火焰原子吸收光谱法测定锰矿恢复区植物中重金属

采用硝酸-高氯酸消解体系、火焰原子吸收光谱法测定锰矿恢复区植物中重金属元素。方法线性良好，锰、铅、铜、铬、镉的检出限分别为0．026mg／L、0．011mg／L、0．004mg,／L、0．025mg／L、0．001mg／L，标准样品的测定结果符合要求，植物样品平行测定的RSD≤1．6％，加标回收率为83．4％-97．6％。     

微波消解ICP-AES法测定废气中铅镉砷

采用微波消解电感耦合等离子体发射光谱法同时测定废气中的铅、镉、砷,在优化的试验条件下,方法在0 mg/L～5.00 mg/L范围内线性良好,铅、镉、砷的检出限分别为0.250 μg/m3、0.125 μg/m3、0.375 μg/m3(按采样体积400 L、定容体积50 mL计),空白滤筒平行测定6次的RSD为2.3％～10.5％,加标回收率为83％ ～ 112％,与标准方法的测定结果无显著差异.     

水稻重金属含量与土壤质量的关系

根据“淮安市绿色食品基地调查以及相关研究”课题资料 ,分析了水稻中重金属含量与其土壤质量的关系。结果表明 ,重金属含量在水稻中的分布是 :根 >茎叶 >籽粒 ;水稻籽粒对重金属的吸收特点因其元素不同而差异较大 ,重金属元素被水稻糙米吸收的程度为 :砷 <镉 <汞 <铅 <锰 <铬 <铜 <锌 ;在糙米中检出的重金属铜和铬的含量与土壤中铜和铬的含量呈显著性相关关系 ,铅、锌、锰的含量与土壤中铅、锌、锰的含量相关关系不显著     

示波极谱法同时测定大气中痕量铅、镉

目前大气飘尘中痕量金属的分析多采用原子吸收法,但因仪器昂贵限制了它的推广应用。为了找到一个较好的方法,本文研究了文献介绍的极谱测镉法,提出了以0.5％KI～0.8％C_8H_8O_3～0.04％(C_2H_5)_4NI—1.0％C_6H_8O_6为底液测定大气中痕量铅、镉的新方法。方法灵敏度:铅0.04PPm、镉0.005PPm。试剂空白低。线性范围:铅0.04～1.5微克/毫升、镉0.005～1.0微克/毫升。样品测定的相对偏差:铅、镉都小于6％。现场测定结果与阳极伏安法比较无显著差异。     

石墨炉原子吸收光谱法测定大气降水中镉镍铅

采用石墨炉原子吸收光谱法测定大气降水中镉、镍、铅，优化了试验条件。镉在0ug／L-5．00ug／L范围、镍和铅在0ug／L-20．0ug／L范围内线性良好，镉、镍、铅的检出限分别为0．03ug／L、0．79ug／L、1．37ug／L，大气降水样品测定的RSD为0．8％-2．6％，加标回收率为96．0％-106％。     

APDC-MIBK萃取火焰原子吸收分光光度法测定生活垃圾堆肥产品中铅、镉的研究

通过试验研究,建立了硝酸-氢氟酸-高氯酸消解、APDC-MIBK萃取火焰原子吸收分光光度法测定生活垃圾堆肥产品中的铅、镉.该方法铅的检出限为2mg/kg,镉的检出限为0.2mg/kg(按称取0.5g试样消解定容至50ml计算),用于不同地域堆肥样品测定,铅、镉的相对标准偏差(RsD)分别为2.29%～8.16%和5.17%～11.7%,加标回收率介于86.8%～107.2%和88.0%～108.0%之间.     

密闭微波消解 ICP- AES 法测定大气颗粒物中金属元素

采用过氯乙烯滤膜采集、密闭微波消解、电感耦合等离子发射光谱法测定大气颗粒物中铅、镍、铬、铜、铁、锌、锰、钡、镉,优化了试验条件.方法线性良好,各元素的检出限在0.001 mg/L～0.01 mg/L之间,滤膜样品测定的RSD为0.6%～2.9%,加标回收率为96.0%～105%.     

非全量消解-悬浮液进样火焰原子吸收光谱法测定煤灰中的铜和铅

试验了用非全量消解—悬浮液直接进样火焰原子吸收光谱法测定煤灰中的铜和铅，结果表明：铜和铅的方法检出限(3σ)分别为0．038mg／L和0．23mg／L，测定吸光度与其浓度的线性范围均为0．5mg／L—5．0mg／L，样品加标回收率在87％—97％之间，相对标准差(n＝4)小于7％。     

共沉富集——单缝石英管火焰原子吸收法测定水中痕量铜,铅,锌,镉

采用共沉富集与单缝石英管技术，以火焰法测定地面水，地下水中的痕量铜，铅，锌，镉，检测限分别为０．５，１．８，０．２，０．１μｇ／Ｌ，四种痕量元素１１次测定的变异系数分别为２．８％，２．３％，３．１％和３．９％。     

用活化沸石处理含铅废水的试验研究

对用活化沸石处理含铅废水进行了试验研究。探讨了活化沸石用量、废水酸度、接触时间等因素对除铅效果的影响。结果表明,在废水ｐＨ４～１２、Ｐｂ２＋０～１００ｍｇ／Ｌ范围内,按铅／活化沸石重量比为１／２００投加活化沸石进行处理,铅去除率大于９８％。     

上海浦东新区环境空气重金属污染特征及来源解析

于2012年3月—2013年2月在浦东新区城区点和郊区点采集TSP样品,利用双酸消解原子荧光法、ICP法分析了样品中的13种元素。结果表明,除As略超标外其他元素均达标,城区点和郊区点环境空气重金属年均值排在前3位的元素是:Fe、Sn、Zn,占样品金属总量的83%~87%;排在末4位的元素是:Ni、Cr、As、Cd,占金属总量的1%~2%。通过EPA PMF 5.0模型运算结果,在城区中6个因子贡献比最高的31.5%为Sn+Fe+Mn,贡献比最低的2.1%为Hg;在郊区中6个因子贡献比最高的36.4%为Pb+Cu,贡献比最低的9.2%为Fe+Sn+Mn。浦东新区富集因子E≤10的元素有Cr、V、Ba、Mn、Ni、Fe、Hg城、Cu郊、As;富集因子E10的元素有Hg郊、Cu城、Zn、Pb、Cd、Sn。     

抚顺市PM10中元素分布特征及来源分析

为了确定抚顺市PM10中元素的浓度特征及其来源,于2006—2007年的采暖季、风沙季和非采暖季在抚顺市的6个采样点采集PM10样品,并用等离子体原子发射光谱法(ICP-AES)测定样品中Ti、Al、Mn、Mg、Ca、Na、K、Cu、Zn、As、Pb、Cr、Ni、Co、Cd、Fe、V等17种元素的含量。结果表明,Al、Mg、Ca、Na、K、Mn、Fe等地壳元素在17种元素中占有较大比重,全年平均达到97.0%。富集因子分析结果表明,Cu、Zn、Pb、Cr、Co、Cd等元素在各季和各采样点明显受到人为活动影响,是典型的污染元素。主因子分析结果显示,土壤风沙尘、建筑尘、燃煤尘、道路扬尘、机动车尾气排放、金属冶炼、锰、铜、钛工业源是抚顺市PM10中元素的主要来源。     

PM source apportionment and trace metallic aerosol affinities during atmospheric pollution episodes: a case study from Puertollano, Spain

Source apportionment study was performed, applying principal component analysis to the results of 221 chemical analyses of PM10 and PM2.5 samples collected daily from the industrial (but low traffic) Spanish town of Puertollano over a 14-month period during 2004-2005. Results reveal compositional variations attributable to different mixtures of natural and anthropogenic materials, mainly soil and rock dust (crustal), marine salt (only in PM10), petrochemical refinery emissions, and particles attributed to the combustion of local coal, which is unusually rich in Pb and Sb. During the study period there were 34 pollution episodes when PM10 exceeded 50 tg m(-3), mostly due to winter air temperature inversions, regional atmospheric stagnation, or African dust incursions (North African, NAF days: usually in summer). Whereas the crustal component during NAF episodes averaged 52% with a PM2.5/PM10 ratio of 0.54, this dropped to 29% and a PM2.5/PM10 of 0.67 during non-NAF days when anthropogenic materials predominated. Abnormally enhanced concentrations of pathfinder metallic trace elements provide additional evidence for source apportionment: thus aerosols with raised levels of Pb and Sb are associated with local coal combustion, Ni and V can be linked to petrochemical PM emissions, and Ti, Mn, Rb, and Ce are particularly characteristic of crustal dust incursions.     

Assessment of metal pollution in urban road dusts from selected highways of the Greater Toronto Area in Canada

Over the last several decades, there has been increased attention on the heavy metal contamination associated with highways because of the associated health hazards and risks. Here, the results are reported of an analysis of the content of metals in roadside dust samples of selected major highways in the Greater Toronto Area of Ontario, Canada. The metals analysed are lead (Pb), zinc (Zn), cadmium (Cd), nickel (Ni), chromium (Cr), copper (Cu), manganese (Mn), calcium (Ca), potassium (K), magnesium (Mg) and iron (Fe). In the samples collected, the recorded mean concentrations (in parts per million) are as follows: Cd (0.51), Cu (162), Fe (40,052), Cr (197.9), K (9647.6), Mg (577.4), Ca (102,349), Zn (200.3), Mn (1202.2), Pb (182.8) and Ni (58.8). The mean concentrations for the analysed samples in the study area are almost all higher than the average natural background values for the corresponding metals. The geo-accumulation index of these metals in the roadside dust under study indicates that they are not contaminated with Cr, Mn and Ca; moderately contaminate with Cd and K; strongly contaminated with Fe and Mg; strongly to extremely contaminated with Ni and Pb; and extremely contaminated with Cu and Zn. The pollution load index (PLI) is used to relate pollution to highway conditions, and the results show that PLI values are slightly low at different samples collected from Highways 401 and 404 and high in many samples collected from Highway 400 and the Don Valley Parkway. Highway 400 exhibits the highest PLI values.     

Characterization of particulate matter and its related metal toxicity in an urban location in South West India

This study reports the quantification of the toxicity of particulate matter (PM)-bound metals and their possible associated risks to human health. For assessment of PM, 24-h samples of PM₁₀ and PM_2.5 were collected by Mini Vol-TAS sampler at an urban site of Pune. Samples were sequentially extracted with ultrapure water and concentrated HNO₃ and analyzed for “soluble” and “total” metals. Factor analysis identified the resuspension of road dust due to traffic, biomass burning, construction activities, and wind-blown dust as possible sources that played an important role for overall pollution throughout the year. Water-soluble proportion was found to be ≤20 % for Cr, Co, Fe, and Al; ≥50 % for Sr, Cd, Ca, and Zn; and a substantial proportion (～25–45 %) for Mn, Ba, K, Na, Ni, Mg, Cu, and Pb metals in PM₁₀. For PM_2.5, the water-soluble proportion was ≤20 % for Fe, Co, Ni, Cr, and Al, while Sr, K, and Cd were mostly soluble (>50 %) and Cu, Ba, Mn, Ca, Zn, Pb, Na, and Mg were substantially soluble (～25–45 %). In the present study, among the toxic metals, Cd and Pb show higher concentration in the soluble fraction and thus represent the higher bioavailability index and especially are harmful to the environment and exposed person. Risk calculations with a simple exposure assessment method showed that the cancer risks of the bioavailable fractions of Cr, Cd and Ni were greater than the standard goal.     

Heavy Metals Content in N. OleanderLeaves As Urban Pollution Assessment

Nerium oleanderL. (Oleander) leaves grown in Palermo city (Sicily, Italy) were collected from six sampling sites representing either areas of high traff{i}c and urbanisation density or areas far away from traffic (e.g. city gardens). Concentration of Al, Ba, Cr, Cu, Fe, Pb, Mg, Mn, and Zn were determined in leaf samples during two years. Multivariate analysis classified the sampling sites in four groups based on the metal content in vegetal leaves in agreement with traffic and human activity site. Many elements studied (Al, Ba, Fe, Mn Mg) arise from the soil composition and others such as Cr, Cu, Pb and Zn as pollutant of the soil. On the other hand, about 30% of Al, Fe Cr, Cu and Pb originate from aerial deposition on leaves. Although the results presented should be handled with caution N. oleandercan be considered as a means of assessing dust contamination in the urban environment.     

Risk assessment of heavy metals in road and soil dusts within PM2.5, PM10 and PM100 fractions in Dongying city, Shandong Province, China

15 road and 14 soil dust samples were collected from an oilfield city, Dongying, from 11/2009-4/2010 and analyzed by inductively coupled plasma-mass spectroscopy (ICP-MS) for V, Cr, Mn, Co, Ni, Cu, Zn, As, Cd and Pb within PM(2.5), PM(10) and PM(100) fractions synchronously. Metal concentrations, sources and human health risk were studied. Results showed that both soil and road dust exhibited higher values for Mn and Zn and lower values for Co and Cd for the three fractions. Mass concentration ratios of PM(2.5)/PM(10) and PM(10)/PM(100) for metals in road and soil dust indicate that most of the heavy metals tend to concentrate in fine particles. Geoaccumulation index and enrichment factors analysis showed that Cu, Zn and Cd exhibited moderate or heavy contamination and significant enrichment, indicating the influence of anthropogenic sources. Vanadium, Cr, Mn and Co were mostly not enriched and were mainly influenced by crustal sources. For Ni, As and Pb, they ranged from not enriched to moderately enriched and were influenced by both crustal materials and anthropogenic sources. The conclusions were confirmed by multivariate analysis methods. Principle component analysis revealed that the major sources were vehicle emission, industrial activities, coal combustion, agricultural activities and crustal materials. The risk assessment results indicated that metal ingestion appeared to be the main exposure route followed by dermal contact. The most likely cause for cancer and other health risks are both the fine particles of soil and road dusts.     

Comparison of three sequential extraction procedures for partitioning of heavy metals in car park dusts

The aim of this study was to elucidate the amount of metal released at each step by using different extractants in three sequential extraction schemes for the partitioning of metal contents of car park deposited dust samples. For this purpose, three different sequential extraction procedures (SEP) were employed for the metal fractionation in car park dust samples collected from the campus of Erciyes University, Kayseri, Turkey. While two of the sequential extraction procedures contain five steps the other, namely the BCR sequential extraction scheme, has three steps. The first two methods fractionate metals to be exchangeable, bound to carbonates, bound to Mn oxides, bound to Fe oxides and bound to organic matter, and the BCR protocol fractionates the metals as acid soluble and exchangeable, reducible, and oxidisable. Determination of the metals Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb and Zn was performed by flame atomic absorption spectrometry (FAAS). The results obtained by the three methods were compared and showed that the amount of metal released at each step of the leaching procedure depended both on the type of reagents used and the sequence in which they were applied. The most mobile elements were Cd, Pb and Zn which are metals potentially toxic to the environment and are also known to originate from traffic. The calculated enrichment factors for Cd and Pb were substantially high (73.5-187 and 18.4-27.5, respectively) and somewhat lower for Zn (5.1-6.8). These results confirm that they are important metal pollutants for car parks. Detection limits and recoveries were found in the range of 0.01-1.39 microg ml(-1) and 68-126%, respectively, for the metals studied and the three sequential extraction procedures.     

太原市大气颗粒物中重金属的污染特征及来源解析

为了解太原市采暖期大气颗粒物不同粒径中重金属的污染特征及其来源,于2012年10月—2013年2月对环境空气中颗粒物采样,用原子吸收分光光度法测定样品中Fe、Pb、Cu、Ni、Cr、Cd、Mn、Zn等8种元素的含量。结果表明,太原市采暖期重金属浓度从高到低依次为FePbMnZnCrCuNiCd。重金属Pb、Mn、Zn、Ni、Cd主要富集在PM2.5中;Cr主要富集在PM10中;Cu主要富集在PM5中;Fe主要在粒径大于2.5μm的粗粒子中富集。除Zn外,其他7种元素浓度均表现为灰霾期采暖期采暖前。通过主因子分析表明,太原市大气颗粒物中重金属主要来源于冶金、有机合成工业、燃煤、汽车尾气、土壤尘等。     

Load of Heavy Metals in the Airborne Dust Particulates of an Urban City of Central India

The geographical and temporal distribution patterns of airborne dust particulates have been studied in different representative areas of Raipur City. Dust fall samples from different sites were collected and some selected toxic metals namely Cr, Mn, Fe, Ni, Cu, Zn, Sb and Pb in them were determined by AAS. Total annual flux of 11.7, 541.4, 2751.0, 14.2, 9.8, 90.9, 17.6, and 17.7 kg km(-2) y(-1) were measured for Cr, Mn, Fe, Ni, Cu, Zn, Sb, and Pb respectively. The occurrence of metal concentration were generally in the order industrial > heavy traffic > commercial > residential area in Raipur city. The results of analysis show the existence of toxic metal concentration in the order Fe > Mn > Zn > Pb approximately Sb > Ni > Cr > Cu in Raipur city. These large levels of metal pollutants have also been correlated with some meteorological parameters like temperature, relative humidity and wind velocity, and strong positive correlations have been observed.