Egyptian Mediterranean coast in April 2010. All sediment samples were analyzed for aliphatic (C7 to C34) and polycyclic aromatic hydrocarbons (PAHs) as well as total organic carbon (TOC) contents and grain size analysis. Total aliphatic hydrocarbons ranged from 1621.82 to 9069.99 ng/g (dry weight), while aromatic hydrocarbons (16 PAHs) varied between 208.69 and 1020.02 ng/g with an average of 530.68?±?225.86 ng/g?dwt. Good correlations observed between certain PAH concentrations allowed to identify its origin. The average TOC percent was varied from 0.13 to 1.46 %. Principal component analysis was used to determine the sources of hydrocarbon pollutants in sediments of Mediterranean. Additionally, special PAHs compound ratios suggest the petrogenic origins.     

Occupational exposure to rubber vulcanization products during repair of rubber conveyor belts in a brown coal mine

Several hundred chemical compounds were found in workroom environments in the rubber industry, but most of the published exposure data relate to the production of tyres; information from the "non-tyre" sections are very limited, if any. This study was carried out to identify chemical substances and measure their air concentrations in the repair shop of a brown coal mine in which damaged rubber conveyor belts were repaired. GC-MS and HPLC analysis of stationary air samples resulted in identification of aliphatic and aromatic hydrocarbons to C12, PAHs, alcohols, phenols, ketones, heterocyclic nitrogen and sulfur compounds. Quantitative evaluation of occupational exposure included determination of organic compound vapours collected on charcoal (GC-MSD), polycyclic aromatic hydrocarbons (HPLC), N-nitrosoamines and other amines (GC-NPD) and DNPH derivatives of aldehydes (HPLC) in the breathing zone of workers representing all job titles. The concentrations of investigated compounds were very low. Carcinogenic substances: N-nitrosoamines, benzene, PAHs were not present in workroom air in concentrations exceeding limits of detection of the analytical methods being applied; concentrations of methylisobutylketone, tetrachloroethylene, naphtha, aromatic hydrocarbons, phthalates and aldehydes were much lower than the respective occupational exposure limit values. The results indicate much lower exposure than that reported in the production of tyres and other fabricated rubber products.     

Development and comparison of methods using MS scan and selective ion monitoring modes for a wide range of airborne VOCs

Adsorbent sampling with analysis by thermal desorption, gas chromatography and mass spectrometry (TD/GC/MS) offers many advantages for volatile organic compounds (VOCs) and thus is increasingly used in many applications. For environmental samples and other complex mixtures, the MS detector typically is operated in the scan mode to aid identification of co-eluting compounds. However, scan mode does not achieve the optimal sensitivity, thus compounds occurring at low concentrations may not be detected. This paper develops and evaluates the application of a more sensitive TD/GC/MS method using selective ion monitoring (SIM) that is applicable to VOC mixtures found in ambient and indoor air. Based on toxicity and prevalence, 94 VOCs (including terpenes, aromatic, halogenated and aliphatic compounds) were selected as target compounds. Two analytical methods were developed: a conventional full scan method for ions from 29 to 270 m/z; and a SIM method using 16 time windows and different ions selected for the compounds in each window. Both methods used the same Tenax GR adsorbent sampling tubes, TD and GC parameters, and target and qualifier ions. Laboratory tests determined calibrations, method detection limits (MDLs), precisions, recoveries and storage stability. Field tests compared scan and SIM mode analyses for duplicate samples of indoor air in 51 houses and outdoor air at 41 sites. Statistical analyses included the development of error/precision models. The laboratory tests showed that most compounds demonstrated excellent precision (<10% for concentrations exceeding approximately 0.5 microg m(-3)), good linearity, near identical calibrations for scan and SIM modes, a wide dynamic range (up to 1500 microg m(-3)), and negligible storage losses after 1 month (7 compounds showed moderate losses). SIM mode MDLs ranged from 0.004 to 0.27 microg m(-3), representing a modest (1.1 to 22-fold) improvement compared to scan mode. However, in field tests the SIM method detected significantly more compounds (e.g., styrene and chloroform). Error models fit most compounds and allow quantification of errors at selected percentiles. Overall, while the new SIM method is somewhat time-consuming to develop, it offers greater sensitivity and maintains the high selectivity of traditional scan methods.     

石家庄市春季大气颗粒物的铅污染特征

为了解石家庄市2016年春季大气颗粒物的铅污染特征及来源,利用单颗粒气溶胶质谱仪(SPAMS),分析了大气中含铅颗粒的化学成分。结果表明: 研究期间大气环境中含铅颗粒数浓度共出现11次跳跃式升高,跳跃时间段内石家庄均处于轻度污染过程。从成分分析来看,含铅颗粒分为纯铅颗粒、Pb与K(Pb-K)、OC(Pb-OC)、Cl(Pb-Cl)、混合颗粒等八大类。观测结果表明:Pb-K颗粒最多,占到含铅颗粒的84.4%；其次为纯铅颗粒,占比为13.0%。与石家庄市污染源谱库比对进行来源解析,得到Pb-K颗粒主要来自生活垃圾焚烧源, 纯铅颗粒主要来自工业源。结合石家庄市大气污染源排放清单和后向气流轨迹分析,推测含铅颗粒可能来自市区西南方向某区县的生活垃圾焚烧企业。