Quantitative assessment of the toxic effects of heavy metals on 1,2-dichloroethane biodegradation in co-contaminated soil under aerobic condition

1,2-Dichloroethane (1,2-DCA) is one of the most hazardous pollutant of soil and groundwater, and is produced in excess of 5.44 × 10⁹ kg annually. Owing to their toxicity, persistence and potential for bioaccumulation, there is a growing interest in technologies for their removal. Heavy metals are known to be toxic to soil microorganisms at high concentrations and can hinder the biodegradation of organic contaminants. In this study, the inhibitory effect of heavy metals, namely; arsenic, cadmium, mercury and lead, on the aerobic biodegradation of 1,2-DCA by autochthonous microorganisms was evaluated in soil microcosm setting. The presence of heavy metals was observed to have a negative impact on the biodegradation of 1,2-DCA in both soil samples tested, with the toxic effect being more pronounced in loam soil, than in clay soil. Generally, 75 ppm As³⁺, 840 ppm Hg²⁺, and 420 ppm Pb²⁺ resulted in 34.24%, 40.64%, and 45.94% increase in the half live (t_½) of 1,2-DCA, respectively, in loam soil, while concentrations above 127.5 ppm Cd²⁺, 840 ppm Hg²⁺ and 420 ppm of Pb²⁺ and less than 75 ppm As³⁺ was required to cause a >10% increase in the t_½ of 1,2-DCA in clay soil. A dose-dependent relationship between degradation rate constant (k₁) of 1,2-DCA and metal ion concentrations was observed for all the heavy metals tested, except for Hg²⁺. This study demonstrated that different heavy metals have different impacts on the degree of 1,2-DCA degradation. Results also suggest that the degree of inhibition is metal specific and is also dependent on several factors including; soil type, pH, moisture content and available nutrients.     

Oxidation of bisphenol F (BPF) by manganese dioxide

Bisphenol F (BPF), an environmental estrogen, is used as a monomer in plastic industry and its environmental fate and decontamination are emerging concern. This study focused on the kinetics, influencing factors and pathways of its oxidation by MnO₂. At pH 5.5, about 90% of BPF was oxidized in 20 min in a solution containing 100 μM MnO₂ and 4.4 μM BPF. The reaction was pH-dependent, following an order of pH 4.5 > pH 5.5 > pH 8.6 > pH 7.5 > pH 6.5 > pH 9.6. Humic acids inhibited the reaction at low (≤pH 5.5) and high pH (≥pH 8.6) at high concentrations. In addition, metal ions and anions also suppressed the reaction, following the order Mn²⁺ > Ca²⁺ > Mg²⁺ > Na⁺ and HPO₄²⁻ > Cl⁻ > NO₃⁻ ≈ SO₄²⁻, respectively. A total of 5 products were identified, from which a tentative pathway was proposed.     

Enhancing p-cresol extraction from soil

Soil washing is a potential technology for rapid removal of organic hydrocarbons sorbed to soils. In this work, p-cresol desorption with different non-ionic surfactants (Tween 80, Brij 30 and Triton X-100) was compared to cyclodextrine and citrate as solubilizer. A series of batch extraction experiments were conducted at 20 °C using the field soil with different extracting solutions at various concentrations to investigate the removal efficiency and to optimize the concentration of the extractant. The use of the different extracting agents was very selective to p-cresol extraction, minimizing soil organic matter releasing and maintaining the natural pH of the soil. The highest asymptotic values of desorption percentages were obtained for Tween 80 and Brij 30 at 48 h. However, Brij 30 ecotoxicity (EC₅₀ = 0.5 mg L⁻¹) is in the same order of that obtained for p-cresol, being this surfactant clearly ruled out. Liquid to solid ratio of 2.5 mL g⁻¹ presented the best extraction results, while concentrations higher than 1 g L⁻¹ for Tween 80 and Citrate did not produce any significant effect on the desorption efficiency. p-Cresol extraction efficiencies higher than 70% and 60% for Tween 80 and Citrate, respectively.     

Dissolution of mimetite Pb5(AsO4)3Cl in low-molecular-weight organic acids and EDTA

Due to its relatively low solubility, mimetite Pb₅(AsO₄)₃Cl may control Pb and As(V) solution levels at a low value in contaminated soils. The time-dependent dissolution of mimetite by low-molecular-weight organic acids (LMWOAs) such as acetic, lactic, citric, and ethylene diamine tetra-acetic acid (EDTA) was determined. At pH 3.5, the presence of citric acid or EDTA significantly increases the solubility of mimetite while acetic or lactic acids show little effect. The effect of all organic anions on the dissolution of mimetite increased with the increase in solution pH. The rate of mimetite dissolution depended on the kind and concentration of organic solvents in the sequence r_EDTA > r_lactate > r_acetate > r_citrate. Soluble Pb and As(V) released in LMWOAs and EDTA were higher than the WHO guideline value for these elements in drinking water (10 μg As(V) L⁻¹, 10 μg Pb L⁻¹). This suggests that soil organic acids in rhizosphere can potentially liberate Pb and As(V) from mimetite in contaminated soils.     

Investigation of trace metal binding properties of lignin by diffusive gradients in thin films

The binding behavior of lignin for Pb, Cu, Co, Mn, Cd and Ni was studied using the diffusive gradients in thin films technique (DGT). Samplers with different structures of diffusive gel were used in the well-stirred systems containing known concentrations of metals along with (a) 10, 20 and 40 μM lignin and; (b) 0.64 and 6.47 μM Suwannee river fulvic acid + 40 μM lignin at an ionic strength of 0.01 M (NaNO₃) and pH = 7. Diffusion coefficients of lignin complexes in acrylamide gels were estimated and found to be less than 5% of the equivalent coefficients for the uncomplexed metal ions. These values were used to calculate concentrations of labile metals from DGT measurements in solutions, where lignin could discriminate metals in the order of Pb⁺² > Cu⁺² > Cd⁺² > Ni⁺² > Co⁺² > Mn⁺². Stability constants (Log K) were calculated using Visual MINTEQ II and WHAM V software. The K values were compared with the stability constants from titration of Pb and Cd with 10 μM lignin aqueous samples and with those of humic substances in natural waters. The constants obtained from measurement of complexing capacities might bias the real corresponding values unless two line regression analyses on titration data are considered. The DGT study of fractionation of metal species at varying ratios indicated that the proportion of organic complexes decreased with increasing ratios and gradually more metals were exchanged with inorganic phases. Speciation of Pb and Cd is affected by the concentrations of FA, Cd is dominantly bound with FA while Pb is evenly partitioned between the ligands. The comprehensive knowledge of metal-lignin complexes sheds some light on in situ operational speciation information that can be achieved by DGT.     

Freshwater Ulva (Chlorophyta) as a bioaccumulator of selected heavy metals (Cd, Ni and Pb) and alkaline earth metals (Ca and Mg)

We analyzed the ability of freshwater taxa of the genus Ulva (Ulvaceae, Chlorophyta) to serve as bioindicators of metal in lakes and rivers. Changes in heavy metal (Ni, Cd and Pb) and alkaline earth metal (Ca and Mg) concentrations in freshwater Ulva thalli were investigated during the period from June to August 2010. The study was conducted in two ecosystems in Western Poland, the Malta lake (10 sites) and the Nielba river (six sites). Three components were collected for each sample, including water, sediment and Ulva thalli. The average concentrations of metals in the water sample and in the macroalgae decreased in the following order: Ca > Mg > Ni > Pb > Cd. The sediment revealed a slightly altered order: Ca > Mg > Pb > Ni > Cd. Ca and Mg were found at the highest concentrations in thalli due to the presence of carbonate on its surface. Among the examined heavy metals in thalli, Ni was in the highest concentration, and Cd found in the lowest concentration. There were statistically significant correlations between the levels of metals in macroalgae, water and sediment. Freshwater populations of Ulva exhibited a greater efficiency to bioaccumulate nickel as compared to species derived from marine ecosystems.     

Linking chemical extraction to microbial degradation of 14C-hexadecane in soil

Chemical extractions have been shown to measure the biodegradable fraction of aromatic contaminants in soil; however, there is little research on the chemical prediction of aliphatic hydrocarbon degradation. The aim of this study was to investigate the potential for cyclodextrin extractions to predict hexadecane biodegradation in soil. Soils were amended with 10 or 100 mg kg⁻¹ of a model alkane n-hexadecane and 100 Bq g⁻¹¹⁴C-n-hexadecane. Correlations between the extents of mineralisation and extractions of the ¹⁴C-contaminant were determined. Solvent shake extractions and aqueous CaCl₂ extractions were poor predictors of hexadecane bioaccessibility. However, the novel HP-α-CD shake extraction showed close correlation (r² = 0.90, n = 36, p < 0.05) to the mineralisation data. This novel extraction technique has the potential to be used to assess the biodegradable aliphatic hydrocarbon fraction in contaminated soils.     

Rapid metal extractability tests from polluted mining soils by ultrasound probe sonication and microwave-assisted extraction systems

Ultrasonic probe sonication (UPS) and microwave-assisted extraction (MAE) were used for rapid single extraction of Cd, Cr, Cu, Ni, Pb, and Zn from soils polluted by former mining activities (Mónica Mine, Bustarviejo, NW Madrid, Spain), using 0.01 mol L^?1 calcium chloride (CaCl₂), 0.43 mol L^?1 acetic acid (CH₃COOH), and 0.05 mol L^?1 ethylenediaminetetraacetic acid (EDTA) at pH 7 as extracting agents. The optimum extraction conditions by UPS consisted of an extraction time of 2 min for both CaCl₂ and EDTA extractions and 15 min for CH₃COOH extraction, at 30% ultrasound (US) amplitude, whereas in the case of MAE, they consisted of 5 min at 50 °C for both CaCl₂ and EDTA extractions and 15 min at 120 °C for CH₃COOH extraction. Extractable concentrations were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES). The proposed methods were compared with a reduced version of the corresponding single extraction procedures proposed by the Standards, Measurements and Testing Programme (SM&T). The results obtained showed a great variability on extraction percentages, depending on the metal, the total concentration level and the soil sample, reaching high values in some areas. However, the correlation analysis showed that total concentration is the most relevant factor for element extractability in these soil samples. From the results obtained, the application of the accelerated extraction procedures, such as MAE and UPS, could be considered a useful approach to evaluate rapidly the extractability of the metals studied.     

Removing perfluorooctane sulfonate and perfluorooctanoic acid from solid matrices, paper, fabrics, and sand by mineral acid suppression and supercritical carbon dioxide extraction

The removal of perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) from solid matrices has received considerable attention because of the environmental persistence, bioaccumulation, and potential toxicity of these compounds. This study presents a simple method using concentrated HNO₃ as a suppression agent, and methanol-modified supercritical carbon dioxide (Sc-CO₂) extraction for removing PFOS and PFOA from solid matrices. The optimal conditions were 16 M HNO₃ and 20% (v/v) methanol containing Sc-CO₂, under a pressure of 20.3 MPa and a temperature of 50 °C. Extraction time was set at 70 min (40 min for static and 30 min for dynamic extraction). PFOA and PFOS were identified and quantitated by liquid chromatography/mass spectrometry. The extraction efficiencies (with double extractions) were close to 100% for PFOA and 80% for PFOS for both paper and fabric matrices. The extraction efficiencies for sand were approximately 77% for PFOA and 59% for PFOS. The results show that this method is accurate, and effective, and that it provides a promising and convenient approach to remediate the environment of hazardous PFOA and PFOS contamination.     

Removal of Rhodamine B under visible irradiation in the presence of Fe⁰, H₂O₂, citrate and aeration at circumneutral pH

A new Vis-Fe⁰-H₂O₂-citrate-O₂ system comprising zero-valent iron, hydrogen peroxide, citrate anion and aeration at circumneutral pH under visible irradiation was studied. 21 μmol L⁻¹ of Rhodamine B (RhB) was chosen as the substrate to be tested. Experiments were conducted under conditions of 2.9 mmol L⁻¹ of H₂O₂, 12.6 g of Fe⁰ and 1.0 mmol L⁻¹ of citrate at pH 7.5. Results showed that, in 1 h reaction, 54% of RhB was removed with corresponding 26% of COD reduced. Meanwhile, the amount of released dissolved irons from Fe⁰ surface was found to be at a very low level as <5.4 μmol L⁻¹. Extinguishing tests with isopropanol suggested that RhB oxidation by hydroxyl radicals was the main process taken place in Vis-Fe⁰-H₂O₂-citrate-O₂ system, which accounted for 75% of substrate removal in 3 h reaction. Control and factor influencing experiments showed that the prohibitive extents of individual factor importance on RhB removal followed a decreasing order of Fe⁰ > H₂O₂ > citrate > Vis > O₂. This study showed an excellent system that could remove refractory organic compounds from water in laboratory researches, and also provided a good idea to reduce secondary contamination by dissolved irons in future investigations.     

Metal sorption by peat and algae treated peat: kinetics and factors affecting the process

The article presents a new approach that can be used for the purification of water contaminated by heavy metals. The treatment of peat with microalgae showed to be an effective way of increasing metal uptake by peat. Metal sorption was studied for a multimetal solution containing Cu, Cd, Ni, Zn, Cd, and Pb. Cu and Pb were found to be the metals having the highest affinity to peat. Water hardness has a strong effect on the uptake of borderline metals (Cd, Ni, Zn, Cd) from a solution. The use of algae for peat treatment resulted in less time to reach an equilibrium (24 h vs. 72 h for pure peat), and the effect of water hardness (Ca²⁺) on metal uptake was considerably reduced. Both peat and algal-treated peat were able to take up metals from rather acidic solutions (pH 3.0). pH had less influence on the metal uptake compared with water hardness. The affinity of heavy metals to peat was the following: Pb > Cu > Ni > Cd > Zn > Co. It slightly changed to Pb > Cu > Ni > Cd ≈ Co ≈ Zn when the combined sorbent, peat treated with microalga, was applied.     

Recycling of EDTA solution after soil washing of Pb, Zn, Cd and As contaminated soil

Soil washing with EDTA is known to be an effective means of removing toxic metals from contaminated soil. A practical way of recycling of used soil washing solution remains, however, an unsolved technical problem. We demonstrate here, in a laboratory scale experiment, the feasibility of using acid precipitation to recover up to 50% of EDTA from used soil washing solution obtained after extraction of Pb (5330 mg kg⁻¹), Zn (3400 mg kg⁻¹), Cd (35 mg kg⁻¹) and As (279 mg kg⁻¹) contaminated soil. Up to 100% of EDTA residual in the washing solution and 100%, 97%, 98% and 100% of initial Pb, Zn, Cd and As concentration in the solution, respectively, were removed in an electrolytic cell using a graphite anode. We employed the recovered EDTA and treated washing solution to prepare recycled soil washing solution with the same potential for extracting toxic metals from soil as the original. The efficiency of soil washing depends on the EDTA concentration. Using twice recycled 30 mmol EDTA kg⁻¹ soil, we removed 44%, 20%, 53% and 61% of Pb, Zn, Cd and As, respectively, from contaminated soil.     

Effects of remediation train sequence on decontamination of heavy metal-contaminated soil containing mercury

When a contaminated site contains pollutants including both nonvolatile metals and Hg, one single remediation technology may not satisfactorily remove all contaminants. Therefore, in this study, chemical extraction and thermal treatment were combined as a remediation train to remove heavy metals, including Hg, from contaminated soil. A 0.2 M solution of ethylenediamine tetraacetic acid (EDTA) was shown to be the most effective reagent for extraction of considerable amounts of Cu, Pb, and Zn (>50%). Hg removal was ineffective using 0.2 M EDTA, but thermogravimetric analysis suggested that heating to 550°C with a heating rate of 5°C/min for a duration of 1 hr appeared to be an effective approach for Hg removal. With the employment of thermal treatment, up to 99% of Hg could be removed. However, executing thermal treatment prior to chemical extraction reduced the effectiveness of the subsequent EDTA extraction because nonvolatile heavy metals were immobilized in soil aggregates after the 550°C treatment. The remediation train of chemical extraction followed by thermal treatment appears to remediate soils that have been contaminated by many nonvolatile heavy metals and Hg.

ImplicationsA remediation train conjoining two or more techniques has been initialized to remove multiple metals. Better understandings of the impacts of treatment sequences, namely, which technique should be employed first on the soil properties and the decontamination efficiency, are in high demand. This study provides a strategy to remove multiple heavy metals including Hg from a contaminated soil. The interactions between thermal treatment and chemical extraction on repartitioning of heavy metals was revealed. The obtained results could offer an integrating strategy to remediate the soil contaminated with both heavy metals and volatile contaminants.     

A comparison of physiologically based extraction test (PBET) and single-extraction methods for release of Cu, Zn, and Pb from mildly acidic and alkali soils

In vitro digestion test can be applied to evaluate the bioaccessibility of soil metals by measuring the solubility of the metals in synthetic human digestive tract. Physiologically based extraction test (PBET), composed of sequential digestion of gastric and intestinal phase, is one of the frequently used in vitro digestion tests. In this study, the PBET was chosen to determine the bioaccessibility of Cu, Zn, and Pb in 14 mildly acidic and alkali (pH 5.87–8.30) soils. The phytoavailability of Cu, Zn, and Pb in the same soils was also measured using six single-extraction methods (0.1 M HNO₃, 0.4 M HOAc, 0.1 M NaNO₃, 0.01 M CaCl₂, 0.05 M EDTA, and 0.5 M DTPA). The extraction efficiencies of the methods were compared. The PBET had a strong ability to extract metals from soil, which was much greater than neutral salt extraction and close to dilute acid and complex extraction in spite of the last 2 h neutral intestinal digestion. The amounts of bioaccessible Cu, Zn, and Pb in the gastric phase and in the gastrointestinal phase were both largely determined by the total content of soil Cu, Zn, and Pb. But the results of gastrointestinal digestion reflected more differences resulting from element and soil types than those of gastric digestion did. It was noticed that most of variations in the amounts of soil Cu, Zn, and Pb extracted by EDTA were well explained by the total soil Cu, Zn, and Pb, as same as the PBET. Moreover, the solubility of Cu, Zn, and Pb in the gastric phase and gastrointestinal phase were all positively linearly correlated with the results of EDTA. It was suggested that EDTA extraction can be used to predict the bioaccessibility of Cu, Zn, and Pb in mildly acidic and alkali (pH?>?5.8) soils, and the PBET and EDTA could be applied to measure, in a certain extent, the bioaccessibility and phytoavailability of Cu, Zn, and Pb in mildly acidic and alkali (pH?>?5.8) soils at the same time.     

Zero valent iron mediated degradation of the pharmaceutical diazepam

Parameters that influence the zero valent iron mediated degradation of the pharmaceutical diazepam (DZP) were evaluated including the iron concentration and its pre-treatment, the effect of complexation with EDTA and oxic versus anoxic condition. It was observed that acid pre-treatment of iron particles is important for degradation efficiency and that H₂SO₄ is a better choice than HCl, resulting in higher degradation of DZP. Under oxic conditions, the degradation of DZP achieved 96% after 60 min using Fe⁰ (25 g L⁻¹) pre-treated with H₂SO₄ in the presence of EDTA (119 mg L⁻¹), while mineralization achieved around 60% after the same time. Under anoxic conditions, degradation occurred, however at lower extent, achieving 67% after 120 min. The addition of EDTA improved the treatment efficiency in 20% leading to 99% DZP degradation after 120 min. The first intermediates formed during DZP degradation were identified using LC/MS analysis and revealed the formation of mono- and di-hydroxylated products from DZP during Fe⁰/EDTA/O₂ degradation, which evidences that OH was the main oxidizing species formed in this process.     

Adsorption and breakdown of penicillin antibiotic in the presence of titanium oxide nanoparticles in water

The fate and transport of antibiotics in natural water systems is controlled in part by interactions with nanometer (10⁻⁹ m) metal oxide particles. Experiments were performed by mixing solutions of ampicillin (AMP), a common, penicillin-class human and veterinary antibiotic, with 25 nm-TiO₂ (anatase) nanoparticles at different pH conditions. Both sorption and degradation of AMP were observed in the AMP-nanoparticle solutions. For AMP concentrations from ∼3 μM to 2.9 mM the overall AMP removal from solution can be described by linear isotherms with removal coefficients (K_r) of 3028 (±267) L kg⁻¹ at pH 2, 11,533 (±823) L kg⁻¹ at pH 4, 12,712 (±672) L kg⁻¹ at pH 6, and 1941 (±342) L kg⁻¹ at pH 8. Mass spectral analysis of AMP solutions after removal of the solid nanoparticles yielded ions that indicate the presence of peniclloic acid, penilloic acid and related de-ammoniated by-products as possible compounds resulting from the degradation of AMP at the TiO₂ surface.     

Chemical oxidation of cable insulating oil contaminated soil

Leaking cable insulating oil is a common source of soil contamination of high-voltage underground electricity cables in many European countries. In situ remediation of these contaminations is very difficult, due to the nature of the contamination and the high concentrations present. Chemical oxidation leads to partial removal of highly contaminated soil, therefore chemical oxidation was investigated and optimized aiming at a subsequent bioremediation treatment. Chemical oxidation of cable oil was studied with liquid H₂O₂ and solid CaO₂ as well as permanganate at pH 1.8, 3.0 and 7.5. Liquid H₂O₂ most effectively removed cable oil at pH 7.5 (24%). At pH 7.5 poor oil removal of below 5% was observed with solid CaO₂ and permanganate within 2 d contact time, whereas 18% and 29% was removed at pH 1.8, respectively. A prolonged contact time of 7 d showed an increased oil removal for permanganate to 19%, such improvement was not observed for CaO₂.Liquid H₂O₂ treatment at pH 7.5 was most effective with a low acid use and was best fit to a subsequent bioremediation treatment. To further optimize in situ chemical oxidation with subsequent bioremediation the effect of the addition of the iron catalyst and a stepwise liquid H₂O₂ addition was performed. Optimization led to a maximum of 46% cable oil removal with 1469 mM of H₂O₂, and 6.98 mM Fe(II) chelated with citric acid (H₂O₂:FeSO₄ = 210:1 (mol mol⁻¹). The optimum delivery method was a one step addition of the iron catalyst followed by step wise addition of H₂O₂.     

Determination of C(5)-C(12) perfluoroalkyl carboxylic acids in river water samples in the Czech Republic by GC-MS after SPE preconcentration

A method employing solid phase extraction followed by gas chromatography-mass spectrometry with negative chemical ionization has been developed for determination of ultratrace concentrations of perfluoroalkyl carboxylic acids in river water. The effects of the experimental parameters, such as the pH, additions of NaCl and an ion-pairing agent (tetraethylammonium bromide) and the kind of the elution agent, on the efficiency of the test acid extraction have been studied. The analyte extraction recoveries and the limits of detection and determination have been found. The method developed has been tested on determinations of perfluoroalkyl carboxylic acids in the waters of the two largest Czech rivers, Vltava and Labe (Elbe). The best extraction results have been attained without any alteration of the sample pH, with an addition of tetrabutylammonium bromide (a concentration of 50 μg mL⁻¹ in the sample) and using methanol as the elution agent. Under these conditions, the recoveries of the test acids in the spiked real samples are within ranges from 60% to 104% and 53% to 111% for analyte concentration levels of 1.40 ng mL⁻¹ and 0.14 ng mL⁻¹, respectively, depending on the lengths of the perfluorinated chains of the acids. In general, the recovery decreases with increasing length of this chain. The method developed exhibits very low limits of detection and determination and the results are fully comparable with those obtained when using more expensive HPLC-MS/MS instrumentation. Typical values amount to tenths to tens of pg mL⁻¹ and units to one hundred pg mL⁻¹ for the limits of detection and determination, respectively; the measuring sensitivity increases with increasing length of the analyte chain. The analyzes of real samples from the Vltava and Elbe rivers have demonstrated that the results obtained are similar to the values published for contamination of the Elbe and other rivers in western and central Europe. The concentrations determined are of the order of units to tens of pg mL⁻¹ and the C₈-C₁₀ acids occur most often.     

A novel application of H2O2-Fe(II) process for arsenate removal from synthetic acid mine drainage (AMD) water

Batch experiments were carried out to investigate the influences of H₂O₂/Fe(II) molar ratio, pH, sequence of pH adjustment, initial As(V) concentration, and interfering ions on As(V) removal in H₂O₂-Fe(II) process from synthetic acid mine drainage (AMD). The optimum H₂O₂/Fe(II) molar ratio was one for arsenate removal over the pH range of 4-7. Arsenate removal at pH 3 was poor even at high Fe(II) dosage due to the high solubility of Fe(III) formed in situ. With the increase of Fe(II) dosage, arsenate removal increased progressively before a plateau was reached at pH 5 as arsenate concentration varied from 0.05 to 2.0 mg L⁻¹. However, arsenate removal was negligible at Fe/As molar ratio <3 and then experienced a striking increase before a plateau was reached at pH 7 and arsenate concentration ≥1.0 mg L⁻¹. The co-occurring ions exerted no significant effect on arsenate removal at pH 5. The experimental results with synthetic AMD revealed that this method is highly selective for arsenate removal and the co-occurring ions either improved arsenate removal or slightly depressed arsenate removal at pH 5-7. The extended X-ray absorption fine structure (EXAFS) derived As-Fe length, 3.27-3.30 Å, indicated that arsenate was removed by forming bidentate-binuclear complexes with FeO(OH) octahydra. The economic analysis revealed that the cost of the H₂O₂-Fe(II) process was only 17-32% of that of conventional Fe(III) coagulation process to achieve arsenate concentration below 10 μg L⁻¹ in treated solution. The results suggested that the H₂O₂-Fe(II) process is an efficient, economical, selective and practical method for arsenate removal from AMD.     

Impact of lime-stabilized biosolid application on Cu,Ni, Pb and Zn mobility in an acidic soil

A soil column leaching study was conducted on an acidic soil in order to assess the impact of lime-stabilized biosolid on the mobility of metallic pollutants (Cu, Ni, Pb and Zn). Column leaching experiments were conducted by injecting successively CaCl₂, oxalic acid and ethylenediaminetetraacetic acid (EDTA) solutions through soil and biosolid-amended soil columns. The comparison of leaching curves showed that the transport of metals is mainly related to the dissolved organic carbon, pH and the nature of extractants. Metal mobility in the soil and biosolid-amended soils is higher with EDTA than with CaCl₂ and oxalic acid extractions, indicating that metals are strongly bound to solid-phase components. The single application of lime-stabilized biosolid at a rate ranging from 15 to 30 t/ha tends to decrease the mobility of metals, while repeated applications (2?×?15 t/ha) increase metal leaching from soil. This result highlights the importance of monitoring the movement and concentrations of metals, especially in acid and sandy soils with shallow and smaller water bodies.