烟囱与吸收塔合一结构分析

通过手工计算和ANSYS有限元软件计算两种方法对安徽新源热电有限公司烟囱与吸收塔合一结构进行结构计算。分析了结构在风载荷、地震载荷作用下的应力和变形,比较了手工计算和有限元电算结果,可为类似工程的计算提供理论参考。     

氨法脱硫工艺物料平衡模型的研究

建立了氨法脱硫工艺的物料衡算模型,描述了物料计算软件的计算框图和开发过程,介绍了计算模型在实际脱硫工程中的应用,表明该模型对工程设计和设备选型具有一定的指导意义。     

AHP法在废水治理工程评价中的应用

应用层次分析法（ＡＨＰ）的原理，建立了废水处理工程的评价模型，并结合废水处理的实例进行了研究，结果证明了ＡＨＰ法是评价废水处理工程的有效方法。     

居民区地下配电房通风降噪仿真与分析

为了合理控制居民区地下配电房的室内温度，降低机械通风带来的环境噪声，建立了配电房风速场的仿真模型并对其进行分析计算。以佛山鸿翔小区一个位于某住宅楼地下的配电房为例，使用ANSYS13.0软件对其中主要热源———变压器周围的风速场进行仿真分析。结果表明：在保证室内电气设备工作温度的前提下，优化计算通风量，通过电缆沟辅助进行机械排风，使电房噪声由之前的平均79dB( A)降低到71dB( A)。通过修改模型中的相关参数，可用于其它地下配电房温度场的模拟与预测，为设计提供前期参考。     

脱硫离心喷嘴雾化特性的研究

根据动量守恒原理，分析了脱硫离心喷嘴的结构参数与喷嘴雾化特性(流量系数、喷雾角等)之间的关系。建立了相应的无粘理论计算模型。将理论计算结果与实验数据进行比较，表明该无粘理论计算模型对脱硫喷嘴雾化特性的研究具有一定的参考价值。     

环境治理工程评标的双基点模型及应用

动用多指标综合排序的双基点法，建立了环境治理工程评标的数学模型。应用实例表明，该模型可以为环境治理工程评标提供客观、合理的方法。     

尿素法ADC发泡剂清洁生产评价指标体系

采用层次分析法建立了由总到分的递阶层次结构模型评价指标体系,以ADC发泡剂(偶氮二甲酰胺)生产先进企业的数据为基础,确定了各指标的基准值及权重,建立了ADC发泡剂清洁生产评价体系,介绍了定量评价指标和定性评价指标的考核评分计算方法以及企业清洁生产综合评价指数的计算方法.     

上海市生活垃圾处置计划量指标测算模型初探

对生活垃圾处置计划管理政策的意义、生活垃圾处置计划指标测算模型建立的意义和作用进行分析,对建立模型的因素、计算公式、计算流程等进行详细说明,并对3个典型区县的实际情况进行了计算和分析,总结了模型存在的问题和完善方向。     

多介质逸度模型的应用与展望

介绍了源于逸度算法的多介质逸度模型。该模型具有结构简单、所需参数少、容易计算、结果表示直观、其计算方法可推广到任意数目的环境介质、预测结果对环境监测和管理具有指导意义等优点。综述了逸度模型的理论基础及近10年的发展与应用情况,并展望了多介质逸度模型的应用前景和发展趋势。     

基于参数化模型优化的喷氨格栅设计方法研究

从喷氨格栅工程设计要求出发,结合数值模拟分析、代理模型技术以及优化设计方法,提出了一套基于参数化模型优化的喷氨格栅设计方法和流程。该方法从工程设计要求的分析入手,根据喷氨格栅几何参数对喷氨特性的影响特点和规律,建立参数化设计数学模型,并通过优化计算最终获得喷氨格栅的最优设计。另外,通过实例计算验证了该设计方法在SCR脱硝系统喷氨格栅设计中的适用性。     

基于ANSYS的脱硫烟道结构有限元分析

利用ANSYS有限元数值分析软件,对章丘电厂二期烟气脱硫系统烟道结构进行3D数值计算,考察烟道结构受力和变形情况,从而对加固肋和内撑杆规格进行设计选型.结果表明,有限元分析方法对于脱硫系统结构的精准设计具有一定的指导意义.     

国内废钢行业概况及废钢价格关联因素的量化研究

介绍了"十五"和"十一五"时期国内废钢行业发展概况,重点阐述废钢行业的回收供应以及消耗情况,并对影响废钢价格的因素进行数学建模,对关联程度大小进行量化,对更好地分析废钢市场走势有较好的指导意义。     

LCA comparison of container systems in municipal solid waste management

The planning and design of integrated municipal solid waste management (MSWM) systems requires accurate environmental impact evaluation of the systems and their components. This research assessed, quantified and compared the environmental impact of the first stage of the most used MSW container systems. The comparison was based on factors such as the volume of the containers, from small bins of 60–80 l to containers of 2400 l, and on the manufactured materials, steel and high-density polyethylene (HDPE). Also, some parameters such as frequency of collections, waste generation, filling percentage and waste container contents, were established to obtain comparable systems. The methodological framework of the analysis was the life cycle assessment (LCA), and the impact assessment method was based on CML 2 baseline 2000. Results indicated that, for the same volume, the collection systems that use HDPE waste containers had more of an impact than those using steel waste containers, in terms of abiotic depletion, global warming, ozone layer depletion, acidification, eutrophication, photochemical oxidation, human toxicity and terrestrial ecotoxicity. Besides, the collection systems using small HDPE bins (60 l or 80 l) had most impact while systems using big steel containers (2400 l) had less impact. Subsequent sensitivity analysis about the parameters established demonstrated that they could change the ultimate environmental impact of each waste container collection system, but that the comparative relationship between systems was similar.     

Evaluation of environmental feasibility of steel pipe sheet pile cutoff wall at coastal landfill sites

An evaluation method that can express the local leakage of leachate from joint sections in steel pipe sheet pile (SPSP) cutoff walls is discussed in this study. In particular, the evaluation of environmental feasibility (containment of leachates containing toxic substances) considering a three-dimensional arrangement and hydraulic conductivity distribution of the joint sections in the SPSP cutoff wall is compared with an evaluation that uses the equivalent hydraulic conductivity. This equivalent hydraulic conductivity assumes that the joint section and the steel pipe are integrated; therefore, the hydraulic conductivity is substituted with a uniform permeable layer. However, in an evaluation that employs the equivalent hydraulic conductivity, it is difficult to consider the local leakage of leachate containing toxic substances from the joint sections in the SPSP cutoff wall. It was established that evaluations of the environmental feasibility of SPSP cutoff walls with joint sections must take into account the local leakage of leachates containing toxic substances from the joint sections. Also, it was clarified that technologies that lower the hydraulic conductivities of joint sections in SPSP cutoff walls and also facilitate the use of sparser joint arrangements contribute significantly to increasing the environmental feasibility of SPSP cutoff walls at landfill sites.     

Sustainable disposal of municipal solid waste: Post bioreactor landfill polishing

Sustainable disposal of municipal solid waste (MSW) requires assurance that contaminant release will be minimized or prevented within a reasonable time frame before the landfill is abandoned so that the risk of contamination release is not passed to future generations. This could be accomplished through waste acceptance criteria such as those established by the European Union (EU) that prohibit land disposal of untreated organic matter. In the EU, mechanical, biological and/or thermal pretreatment of MSW is therefore necessary prior to landfilling which is complicated and costly. In other parts of the world, treatment within highly engineered landfills is under development, known as bioreactor landfills. However, the completed bioreactor landfill still contains material, largely nonbiodegradable carbon and ammonia that may be released to the environment over the long-term. This paper provides a conceptual analysis of an approach to ensure landfill sustainability by the rapid removal of these remaining materials, leachate treatment and recirculation combined with aeration. The analysis in this paper includes a preliminary experimental evaluation using real mature leachate and waste samples, a modeling effort using a simplified mass balance approach and input parameters from real typical bioreactor cases, and a cost estimate for the suggested treatment method.     

Systematically selecting an alternative to remediate soil contaminating groundwater

Contaminated soil is a continuing source of ground water contamination at some hazardous waste sites. Even if that soil does not pose a threat to human health or the environment, soil remediation may benefit ground-water cleanup in terms of time, money, or protectiveness. A method has been developed to provide a systematic manner to select a soil cleanup alternative. Using commercially available Windows-based software, the method consists of the development of a decision tree whose chance nodes are the restoration time frame probability distributions. Uncertainty associated with site data is quantitatively evaluated using Monte Carlo analysis to develop the probability distributions. The decision tree selects the alternative with the lowest cost. Data from an actual remedial investigation/feasibility study demonstrate the ease and practicality of the selection method.     

Analysis of a system for remote, dry removal of solidified mixed waste

This paper describes a novel technology for the removal of solidified radioactive waste from underground storage tanks at the DOE Hanford site in southeast Washington. The process involves the use of a unique high pressure system which pulverizes the hardened saltcake with stainless steel pellets to a powder for easy vacuum removal. The steel pellets can be magnetically separated from the waste material for re-use. Specifically this study analyzes the effects of various steel abrasives, pressure of the air stream, and stand-off distance on removal rates and penetration depth on simulated saltcake samples using the high pressure technique. A full-scale test set-up and protocol were implemented to allow for comprehensive testing. To insure reproducibility of the method, tests were then run for the optimum removal parameters. A time-dependent test was also conducted to determine the relationship of removal rates to length of pressure blasts. The results of these tests revealed that stand-off distance and pressure could be positively correlated to removal volumes. Additionally, a statistical analysis confirmed that nozzle angle is independent of removal rate. This study demonstrated that the pellet ‘blaster’ technique is a safe, effective method for removal of radioactive wastes without any increase in either waste mass or volume.     

单极性三维电极电解处理含钴废水

采用并联式单极性三维电极电解处理低浓度含钴废水并回收金属钴，比较了二维电极与三维电极的钴离子去除效果，探讨了填充材料、电流、填充比（填充材料与废水的质量比）、废水pH对钴离子去除效果的影响，建立了反应动力学模型，并进行了经济性分析。实验结果表明：三维电极对钴离子的去除效果远优于二维电极;在以网状Ti/RuO₂为阳极、不锈钢板为阴极并作为主电极、空心钢球为第三极、极间距5 cm、电解时间60 min、电流为0.6 A、填充比为2.5、不调节废水pH的条件下处理钴离子质量浓度为112.3 mg/L的废水，钴离子去除率可达85.6%、电流效率为68.3%;去除钴离子的电化学反应符合一级反应动力学模型;该方法具有良好的环境与经济效益。     

Fast-track remediation for redevelopment of a former integrated steel mill site

Remedial action was initiated and completed on an approximately 500-acre brownfield site in southern California within a period of five months during the summer of 1995. Remedial actions included design and construction of an approximately 14-acre cap, including a synthetic membrane; design, construction, and testing of an in-situ soil vapor extraction system; excavation, on-site treatment, and off-site disposal of approximately 7,000 cubic yards of residual waste and affected soil; and verification sampling, analysis, and health risk screening in 20 units of a former integrated steel mill. Completion of remedial action on this portion of the mill site within this time frame was required due to site redevelopment plans which included construction of an auto raceway with scheduled races in early 1997. Rapid remedial action was possible only through simultaneous completion of multiple remediation tasks. This could be done only with continuous communication and close coordination among the site owner, lead regulatory agency, and contractors.