Removal of nitric oxide in a biotrickling filter under thermophilic condition using Chelatococcus daeguensis

The development of a thermophilic biotrickling ?lter (BTF) system to inoculate a newly isolated strain of Chelatococcus daeguensis TAD1 for the effective treatment of nitric oxide (NO) is described. A bench-scale BTF was run under high concentrations of NO and 8% O₂ in thermophilic aerobic environment. A novel aerobic denitrifier Chelatococcus daeguensis TAD1 was isolated from the biofilm of an on-site biotrickling filter and it showed a denitrifying capability of 96.1% nitrate removal rate in a 24 h period in aerobic environment at 50 °C, with no nitrite accumulation. The inlet NO concentration fluctuated between approximately 133.9 and 669.6 mg m-3 and kept on a steady NOx removal rate above 80% in an oxygen stream of 8%. The BTF system was able to consistently remove 80–93.7% NO when the inlet NO was 535.7 mg m-3 in an oxygen stream of 2–20%. The biological removal efficiency of NO at 50 °C is higher than that at 25 °C, suggesting that the aerobic denitri?er TAD1 display well denitrification performance under thermophilic condition. Starvation for 2, 4 and 8 days resulted in the re-acclimation times of Chelatococcus daeguensis TAD1 ranging between 4 and 16 hours. A longer recovery time than that for weekend shutdown will be required when a longer starvation occurs. The results presented here demonstrate the feasibility of biotrickling ?lter for the thermophilic removal of NOx from gas streams.

Implications A novel denitrifier Chelatococcus daeguensis TAD1 was isolated from an on-site biotrickling filter in aerobic environment at 50 °C. To date, C. daeguensis has not been previously reported to be an aerobic denitrifier. In this study, a thermophilic biotrickling ?lter system inoculated with Chelatococcus daeguensis TAD1 for treatment of nitric oxide is developed. In coal-fired power plants, influent flue gas stream for nitrogen oxides (NO_x) removal typically exhibit temperatures between 50 and 60 °C. Traditionally, cooling gases to below 40 °C prior to biological treatment is inevitable, which is costly. Therefore, the application of thermophilic microorganisms for the removal of nitric oxide (NO) at this temperature range would offer great savings and would greatly extend the applicability of biofilters and biotrickling filters. Until now there has not been any study published about thermophilic biological treatment of NO under aerobic condition.     

好氧反硝化去除低浓度NO_x的动力学模型研究

在好氧条件下,对利用生物滴滤塔（bio-trickling filter,BTF）反硝化净化废气中NOx的过程进行了理论模型探讨,并用实验结果进行了验证。在分析NOx在BTF内传质以及生物降解过程的基础上,建立了NOx在气相和生物膜相的质量守恒方程,结合Fick定律和好氧条件下的Monod微生物反应动力学方程,最终得到了NOx在BTF中＂吸附-微生物降解＂过程的动力学方程。模型计算值与实验结果表明,BTF中好氧反硝化过程为一级反应过程,利用该模型可以较好地模拟进口浓度、停留时间等因素对出口浓度的影响,对实际应用具有指导意义。     

Abiotic and biological mechanisms of nitric oxide removal from waste air in biotrickling filters

Nitric oxide (NO) may participate in the ozone layer depletion and forming of nitric acid. Abiotic and biological mechanisms of NO removal from waste gases were studied in a biotrickling filter. The abiotic NO removal rate in the biotrickling filter was estimated by a review of the literature. The abiotic and biological removals were also verified in the biotrickling filter. The result has shown that chemical oxidation and bionitrification were both involved in the NO removal. It was found that the NO removal in high concentration (approximately 1000 ppm or higher) was in large measure the result of abiotic removal in both gas-phase and liquid-phase reactions. When NO concentration is low (less than approximately 100 ppm), bionitrification was the main process in the NO removal process in the biotrickling filter.     

C/N和pH值对高温好氧反硝化菌产N2O的影响研究

以50℃高温、好氧条件下能进行高效好氧反硝化的菌株TAD1为研究对象,在不同C/N和pH值培养条件下,对其24 h的反硝化效率和反硝化过程中N2O的逸出量进行了研究。结果显示,C/N和pH值对菌株TAD1的反硝化效率和N2O产生量有明显影响.菌株TAD1最适宜的C/N为9,pH值为7,此时反硝化效率达到99.12%,N2O产生量仅为3.35×10-2 mg/L,N2 O转化率为0.045%,反硝化产物以氮气为主。另外,菌株TAD1不适宜在酸性条件下生长,pH值为6时反硝化效率为83.18%,N2O产生量为13.88×10-2 mg/L,是pH值为7时的4.14倍,是pH值为8时的5.07倍。     

生物滴滤塔净化苯乙烯废气的实验研究

采用生物滴滤(BTF)系统对含苯乙烯的有机废气进行了生物净化实验并研究该系统VOCs生物降解性能。实验表明,苯乙烯进气浓度低于20 mg/m3时BTF去除效率可达92%以上,出口苯乙烯浓度低于1.6 mg/m3,达到GB14554-1993中规定的排放标准;该BTF装置对苯乙烯的去除负荷在2.0 g/(m3.h)左右;系统稳定运行时循环液COD、浊度和pH等都保持稳定,无脱落生物膜积累现象;生物滴滤塔系统适宜的气液比为300;系统总压降约100 Pa,鲍尔环填料和聚氨酯发泡填料混合装填方式可以降低系统压降并有利于微生物挂膜。     

Biotrickling filtration of nitric oxide

A biotrickling filter with blast-furnace slag packings (sizes = 20-40 mm and specific surface area = 120 m2/m3) was utilized to treat NO in an air stream. The operational stability, as well as the effects of gas empty-bed retention time (EBRT) and nutrient addition on the removal ability of NO, were tested. Approximately six weeks were required for the development of a biofilm for NO degradation, and a two-week organic carbon deficiency resulted in the detachment of biofilms from the packing surfaces. A steady removal rate of 80% was attained at specified influent NO concentrations of 892 to 1237 ppm and an EBRT of 118 sec. The effluent NO concentration diminished exponentially with enlarging EBRT, with influent NO concentrations of 203-898 ppm, and EBRTs of 25 to 118 sec. Nutrient addition is essential for efficient removal of the influent NO. Mass ratios of C: P: N = 7: 1: 30 and NaHCO3: NO-N = 6.3 could be used for practical applications.     

Biotrickling Filtration of Nitric Oxide

ABSTRACT

A biotrickling filter with blast-furnace slag packings (sizes = 20-40 mm and specific surface area = 120 m²/m³) was utilized to treat NO in an air stream. The operational stability, as well as the effects of gas empty-bed retention time (EBRT) and nutrient addition on the removal ability of NO, were tested. Approximately six weeks were required for the development of a biofilm for NO degradation, and a two-week organic carbon deficiency resulted in the detachment of biofilms from the packing surfaces. A steady removal rate of 80% was attained at specified influent NO concentrations of 892 to 1237 ppm and an EBRT of 118 sec. The effluent NO concentration diminished exponentially with enlarging EBRT, with influent NO concentrations of 203-898 ppm, and EBRTs of 25 to 118 sec. Nutrient addition is essential for efficient removal of the influent NO. Mass ratios of C: P: N = 7: 1: 30 and NaHCO₃: NO-N = 6.3 could be used for practical applications.     

Control of diesel gaseous and particulate emissions with a tube-type wet electrostatic precipitator

In this study, experiments were performed with a bench-scale tube-type wet electrostatic precipitator (wESPs) to investigate its effectiveness for the removal of mass- and number-based diesel particulate matter (DPM), hydrocarbons (HCs), carbon monoxide (CO), and oxides of nitrogen (NOx) from diesel exhaust emissions. The concentration of ozone (O3) present in the exhaust that underwent a nonthermal plasma treatment process inside the wESP was also measured. A nonroad diesel generator operating at varying load conditions was used as a stationary diesel emission source. The DPM mass analysis was conducted by means of isokinetic sampling and the DPM mass concentration was determined by a gravimetric method. An electrical low-pressure impactor (ELPI) was used to quantify the DPM number concentration. The HC compounds, n-alkanes, and polycyclic aromatic hydrocarbons (PAHs) were collected on a moisture-free quartz filter together with a PUF/XAD/PUF cartridge and extracted in dichloromethane with sonication. Gas chromatography (GC)/mass spectroscopy (MS) was used to determine HC concentrations in the extracted solution. A calibrated gas combustion analyzer (Testo 350) and an O3 analyzer were used for quantifying the inlet and outlet concentrations of CO and NOx (nitric oxide [NO] + nitrogen dioxide [NO2]), and O3 in the diesel exhaust stream. The wESP was capable of removing approximately 67-86% of mass- and number-based DPM at a 100% exhaust volumetric flow rate generated from 0- to 75-kW engine loads. At 75-kW engine load, increasing gas residence time from approximately 0.1 to 0.4 sec led to a significant increase of DPM removal efficiency from approximately 67 to more than 90%. The removal of n-alkanes, 16 PAHs, and CO in the wESP ranged from 31 to 57% and 5 to 38%, respectively. The use of the wESP did not significantly affect NOx concentration in diesel exhaust. The O3 concentration in diesel exhaust was measured to be less than 1 ppm. The main mechanisms responsible for the removal of these pollutants from diesel exhaust are discussed.     

A fungal vapor-phase bioreactor for the removal of nitric oxide from waste gas streams.

Ground-level O3 formation is becoming a major concern in many cities due to recent tightening of O3 regulations. To control O3 formation, more efficient treatment processes for O3 precursors, such as NOx and volatile organic compounds (VOCs), are needed. One promising new technology for removing both NOx and VOCs from off-gas streams is biofiltration, a simple process whereby contaminated air is passed through a biologically active packed bed. In this study, a toluene-degrading fungal bioreactor was used to treat an aerobic gas stream contaminated with NO. The fungal bioreactor removed 93% of the inlet 250-ppmv NO at an empty bed contact time (EBCT) of 1 min when supplied with 90 g/m3/hr toluene. The presence of NH4+ concentrations greater than 0.4 mg NH3/g dry packing medium, however, resulted in poor NO removal. The bioreactor achieved a maximum toluene elimination capacity of 270 g/m3/hr and maintained greater than 95% toluene removal efficiencies over the 175-day study period.     

Biodegradation of hydrogen sulphide by inoculated Rhodococcus sp.zw11 in a pilot-scale biotrickling filter

A strain of autotrophic micro-organism, Rhodococcus sp.zw11, was isolated from pharmaceutical wastewater containing hydrogen sulphide (H₂S). The shape, physiological and biochemical characteristics and oxidation capacity of Rhodococcus sp.zw11 were studied, and the effect of inlet concentration and volumetric loading of H₂S on the removal efficiency was evaluated by the biotrickling filter inoculated with Rhodococcus sp.zw11. The results suggested that the optimal temperature of Rhodococcus sp.zw11 (aerobic bacilli, short rod and gram-negative) was from 20°C to 28°C and the optimal pH was from 5.5 to 6.5. The criteria necessary for a scale-up design of the biotrickling filter were established, and pressure drops at the start and end of the experiment were investigated. The optimal inlet loading could be noted as 180 g/m³h, corresponding to H₂S removal efficiency close to 100%. Furthermore, the inoculated biotrickling filter had good ability to resist shock loading, which was a potential industrialisation method to control H₂S emissions.     

间歇运行式生物滴滤池处理油漆废气中试研究

为研究间歇运行式生物滴滤池对油漆生产厂废气净化能力，建立一座中试规模生物滴滤池（BTF），接种降解菌群，采用8 h/d运行方式净化某油漆厂包装车间废气，并用PCR-DGGE技术揭示BTF细菌群落结构与工艺运行条件间的联系。油漆厂包装车间废气中挥发性有机物（VOCs）主要为甲苯、乙苯、混合二甲苯（间、对和邻二甲苯），BTF对甲苯、乙苯、混合二甲苯最大去除率分别为88.8%、83.7%和86.3%。DGGE分析显示，BTF稳定运行时，主要优势菌相对丰度较为稳定（F，P>0.05），其细菌多样性显著低于启动期（F，P>0.05）；同时，下层填料细菌多样性高于上层填料，其细菌结构变化也较上层明显；另外，提升培养液浓度至2倍和4倍对菌群结构亦无显著影响。     

Effects of cross-substrate interaction on biotrickling filtration for the control of VOC emissions

The effects of cross-substrate interaction to the performance of a gas-phase biotrickling filter for treating a mixture of volatile organic compounds (VOCs), including three structural heterologous in acetone, toluene, and trichloroethylene, were investigated. The biotrickling filter was inoculated with microbial consortium containing at least seven bacterial species utilizing either acetone or toluene, or both, as their carbon sources. In the performance study, the column operating under variable conditions typifying the waste gas emission from the microelectronics fabrication processes achieved a total hydrocarbon (THC) removal efficiency in excess of 85% and a mineralization capacity over 50% for THC mass loading as high as 36.2 g-CH4 m-3h-1. The cross-substrate effects were examined by correlating the relative changes in the mass removal of each substrate with the biodegradative capability of the microbial consortium. The degradation of trichloroethylene was primarily due to co-metabolism by the toluene-oxidizing enzymes, but the results also indicated that trichloroethylene partially induced its own degradation. Concentration increases in acetone appeared to cause a diauxie effect that suppressed degradation of toluene and trichloroethylene, and shifted the microbial population toward the selective acetone-degraders. No irrecoverable toxicity or inhibitory effects were observed throughout the experiments. These results suggest that the relative VOC concentration in the waste gas mixture is a factor as important as the biodegradative function of the microbial consortium, and thus should be carefully evaluated to satisfy the treatment objectives.     

Treatment of 1,3-Butadiene in an Air Stream by a Biotrickling Filter and a Biofilter

ABSTRACT

This paper presents results obtained from a performance study on the biotreatment of 1,3-butadiene in an air stream using a reactor that consisted of a two-stage, in-series biotrickling filter connected with a three-stage, in-series biofilter. Slags and pig manure-based media were used as packing materials for the biotrickling filter and the biofilter, respectively. Experimental results indicated that, for the biotrickling filter portion, the butadiene elimination capacities were below 5 g/m³/hr for loadings of less than 25 g/m³/hr, and the butadiene removal efficiency was only around 17%. For the biofilter portion, the elimination capacities ranged from 10 to 107 g/m³/hr for loadings of less than 148 g/m³/hr. The average butadiene removal efficiency was 75–84% for superficial gas velocities of 53–142 m/hr and a loading range of 10–120 g/m³/hr. The elimination capacity approached a maximum of 108 g/m³/hr for a loading of 150 g/m³/hr. The elimination rates of butadiene in both the biotrickling filter and biofilter were mass-transfer controlled for influent butadiene concentrations below about 600 ppm for superficial gas velocities of 29–142 m/hr. The elimination capacity was significantly higher in the biofilter than in the biotrickling filter. This discrepancy may be attributed to the higher mass-transfer coefficient and gas-solid interfacial area offered for transferring the gaseous butadiene in the biofilter.     

The treatment of waste air containing phenol vapors in biotrickling filter

This research aimed at investigating the biodegradation of phenol contaminated-air streams in biotrickling filter. The effect of inlet concentration (200-1000 ppmv) and empty bed contact time (EBCT) (15-60 s) were investigated under steady state, transient and shock loading, and shutdown periods. Upon rapid start up operation, inlet phenol concentrations of up to 1000 ppmv did not significantly affect the performance of the biotrickling filter at EBCT of 60 s, so that removal efficiency was well greater than 99%. In addition, the EBCT as low as 30 s did not have detrimental effects on the efficiency of the bioreactor and phenol removal was greater than 99%. Decreasing the EBCT to 15s reduced the removal efficiency to around 92%. The maximum elimination capacity obtained in the biotrickling filter was 642 g(phenol) m(-3) h(-1), where the removal efficiency was only 57%. Results from the transient loading experiments revealed that the biotrickling filter could effectively handle the variations of the inlet loads without the phenol removal capacity being significantly affected.     

PCR-DGGE技术用于处理苯乙烯废气的生物滴滤塔中微生物优势菌种解析

采用生物滴滤塔能够有效去除含苯乙烯恶臭气体,塔内微生物中含有大量的球菌和杆状菌。采用聚合酶链式反应-变性梯度凝胶电泳(PCR-DGGE)技术研究处理苯乙烯恶臭气体的生物滴滤塔填料表面的微生物,结果表明,去除苯乙烯生物滴滤塔中有5种菌为降解苯乙烯的优势菌种;通过16S rDNA基因扩增测序同源性比对,结果显示嗜甲基杆菌属(methylophilus)丰度为50.5%,2种变形菌属(alpha proteobacterium、delta proteobacterium)相对丰度分别为16.9%和11.6%。     

Simultaneous Sulfur Dioxide and Nitrogen Dioxide Removal by Calcium Hydroxide and Calcium Silicate Solids

ABSTRACT

At conditions typical of a bag filter exposed to a coal-fired flue gas that has been adiabatically cooled with water, calcium hydroxide and calcium silicate solids were exposed to a dilute, humidified gas stream of nitrogen dioxide (NO₂) and sulfur dioxide (SO₂) in a packed-bed reactor. A prior study found that NO₂ reacted readily with surface water of alkaline and non-alkaline solids to produce nitrate, nitrite, and nitric oxide (NO). With SO₂ present in the gas stream, NO₂ also reacted with S(IV), a product of SO₂ removal, on the exterior of an alkaline solid. The oxidation of S(IV) to S(VI) by oxygen reduced the availability of S(IV) and lowered removal of NO₂. Subsequent acidification of the sorbent by the removal of NO₂ and SO₂ facilitated the production of NO. However, the conversion of nitrous acid to sulfur-nitrogen compounds reduced NO production and enhanced SO₂ removal. A reactor model based on empirical and semi-empirical rate expressions predicted rates of SO₂ removal, NO₂ removal, and NO production by calcium silicate solids. Rate expressions from the reactor model were inserted into a second program, which predicted the removal of SO₂ and NO_x by a continuous process, such as the collection of alkaline solids in a baghouse. The continuous process model, depending upon inlet conditions, predicted 30-40% removal for NO and 50-90% removal for SO₂. These x 2 results are relevant to dry scrubbing technology for combined SO₂ and NO_x removal that first oxidizes NO to NO₂ by the addition of methanol into the flue duct.     

优势菌种对餐厨垃圾高温好氧消化的促进

为研究优势菌种对餐厨垃圾高温好氧消化(TAD)的促进作用,本研究通过淀粉水解、油脂降解及明胶液化等生化实验,从餐厨垃圾中筛选出若干对其主要成分具有显著降解效果的优势菌种。通过对样品水溶性TOC(TOCw)、水溶性凯氏氮(KNw)、水溶性C/N(KNw)、pH以及含水率等指标的分析,考察优势菌种对餐厨TAD的促进作用。研究表明,优势菌种制剂最优添加量为1%。在此剂量下,好氧消化60 h,TOCw由8.53%降低为2.49%,C/Nw由18.71降低至6.14,以上指标说明加入优势菌种可加速TAD反应。添加量1%样本的水溶性凯氏氮和pH在反应48 h后开始回升,而未添加生物制剂的样本相关参数回升时间需96 h以上,由此推断优势菌种对TAD的促进机制是加快了蛋白质等大分子有机物的降解速度。     

Simultaneous removal of nitrogen oxide/nitrogen dioxide/sulfur dioxide from gas streams by combined plasma scrubbing technology

Oxides of nitrogen (NOx) [nitrogen oxide (NO) + nitrogen dioxide (NO2)] and sulfur dioxide (SO2) are removed individually in traditional air pollution control technologies. This study proposes a combined plasma scrubbing (CPS) system for simultaneous removal of SO2 and NOx. CPS consists of a dielectric barrier discharge (DBD) and wet scrubbing in series. DBD is used to generate nonthermal plasmas for converting NO to NO2. The water-soluble NO2 then can be removed by wet scrubbing accompanied with SO2 removal. In this work, CPS was tested with simulated exhausts in the laboratory and with diesel-generator exhausts in the field. Experimental results indicate that DBD is very efficient in converting NO to NO2. More than 90% removal of NO, NOx, and SO2 can be simultaneously achieved with CPS. Both sodium sulfide (Na2S) and sodium sulfite (Na2SO3) scrubbing solutions are good for NO2 and SO2 absorption. Energy efficiencies for NOx and SO2 removal are 17 and 18 g/kWh, respectively. The technical feasibility of CPS for simultaneous removal of NO, NO2, and SO2 from gas streams is successfully demonstrated in this study. However, production of carbon monoxide as a side-product (approximately 100 ppm) is found and should be considered.     

生物滴滤塔净化甲苯启动性能研究

研究以甲苯为驯导物的生物滴滤塔挂膜启动阶段净化性能的变化。实验结果表明,通过控制pH和湿度得到了真菌滴滤系统,启动周期为14 d,比细菌滴滤塔长7 d;在进化性能方面,在入口负荷、浓度为80 g/(m3.h)、3 000 mg/m3的条件下获得了稳定在98%以上的去除效率;对比2种填料对启动阶段的影响,在较低负荷下(≤80 g/(m3.h))对系统的启动时间和去除效率没有显著影响。     

The styrene purification performance of biotrickling filter with toluene-styrene acclimatization under acidic conditions

The obvious disadvantages of biotrickling filters (BTFs) are the long start-up time and low removal efficiency (RE) when treating refractory hydrophobic volatile organic compounds (VOCs), which limits its industrial application. It is worthwhile to investigate how to reduce the start-up period of the BTF for treating hydrophobic VOCs. Here, we present the first study to evaluate the strategy of toluene induction combined with toluene-styrene synchronous acclimatization during start-up in a laboratory-scale BTF inoculated with activated sludge for styrene removal, as well as the effects of styrene inlet concentration (0.279 to 2.659 g·m^?3), empty bed residence time (EBRT) (i.e., 136, 90, 68, 45, 34 sec), humidity (7.7% to 88.9%), and pH (i.e., 4, 3, 2.5, 2) on the performance of the BTF system. The experiments were carried out under acidic conditions (pH 4.5) to make fungi dominant in the BTF. The start-up period for styrene in the BTF was shortened to about 28 days. A maximum elimination capacity (EC_max) of 126 g·m^?3·hr^?1 with an RE of 80% was attained when styrene inlet loading rate (ILR) was below 180 g·m^?3·hr^?1. The highest styrene RE(s) [of BTF] that could be achieved were 95% and 93.4%, respectively, for humidity of 7.7% and at pH 2. A single dominant fungal strain was isolated and identified as Candida palmioleophila strain MA-M11 based on the 26S ribosomal RNA gene. Overall, the styrene induction with the toluene-styrene synchronous acclimatization could markedly reduce the start-up period and enhance the RE of styrene. The BTF dominated by fungi exhibited good performance under low pH and humidity and great potential in treating styrene with higher inlet concentrations.

Implications: The application of the toluene induction combined with toluene-styrene synchronous acclimatization demonstrated to be a promising approach for the highly efficient removal of styrene. The toluene induction can accelerate biofilm formation, and the adaptability of microorganisms to styrene can be improved rapidly by the toluene-styrene synchronous acclimatization. The integrated application of two technologies can shorten the start-up period of biotrickling filters markedly and promote its industrial application.