水中痕量砷的富集测定方法

实验部分 一、巯基棉的制备方法:取硫代乙醇酸20ml、乙酸酐14ml,混匀后加入浓硫酸2滴,摇匀并冷却至室温,加脱脂棉4g浸湿,室温放置24小时以上。用蒸馏水洗至中性、挤干残存水,放入37～38℃烘箱中烘干后放入棕色磨口瓶中保存。在避光、密闭、较低温度下可保存一年以上。 二、冷原子荧光法间接测定痕量砷的方法: 分别加入0,0.4,0.8,1.2,1.5μg As于含100ml去离子水的砷化氢发生瓶中,再加入1:1硫酸13ml,20％碘化钾2ml,40％氯化亚锡5ml,摇匀后煮沸5min。冷却后加无砷锌粒4g,生成的砷化氢通过10％醋酸铅溶液     

AgDDC光度法测定水中砷的相关问题

1在过滤前必须将滤纸用小毛刷轻轻刷一遍 ,再用蒸馏水冲洗干净后晾干备用 ,以免纤维进入吸收液。2氯化亚锡溶液应临用现配 ,以免被氧化失去还原作用。3使用 1 4～ 2 0目或 1 6个 /克规格的无砷锌粒以保证分析结果准确。 4为控制反应速度 ,可当砷化氢发生瓶加完试剂放置 1 5min后放入盛有冰水的托盘中 ,取 5.0 ml吸收液于干燥的吸收管中 ,插入导气管 ,再将 4g( 1 4～ 2 0目 )锌粒迅速倾入砷化氢发生瓶中 ,立即将导气管与发生瓶连接 ,保证不漏气 ,在室温下反应 1小时。5可用蒸馏法回收氯仿 ,温度不可过高 ,微沸即可 ,初馏液可加少量无水氯化钙…     

纳米金修饰分子印迹聚合膜电极检测双酚A

以纳米金修饰玻碳电极为基础电极,以双酚A为模板分子,以邻氨基苯硫酚为聚合单体,采用循环伏安法电聚合制备分子印迹聚合膜,利用循环伏安和交流阻抗法研究电极的电化学特性。结果表明,双酚A在修饰电极表面的反应是一个受吸附控制的等电子、质子转移的不可逆反应。采用差分脉冲伏安法检测双酚A,线性范围为5. 0×10~(-6)mol/L～4. 0×10~(-4)mol/L,检出限为2. 3×10~(-7)mol/L。将该电极用于自来水和牛奶样品的测定,结果均为未检出,加标回收率分别为93. 5%和95. 4%,3次测定结果的RSD分别为4. 0%和5. 7%。     

加速溶剂萃取-高效液相色谱法测定土壤中16种多环芳烃

研究了土壤中的16种多环芳烃的提取和测定方法.结果表明,用加速溶剂提取仪在100℃,二氯甲烷和丙酮(1:1)提取5min,再经硅胶柱净化,正己烷和二氯甲烷(3:2)洗脱,25℃氮吹浓缩后用高效液相色谱测定可以得到很好的效果,方法回收率在58%～106%之间,检测限为1.4×10-4～3.6×10-2mg/kg,且重现性好.     

悬浮液直接进样石墨炉原子吸收法测定湖泊底泥中的铅

试验了悬浮液直接进样平台石墨炉原子吸收分光光度法测定湖泊底泥中的铅。方法特征灵敏度为2 1× 10 -11g/ 0 0 0 44 (A·s) ,检测限 (3σ)为 2 5× 10 -11g ,相对标准差 (n =6 )小于 4% ,加标回收率在 90 %～ 110 %之间     

固相萃取富集高效液相色谱法测定环境水样中的重金属元素

研究了用固相萃取富集高效液相色谱法测定环境水样中痕量重金属镍、铜、银、铅、镉和汞的方法。环境水样中的镍、铜、银、铅、镉和汞用四 -(对二甲氨基苯基 ) -卟啉 (T4 -DMAPP)柱前衍生 ,用C18固相萃取小柱萃取富集镍、铜、银、铅、镉和汞的T4 -DMAPP络合物 ,富集倍数为 1 0 0倍 ,然后用甲醇和四氢呋喃梯度洗脱为流动相 ,WatersXter raTMRP18( 3 9mm× 1 5 0mm)色谱柱为固定相分离 ,用二极管矩阵检测器检测。镍、铜、银、铅、镉和汞的检测限分别为3、2、4、3、1 5ng/L和 3ng/L。方法相对标准偏差为 1 8%— 3 2 % ,标准回收率为 92 %— 1 0 7%。该方法用于测定环境水样中的痕量重金属 ,结果令人满意     

5-氯-2-(吡啶偶氮)-1,3-二氨基苯分光光度法测定水质钴

采用5-氯-2-(吡啶偶氮)-1,3-二氨基苯分光光度法测定水质钴。对分析方法的样品前处理、样品保存、样品分析条件、干扰消除、检出限及测定范围、实际样品测定进行了深入研究和技术改进。水样经消解后测定的方法检出限为0.009 mg/L,经富集后测定的方法检出限为4×10-4mg/L,干扰消除实验的回收率为96%~101%,地表水、地下水、生活污水及工业废水等4种类型水样的加标回收率为92%~103%。     

固相萃取-高效液相色谱法测地表水中11种酚类化合物

建立了固相萃取-高效液相色谱法同时测定地表水中11种酚类化合物的方法。水样经过全自动固相萃取仪富集,以HLB柱为萃取柱,乙腈(含1%乙酸)为洗脱剂,用高效液相色谱仪分析定量。该方法在0.5~5.0 mg/L范围内线性良好,相关系数为0.999 6~0.999 9,11种酚类化合物的纯水加标回收率为82.0%~111%,地表水加标回收率为98.5%~116%,精密度为3.58%~4.67%,检出限为1×10-4~5×10-4mg/L,该方法简单实用、准确可靠,可用于地表水中酚类化合物的同时测定。     

火焰原子吸收法间接测定水中硫化物的方法

取适量 S2 -标准溶液 ( 0 .0 1 mg/ml)于 2 5ml刻度管中 ,加 1 .0 ml浓度为 0 .1 mg/ml Cu2 标液 ,4 .0 ml HAc- Na Ac缓冲溶液 ( p H4 .5) ,稀至刻度摇匀。于 55℃水浴中加热 1 5min,冷至室温 ,用双层滤纸过滤 ,分离硫化铜沉淀 ,弃去前 1 5ml初始滤液 ,接中间滤液 ,用原子吸收法测定滤液中剩余Cu2 ,从而间接求出 S2 -含量。硫含量为 1 .2 μg/ml时 ,Mg2 等 1 1种离子含量为 4 0～ 80 μg/ml时无干扰 ,SO2 -3 含量大于 4 0μg/ml时存在负干扰。回收率 93%～ 94 .7% ,n=7时变异系数为3.2 %。火焰原子吸收法间接测定水中硫化物的方法@…     

毛细管气相色谱法快速测定化妆品中4种对羟基苯甲酸酯防腐剂

用乙醇萃取了化妆品中的4种防腐剂(对羟基苯甲酸甲酯、对羟基苯甲酸乙酯、对羟基苯甲酸丙酯、对羟基苯甲酸丁酯),用毛细管气相色谱法实现了快速分离测定,并用色谱-气相质谱联用技术进行了峰鉴定。分析时间为4min,方法回收率为90 8%～104 6%,检出限为0 5mg/L,线性范围为2～80mg/L,线性相关系数>0 999。     

Effect of combustion variables on PAHs emission from incineration of cellulose waste filters from acrylic industry

Incineration of cellulose waste filter from acrylic industry showed the presence of 13–16 polycyclic aromatic hydrocarbons (PAHs) from the list of 16 priority pollutants with an airflow rate of 1, 2, 3, and 4 L min^???1 in laboratory scale quartz tube vertical incinerator at 700–1,000°C at an interval of 100°C. The amount of total 16 PAHs increases with the increase in temperature with airflow rate of 1 L min^???1 and was found to be 9.4 times at 1,000°C than at 700°C. Studies at 800–1,000°C showed the decrease in total 16 PAHs with increase in airflow rate from 1 to 2 L min^???1. The amount of total 16 PAHs increases at 700, 800, and 1,000°C with increase in airflow rate from 2–4 L min^???1. At 900°C, amount of 16 PAHs decreases with increase in flow rate from 1 to 3 and increases at 4 L min^???1. The lesser amount of 2A PAHs was found at 700–900°C with airflow rates of 1–3 L min^???1, while less amount of 2B PAHs was found at 700°C and 800°C (with airflow rate of 1–2 L min^???1), at 900°C (with airflow rate of 1–3 L min^???1) and at 1,000°C (with airflow rate of 3 L min^???1). However, the sum total of 2A and 2B PAHs were found to be less at 700–900°C with airflow rate of 1–2 L min^???1.     

The determination of the extractability of selected elements from agricultural soil

Concentrations of Ag, Al, Ba, Cd, Co, Cr, Cu, Fe, K, Mn, Na, Ni, Pb, Sr, and Zn—isolated by sequential extraction steps from apple orchard soil—were analyzed by inductively coupled plasma-atomic emission spectroscopy and compared to the total amount of metal in soil determined by XRF. The extractable amount of each metal was calculated by the extraction yields of the four steps. The LODs of the different elements in all extracts ware below 3 μg/L except for Ba (steps 1 and 2), Cu (step 1), Fe (all steps), K (steps 1–3), Mn (step 2), Na (steps 1–3), Ni (step 1), Pb (steps 1 and 4), and Zn (steps 1 and 2). The highest LOD (>10 μg/L) was found for Fe, K, and Na (step 1). The recovery of all metals after four sequential extraction steps was 90–112%. The repeatability (<1.1%), the intermediate precision (<5.3%), the day-to-day reproducibility (<6.2%), and the overall uncertainty of measurement (approximately 4–8.5%) for all analyzed metals supports the choice of the method used.     

关于化学需氧量测定中化学反应的研究

研究了高氯样品COD测定中的化学反应,发现测定中产生的白色沉淀是AgCl而不是HgCl2,并推断了Cl-在COD测定中的反应机理.讨论了AgNO3、HgSO4加入量对测定结果的影响,重点分析了当AgNO3不足与过量时的数据.当试样体积20.00ml,按0.4g HgSO4络合2000mg/LCl-的比例,投加HgSO4掩蔽10000mg/L Cl-可取得满意结果.     

抑制型电导-离子色谱法测定水中无机阴离子

采用抑制型电导-离子色谱法测定生活饮用水、污水和地表水中F-、Cl-、NO2-、Br-、NO3-、PO43-、SO42-等7种无机阴离子,对清洁水样过滤后直接测定,浑浊样品离心后取上清液过滤测定。F-在0.100 mg/L~1.20 mg/L范围内、其余6种阴离子在1.00 mg/L~12.0 mg/L范围内线性良好,方法检出限为0.031 mg/L~0.47 mg/L,水样平行测定的RSD为0.9%~1.8%,加标回收率为82.6%~110%。     

Determination of CH4, CO2 and N2O in air samples and soil atmosphere by gas chromatography mass spectrometry, GC-MS

A method for determination of the climate gases CH4, CO2 and N2O in air samples and soil atmosphere was developed using GC-MS. The method uses straightforward gas chromatography (separation of the gases) with a mass spectrometric detector in single ion mode (specific determination). The gases were determined with high sensitivity and high sample throughput (18 samples h(-1)). The LOD (3sigma) for the gases were 0.10 micro L L(-1) for CH4, 20 microL L(-1) for CO2 and 0.02 microL L(-1) for N2O. The linear range (R2 = 0.999) was up to 500 microL L(-1) for CH4, 4000 microL L(-1) for CO2 and 80 microL L(-1) for N2O. The samples were collected in 10 mL vials and a 5 microL aliquot was injected on column. The method was tested against certified gas references, the analytical data gave an accuracy within +/-5% and a precision of +/-3%. The presence of < or = 10% by volume of C2H2 (often used experimentally to prevent N2 formation from N2O) did not interfere with detection for the targeted trace gases.     

磁性分散固相萃取-气相色谱法测定水中氯苯类化合物

采用磁性分散固相萃取技术富集水中氯苯类化合物，用气相色谱法测定，并对萃取剂的用量、萃取时间、解吸溶剂、氯化钠加入量等条件进行优化。试验表明，方法在0．001 mg/L～2．50 mg/L 范围内，氯苯类化合物各组分线性良好，方法检出限在0．600μg/L～5．00μg/L范围内。地表水实际水样的加标回收率为83．1％～93．4％，RSD为4．8％～7．3％。     

Metal immobilization and phosphorus leaching after stabilization of pyrite ash contaminated soil by phosphate amendments

In this study we would like to show the importance of a holistic approach to evaluation of chemical stabilization using phosphate amendments. An extensive evaluation of metal stabilization in contaminated soil and an evaluation of the leaching of phosphorus induced after treatment were performed. The soil was highly contaminated with Cu (2894 mg kg(-1)), Zn (3884 mg kg(-1)), As (247 mg kg(-1)), Cd (12.6 mg kg(-1)) and Pb (3154 mg kg(-1)). To immobilize the metals, mixtures of soil with phosphate (from H(3)PO(4) and hydroxyapatite (HA) with varying ratios) were prepared with a constant Pb : P molar ratio of 1: 10. The acetic acid extractable concentration of Pb in the mixture with the highest amount of added phosphoric acid (n(H(3)PO(4)) : n(HA) = 3 : 1) was reduced to 1.9% (0.62 mg L(-1)) of the extractable Pb concentration in the untreated soil, but the content of water extractable phosphorus in the samples increased from 0.04 mg L(-1) in the untreated soil sample up to 14.3 mg L(-1) in the same n(H(3)PO(4)) : n(HA) = 3 : 1 mixture. The high increase in arsenic mobility was also observed after phosphate addition. The PBET test showed phosphate induced reduction in Pb bioavailability. In attempting to stabilize Pb in the soil with the minimum treatment-induced leaching of phosphorus, it was found that a mixture of soil with phosphate addition in the molar ratio of H(3)PO(4) : HA of 0.75 : 1 showed the most promising results, with an acetic acid extractable Pb concentration of 1.35 mg L(-1) and a water extractable phosphorus concentration of 1.76 mg L(-1). The time-dependent leaching characteristics of metals and phosphorus for this mixture were evaluated by a column experiment, where irrigation of the soil mixture with the average annual amount of precipitation in Slovenia (1000 mm) was simulated. The phosphorus concentration in the leachates decreased from 2.60 mg L(-1) at the beginning of irrigation to 1.00 mg L(-1) at the end.     

Preconcentration of Zn2+ and Cu2+ ions from food and vegetable samples using modified activated carbon

In this work, two N/S-containing chelating agents 2-(4-methoxybenzylideneamino)thiophenol (2-4-MBAT) and 2-(4-chlorobenzylideneamino) benzenethiol (2-4-CBABT) were synthesized as new sorbents and were used for preconcentration of Zn(2+) and Cu(2+) ions in food and vegetable samples. In the proposed procedure, the trace amount of Zn(2+) and Cu(2+) ions from 250?mL of sample solution at pH?=?5.0 was preconcentrated by 1?g of activated carbon (AC) loaded with 15?mg of 2-4-MBAT and 2-4-CBABT separately. The breakthrough volumes (maximum sample volume that their metal ions quantitatively can be enriched) for solid-phase extraction (SPE) procedure based on the AC modified with 2-4-MBAT and 2-4-CBABT were 800 and 750?mL, respectively. The sorbed Zn(2+) and Cu(2+) ions were efficiently eluted by 8?mL of 4?mol?L(-1) HNO(3) and preconcentration factor of 112.5 and 93.7 and experimental enhancement factor of 30 and 35 ions were obtained for Zn(2+) and Cu(2+), respectively. The application of this enrichment procedure allowed the extraction of trace metal ions with recoveries exceeding of 90%.     

Determination of Steroid Estrogens in Wastewater Treatment Plant of A Controceptives Producing Factory

Steroid estrogens such as estrone (E1), 17β-estradiol (E2), estriol (E3), and 17α-ethynylestradiol (EE2) have been suspected to be the main contaminants, which can affect the endocrine system of animals. Many authors have investigated these chemicals in the domestic wastewater treatment plants (WTP). However, wastewater from industries producing steroid contraceptives has not got ample attention. From the environmental point of view, the four steroids are very significant because even very low concentrations (ng/L) can cause reproductive disturbances in human, livestock and wildlife. The main purpose of the present investigation was to develop an analytical method for the determination of the four steroid estrogens present in WTP of a pharmacy factory, mainly producing contraceptive medicine in Beijing, China. Analysis was performed by solid-phase extraction (SPE) system and liquid chromatography combined with tandem mass spectrometry (LC/MS/MS). The average recoveries from effluent samples ranged from 88% to 103% and the precision of the method ranged from 9% to 4%. Based on 0.5-L wastewater samples, the limit of quantification (LOQ) was determined at 0.7 ng/L for E1, 0.8 for E2, 0.9 ng/L for E3, and 0.5 ng/L for EE2 in influent, and 1.0 ng/L for E2 and EE2, and 2.0 ng/L for E1 and E3 in effluent. In the influent samples, average concentrations of 80, 85, 73 and 155 ng/L were determined for E1, E2, E3 and EE2, respectively, showing that they were removed in this WTP to the extent of 79, 73, 85 and 67%, respectively.     

高效液相色谱法测定化妆品中二苯酮-2、二苯酮-3与甲氧基肉桂酸乙基己酯

采用高效液相色谱二极管阵列检测器同时测定化妆品中二苯酮-2、二苯酮-3与甲氧基肉桂酸乙基己酯,以乙腈和水为流动相梯度洗脱,335 nm为检测波长,以保留时间和紫外光谱特征定性,外标法定量。3种化合物在1.00 mg/L~150 mg/L范围内线性良好,最低检出质量分数均为0.015%,基质加标平均回收率为96.2%~117%,RSD为0.2%~1.0%。