生活污泥与煤混烧及热解特性

采用热重分析法,对生活污泥与煤以1∶1质量比混合的试样进行燃烧及热解实验研究,重点分析了升温速率对其热解及燃烧特性的影响,为煤泥混烧及热解技术的工业化应用提供理论支持。结果表明:煤泥混合样燃烧失重分为4个阶段,混燃过程中污泥与煤共同影响着混合试样的燃烧特性,随着升温速率从15℃·min~(-1)增加到50℃·min~(-1),其可燃性指数C增幅达60%和综合燃烧特性指数S提高了4倍多,燃烧性能得到明显提高;煤泥混合样的热解失重分为2个阶段,各阶段热解的挥发份最大析出速率(dw/dt)_(max)及挥发分析出特性指数D均随升温速率的升高而大幅增大,且试样总的挥发综合释放指数D从0.081 7×10~(-8)K~(-3)·min~(-2)增大到5.868×10~(-8)K~(-3)·min~(-2),可见升温速率越高,煤泥混合物的热解性能越好。     

废弃电路板中环氧树脂真空热解规律的研究

真空条件下,应用程序升温管式电炉对废弃电路板中环氧树脂热解规律进行了研究.考察了不同的热解终温(200～700 ℃)、升温速率(5～30 ℃/min)、真空度(以压力表征,3～30 kPa)及保温时间(10～150 min)对热解产物产率的影响.实验结果表明,热解终温是影响热解油产率最重要的因素;选择适当的热解终温(400～550 ℃)、升温速率(15～20 ℃/min)、真空度(15 kPa)及保温时间(30 min)有利于提高热解油产率.     

润滑油废白土的热解处理

以润滑油废白土为原料,利用电热解法,研究了热解终温、加热速率和CaO添加量对热解产物的影响。实验结果表明:热解终温对热解产物的影响最为显著。随着热解终温的升高,不凝气产量和产油率均迅速增加。当热解终温达到600℃时,其增加的速率逐渐缓慢增大。当控制热解终温为800℃、加热速率为16℃/min、CaO添加量为0.5%时,富氢气体产量为189.2 L/kg,气体中主要成分为H2和CH4,其含量分别为27.97%和41.64%;热解残渣含油率和重金属溶出物均低于标准规定值,热解油产率为10.98%,回收率为38.94%,其主要成分为汽油、柴油和重油3部分组成,分别含19.13%、31.35%和49.52%。     

市政污泥热解产油影响因素及产物应用特性

利用外热式固定床反应器,研究终温、反应时间、升温速率等因素对市政污泥热解产油率的影响,并对产物特性进行了讨论。结果表明,热解终温及反应时间显著影响焦油产率,500℃是适宜的污泥热解温度,焦油产率达24.74%,温度继续升高则半焦缩聚反应强烈,热解气产率大幅增加,焦油产率基本恒定;在10℃·min~(-1)的升温速率条件下,热解终温500℃,维持20 min,焦油产率可达到平衡;升温速率对焦油产率的影响不显著,热解反应达到平衡时,不同升温速率条件下,焦油产率相似;污泥焦油组分与中低温煤焦油相近,具备提酚、制燃料油和特种油品的潜力;污泥半焦灰分高,固定碳含量低,具有一定热值,比表面积较发达,掺混燃烧、制备吸附剂是其重要的潜在利用方向。     

城郊乡村生活垃圾衍生燃料热解特性研究

将城郊乡村生活垃圾加工成粒径6.0 mm左右的垃圾衍生燃料(RDF),采用热重(TG)分析和红外光谱等研究其热解特性.结果表明:(1)在RDF挥发分阶段和生物质挥发分阶段,助燃添加剂处于活泼分解阶段,加入了30％(质量分数)秸秆、玉米芯等生物质作助燃添加剂后的RDF(以下简写为混合RDF)分子碎片正发生内部氢重排,总体挥发分产物较多,并且有明显的二次裂解,失重提高到4.85 mg,失重率约提高12％.在RDF与生物质重叠的碳固定阶段,助燃添加剂失重率有一定提高,热重微分(DTG)峰值速率增加,为RDF碳固定阶段的进一步热解提供了良好的支持.(2)快加热产气速率均大于慢加热.(3)热解终温越高,越有利气体析出.(4)RDF的热解固体产率随着热解终温的升高而降低,在850℃时为31.9％;热解气体产率随着热解终温升高而迅速升高,在850℃时可达49.8％.(5)根据红外光谱图,城郊乡村生活垃圾加工成的RDF中所含的氯元素基本上以HCl形式释放.(6)一级动力学反应可以准确地描述物料热解过程.     

罐底含油泥热解动力学参数计算方法的优选

在化学反应设计中反应动力学是较重要的因素。为得到更合理的污泥热解动力学参数计算方法,利用热重分析仪,在氮气气氛下对罐底含油污泥的热解特性进行研究。根据热重实验数据,分别采用Coats-Redfern法、Kissinger法、FWO法和Popescu法计算污泥热解动力学参数,并获取罐底泥热解制油的主要阶段(第2阶段)的反应活化能E、频率因子A并分析各种方法反应机理。通过对比不同计算方法得到动力学参数及拟合曲线与实验曲线的相关性,确定了最佳罐底含油污泥热解动力学参数计算方法。研究表明,Popescu法得到罐底泥的热解过程符合Jander方程,活化能E为101.43 kJ/mol,与FWO法得到的91.20 kJ/mol相近,且预测曲线与实验曲线有较好的相关性(0.9816),说明Popescu法计算罐底泥热解动力学参数更合适。     

微波热解城市污水污泥的H2S释放影响因素研究

利用微波热解城市污水污泥是实现污泥无害化、减量化和资源化的有效出路之一,但热解过程中产生的恶臭气体(如H2S等)也会对大气环境造成严重的影响.以微波热解城市污水污泥10 min所收集的气体为研究对象,研究了热解终温、污泥含水率、升温速率及矿物催化剂种类4个因素对热解过程中H2S产量的影响.结果表明,随着热解终温的升高,城市污水污泥微波热解过程中的H2S产量逐渐上升,800℃时H2S产量为5.86 mg/g(以干污泥计,下同);含水率在50％～80％时,随着含水率的增加,城市污水污泥微波热解过程中的H2S产量逐渐上升,当含水率增至90％时,污泥出现了泥水分层现象,致使后续热解反应无法进行,故没有H2S产生;升温速率越快,热解反应的活化能越高,反应不易进行,H2S产量降低;添加矿物催化剂能有效固硫,且雷尼镍基催化剂的效果更好,热解终温为800℃时的H2S产量为4.15 mg/g,较不添加矿物催化剂时降低约30％;可通过铜铁吸收法和活性炭吸附两步工艺对热解产生的H2S加以吸收处理,处理后的H2S排放浓度满足《恶臭污染物排放标准》(GB 14554-93)中的厂界一级标准限值.     

不同升温速率下城市污水污泥热解特性及动力学研究

利用差热-热重分析法和Coats-Redfern积分法,对杭州某污水处理厂污泥在不同升温速率下的热解特性及反应动力学特征进行研究。实验结果表明,热解温度从室温升至900℃时,污泥热解过程可分为4个失重阶段;升温速率对污泥热解转化率、挥发分析出温度以及最大失重率等热解特性参数都有显著影响。升温速率越高污泥最大失重率越大;而较低的升温速率延迟了污泥热解反应时间,导致污泥失重量相对较大。根据Coats-Redfern积分法计算结果,污泥在氮气氛围下的热解反应为二级反应模式。提高升温速率可显著增加污泥热解的表观活化能和频率因子。     

污泥连续式微波热解制备生物气

采用升温迅速的微波能作为热源,利用自主设计微波设备对含水率为82%(m/m)的湿污泥进行高温热解实验。采用单因素实验法,探究热解终温、停留时间、活性炭添加量对污泥热解生物气组分和含量的影响规律,确定连续式运行的最佳工况条件:热解终温900℃,停留时间50 min,活性炭添加比例为30%,热解功率1 600 W;在此基础上进行连续12h微波高温热解实验,共热解污泥56 kg,产生生物气32.26 kg,热解油10.98 kg,固体残渣12.66 kg,产气转化率高达57.8%,生物气组分H_2+CO含量高达67%,热解产物具有良好的工业利用价值。污泥热解生物气中H2S浓度超标10倍以上,而NH_3浓度未超标,硫化氢的去除技术研究值得关注。     

镍基催化剂对污泥微波热解制生物气效能的影响

为实现污水污泥减量化、无害化及资源化的目标,在微波热解污水污泥基础上,进行了镍基催化剂对制取生物气效能影响的研究。采用元素分析对污泥元素进行检测,气/质联用分析(GC-MS)和气相色谱(GC)对热解生物气的组成和含量进行测定。实验结果表明,镍基催化剂的添加对微波热解污水污泥制取生物气有较大促进作用。5%添加量与800℃热解终温条件下具有最佳催化效果:生物气中H2、CO产量最大,H2产量由29 g/kg增加到35.8 g/kg,提升23.4%,CO产量由302.7 g/kg增加到383.3 g/kg,提升26.6%;同时催化剂还能提高热能利用效率,降低热解终温,即5%添加量在700℃热解终温时可达到空白800℃时的产气效果;镍基催化剂主要在500~600℃时发挥催化作用,加快了H2和CO的释放。微波热解污泥制取的生物气具有产量大、富含H2与CO等优点,可推动污水污泥的资源化进程。     

Field and laboratory studies of the fate and enantiomeric enrichment of venlafaxine and O-desmethylvenlafaxine under aerobic and anaerobic conditions

The stereoselectivity of R,S-venlafaxine and its metabolites R,S-O-desmethylvenlafaxine, N-desmethylvenlafaxine, O,N-didesmethylvenlafaxine, N,N-didesmethylvenlafaxine and tridesmethylvenlafaxine was studied in three processes: (i) anaerobic and aerobic laboratory scale tests; (ii) six wastewater treatment plants (WWTPs) operating under different conditions; and (iii) a variety of wastewater treatments including conventional activated sludge, natural attenuation along a receiving river stream and storage in operational and seasonal reservoirs. In the laboratory and field studies, the degradation of the venlafaxine yielded O-desmethylvenalfaxine as the dominant metabolite under aerobic and anaerobic conditions. Venlafaxine was almost exclusively converted to O-desmethylvenlafaxine under anaerobic conditions, but only a fraction of the drug was transformed to O-desmethylvenlafaxine under aerobic conditions. Degradation of venlafaxine involved only small stereoisomeric selectivity. In contrast, the degradation of O-desmethylvenlafaxine yielded remarkable S to R enrichment under aerobic conditions but none under anaerobic conditions. Determination of venlafaxine and its metabolites in the WWTPs agreed well with the stereoselectivity observed in the laboratory studies. Our results suggest that the levels of the drug and its metabolites and the stereoisomeric enrichment of the metabolite and its parent drug can be used for source tracking and for discrimination between domestic and nondomestic wastewater pollution. This was indeed demonstrated in the investigations carried out at the Jerusalem WWTP.     

骆马湖富营养化和生态状况调查与评价

为了了解骆马湖水质状况，在2005年对骆马湖富营养化状态和生态特性进行了调查，并结合“十五”期间的监测资料进行了分析。2005年骆马湖水体中总氮和总磷的平均值超《地表水环境质量标准》（GB3838-2002）中Ⅲ类，超标情况分别为0．78倍和0．54倍，达到湖库特定项目Ⅳ类水标准，骆马湖处于轻度富营养化状态。对骆马湖生态特征分析表明，由于该湖泊的形态以及“藻型浊水状态”和“泥沙型浊水状态”交替出现，遏制了湖水从高营养盐含量向全面富营养化状态演变，保障了底栖动物的良好生长环境，从而形成了骆马湖独特的环境生态平衡。     

Copper-catalyzed chlorination and condensation of acetylene and dichloroacetylene

The chlorination and condensation of acetylene at low temperatures is demonstrated using copper chlorides as chlorinated agents coated to model borosilicate surfaces. Experiments with and without both a chlorine source and borosilicate surfaces indicate the absence of gas-phase and gas-surface reactions. Chlorination and condensation occur only in the presence of the copper catalyst. C₂ through C₈ organic products were observed in the effluent; PCDD/F were only observed from extraction of the borosilicate surfaces. A global reaction model is proposed that is consistent with the observed product distributions. Similar experiments with dichloroacetylene indicate greater reactivity in the absence of the copper catalyst. Reaction is observed in the gas-phase and in the presence of borosilicate surfaces at low temperatures. The formation of hexachlorobenzene is only observed in the presence of a copper catalyst. PCDD/F were only observed from extraction of the borosilicate surfaces. A global reaction model is proposed for the formation of hexachlorobenzene from dichloroacetylene.     

Sources and distribution of polychlorinated-dibenzo-p-dioxins and -dibenzofurans in soil and sediment from the Yellow Sea region of China and Korea

Polychlorinated-dibenzo-p-dioxins and -dibenzofurans (PCDD/Fs) were measured in soils and sediments from the Yellow Sea region. Korean soils and sediments mostly contained detectable PCDD/Fs and showed a widespread distribution among locations. Soil and sedimentary PCDD/Fs from China were comparable to or less than those in Korea. The patterns of relative concentrations of individual congeners in soils were different between the two countries, but similar in sediments. Sources of PCDD/Fs in China and Korea were found to be independent of each other and their distributions reflected matrix-dependent accumulation. Spatial distribution indicated some point sources in Korea while Chinese sources were more widespread and diffuse. PCDD/Fs measured in the coastal areas of the Yellow Sea were comparable to or less than those previously reported in for eastern Asia. However, ∑TEQs in soils and sediments were near to or, in some cases exceeded environmental quality guidelines.     

Aerobic and anaerobic degradation of profluralin and trifluralin

Abstract

The degradation of profluralin [N‐(cyclopropylmethyl)‐α,α,α‐trifluoro‐2,6‐dinitro‐N‐propyl‐]p‐toluidine] and trifluralin (α,α,α‐trifluoro‐2,6‐dinitro‐N,N‐dipropyl‐p‐toluidine) was studied under aerobic and anaerobic soil conditions. Three soils (Goldsboro loamy sand, Cecil loamy sand, Drummer clay loam) were each treated with 1 ppmw herbicide; anaerobic conditions were maintained by flooding. Soil samples were extracted monthly and subjected to TLC analysis. No degradation was detected in sterile controls. Aerobic degradation of both herbicides was greatest in the Cecil loamy sand soil over the entire incubation period. Degradation of profluralin in Cecil soil under aerobic conditions was 86 percent after 4 months with three products detected; 83 percent of the trifluralin was degraded with two products detected. Anaerobic degradation accounted for 72 percent of the profluralin and 78 percent of the trifluralin after 4 months. Degradation of both herbicides increased with incubation time for the first 3 months and decreased slightly thereafter. Generally there was more extensive degradation (percent and in number of products formed) of profluralin than trifluralin under the conditions tested. More degradation products were detected for both herbicides under aerobic conditions than under anaerobic conditions.     

Quantification of carbamazepine and atrazine and screening of suspect organic contaminants in surface and drinking waters

A new approach for the identification of suspect trace organic contaminants in drinking and surface waters is presented. Samples were initially analyzed using a target determination method for two contamination tracers, carbamazepine (CBZ) and atrazine (ATZ). This method used offline solid-phase extraction and online solid-phase extraction techniques coupled to liquid chromatography-triple quadrupole mass spectrometry to accelerate the sample preparation process and improve method performance. CBZ and ATZ were found respectively in 31% and 56% of the samples, and concentrations were usually <20 ng L⁻¹. These samples were re-analyzed with a similar method on a quadrupole time-of-flight mass spectrometer to identify suspect contaminants by means of exact mass measurements and isotope patterns. A database of 264 common organic contaminants was built and used in conjunction with a Molecular Feature algorithm to identify the presence of these substances in drinking and surface water collected from different sources at various locations across Canada. Several organic contaminants were identified in the samples, but only the presence of caffeine, desethylatrazine, simazine and venlafaxine could be verified by comparison to pure standards. The presence of desethylatrazine was also confirmed by MS/MS experiments. These results suggest that target analysis for tracers of organic contamination may be a helpful tool to prioritize samples which should be further screened for suspect contaminants. This study also shows that the combination of separation techniques (offline and online SPE, LC) contribute to advance the applicability of high-resolution mass spectrometry for the identification of trace organic contaminants by accelerating the preparation step, reducing complexity and increasing analyte concentrations for optimal detection.     

Persistence and dissipation kinetics of trifloxystrobin and tebuconazole in onion and soil

The persistence and dissipation kinetics of trifloxystrobin and tebuconazole on onion were studied after application of their combination formulation at a standard and double dose of 75 + 150 and 150 + 300 g a.i. ha^?1. The fungicides were extracted with acetone, cleaned-up using activated charcoal (trifloxystrobin) and neutral alumina (tebuconazole). Analysis was carried out by gas chromatograph (GC) and confirmed by gas chromatograph mass spectrometry (GC-MS). The recovery was above 80% and limit of quantification (LOQ) 0.05 mg kg^?1 for both fungicides. Initial residue deposits of trifloxystrobin were 0.68 and 1.01 mg kg^?1 and tebuconazole 0.673 and 1.95 mg kg^?1 from standard and double dose treatments, respectively. Dissipation of the fungicides followed first-order kinetics and the half life of degradation was 6–6.6 days. Matured onion bulb (and field soil) harvested after 30 days was free from fungicide residues. These findings suggest recommended safe pre-harvest interval (PHI) of 14 and 25 days for spring onion consumption after treatment of Nativo 75 WG at the standard and double doses, respectively. Matured onion bulbs at harvest were free from fungicide residues.     

剩余污泥浓缩脱水投药量优化和模型建立

应用高分子阳离子絮凝剂（CPF-100）和聚丙烯酰胺（PAM）对污水厂剩余污泥进行浓缩脱水实验，研究表明：CPF-100的浓缩脱水效果优于PAM；当CPF-00投加量为1．16‰时，污泥沉降性能改善程度为37．51％；且在CPF-100投加量逐渐增大的初始阶段，污泥沉降性能改善程度随投加量的增加而增大，但CPF-100投加量也不宜过大，当CPF-100投加量超过1．16‰后，反而会使浓缩脱水效果变差。同时，建立了污泥沉降性能改善程度与絮凝剂CPF-100投加量、沉降时间之间的数学模型，其能较好地反映污水厂剩余污泥的浓缩脱水效果。     

Effects of compositional heterogeneity and nanoporosity of raw and treated biomass-generated soot on adsorption and absorption of organic contaminants

A biomass-generated soot was sequentially treated by HCl-HF solution, organic solvent, and oxidative acid to remove ash, extractable native organic matter (EOM), and amorphous carbon. The compositional heterogeneity and nano-structure of the untreated and treated soot samples were characterized by elemental analysis, thermal gravimetric analysis, BET-N₂ surface area, and electron microscopic analysis. Sorption properties of polar and nonpolar organic pollutants onto the soot samples were compared, and individual contributions of adsorption and absorption were quantified. The sorption isotherms for raw sample were practically linear, while were nonlinear for the pretreated-soot. The removal of EOM enhanced adsorption and reduced absorption, indicating that EOM served as a partitioning phase and simultaneously masked the adsorptive sites. By drastic-oxidation, the outer amorphous carbon and the inner disordered core of the soot particles were completely removed, and a fullerene-like nanoporous structure (aromatic shell) was created, which promoted additional π-π interaction between phenanthrene and the soot.     

Sorption and Desorption Behavior of Chloroanilines and Chlorophenols on Montmorillonite and Kaolinite

The bioavailability of pollutants, pesticides and/or their degradation products in soil depends on the strength of their sorption by the different soil components, particularly by the clay minerals. This study reports the sorption-desorption behavior of the environmentally hazardous industrial pollutants and certain pesticides degradation products, 3-chloroaniline, 3,4-dichloroaniline, 2,4,6-trichloroaniline, 4-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol on the reference clays kaolinite KGa-1 and Na-montmorillonite SWy-l. In batch studies, 2.0 g of clay were equilibrated with 100.0 mL solutions of each chemical at concentrations ranging from 10.0 to 200.0 mg/L. The uptake of the compounds was deduced from the results of HPLC-UV-Vis analysis. The lipophilic species were best retained by both clay materials. The most lipophilic chemical used in the study, 2,4,6-trichloroaniline, was also the most strongly retained, with sorption of up to 8 mg/g. In desorption experiments, which also relied on HPLC-UV-Vis technique, 2,4,6-trichloroaniline was the least desorbed from montmorillonite. However, on kaolinite all of the compounds under study were irreversibly retained. The experimental data have been modelled according to the Langmuir and Freundlich isotherms. A hypothesis is proposed concerning the sorption mechanism and potential applications of the findings in remediation strategies have been suggested.