代谢产物积累对二氯甲烷生物降解的影响

研究了代谢调节产物(NaCl)浓度积累对生物法降解二氯甲烷效率的影响。试验表明,一定浓度的NaCl对二氯甲烷降解菌(GD11)的生长有不同程度的抑制作用。摇瓶试验中NaCl对二氯甲烷降解菌的抑制浓度为35.1g/L;当空塔气速91.7m/h、二氯甲烷进口浓度2.02g/m3、温度28.5℃、循环液流量0.06m3/h、pH值6.5～7.5时,生物滴滤塔中NaCl对二氯甲烷降解菌的抑制浓度为23.4g/L,两者相比有一定差异。NaCl浓度对生物膜的厚度有一定影响,这从侧面反映了NaCl浓度对微生物活性的影响。     

Nitric oxide removal by wastewater bacteria in a biotrickling filter

Nitric oxide(NO) is one of the most important air pollutants in atmosphere mainly emitted from combustion source. A biotrickling filter was designed and operated to remove NO from an air stream using bacteria extracted from the sewage sludge of a municipal sewage treatment plant. To obtain the best operation conditions for the biotrickling filter, orthogonal experiments(L9(34)) were designed. Inlet oxygen concentration was found to be the most significant factor of the biotrickling filter and has a significant negative effect on the system. The optimal conditions of the biotrickling filter occurred at a temperature of 40℃, a pH of 8.0 and a chemical oxygen demand of 165 mg/L in the recycled water with no oxygen in the system. The bacteria sample was detected by DNA sequencing technology and showed 93%–98% similarity to Pseudomonas mendocina. Moreover, a full gene sequencing results indicated the bacterium was a brand new strain and named as P. mendocina DLHK. This strain can transfer nitrate to organic nitrogen. The result suggested the assimilation nitrogen process in this system. Through the isotope experimental analysis, two intermediate products(15NO and 15N2O) were found. The results indicated the denitrification function and capability of the biotrickling filter in removing NO.     

Degradation of dichloromethane by an isolated strain Pandoraea pnomenusa and its performance in a biotrickling filter

A strain Pandoraea pnomenusa LX-1 that uses dichloromethane(DCM) as sole carbon and energy source has been isolated and identified in our laboratory. The optimum aerobic biodegradation of DCM in batch culture was evaluated by response surface methodology. Maximum biodegradation(5.35 mg/(L·hr)) was achieved under cultivation at 32.8°C, pH 7.3, and 0.66% NaCl. The growth and biodegradation processes were well fitted by Haldane's kinetic model, yielding maximum specific growth and degradation rates of 0.133 hr-1and 0.856 hr-1, respectively. The microorganism efficiently degraded a mixture of DCM and coexisting components(benzene, toluene and chlorobenzene). The carbon recovery(52.80%–94.59%) indicated that the targets were predominantly mineralized and incorporated into cell materials. Electron acceptors increased the DCM biodegradation rate in the following order: mixed oxygen iron sulfate nitrate. The highest dechlorination rate was 0.365 mg Cl-/(hr·mg biomass), obtained in the presence of mixed electron acceptors. Removal was achieved in a continuous biotrickling filter at 56%–85% efficiency, with a mineralization rate of 75.2%. Molecular biology techniques revealed the predominant strain as P. pnomenusa LX-1. These results clearly demonstrated the effectiveness of strain LX-1 in treating DCM-containing industrial effluents. As such, the strain is a strong candidate for remediation of DCM coexisting with other organic compounds.     

1株α-蒎烯降解菌的分离鉴定及降解特性研究

从处理废气的生物滤塔内筛选到1株能高效降解α-蒎烯的菌株PT.通过菌落形态、生理生化特征、16SrRNA基因序列相似性分析及Biolog鉴定等方法,确定该菌株属于荧光假单胞菌(Pseudomonas fluorescens).菌株PT最佳生长条件为: NaCl浓度0.00%、pH7.13、温度25.5℃,降解速率达到最大值5.22mg/(L×h).降解过程符合Haldane’s抑制生长动力学模型,最大比降解速率为0.0364h-1.菌株PT能不同程度地降解一些分子结构较为简单或与α-蒎烯结构相似的工业有机污染物.代谢产物分析表明,菌株PT在降解α-蒎烯的过程中产生柠檬油精、紫苏酸等结构较为简单的物质,它们最终被完全矿化为CO2或合成细胞自身组成物质.碳平衡分析表明,底物有机碳含量完全矿化和转化为细胞生物量的比例分别为64.83%和30.37%.     

生物滴滤池净化二氯甲烷废气的实验研究

在φ50mm生物滴滤池内进行了二氯甲烷废气净化的实验研究.由工厂活性污泥经驯化培养得到菌种,进一步接种、在填料表面挂膜,接种和挂膜约需30d.滴滤池内装填聚丙烯散堆填料,废气和循环液在滴滤池内逆流操作,循环液pH值为7.0±0.5,温度维持在28.5±2℃的条件下,生物膜系统能较好地适应进口浓度的变化.在气体空床停留时间为15.7s、二氯甲烷进口浓度为0.7～3.12g/m³的范围内,去除效率为72.0%～99.1%.滴滤池中的酸性环境对二氯甲烷的降解具有明显抑制作用.     

兼性厌氧苯胺降解菌的分离鉴定及其特性

从处理印染废水的厌氧折流板反应器(ABR)系统中分离、纯化并筛选出1株能以苯胺为唯一碳氮源进行代谢的兼性厌氧苯胺降解菌株AN29.经过形态、生理生化特征试验和16S rDNA序列分析结果,鉴定菌株AN29为假单胞菌(Pseudomonas sp.),其特性为:降解苯胺的最适温度为37℃,降解苯胺合适的起始pH值为6.5～8.0,可以利用苯胺的最高浓度为4 000mg/L,合适起始浓度为500～2 000mg/L.     

生物滴滤塔净化低浓度苯乙烯废气的研究

在生物滴滤塔中进行低浓度苯乙烯废气的生物净化实验,建立动力学模型,测定苯乙烯实验数据并定性定量检测生物膜微种群。当进口气体浓度为200～1000mg/m3、气体流量0.2～0.25 L/h、液体喷淋量10×10-3～12×10-3m3/h、停留时间50～65s、循环液体pH6.5～7.5时,净化效率为90%～99%。动力学模型的模拟计算值与实验值之间有很好的相关性,相关系数R为0.96～0.99。湿润生物膜微群落的优势菌种群包括恶臭假单胞菌、梭形芽胞杆菌、罗非氏不动杆菌等。恶臭假单胞菌的最大活菌数为5.5×107CFU/g,并随生物滴滤塔运行时间延长有减少趋势。     

好氧反硝化菌Bacillus sp. H2脱氮特性研究

文章从碳源、碳氮比、pH、温度及投菌浓度5个方面对好氧反硝化芽孢杆菌Bacillus sp.H2进行脱氮特性的研究.研究结果表明,以葡萄糖、乳糖作为碳源时,菌株Bacillus sp.H2的好氧反硝化效率要显著高于以乙醇、酒石酸钾钠、丁二酸钠、醋酸钠作为碳源时的效率,且葡萄糖略高于乳糖;当C/N≥6(质量比)时可进行完...     

一株草甘膦降解菌分离鉴定及其降解特性研究

从长期受草甘膦污染的土壤中筛选出10株草甘膦降解菌,其中A5菌株对草甘膦的降解率最高,经鉴定该菌株属于节杆菌属(Arthrobacter)。对A5菌株进行降解特性研究,结表明,该菌株降解草甘膦最适条件为:草甘膦600mg/L,葡萄糖10g/L,NaCl0.5g/L,pH6.5,32℃。在最适降解条件下,该菌株在72h时对草甘膦的降解率达94.2%。     

亚硝化单胞菌的分离鉴定及其降解特性的研究

对含有亚硝化菌的活性污泥进行富集和分离得到6株亚硝化菌,对其中降解效果最好的一株YS6菌株进行鉴定和降解特性研究。结果表明:该菌为亚硝化单胞菌(Nitrosomonas sp.),最适碳源CaCO_3和NaHCO_3,最适温度30℃,最适pH值8,250mL锥形瓶最佳装瓶量50 mL,接种量12×10~9个。     

4株邻苯二甲酸二丁酯降解菌的分离鉴定及其相关降解基因的克隆

从土壤中分离纯化出4株能降解邻苯二甲酸二丁酯(DBP)的菌株,分别命名为JDC-1、JDC-8、JDC-9、JDC-12,并对其进行了形态学、生理生化及分子生物学鉴定.菌株革兰氏染色阳性,16S rDNA序列分析显示4株菌均与节杆菌属(Arthrobacter sp.)有99%以上的序列相似性,初步判断这4株菌为Arthrobacter sp..通过PCR扩增及克隆,均获得了1个约900 bp的DNA片段,测序结果显示该片段与Arthrobacter keyseri的邻苯二甲酸3,4-双加氧酶基因的核苷酸序列相似性为96%以上.对4株菌的最适生长条件及对DBP的降解能力进行了分析,结果显示,4株菌的最适生长条件为pH 7.0~8.5,温度30~35℃.以DBP作为目标测试物,在适宜条件下测试了4株菌的降解能力,显示这4株菌均为高效降解菌,效率最高的JDC-1能在28 h内将500 mg/L的DBP降解完全,最慢的JDC-8经40 h能将500 mg/L的DBP降解完全,本研究对于DBP降解机制的研究及微生物资源的开发都具有重要意义.     

高效苯酚降解菌Bacillus sp.L5-1的分离及其降解特性

从污水处理厂活性污泥中分离筛选出一株高效苯酚降解菌L5-1,经菌落形态观察和16S rDNA基因测序,结果表明菌株L5-1为蜡样芽胞杆菌（Bacillus cereus）,美国国家生物信息中心（NCBI）的注册号为MN784421.将苯酚设置为唯一碳源,对其生长和苯酚降解特性展开研究.结果表明：菌株L5-1在10%接种量、温度30~35℃、pH值7~8的条件下,均能高效降解培养基中苯酚（培养基体积为100mL,初始苯酚浓度为500mg/L,14h时降解率>93%）.而在最优降解条件下（10%接种量,培养温度为35℃,pH值7.0,NaCl浓度为1%）,初始苯酚浓度为500mg/L,菌株在14h内的苯酚降解率可达97.1%;而当初始苯酚浓度为1000mg/L,菌株也可在46h内达到97.71%的降解率.运用Haldance方程动力学模拟菌株在不同浓度苯酚下的生长过程,其最大比生长速率为0.355h^-1,半饱合常数104.27mg/L,抑制常数为322.83mg/L,R²=0.997.菌株L5-1为目前已报道的Bacillus菌属中降解苯酚能力较强的菌株,为实际处理含酚废水中提供理论参考.     

一株耐盐原油降解菌的分离鉴定及其降解特性研究

通过对一株新分离到的耐盐原油降解菌进行形态学观察和生理生化鉴定,确定该菌株为假单胞菌(Pseudomonas sp).并对其生长特性和降解特性做了初步研究,确定了该菌株降解原油的最适条件为:原油的质量浓度为0.5 g/L、NaCl的质量浓度为30 g/L、pH值为8、温度30℃、摇床转速140 r/min、接种量为3%.在最适条件下,经过5 d的培养,原油的降解率为68%.实验结果表明该菌株治理海洋石油污染的应用前景较大.     

生物滴滤器中水分对憎水性气态污染物净化性能的影响

通过改变稳定工况下的液气比和测定风干过程中滴滤床净化和阻力性能变化,研究了水分对气体生物滴滤器(BTF)净化甲苯性能的影响,结果表明,生物滴滤器净化憎水性挥发性有机物的性能受滤床水分影响较大,与通常气液吸收过程不同,憎水性气体挥发性有机物的生物滴滤过程存在达到最佳净化效果的液气比,风干过程实验表明,滴滤器中水分含量太高,会影响憎水性污染物和氧气等在气相与生物相之间的传质过程;但水分太低又会影响滴滤器内生物相的活性,对生物滴滤器净化憎水性挥发性有机物而言,存在最适滤床水分,可通过监测设备压降来控制滴滤塔内水分。     

高温好氧反硝化菌的分离鉴定及其反硝化性能研究

通过高温筛选,从燃煤电厂生物滴滤系统填料的生物膜上分离出1株高效好氧反硝化细菌TAD1.该菌株革兰氏染色呈阴性,短杆状,大小为(0.67～0.89)μm×(1.03～1.41)μm;经生理生化特性和基于16S rDNA序列分析,初步鉴定该菌为螯台球菌属(Chelatococcus 8p.).对菌株TAD1的反硝化性能进...     

典型水环境因素对聚酯微塑料沉降的影响机制研究

以聚酯（聚对苯二甲酸乙二醇酯,简称PET）微塑料为主要对象,研究电解质浓度,电解质类型及pH值等典型水环境因素对其沉降行为的影响机制.结果表明：水环境中PET微塑料的沉降随电解质浓度的升高而不断增强,其悬液标准化浓度（C/C₀）最低可降至0.64;同一类型电解质对水环境中PET微塑料沉降行为的影响程度相似,而与1-1型电解质（NaCl及KCl）相比,水环境中1-2型电解质（CaCl₂及MgCl₂）的存在能够显著促进PET微塑料的沉降;水环境中PET微塑料的沉降随pH值的增加而降低,随着pH值由10降至4,PET微塑料悬液的C/C₀由最高0.98下降至最高0.76.一阶动力学沉降模型能够较好的拟合水环境中PET微塑料的沉降行为.此外,DLVO （Derjaguin-Landau-Verwey-Overbeek）理论能够反映出PET微塑料沉降行为的变化趋势,其计算结果与实验结果吻合度较高.本研究结果有助于提高对微塑料环境行为的认识程度,同时能够为评估微塑料环境风险提供理论依据.     

菲降解菌的特性及其降解酶纯化研究

研究考察了一株伯克霍尔德氏菌(Burkholderia sp.AFF)的基本特性,并对降解过程中的邻苯二酚2,3-双加氧酶进行了初步分离纯化。菌株AFF对链霉素和四环素具有抗性;当培养基中NaCl的浓度>1.5%时,菌株的生长降解能力受到抑制。菌株AFF生长与降解菲的最佳条件:温度30℃,pH=7.0,摇床转速为150r/min,接种量10%。菌株AFF的细胞粗提物具有邻苯二酚2,3-双加氧酶活性,用阴离子层析交换柱对其进行纯化,对收集到的具有酶活的组分进行SDS-PAGE分析,结果表明目的蛋白分子量在31kDa和43kDa之间。经过一步纯化后,比酶活提高33%,蛋白的回收率为27.6%。     

Production and application of a novel bioflocculant by multiple-microorganism consortia using brewery wastewater as carbon source

The flocculating activity of a novel bioflocculant MMF1 produced by multiple-microorganism consortia MM1 was investigated. MM1 was composed of strain BAFRT4 identified as Staphylococcus sp. and strain CYGS1 identified as Pseudomonas sp. The flocculating activity of MMF1 isolated from the screening medium was 82.9%, which is remarkably higher than that of the bioflocculant produced by either of the strains under the same condition. Brewery wastewater was also used as the carbon source for MM1, and the cost-effective production medium for MM1 mainly comprised 1.0 L brewery water （chemical oxygen demand （COD） 5000 mg/L）, 0.5 g/L urea, 0.5 g/L yeast extract, and 0.2 g/L （NH4）2SO4. The optimal conditions for the production of MMF1 was inoculum size 2%, initial pH 6.0, cultivating temperature 30℃, and shaking speed 160 r/min, under which the flocculating activity of the MMF1 reached 96.8%. Fifteen grams of purified bioflocculant could be recovered from 1.0 L of fermentation broth. MMF1 was identified as a macromolecular substance containing both protein and polysaccharide. It showed good flocculating performance in treating indigotin printing and dyeing wastewater, and the maximal removal efficiencies of COD and chroma were 79.2% and 86.5%, respectively.     

海洋费氏弧菌培养条件的研究

以本室保存的一株海洋费氏弧菌作为实验对象,采用单因素试验方法研究培养基起始pH值、盐浓度和摇瓶装液量等因素对菌株生长的影响,利用分光光度法测定其生长曲线,采用均匀设计方法,对该菌的培养基组分进行优化研究,确定其适合的生长条件,结果表明:当培养温度为30℃,通气量为180r/min时,该菌株在20h左右达到生长稳定期,对甘油的利用率要优于葡萄糖,盐浓度在5%以下时生长良好,最适装液量为60mL/250mL,培养液初始pH值为8.0。确定100mL培养基配方为:蛋白胨2g,酵母粉1.0g,氯化铵1.2g,氯化钠0.2g,磷酸二氢钾1.0g,此条件下可以得到最大的生物量。     

新型聚乙烯填料生物滴滤床净化硫化氢气体运行特性

研究高密度聚乙烯改良型拉西环填料按其不同规格分层填充后生物滴滤床去除硫化氢气体的运行特性.126d的长期运行试验结果表明,该反应器具有压降低、负荷沿塔高分布均匀的显著优点.在去除率90%时,气体停留时间最短为12s,入口负荷最大为110g/(m3·h),反应器最大去除负荷为84g/(m3·h).底层去除比率在37%～55%之间,负荷在2层填料间分布均匀.整个长期运行期间反应器压降一直低于280Pa/m,反冲周期大于2个月,长期运行底层未发生生物量积累,稳定运行时压降的变化可以作为反应器反冲的监控指标.故障恢复试验表明,反应器在停止供应气相基质6d后,去除率恢复到95%仅需1d,喷淋液pH的剧烈变化对于反应器具有明显的不良影响.