双室微生物燃料电池型BOD传感器性能

构建了双室微生物燃料电池(MFC),并应用于污水BOD的检测。优化了MFC型BOD传感器的检测条件,分析了传感器进行污水BOD检测的特征。结果表明,以A2/O污水处理工艺中厌氧段污泥进行接种,双室MFC型BOD传感器2周内完成启动,所产电流达到稳定。传感器的最佳检测条件为外接电阻500Ω,添加缓冲溶液并维持待测水样pH为7.0,添加35 mg/L的L-半胱氨酸作为吸氧剂维持阳极室厌氧环境,阴极室富氧水流量为20 mL/min。利用MFC产生的电流峰值准确检测污水水样BOD浓度,传感器检测范围为10~50 mg/L,检测时间小于3 h;利用MFC产生的电荷量准确检测污水水样BOD浓度,检测范围为10~100 mg/L,检测时间小于10 h。利用MFC电流峰值和电荷量检测污水水样BOD浓度,偏差均小于15%,传感器运行稳定,寿命较长。     

2-乙基蒽醌修饰石墨毡催化电极电化学降解土霉素废水二级出水

采用自制的2-乙基蒽醌修饰石墨毡阴极,通过SEM、X射线衍射、循环伏安扫描曲线(CV)等方法对其微观形态和催化活性进行表征,并进行电化学降解土霉素废水二级出水实验研究。结果表明,2-乙基蒽醌修饰石墨毡阴极是良好的空气扩散电极,2-乙基蒽醌晶体的存在使石墨毡具有更高的电催化活性;当以钛涂钌铱DSA电极为阳极、2-乙基蒽醌修饰石墨毡为阴极,在电流密度0.06 A/cm2、极板间距4 cm、电解质浓度0.2 mol/L和不调节废水初始pH的条件下,电解60min,土霉素废水二级出水COD可由258.7~269.2 mg/L降低至105.0~118.6 mg/L,出水水质满足《化学合成类制药工业水污染物排放标准》(GB21904-2008)要求,COD降解动力学符合一级动力学方程。     

Fenton氧化-生化组合工艺处理染料中间体废水

针对染料中间体废水具有COD高、BOD5/COD低和具有生物毒性的特性,采用Fenton氧化-水解酸化-好氧组合工艺进行染料中间体生产废水的处理试验,试验结果表明:废水经Fenton氧化及水解酸化工序后,废水的BOD5/COD值由0.03升高至0.48,经好氧生化工序处理后的出水COD和BOD5浓度分别达122.6 mg/L和54.6 mg/L,符合《污水综合排放标准》(GB8978-1996)二级标准,该组合工艺COD总去除率达94%.     

禽类屠宰加工废水处理技术

介绍了厌氧水解酸化 循环活性污泥系统在禽类屠宰加工废水中的工程应用。结果表明 ,禽类加工废水在进水SS、CODCr、BOD5分别为 75 2mg/L、16 4 7mg/L、76 4mg/L的条件下 ,经该工艺处理后 ,外排废水的SS、CODCr、BOD5分别为 5 0mg/L、6 5mg/L、10 .1mg/L。该工艺具有占地面积小 ,处理效率好 ,运行费用低等特点 ,能广泛应用于禽类屠宰加工废水的处理。     

硫酸庆大霉素废水处理的研究

抗生素工业废水具有成分复杂、污染物浓度高、色度大、生物毒性等特点,比较难于治理。硫酸庆大霉素是常用的抗生素之一,其废水除具备上述特点外,还存在pH值波动范围大、水质、水量不均、SO42-浓度高等问题。本研究采用交换母液絮凝过滤-水解酸化-IC-SBR-MBR工艺处理含有硫酸庆大霉素的废水,在进水COD浓度6 000 mg/L～10 000 mg/L、SS浓度2 000 mg/L～3 000 mg/L的条件下,通过优化交换母液絮凝过滤药剂用量、水解酸化池废水停留时间、IC池的容积负荷、SBR池、MBR的污泥负荷等处理工艺,使出水水质能够达到COD 60 mg/L、BOD5 10 mg/L、NH3-N 10 mg/L。     

共基质下微生物燃料电池同步脱色甲基橙与产电性能

采用双室方形微生物燃料电池(MFC),以葡萄糖作为共基质,研究了共基质浓度对典型偶氮染料甲基橙在MFC阳极室中脱色效率及同步产电的影响。结果表明,在0~1.5 g/L浓度范围内,共基质浓度越大,甲基橙脱色率、COD去除率和最大输出电压越高。在共基质浓度为1.5 g/L,进水甲基橙为300 mg/L的条件下,8 h的脱色率高达95%,且在1 000Ω外电阻下,最大输出电压达到662 m V;在无共基质条件下,8 h内对300 mg/L甲基橙的脱色率仅为7.5%,最大输出电压仅达到140 m V。厌氧对照实验表明,甲基橙在MFC中可以实现加速脱色,反应8 h后甲基橙在MFC中的脱色率提高了57%。该研究为开发新型MFC降解偶氮染料废水技术提供了理论依据。     

UASB-接触氧化-气浮处理柠檬酸废水

介绍了UASB-接触氧化-气浮工艺处理柠檬酸废水的工程应用.工程运行表明,柠檬酸废水在进水SS、COD和BOD5分别为3427 mg/L、18 853 mg/L和11778 mg/L的条件下,经该工艺处理后,外排废水SS、COD和BOD5浓度分别为147.5 mg/L、223 mg/L和51.9 mg/L.该工艺具有占地面积小、工程投资和运行费用低及处理效果稳定等特点,能广泛应用于柠檬酸废水的处理.     

UASB-接触氧化-气浮处理柠檬酸废水

介绍了UASB-接触氧化-气浮工艺处理柠檬酸废水的工程应用.工程运行表明,柠檬酸废水在进水SS、COD和BOD5分别为3427 mg/L、18 853 mg/L和11778 mg/L的条件下,经该工艺处理后,外排废水SS、COD和BOD5浓度分别为147.5 mg/L、223 mg/L和51.9 mg/L.该工艺具有占地面积小、工程投资和运行费用低及处理效果稳定等特点,能广泛应用于柠檬酸废水的处理.     

三维电极-好氧生物法联合处理酸性染料废水模拟研究

采用电解-好氧生物法联合处理酸性大红G模拟废水，三维电解反应器填料为活性炭与玻璃珠混合物，平板电极材料为石墨，通过正交实验确定的最佳实验条件为：电解时间150min，活性炭／玻璃珠体积比为2：1，槽电压20V、pH为5、Na2SO4投加量1．5g／L，进水初始浓度2000mg／L。此时COD去除率及色度去除率分别可达49．78％和81．45％，废水BOD，／COD由0．12提高到0．42。电解后的废水采用生物接触氧化法处理12h后，出水COD为48mg／L，色度120倍，达到综合污水排放二级标准。     

微生物燃料电池与好氧堆肥协同处理餐厨垃圾

实验主张将餐厨固体垃圾和餐厨废水分开处理,并研究微生物燃料电池(MFC)作为餐厨废水和堆肥渗滤液处理工艺的可行性,通过调节不同的有机负荷,分析其生物产电的潜力和处理效率。对于餐厨废水而言,3 000 mg/L是较为理想的处理浓度,输出电压最高,始终维持在0.5 V以上;高于此浓度时电压输出特性与底物浓度呈现反相关,输出电压略低于0.5 V。极化曲线,电化学阻抗分析等也都表明3 000 mg/L是较为理想的处理浓度。而且在各种浓度下经MFC处理后的餐厨废水去除率均在90%左右,出水COD均低于400 mg/L。至于堆肥渗滤液,虽然在产电性能、去除效果上较餐厨废水稍差一些,但整体上与餐厨废水呈现出相似的规律。以上结果表明,餐厨垃圾中的废水可以通过MFC有效的去除和实现能量的回收。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Spectrophotometric Determination of Atmospheric Acidity by means of the Displacement of the Equilibrium of Acid-Base Indicators

A method is described for determining acidity by means of the spectrophotometric determination of the displacement of the equilibrium of açid-base indicators. The method is simple, sensitive and free of known interferences. There is no dependence on costly or sophisticated equipment and the results obtained are reliable and reproducible.     

实验室质量管理体系内部审核的策划

在实施ISO／IEC 17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核策划阶段的关键环节，提出审核范围确定、审核计划和抽样方案制订的质量控制要求，为有序高效地实施内部审核提供了技术方法。