氧化亚铁硫杆菌的筛选、生长特性及其橡胶再生研究

从大西洋底死火山口土壤中筛选出一株硫杆菌,经16S rDNA鉴定为氧化亚铁硫杆菌。研究了初始底物Fe2+浓度,初始pH,接种量对其生长的影响,确定了其最佳的生长的条件:在30℃、170 r/min条件下,最适底物Fe2+浓度为9 g/L,最佳初始pH为2.5,最适接种量为10%(体积分数)。探讨了氧化亚铁硫杆菌对天然硫化橡胶的脱硫再生,橡胶的SEM分析、FTIR图谱及EDS图谱研究表明氧化亚铁硫杆菌对硫化胶粉的硫交联键有断裂或转化作用,脱硫率达52.6%,氧化亚铁硫杆菌对天然橡胶具有一定的再生作用。     

铁镁质尾矿中的钙镁浸取效果优化

铁镁质尾矿含有丰富的钙镁,利用浸取剂可以促进铁镁质尾矿中钙镁的释放,使这些尾矿成为固定CO2的材料。尾矿中钙镁的浸出率大小跟多个因素相关,如何寻求浸取钙镁的最优化条件,是有效利用铁镁质尾矿的重要内容。考虑环境友好的方案,采用EDTA、柠檬酸和柠檬酸钠浸取尾矿中的钙镁,并对比了不同条件下的浸取效果。通过比较,显示柠檬酸钠的浸取效果较好,在此基础上利用响应面法对粒度、pH值、固液比等主要影响因子进行优化处理。当反应液的pH=1,尾矿粒度<75μm,固液比为2.6∶100时,模型预测实验尾矿淋滤的Mg2+浓度为143.4 mg/L,Mg达到最佳溶出率2.03%。实验模型的预测精度良好,表明响应面法适用于尾矿的浸取实验优化。     

柠檬酸强化钢渣湿法烧结烟气脱硫及机理

在鼓泡反应器中考察了添加柠檬酸强化钢渣湿法烧结烟气脱硫的影响因素,包括钢渣粒度,吸收浆液浓度、进口二氧化硫浓度、停留时间,p H值,柠檬酸与钢渣的浸泡时间等,结果表明,柠檬酸浓度为2.0 mmol/L、钢渣浓度为4%、二氧化硫进口浓度为1 500 mg/m3、烟气停留时间为7 s、钢渣强化时间为2 h、钢渣粒度200目,脱硫率达到90%以上。经4 mmol/L的柠檬酸强化后的钢渣浆液脱硫率比单纯钢渣浆液提高18.41%,达到90.99%的脱硫率,且有效反应时间延长50%,达到60 min以上。柠檬酸的加入,一方面促进了钢渣碱性组分溶解,另一方面在吸收液中形成柠檬酸和柠檬酸盐缓冲体系,增加了气液界面SO2浓度,提高了SO2的气液传质速率。     

矸石基X型分子筛对水中Co2+、Cu2+、Cd2+和Cr3+的去除

以煤矸石为原料,采用碱熔后水热合成法制备X型分子筛并进行XRD、SEM、BET和Zeta电位分析。研究其对水中Co2+、Cu2+、Cd2+和Cr3+4种离子的吸附性能,包括吸附等温线、吸附动力学以及初始金属离子浓度、pH值对吸附性能的影响。所合成的矸石基X型分子筛的BET比表面积为676.02 m2/g,微孔孔容为0.263 cm3/g。吸附实验表明,矸石基X型分子筛能有效去除上述4种离子,同时实现煤矸石的资源化和金属离子的去除。4种离子的平衡吸附量均随初始浓度的增大而增大,相同条件下平衡吸附量的大小顺序为Cd2+>Cr3+>Cu2+>Co2+。准二级动力学模型能很好地描述4种离子的吸附动力行为。Langmuir模型对Co2+、Cu2+和Cd2+吸附的拟合较Freundlich模型高,说明其主要表现为物理吸附过程。4种离子的吸附速率均由液膜扩散和颗粒内扩散共同控制。     

煤矸石微生物脱硫试验研究

采用本试验室自主分离筛选出的氧化硫硫杆菌,通过煤矸石浸泡的微生物脱硫和煤矸石柱状淋洗的微生物脱硫试验,研究该菌株对大武口高硫煤矸石的脱硫效果.煤矸石浸泡试验表明,微生物对煤矸石脱硫效果明显,浸泡煤矸石2 h后脱硫量达0.79 g/L,脱硫率达24.5%,21 d持续稳定升高,脱硫率达28.3%,为煤矸石的快速脱硫提供了技术支持.煤矸石柱状淋洗试验表明,前9 d是氧化硫硫杆菌脱硫的活跃期,该菌株有较高的氧化煤矸石的能力.     

酸浸法提取煤矸石中Al2O3的研究

煤矸石是主要的煤系固体废物,其中Al2O3质量分数约占35％左右.以某煤矿的煤矸石为原料,通过单因素实验比较盐酸和硫酸对Al2O3的浸取率,研究各因素对Al2O3浸取率的影响,确定浸取煤矸石中Al2O3的最佳酸浸介质为硫酸.利用正交实验确定酸浸取的最佳条件为:液固比(酸溶液体积与煤矸石样品质量比)15 mL/g、硫酸摩尔浓度3 mol/L、浸取时间120min、助样比(助溶剂与煤矸石样品质量比)0.20,在此条件下硫酸对煤矸石中A12O3的浸取率可达79.6％.     

盐单胞菌H17降解苯酚的响应面法优化及动力学

为获得盐单胞菌(Halomonas sp.)H17降解苯酚的最优条件,在单因素试验的基础上,通过Box-Behnken设计试验与响应面法,考察温度、pH、葡萄糖浓度对H17降解苯酚的影响,并通过动力学模型探究该菌株的生长和苯酚降解特性。结果表明,H17降解苯酚的最优条件为30℃、pH=8.0、葡萄糖质量浓度0.8g/L,在此条件下,苯酚降解率预测值为74.39%,实际值为73.92%,表明该模型可靠。该菌株降解苯酚动力学模型符合Haldane模型,其最大比降解速率、饱和常数和抑制常数分别为0.35h~(-1)、165.91mg/L和460.13mg/L。响应面法优化得到的生物降解条件准确,可为高盐含酚废水处理提供依据。     

煤矸石热活化性能研究

系统地研究了徐州夹河煤矸石在不同煅烧温度下的物理、化学变化及活性成分的溶出规律.采用扫描电子显微镜(SEM)、差热分析(DTA)、X射线衍射(XRD)等测试方法研究了热活化前后煤矸石的矿物组成、SiO2及Al2O3溶出率和微观结构,并采用水泥强度的测试方法对热活化煤矸石的活性进行宏观表征.结果表明,煅烧能有效去除有机挥发物和碳.破坏煤矸石中的硅氧键、铝氧键,形成无定形物质和玻璃相,从而提高煤矸石的活性.徐州夹河煤矸石的最佳热活化工艺条件是煅烧650℃、保温2 h.经此条件热活化后,SiO2和Al2O3的最高溶出率分别是76.32%、91.48%,添加50%(质量分数)的热活化煤矸石到水泥中,其强度比同掺量原样煤矸石的水泥强度提高了230%.     

氢氧化钠-钢渣双碱法烧结烟气脱硫工艺

在鼓泡反应器中考察了氢氧化钠-钢渣双碱法烧结烟气脱硫的主要影响因素。结果表明,在温度为常温,钢渣反应时间为2 h,钢渣加入量为40 g,SO2进口浓度为2 400 mg/m3,钢渣粒径为200目以上,烟气流量为0.05 m3/h,循环液pH保持在7～8,Na+浓度为0.5 mol/L,循环液为500 mL的条件下,脱硫率可长时间保持在80%以上。同时,对钢渣-氢氧化钠双碱法烧结烟气脱硫机理进行了探讨。     

突变灰盖鬼伞过氧化物酶降解刚果红的响应面法优化分析简

酶法降解偶氮染料刚果红是一个复杂的过程，受温度、pH、酶量、刚果红浓度和双氧水浓度显著影响。为研究各因素及因素间交互作用对刚果红降解影响，提高刚果红的降解率，分别使用单因素法和响应面分析法对刚果红降解条件进行了优化。单因素实验结果显示灰盖鬼伞过氧化物酶降解刚果红的最适条件为：pH 5.0、32℃、酶量4.98 U、双氧水0.1 mmol/L、刚果红20 mg/L，此时刚果红最高降解率为34.84%。然后选双氧水浓度、刚果红浓度和灰盖鬼伞过氧化物酶量作为3个因素，通过中心组合设计实验，用响应面法对刚果红降解进行优化分析，最后得到一个拟合度良好的二次多项方程模型（R²=0.9900）。方差分析结果显示，刚果红浓度和酶量是影响最显著的因素，双氧水与酶以及染料与酶之间的交互作用极显著。响应面分析优化后的反应体系为：双氧水浓度0.15 mmol/L，刚果红浓度为27.21 mg/L，酶为2.0 7 U，在此条件下，刚果红降解率达58.13%。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Spectrophotometric Determination of Atmospheric Acidity by means of the Displacement of the Equilibrium of Acid-Base Indicators

A method is described for determining acidity by means of the spectrophotometric determination of the displacement of the equilibrium of açid-base indicators. The method is simple, sensitive and free of known interferences. There is no dependence on costly or sophisticated equipment and the results obtained are reliable and reproducible.     

实验室质量管理体系内部审核的策划

在实施ISO／IEC 17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核策划阶段的关键环节，提出审核范围确定、审核计划和抽样方案制订的质量控制要求，为有序高效地实施内部审核提供了技术方法。