首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 390 毫秒
1.
多核复合聚铝絮凝剂对水体残留铝的影响   总被引:2,自引:2,他引:0  
采用分别添加金属离子Fe~(3+)和Zn~(2+)的方法制备多核复合型絮凝剂聚合氯化铝铁(PAFC)和聚合氯化铝锌(PAZC),并与市售聚合氯化铝(PAC)比较处理高岭土模拟水样后出水残留铝浓度,得出复合絮凝剂具有更低的出水余铝量及更宽的pH适用范围以及更低的投加量。达到85%COD去除率,PAZC、PAFC和PAC用量分别为5、10和20 mg/L;处理后出水残余铝量分别为0.04、0.09和0.14 mg/L;处理成本分别为0.020、0.028和0.048元/t。  相似文献   

2.
制备了聚硅酸氯化铝(PASC)絮凝剂,并用其进行了皂素废水处理实验。考察了絮凝剂投加量、pH值、搅拌速度对COD和浊度去除率的影响。结果表明,当絮凝剂投加量为9~13.5 mg/L、pH值5~7、搅拌速度150~250 r/min时,COD和浊度去除效果较好。最佳工艺条件为:絮凝剂投加量11.25 mg/L、pH值6、搅拌速度200 r/min。此时,COD去除率为93.7%,浊度去除率为97.5%。PASC的絮凝性能明显优于PAC。  相似文献   

3.
在室温条件下,分别选用聚合氯化铝(PAC)、聚合氯化铝铁(PAFC)及三氯化铁(FeCl3)对玉米深加工废水进行混凝实验。综合考虑各种混凝剂对磷、COD以及SS的去除效果,最终选取PAC作为混凝剂。采用PAC和聚丙烯酰胺(PAM)作为复合混凝剂,对其去除效果做进一步研究,并确定了最佳投加量及pH值。实验结果表明,在PAC投加量25mg/L,PAM投加量0.5 mg/L,pH为8条件下,混凝效果最佳。磷、COD、SS去除率可分别达到90.1%、53.3%和88.2%,对应的出水质量浓度分别为0.41、26.8和2 mg/L。  相似文献   

4.
针对水厂低浊高藻水的处理难题,研究了改性凹凸棒土(改性凹土)联合聚合氯化铝(PAC)强化混凝的除藻除浊效果。设计实验原水条件为叶绿素a(chl-a)浓度为98.58~110.35μg/L,浊度(5.6±0.5)NTU。考察了PAC和改性凹土的复配投加量、混凝沉淀时间、pH、投加顺序、搅拌速率等工艺参数对Chl-a和浊度耦合去除效果的影响。结果表明,"PAC+改性凹土"对Chl-a和浊度的去除效果明显优于单投PAC的效果。当PAC投药量12 mg/L,改性凹土投药量10 mg/L,沉淀时间20 min时,对Chl-a和浊度的去除率可分别达到92.5%和89.2%,可至少减少40%的PAC投量,且形成的矾花密实,沉降速度快,去除效率高。最适pH范围为7~8。投加顺序应为先投加改性凹土,混合搅拌转数宜慢速,可控制为50 r/min。  相似文献   

5.
采用响应面分析法对聚合氯化铝(PAC)与污泥生产的微生物絮凝剂复配处理涂料废水的过程进行了优化,设定的响应值为COD和色度去除率。实验分别拟合了关于COD去除率和色度去除率的二次模型,根据响应值的分布情况,确定涂料废水的最佳絮凝条件为微生物絮凝剂浓度47 mg/L,PAC浓度39 mg/L,pH为8.2,CaCl2浓度0.38 g/L,搅拌速度210 r/min。最佳絮凝条件下,微生物絮凝剂对涂料废水中COD和色度的去除率分别达到77.6%和68.9%。  相似文献   

6.
聚合氯化铝与粉末活性炭联合强化混凝处理垃圾渗滤液   总被引:1,自引:0,他引:1  
研究了联合粉末活性炭与聚合氯化铝(PAC)强化混凝对垃圾渗滤液原水的处理效果。结果表明,在原水COD为4 100 mg/L、浊度为147 NTU、UV254为20的条件下,粉末活性炭的加入可以有效增加垃圾渗滤液中有机物的去除率,PAC投加量为0.6 g/L时,投加0.6 g/L粉末活性炭,COD的去除率由21.6%提高到29.1%,UV254去除率由29.8%提高到39.9%,剩余浊度由138 NTU降到133 NTU。该强化混凝过程使原水中溶解性小分子有机物的去除率提高显著,PAC投加量为0.6 g/L时,投加0.6 g/L粉末活性炭,在分子量小于1 kDa的范围内,UV254去除率由2.9%上升为10%。  相似文献   

7.
新型聚合铝硅混凝剂处理洗浴废水的试验研究   总被引:1,自引:0,他引:1  
针对常规铝盐、铁盐去除洗浴废水中阴离子洗涤剂 (LAS)效果不理想的状况 ,采用高碱化度钙型聚合铝硅混凝剂 (CPASC)进行了试验研究 ,同时与聚合氯化铝 (PAC)作了比较。结果表明 ,该混凝剂对洗浴废水中COD、LAS、SS及浊度都有较高的去除率 ,特别对LAS、COD的去除率分别比PAC高 10 %和 8%以上。当投加量为 6 0mg/L时 ,出水各项指标均达到生活杂用水水质标准 (GJ2 5 .1 89)。  相似文献   

8.
使用自制的酸改性蒙脱石絮凝剂(MTSF)对高浓度畜禽养殖废水进行处理,以传统絮凝剂聚合氯化铝(PAC)作为参考,研究了絮凝剂投加量对废水处理絮凝效果的影响,探讨絮凝过程中絮体沉降特性。结果表明,MTSF对养殖废水的絮凝效果优于PAC,在最佳投加量12 000mg/L时,浊度、SS、COD、氨氮及TP的去除率分别达到85.7%、96.8%、60.7%、16.3%和97.7%;MTSF投加量虽远大于PAC,但MTSF的絮体沉降体积只占整个体积的12.0%,不到PAC絮体沉降体积的1/5,MTSF中的可溶态物质和颗粒态物质的相互协同效应加快了絮凝过程和沉降过程;MTSF处理后上清液中Cd、Cr、Ni、Cu、Pb均未检出,而As小于《污水综合排放标准》(GB 8978—2002)中最高允许排放质量浓度(0.5mg/L)。  相似文献   

9.
探讨了微生物絮凝剂处理二级出水过程中投加量和pH值对溶解性有机碳和浊度处理效果的影响,及将微生物絮凝剂与聚合氯化铝按不同比例复配后的去除效果及pH值对最佳投药量下去除效果的影响。并使用三维荧光光谱(3DEEM)分析了不同种类的絮凝剂在去除水中溶解性有机物(DOM)时的差别。实验结果表明:微生物絮凝剂的最佳投药量为20 mg·L~(-1),最适pH值为7.5,此时TOC去除率为17%,浊度去除率为45%。最佳复配投药量为微生物絮凝剂10mg·L~(-1)聚合氯化铝20 mg·L~(-1),最适pH值为7,此时TOC去除率为33%,浊度去除率为51%。复配使用对腐殖质有很好的去除效果。  相似文献   

10.
为了处理水性漆洗涤废水,对絮凝沉淀处理水性漆洗涤废水进行了研究。分别以硫酸铝(AS)、聚合氯化铝(PAC)、聚合氯化铝(PAFC)和聚合硫酸铁(PFS)4种无机絮凝剂为絮凝剂,考察了不同絮凝剂投加量、搅拌策略和时间以及沉降时间等因素对水性漆洗漆废水COD的去除率和剩余浊度的影响。为了研究几种絮凝剂对水性漆洗涤废水的絮凝机理,对废水和絮凝剂进行了Zeta电位分析。结合废水处理的成本和处理效率,确定了优化处理方案:最终选定PAFC作为絮凝剂,投加量为138 g·t~(-1),快速搅拌1 min,慢速搅拌1.5 min和沉淀60 min。  相似文献   

11.
A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO2 removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion  相似文献   

12.
This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).  相似文献   

13.
14.
介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠  相似文献   

15.
在实施ISO/IEC 17025:1999标准《检测和校准实验室能力的通用要求》过程中,通过实验室质量管理体系内部审核的实践与系统分析,识别出内部审核策划阶段的关键环节,提出审核范围确定、审核计划和抽样方案制订的质量控制要求,为有序高效地实施内部审核提供了技术方法。  相似文献   

16.
The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.  相似文献   

17.
Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.  相似文献   

18.
结合扬中生态环境的基本情况和存在的不足,进行了具体分析,对扬中未来生态建设的发展方向提出了建议及实施措施。  相似文献   

19.

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO2 coatings included in this investigation ranged from thin commercially available coatings (ActivTM and BioCleanTM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.  相似文献   

20.
Bhattacharya A  Sarkar SK 《Ambio》2003,32(1):70-75
India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号