Numerical evaluation of the effectiveness of NO2 and N2O5 generation during the NO ozonation process

Wet scrubbing combined with ozone oxidation has become a promising technology for simultaneous removal of SO₂ and NO_x in exhaust gas. In this paper, a new 20-species, 76-step detailed kinetic mechanism was proposed between O₃ and NO_x. The concentration of N₂O₅ was measured using an in-situ IR spectrometer. The numerical evaluation results kept good pace with both the public experiment results and our experiment results. Key reaction parameters for the generation of NO₂ and N₂O₅ during the NO ozonation process were investigated by a numerical simulation method. The effect of temperature on producing NO₂ was found to be negligible. To produce NO₂, the optimal residence time was 1.25 sec and the molar ratio of O₃/NO about 1. For the generation of N₂O₅, the residence time should be about 8 sec while the temperature of the exhaust gas should be strictly controlled and the molar ratio of O₃/NO about 1.75. This study provided detailed investigations on the reaction parameters of ozonation of NO_x by a numerical simulation method, and the results obtained should be helpful for the design and optimization of ozone oxidation combined with the wet flue gas desulfurization methods (WFGD) method for the removal of NO_x.     

NOx和/或NH3气氛下SO2在高岭土表面非均相转化的实验研究

利用自制气溶胶反应器研究了NO_x和/或NH_3气氛下SO_2在高岭土表面的非均相转化过程,应用扫描电镜(SEM)对高岭土颗粒物形貌进行了表征.结果表明:高岭土颗粒表面的SO_2非均相转化致使其成分和形貌产生了较大变化.相同实验条件下,SO_2转化的协同作用程度由高到低依次为NH_3、NO_x/NH_3和NO_x气氛,相对湿度40%、有光照条件下,SO_2转化量增幅最高可分别达125%、75%和50%.所有气氛下,协同作用在无光照时在高相对湿度(40%~70%)区间更为突出,有光照时其显著性则体现在低相对湿度(20%~40%)区间.SO_2、NO_x、NH_3三者共存时,在高岭土颗粒表面发生的非均相反应过程既有协同作用又存在竞争反应.     

2020年和2021年南京城区臭氧生成敏感性和VOCs来源变化分析

PM_2.5和臭氧(O₃)协同防控是“十四五”期间空气质量提升的重点.O₃生成与其前体物挥发性有机物(VOCs)和氮氧化物(NO_x)呈高度非线性关系.基于南京市城区站点2020年和2021年的4～9月O₃、 VOCs和NO_x的连续在线监测数据,比较了两年间O₃及其前体物浓度的变化,进一步利用基于观测的盒子模型(OBM)和正定矩阵因子分解(PMF)模型分析了O₃-VOCs-NO_x敏感性和VOCs来源.结果表明,2021年的4～9月O₃日最大浓度、 VOCs和NO_x浓度的平均值相较于2020年同期约下降7%(P=0.031)、 17.6%(P<0.001)和14.0%(P=0.004).2020年和2021年的O₃超标天NO_x和人为源VOCs的平均相对增量反应活性(RIR)分别为0.17和0.14, 0....     

Activity and hydrothermal stability of CeO2–ZrO2–WO3 for the selective catalytic reduction of NOx with NH3

A series of CeO_2–ZrO_2–WO_3(CZW)catalysts prepared by a hydrothermal synthesis method showed excellent catalytic activity for selective catalytic reduction(SCR)of NO with NH_3 over a wide temperature of 150–550°C.The effect of hydrothermal treatment of CZW catalysts on SCR activity was investigated in the presence of 10% H_2O.The fresh catalyst showed above 90% NO_x conversion at 201–459°C,which is applicable to diesel exhaust NO_x purification(200–440°C).The SCR activity results indicated that hydrothermal aging decreased the SCR activity of CZW at low temperatures(below 300°C),while the activity was notably enhanced at high temperature(above 450°C).The aged CZW catalyst(hydrothermal aging at 700°C for 8 hr)showed almost 80% NO_x conversion at 229–550°C,while the V_2O_5–WO_3/TiO_2 catalyst presented above 80% NO_x conversion at 308–370°C.The effect of structural changes,acidity,and redox properties of CZW on the SCR activity was investigated.The results indicated that the excellent hydrothermal stability of CZW was mainly due to the CeO_2–ZrO_2 solid solution,amorphous WO_3 phase and optimal acidity.In addition,the formation of WO_3 clusters increased in size as the hydrothermal aging temperature increased,resulting in the collapse of structure,which could further affect the acidity and redox properties.     

富氧条件下等离子体协同改性NaY分子筛催化分解NO_x研究

用不同浓度的Cu、Ce和La离子交换Na Y分子筛,对比了不同改性条件下等离子体协同分解NO_x的性能.实验结果表明:Cu是NO_x催化分解的主要活性组分,对于8%Cu-Na Y催化剂,当放电电压为10 k V,放电功率为7.6 W时,NO_x转化率可达46.3%,反应产物中没有NO_2,只有11 ppm的N_2O.Ce的加入可以有效提高催化剂催化活性,对于5%Ce-8%Cu-NaY催化剂,当放电电压为7.8 kV,功率为3.6 W时,NO_x转化率可达67.3%.La的加入同样可以使催化剂活性上升,但不同La含量催化剂的NO_x转化率相差较小.     

Pd/CeZr/TiO2/Al2O3蜂窝状金属丝网催化剂选择催化还原NOX

采用溶胶-凝胶法和浸渍法制备了Pd/CeZr/TiO2Al2O3蜂窝状金属丝网催化剂,并将其应用于在富氧条件下以丙烯选择催化还原NOx的研究.利用扫描电镜(SEM)分析了钛酸四丁酯的含量以及涂敷次数对TiO2涂层的影响,系统地考察了Pd含量、氧气浓度和空速对蜂窝状金属丝网催化剂催化性能的影响.实验结果表明,采用钛酸四丁酯的含量为20.0%的溶胶,涂敷2次,可以在金属丝网载体上氧化铝涂层表面获得均匀、无皲裂的TiO2涂层;Pd含量在0.23%～1.06%的范围内, NOx的转化率随Pd含量的增加而减小, Pd含量为0.23%时, NOx表现最高的NOx转化率;反应气体中氧气浓度从1.5%增加到6.0%, NOx的转化率随氧气浓度的增加而增大,当氧气浓度高于6.0%, NOx的转化率则随氧气浓度的增加而迅速减小; NOx的转化率随着空速的增加而降低,在高温条件下空速对转化率的影响要大于在低温条件下.     

超声辅助法制备新型FeMOR分子筛催化NOx还原反应性能研究

采用超声辅助浸渍法成功合成了高铁含量的Fe MOR-5%-UL催化剂,并且测试其催化还原NO性能.研究发现在超声辅助条件下浸渍制得的催化剂可以引入更高比例的离子交换位上的孤立的Fe~(3+),这些铁离子具有更强的NO还原活性,因此超声辅助浸渍法制备的催化剂催化性能显著高于传统的离子交换法和浸渍法.其中活性最高的FeMOR-5%-UL催化剂在添加SO_2等多种气氛时,催化活性下降不显著.并且在持续100 h的汽车尾气条件下进行的稳定性实验中,FeMOR-5%-UL的催化活性没有明显下降.FeMOR-5%-UL的优异的催化活性和稳定性非常具有应用前景和研究价值.     

Synergistic impacts of anthropogenic and biogenic emissions on summer surface O3 in East Asia

A factor separation technique and an improved regional air quality model (RAQM) were applied to calculate synergistic contributions of anthropogenic volatile organic compounds (AVOCs),biogenic volatile organic compounds (BVOCs) and nitrogen oxides (NOx) to daily maximum surface O3(O3DM) concentrations in East Asia in summer (June to August 2000).The summer averaged synergistic impacts of AVOCs and NOx are dominant in most areas of North China,with a maximum of 60 ppbv,while those of BVOCs and NOx are notable only in some limited areas with high BVOC emissions in South China,with a maximum of 25 ppbv.This result implies that BVOCs contribute much less to summer averaged O3DM concentrations than AVOCs in most areas of East Asia at a coarse spatial resolution (1×1) although global emissions of BVOCs are much greater than those of AVOCs.Daily maximum total contributions of BVOCs can approach 20 ppbv in North China,but they can reach 40 ppbv in South China,approaching or exceeding those in some developed countries in Europe and North America.BVOC emissions in such special areas should be considered when O3 control measures are taken.Synergistic contributions among AVOCs,BVOCs and NOx significantly enhance O3 concentrations in the Beijing-Tianjin-Tangshan region and decrease them in some areas in South China.Thus,the total contributions of BVOCs to O3DM vary significantly from day to day and from location to location.This result suggests that O3 control measures obtained from episodic studies could be limited for long-term applications.     

Oxidation of diesel soot on binary oxide CuCr(Co)-based monoliths

Binary oxide systems (CuCr₂O₄, CuCo₂O₄), deposited onto cordierite monoliths of honeycomb structure with a second support (finely dispersed Al₂O₃), were prepared as filters for catalytic combustion of diesel soot using internal combustion engine's gas exhausts (O₂, NO_x, H₂O, CO₂) and O³ as oxidizing agents. It is shown that the second support increases soot capacity of aforementioned filters, and causes dispersion of the particles of spinel phases as active components enhancing thereby catalyst activity and selectivity of soot combustion to CO₂. Oxidants used can be arranged with reference to decreasing their activity in a following series: O₃ >> NO₂ > H₂O > NO > O₂ > CO₂. Ozone proved to be the most efficient oxidizing agent: the diesel soot combustion by O₃ occurs intensively (in the presence of copper chromite based catalyst) even at closing to ambient temperatures. Results obtained give a basis for the conclusion that using a catalytic coating on soot filters in the form of aforementioned binary oxide systems and ozone as the initiator of the oxidation processes is a promising approach in solving the problem of comprehensive purification of automotive exhaust gases at relatively low temperatures, known as the "cold start" problem.     

2019年7月石家庄市O3生成敏感性及控制策略解析

基于石家庄市2019年7月近地面污染物和气象观测数据,分析夏季O₃污染状况及其影响因素;结合WRF-CMAQ模式和O₃浓度等值线（EKMA曲线）,探究不同区域O₃-VOCs-NO_x的非线性响应关系,旨在探究最佳的前体物减排方案.结果表明,观测期间,石家庄市市区MDA8 O₃超标率高达70.9%.污染天期间,伴随着高温、低湿、小风,且以南风和东南风为主.石家庄市市区属于VOCs控制区,郊县为NO_x和VOCs协同控制区.在臭氧污染时段,市区在仅削减NO_x排放,且削减比例超过50%时,持续减排NO_x使得O₃浓度呈逐渐下降趋势.在非臭氧日时段,市区在VOCs和NO_x的削减比例大于1倍时,O₃浓度才不会出现反弹.对于市区应考虑以仅削减VOCs为先;对于郊县区域而言,不同的NO_x和VOCs削减比例下,O₃浓度均会下降...     

不同方法制备Co3O4催化剂CO-SCR性能及机制

氮氧化物(NOx)是造成细颗粒物、近地面臭氧等大气污染问题的重要前体物.随着大气污染治理行动的深入,对工业锅炉/窑炉烟气排放的NOx进行控制十分重要.采用不同方法制备了一系列Co_3O_4催化剂,考察了不同制备方法对CO选择性催化还原NO(CO-SCR)反应活性的影响,通过BET、XRD、Raman、HR-TEM和SEM等技术对该系列催化剂进行了表征.活性测试表明,以硫酸钴为前驱体用固态研磨法制备的Co_3O_4-S催化剂具有更优异的CO-SCR反应活性,且表现出较好的抗水蒸气性能,以醋酸钴为前驱体用固态研磨法制备的Co_3O_4-C催化剂显示出较好的抗水性能. NO氧化结果显示,催化剂的NO氧化效果越好,CO-SCR活性也越好. Raman表征结果显示,Co_3O_4-S表面可能含有更多的Co2+离子,从而有利于形成氧空位. H2-TPR结果表明,Co_3O_4-S催化剂的氧化还原性较好. HR-TEM表征发现Co_3O_4-S和Co_3O_4-O主要暴露(111)和(220)晶面,而更多(220)晶面的暴露可能更有利于反应的进行.     

关中盆地NO2和SO2对颗粒物污染的协同效应

基于WRF-Chem模式模拟了关中盆地2019年1月2—14日一次颗粒物污染事件,评估了NO_x和SO₂减排及其在颗粒物污染中的协同作用对PM_2.5污染的影响。敏感性实验结果表明：NO_x减排可使PM_2.5中硝酸盐含量下降,但大气中O₃浓度上升,大气氧化能力增强,其他二次组分上升,导致PM_2.5下降不明显;SO₂人为源减排可使硫酸盐质量浓度下降,但由于硫酸盐在PM_2.5中占比较低,当SO₂减排75%时,PM_2.5仅下降1.74%;当减排比例较高时,NO_x和SO₂同时减排更有利于颗粒物污染防治。PM_2.5质量浓度在NO_x和SO₂同时减排75%时比分开减排75%时多下降0.75%,主要是硫酸盐下降所致;对气溶胶含水量进行分析,发现NO_x对气溶胶含水量影响较大,当NO_x减排75%时,气溶胶含水量可下降15.51%;此外,NO_x和SO₂同时减排比分开减排时气溶胶含水量更低,更不利于二次颗粒物生成。     

人工智能助力臭氧催化剂SrFexZr1-xO3的开发

将人工智能应用于催化臭氧氧化催化剂SrFe_xZr_1-xO₃的开发过程,采用共沉淀法制备了50种不同配方的催化剂,考察聚乙二醇（PEG）投加量、煅烧时间、老化时间、氨水投加量和铁掺杂量对SrFe_xZr_1-xO₃催化剂催化臭氧降解间甲酚反应活性的影响.同时,利用人工神经网络（ANN）和响应面（RSM）对催化剂合成条件与TOC去除率和间甲酚转化率的关系进行拟合,训练集中ANN的R²值分别为0.91和0.97,高于RSM的R²值0.35和0.41;在4组测试集上ANN的均方误差（MSE）分别为9.87和17.67,远小于RSM的23.89和28.87.结果表明,ANN模型对催化剂制备过程的复杂体系具有更好的拟合和泛化能力.在ANN训练好的模型中通过枚举法寻找最优合成条件为：PEG投加量为19.00%,煅烧时间为1.25 h,老化时间为26.50 h,氨水投加量为6.21 mL,铁掺杂量为3.37%,所得催化剂为SrFe_0.13Zr_0.87O₃-B.最佳反应条件下,间甲酚转化率和TOC去除率分别达到98.52%和17.21%,优于空白组的73.46%和1.86%.     

成都市臭氧生成敏感性分析及控制策略的制定

利用OZIPR模式结合经验动力学建模方法(EKMA)模拟成都市2017年O_3生成过程并绘制EKMA曲线,模拟过程采用CB05机理描述系统的动力学机理,结果表明,成都市O_3生成处于VOCs控制区,同时存在NO_x单独减少的不利效应,O3控制策略应对VOCs进行减排或同时减排VOCs和NO_x.选取5种VOCs和NO_x减排比例进行计算,分析结果发现,VOCs与NO_x减排量呈线性关系:VOCs=0.77NO_x+0.18.成都市"十二五"规划中NO_x减排目标为19.13%,代入上式计算后知,VOCs需减排33%才能使O_3最大小时浓度达到环境空气质量的二级标准.利用臭氧生成潜势(OFP)计算14种VOCs人为排放源对O_3生成的贡献,结果显示,对OFP具有主要贡献的有8种排放源,将33%的VOCs减排目标分配到这8种排放源中,可得各排放源的VOCs减排目标:移动源11.88%、溶剂使用源10.23%、能源民用燃烧3.3%、化工行业2.97%、露天秸秆焚烧1.49%、餐饮0.83%、汽油蒸汽0.63%、建材行业0.59%.     

富氧条件下SnO2/Al2O3催化剂上丙烯选择性还原NOx的研究

考察了分别用浸渍法、共沉淀法和溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂上丙烯选择性还原NO_x的催化活性,发现制备方法与Sn的负载量对其活性有重要影响.溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂活性最高,Sn的最佳负载量为5%.与浸渍法和共沉淀法制备的5%SnO₂/Al₂O₃催化剂相比,溶胶-凝胶法制备的5%SnO₂/Al₂O₃催化剂受水蒸汽的抑制作用较弱,并且在水和SO₂共存的条件下活性最高.此外,反应气中丙烯及氧气浓度的增加有利于NO_x转化率的提高.     

Effects of WOx modification on the activity, adsorption and redox properties of CeO2 catalyst for NOx reduction with ammonia

A series of WO₃/CeO₂ (WOx/CeO₂) catalysts were synthesized by wet impregnation of ammonium metatungstate on a CeO₂ support. The resulting solid acid catalysts were characterized by X-ray diffraction (XRD), UV-Vis spectroscopy (UV-Vis), Raman spectroscopy (Raman), in-situ Fourier transform infrared spectroscopy (in-situ FT-IR) of ammonia adsorption, NH₃-TPD, H₂ temperature-programmed reduction (H₂-TPR), NH₃/NO oxidation and activity measurements for NOx reduction by NH₃ (NH₃-SCR). The results show that polytungstate (WOx) species are the main species of tungsten oxide on the surface of ceria. The addition of tungsten oxide enhances the Brönsted acidity of ceria catalysts remarkably and decreases the amount of surface oxygen on ceria, with strong interaction between CeO₂ and WOx. As a result, the N₂ selectivity of NH₃ oxidation and NH₃-SCR at high temperatures (> 300℃) is enhanced. Therefore, a wide working temperature window in which NOx conversion exceeds 80% (NOx conversion > 80%) from 200 to 450℃, is achieved over 10 wt.% WOx/CeO₂ catalyst. A tentative model of the NH₃-SCR reaction route on WOx/CeO₂ catalysts is presented.     

泰安市大气臭氧污染特征及敏感性分析

2018年5～7月对泰安市城区站点的臭氧及前体物进行在线监测,并基于特征比值法和光化学模型分析了臭氧及前体物的污染特征及臭氧生成对前体物的敏感性.结果表明,观测期间泰安市正遭受较为严重的臭氧(O_3)污染,臭氧浓度的日变化呈典型的单峰型变化,15:00左右出现最高值,氮氧化物(NO_x)和VOCs的日变化趋势整体呈现夜间高白天低的变化特征.由O_3生成效率(OPE)、VOCs/NO_x和H_2O_2/NO_z特征比值法及基于EKMA曲线的方法均得出观测期间泰安市大气O_3光化学生成偏向于NO_x敏感区及过渡区,削减NO_x和VOCs均对O_3生成具有控制作用.同时基于EKMA曲线的方法还得出在O_3前体物浓度减排时按照丙烯等效浓度(PE)与NO_x浓度比值为8∶3进行VOCs(PE)和NO_x削减可以达到O_3浓度控制的最佳效果.     

支持向量机回归在臭氧预报中的应用

采用南京工业区2016年5月20日~8月15日这一高臭氧（O₃）期的O₃、O₃前体物和常规气象资料数据,利用支持向量机回归（SVMr）方法分别预报O₃的小时值、日最大值和最大8 h滑动平均值.结果表明,O₃小时值预报的相关系数（R²）为0.84,平均绝对误差（MAE）和平均绝对百分误差（MAPE）分别为3.44×10^-9和24.48,O₃前期浓度、紫外B波段辐射（UVB）和NO₂浓度是关键因子.O₃日最大值预报的主要因子是NO_x在07：00的浓度和UVB.预报O₃ 8 h时UVB和气温起重要作用.加入前体物项能够使O₃的预报精度提升10%~28%.与多元线性回归方法相比,SVMr对O₃浓度的预报有明显优势.     

Oxidation of diesel soot on binary oxide CuCr(Co)-based monoliths

Binary oxide systems (CuCr₂O₄, CuCo₂O₄), deposited onto cordierite monoliths of honeycomb structure with a second support (finely dispersed Al₂O₃), were prepared as filters for catalytic combustion of diesel soot using internal combustion engine's gas exhausts (O₂, NO_x, H₂O, CO₂) and O₃ as oxidizing agents. It is shown that the second support increases soot capacity of aforementioned filters, and causes dispersion of the particles of spinel phases as active components enhancing thereby catalyst activity and selectivity of soot combustion to CO₂. Oxidants used can be arranged with reference to decreasing their activity in a following series: O₃ ? NO₂ > H₂O > NO > O₂ > CO₂. Ozone proved to be the most efficient oxidizing agent: the diesel soot combustion by O₃ occurs intensively (in the presence of copper chromite based catalyst) even at closing to ambient temperatures. Results obtained give a basis for the conclusion that using a catalytic coating on soot filters in the form of aforementioned binary oxide systems and ozone as the initiator of the oxidation processes is a promising approach in solving the problem of comprehensive purification of automotive exhaust gases at relatively low temperatures, known as the “cold start” problem.     

Characterization and performance of Pt/SBA-15 for low-temperature SCR of NO by C3H6

Pt supported on mesoporous silica SBA-15 was investigated as a catalyst for low temperature selective catalytic reduction(SCR) of NO by C 3 H 6 in the presence of excess oxygen.The prepared catalysts were characterized by means of XRD,BET surface area,TEM,NO-TPD,NO/C 3 H 6-TPO,NH 3-TPD,XPS and 27 Al MAS NMR.The effects of Pt loading amount,O 2 /C 3 H 6 concentration,and incorporation of Al into SBA-15 have been studied.It was found that the removal efficiency increased significantly after Pt loading,but an optimal loading amount was observed.In particular,under an atmosphere of 150 ppm NO,150 ppm C 3 H 6,and 18 vol.% O 2,0.5% Pt/SBA-15 showed remarkably high catalytic performance giving 80.1% NOx reduction and 87.04% C 3 H 6 conversion simultaneously at 140°C.The enhanced SCR activity of Pt/SBA-15 is associated with its outstanding oxidation activities of NO to NO 2 and C 3 H 6 to CO 2 in low temperature range.The research results also suggested that higher concentration of O 2 and higher concentration of C 3 H 6 favored NO removal.The incorporation of Al into SBA-15 improved catalytic performance,which could be ascribed to the enhancement of catalyst surface acidity caused by tetrahedrally coordinated AlO 4.Moreover,the catalysts could be easily reused and possessed good stability.