主导风向对不规则建筑群街区污染物扩散的影响

以城市道路某段典型的街道峡谷为研究对象,采用ICEM CFD数值模拟技术,分析不同风向对不规则建筑群街区污染物扩散影响。结果表明:(1)北风时,距地10.0m以下范围是污染物高浓度聚集区。与北风工况相比,西北风时街谷内污染物浓度分布变化较大,沿高度截面上升依次呈连续线状→线状和部分团状→断裂团状。(2)随着建筑高度的增加,主干道中的气流绕流作用减弱。通过控制建筑的连续界面诱导街谷中的气流横向绕流,或在临街上游设置合适的开敞空间,以增加来流通风廊道,可有效改善街谷中污染物的扩散。(3)两种风向下每条街道人员停留区内污染物停留时间排序规律相同;不同风向下每条街道人员停留区内污染物停留时间不同,说明风向对每条街道内污染物的影响存在差异,每段街谷内的污染物扩散分布不是孤立系统,而是相互关联的有机整体。     

杭州市风、逆温的气候特征与大气污染

影响大气污染物扩散和稀释的主要因素有两方面。1.气象的动力因子——风和湍流。两者对污染物在大气中的扩散与稀释起决定作用。大气湍流是气流作无规则运动。风包括风向、风速。风向决定污染物迁移方向,风速大     

高层建筑群对街谷内颗粒物扩散特性的影响

为了获得城市冠层内高层建筑群的高度变化对城市颗粒物污染的作用情况,采用大涡模拟方法研究了不同高层建筑群的街谷形状因子对街谷内空气流动与污染物扩散规律的影响。结果表明:在高层建筑群上方形成一个顺时针旋涡,旋涡中心位于城市峡谷内靠近高层建筑群背风处;随着街谷形状因子的增大,高层建筑群的滞留效应增强,导致高层建筑物上方的剪切层湍动能增强;当形状因子为2.5时,湍动能达到1.9 m~2·s~(-2),此时城市街谷内可吸入颗粒物的稀释扩散条件变差;在涡旋和气流夹带作用下,可吸入颗粒物浓度在垂直方向上分布具有明显的分层现象,大量可吸入颗粒物聚集于低建筑迎风面底部。不同街谷形状因子下街谷内空气流动与污染物扩散规律的探明将为有关部门制定相应规划提供参考。     

旋风静电除尘器流场分布测试研究

利用五孔探针系统对直筒式旋风静电除尘器模型的三维流场进行了测定与分析.结果表明:随着入口风速、供电电压增加,旋风静电除尘器内气流的切向和径向速度分别增加,各截面轴向速度沿半径的分布基本相似;与旋风除尘器相比,旋风静电除尘器内气流的切向速度和径向速度的变化更为平缓,入口风速为8.5 m/s时,在0.3～0.5倍简体直径时,切向速度达最大.     

SCR脱硝反应器烟道内部流场的数值模拟与优化

为优化无锡某电厂选择性催化还原脱硝反应器烟道内部流场,研究导流板和整流器对流场的影响,基于FLUENT软件和SIMPLE算法,采用RNG k-ε湍流模型和离散相模型数值模拟导流装置安装前、安装后和优化后3种情况下的烟道内部气流流动和固体颗粒流动.研究表明,导流板可以改善烟道内气流分布,同时保证气流进入催化剂层前的速度小于6 m/s,速度不均匀系数小于15％;整流器对改善气流流动、避免涡流存在具有重要作用,且对压降影响较小;合理的导流板结构和布置可以有效减小压降,导流板优化后压降降低至109.9 Pa.     

静压箱式错流生物滴滤床去除甲苯废气的研究

根据静压箱原理设计静压箱式错流生物滴滤床,设置进气静压区进一步改善气流分布情况,气流进入后在圆柱形静压区内动压降低,气流均匀分布.以甲苯为目标污染物、陶粒为填料、恶臭假单胞菌为菌源进行实验,研究静压箱式错流生物滴滤床的挂膜启动情况及稳定运行阶段甲苯停留时间、进气浓度对甲苯去除率的影响,分析了运行后期填料层压力损失增大的...     

底泥修复中温度对微生物活性和污染物释放的影响

通过分析底泥中微生物的酶活性以及污染物的释放规律,探讨了温度对河道底泥生物修复的影响.结果表明,底泥中微生物的脱氢酶、脲酶和磷酸酶的活性随着温度的升高而显著增大,但温度对纤维素酶的活性影响较小.4 ℃和10 ℃时底泥中污染物的释放量和微生物的酶活性均较低,水质较稳定;20～37 ℃时底泥中污染物的释放量明显增加,微生物的新陈代谢能力有较大提高,水体的自净能力较强.在各种因素的综合作用下,20～30 ℃是进行底泥生物修复的适宜环境温度.此外,当pH为9.0以及添加葡萄糖时,底泥中微生物均表现出较高的脱氢酶活性.     

新型活性焦干法脱硫脱硝脱汞反应塔流场的模拟与优化

在CFD软件Fluent中,选择k-ε湍流模型,多孔介质模型和SIMPLE算法,对新型脱硫脱硝脱汞反应塔内的三维流场进行数值模拟,结果发现,反应塔入口处烟气流场存在大漩涡。为消除漩涡,使穿过活性焦层的烟气均匀化,以充分利用活性焦层的空间来提高脱除效率,提出在入口处加装弯曲导流板,并通过相对标准偏差确定最优导流板长度。同时模拟了在最优喷氨位置处加装涡旋混合器时氨气和烟气的混合情况。结果表明,最优导流板长度(3.6 m)明显改善了烟气的均匀性,促使入口处的压降下降100 Pa左右。涡旋混合器形成的小漩涡,增强了烟气和氨气的混合。最后对照不同流量下实验值和模拟值的压降变化,验证了多孔介质模型的可行性。模拟结果对设备的优化设计和实际运行具有指导作用。     

影响有机污染物在土壤中的迁移、转化行为的因素

本文介绍了有机污染物在土壤中的吸附与解吸附、渗滤、挥发和降解等行为过程。探讨了吸附与解吸附机理、土壤有机质含量和类型、水分含量及温度等对此过程的影响。依据某些典型的化合物行为模型,论述了影响土壤中有机污染物渗滤的因素。有机污染物需要先从土壤深层迁移至地表,然后挥发至大气,在土壤中迁移的速率较慢,控制着整个挥发过程,可用Ｆｉｃｋ 第二定律来描述。有机污染物在土壤中的非生物降解主要包括氧化－ 还原、光解和水解等反应。土壤中的Ｏ２ 含量、土壤有机质成分和含量、辐射强度、光谱分布、土壤水分含量、温度和ｐＨ 值等都会影响非生物降解过程。其中有些因素通过影响微生物的生物活性,还影响有机污染物的生物降解     

活性炭固定沉积物中HCHs和DDTs的研究

在对沉积物的修复技术中,原位覆盖技术能够降低污染物向水体的释放,降低污染物对底栖生物和水生生物的生物可利用性,以及能够减少污染物向下游的迁移.在本研究中,将活性炭添加到受HCHs、DDTs污染的沉积物中,考察了活性炭剂量、粒径以及活性炭与沉积物接触的方式对HCHs、DDTs水相平衡浓度的影响,及对半渗透膜(SPMD)吸...     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Spectrophotometric Determination of Atmospheric Acidity by means of the Displacement of the Equilibrium of Acid-Base Indicators

A method is described for determining acidity by means of the spectrophotometric determination of the displacement of the equilibrium of açid-base indicators. The method is simple, sensitive and free of known interferences. There is no dependence on costly or sophisticated equipment and the results obtained are reliable and reproducible.     

实验室质量管理体系内部审核的策划

在实施ISO／IEC 17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核策划阶段的关键环节，提出审核范围确定、审核计划和抽样方案制订的质量控制要求，为有序高效地实施内部审核提供了技术方法。