Source apportionment of ambient PM10 in urban areas of Wuxi, China

A total of 168 PM₁₀ samples were collected during the year of 2005 at eight sites in the city of Wuxi in China. Fifteen chemical elements, three water-soluble ions, total carbon and organic carbon were analyzed. Six source categories were identified and their contributions to ambient PM₁₀ in Wuxi were estimated using a nested chemical mass balance method that reduces the effects of colinearity on the chemical mass balance model. In addition, the concentrations of secondary aerosols, such as secondary organic carbon, sulfate and nitrate, were quantified. The spatially averaged PM₁₀ was high in the spring and winter (123 ??g·m^?3 and low in the summer-fall (90 ??g·m^?3). According to the result of source apportionment, resuspended dust was the largest contributor to ambient PM₁₀, accounting for more than 50% of the PM₁₀ mass. Coal combustion (14.6%) and vehicle exhaust (9.4%) were also significant source categories of ambient PM₁₀. Construction and cement dust, sulfates, secondary organic carbon, and nitrates made contributions ranging between 4.1% and 4.9%. Other source categories such as steel manufacturing dust and soil dust made low contributions to ambient PM₁₀.     

Trace metal content in inhalable particulate matter (PM<Subscript>2.5–10</Subscript> and PM<Subscript>2.5</Subscript>) collected from historical mine waste deposits using a laboratory-based approach

Mine wastes and tailings are considered hazardous to human health because of their potential to generate large quantities of highly toxic emissions of particulate matter (PM). Human exposure to As and other trace metals in PM may occur via inhalation of airborne particulates or through ingestion of contaminated dust. This study describes a laboratory-based method for extracting PM_2.5–10 (coarse) and PM_2.5 (fine) particles from As-rich mine waste samples collected from an historical gold mining region in regional, Victoria, Australia. We also report on the trace metal and metalloid content of the coarse and fine fraction, with an emphasis on As as an element of potential concern. Laser diffraction analysis showed that the proportions of coarse and fine particles in the bulk samples ranged between 3.4–26.6 and 0.6–7.6 %, respectively. Arsenic concentrations were greater in the fine fraction (1680–26,100 mg kg^?1) compared with the coarse fraction (1210–22,000 mg kg^?1), and Co, Fe, Mn, Ni, Sb and Zn were found to be present in the fine fraction at levels around twice those occurring in the coarse. These results are of particular concern given that fine particles can accumulate in the human respiratory system. Our study demonstrates that mine wastes may be an important source of metal-enriched PM for mining communities.     

Water-soluble inorganic ions in airborne particulates from the nano to coarse mode: a case study of aerosol episodes in southern region of Taiwan

In 2004, airborne particulate matter (PM) was collected for several aerosol episodes occurring in the southern region of Taiwan. The particulate samples were taken using both a MOUDI (Micro-orifice Uniform Deposit Impactor) and a nano-MOUDI sampler. These particulate samples were analyzed for major water-soluble ionic species with an emphasis to characterize the mass concentrations and distributions of these ions in the ambient ultrafine (PM_0.1, diameter <0.1 μm) and nano mode (PM_nano, diameter <0.056 μm) particles. Particles collected at the sampling site (the Da-Liao station) on the whole exhibited a typical tri-modal size distribution on mass concentration. The mass concentration ratios of PM_nano/PM_2.5, PM_0.1/PM_2.5, and PM₁/PM_2.5 on average were 1.8, 2.9, and 71.0%, respectively. The peak mass concentration appeared in the submicron particle mode (0.1 μm < diameter <1.0 μm). Mass fractions (percentages) of the three major water-soluble ions (nitrate, sulfate, and ammonium) as a group in PM_nano, PM_0.1, PM₁, and PM_2.5 were 18.4, 21.7, 50.0, and 50.7%, respectively. Overall, results from this study supported the notion that secondary aerosols played a significant role in the formation of ambient submicron particulates (PM_0.1−1). Particles smaller than 0.1 μm were essentially basic, whereas those greater than 2.5 μm were neutral or slightly acidic. The neutralization ratio (NR) was close to unity for airborne particles with diameters ranging from 0.18 to 1 μm. The NRs of these airborne particles were found strongly correlated with their sizes, at least for samples taken during the aerosol episodes under study. Insofar as this study is exploratory in nature, as only a small number of particulate samples were used, there appears to be a need for further research into the chemical composition, source contribution, and formation of the nano and ultrafine mode airborne particulates.     

Study on particulate and metallic elements variation at daytime and nighttime period in urban atmosphere

Daily PM_2.5, PM_2.5–10 and TSP have been collected by Universal and PS‐1 sampler simultaneously at a site within Taichung between February and March 1999. The filters were analyzed by atomic absorption spectrophotometry for the elemental analysis of Ca, Fe, Mn, Pb, Cu, Zn and Cr. In general, the concentration of these metallic elements are higher in fine particles than in coarse particles. On average, PM₁₀ accounted for 67% of the TSP at daytime, while at nighttime PM₁₀ accounted for only 44% of the TSP. For PM_2.5, PM₂._5–10 and TSP concentrations, there were no significant differences between day and night period. The averaged concentrations of metallic elements in PM_2.5 at daytime were all higher than that at nighttime. Ca, Fe and Zn have large and variable PM_2.5 concentrations at both daytime and nighttime. For the daytime Zn and Pb account for the largest portion of the heavy metal elements. For the nighttime, Zn and Cr make the largest portion of the heavy metal elements. The concentrations of Mn were higher on fine particulates. The trace metals Cu and Cr in Taichung are probably due to particulates emitted by Taichung Fire Power Plants transported into the sampling area by the prevailing northwesterly wind.     

Characterization of chemical species in universal sampler (PM2.5 and PM2.5–10) aerosols in suburban area of central Taiwan

Aerosol samples of particulate and chemical species for PM₁₀ (particulate matter with aerodynamic diameters less than 10 μm) collected by Universal sampler were studied from June to August 1998 in the suburban area of central Taiwan. The ratios of PM_2.5/PM_2.5–10 displayed that the fine particles (particle size < 2.5 μm) are prevailing in the suburban site. Ion Chromatography was used to analyze for the water‐soluble ions: sulphate and nitrate in the Universal samples. Also, the collected samples were analyzed by atomic absorption spectrophotometry for the elemental analysis of Ca, Fe, Pb, Cu and Cr. The results indicated that the crustal elements (Ca and Fe) and resuspended matters were dominated in the coarse particulate mode while the anthropogenic elements (Cr, Pb, Cu) and sulphate components are mainly in the fine particle fraction. The results also showed that the sulphate and nitrate make the largest portion of the chemical species collected by Universal sampler (PMio). The concentrations of heavy metals in THU are generally high, owing to the higher motor vehicle and industrial density nearby. The degree of pollution from this source differs from day to day, depending on the motor vehicle density.     

Health risk of aerosols and toxic metals from incense and joss paper burning

We report for the first time the distribution and hazard potential of aerosol and metals resulting from joss paper burning. Burning joss paper and incense is a traditional custom in many Oriental countries. Large amounts of air pollutants, including particles, polycyclic aromatic hydrocarbons, toxic metals and other gaseous pollutants, are released into the environment during the burning stage. Many investigations have reported on the emission of pollutants from the incense burning. However, no work has been reported until now on the analysis of the released pollutants apart from polycyclic aromatic hydrocarbons. In this study, a micro-orifice uniform-deposit impactor and inductively coupled plasma optical emission spectrometry were, respectively, used to collect aerosols and characterize the toxic metals from joss paper burning. We studied two types of particulate matter (PM): PM_2.5 that are particles with a diameter smaller than 2.5 μm and PM₁₀ that are particles with a diameter smaller than 10 μm. PM_2.5 are the most potentially toxic particles. Our results showed that PM_2.5 are the major component of the pollutants and that the PM_2.5 to PM₁₀ ratio ranged from 62 to 99%. The metals Na, Ca, Mg, Al and K were the main species in the aerosol and in the bottom ash.     

Modelling concentrations of airborne primary and secondary PM10 and PM2.5 with the BelEUROS-model in Belgium

The Eulerian Chemistry-Transport Model BelEUROS was used to calculate the concentrations of airborne PM₁₀ and PM_2.5 over Europe. Both primary as well as secondary particulate matter in the respirable size-range was taken into account. Especially PM_2.5 aerosols are often formed in the atmosphere from gaseous precursor compounds. Comprehensive computer codes for the calculation of gas phase chemical reactions and thermodynamic equilibria between compounds in the gas-phase and the particulate phase had been implemented into the BelEUROS-model. Calculated concentrations of PM₁₀ and PM_2.5 are compared to observations, including both the spatial and daily, temporal distribution of particulate matter in Belgium for certain monitoring locations and periods. The concentrations of the secondary compounds ammonium, nitrate and sulfate have also been compared to observed values. BelEUROS was found to reproduce the observed concentrations rather well. The model was applied to assess the contribution of emissions derived from the sector agriculture in Flanders, the northern part of Belgium, to PM₁₀- and PM_2.5-concentrations. The results demonstrate the importance of ammonia emissions in the formation of secondary particulate matter. Hence, future European emission abatement policy should consider more the role of ammonia in the formation of secondary particles.     

Characteristics of mass distributions of aerosol particle and its inorganic water-soluble ions in summer over a suburb farmland in Beijing

Agricultural activity is one of the most important sources of aerosol particles. To understand the mass distribution and sources of aerosol particles and their inorganic water-soluble ions in a suburb farmland of Beijing, particle samples were collected using a microorifice uniform deposit impactor (MOUDI) in the summer of 2004 in a suburb vegetable field. The distribution of the particles and their inorganic water-soluble ions in the diameter range of 0.18–18 μm were measured. The dominant fine particle ions were SO₄ ^2?, NO₃ ^?, and NH₄ ⁺. The association of day-to-day variation of the concentration of these ions with temperature, humidity, and solar radiation suggested that they are formed by the reaction of NH₃ released from the vegetable field with the acid species produced from photochemical reactions. Fine particle K⁺ is likely from vegetation emission and biomass burning. Coarse particles like Ca²⁺, Mg²⁺, NO₃ ^?, and SO₄ ^2? are suggested to come from the mechanical process by which the soil particle entered the atmosphere, and from the reaction of the acid species at the surface of the soil particle. The results show that fertilizer and soil are important factors determining the aerosol particle over agricultural fields, and vegetable fields in suburban Beijing contribute significantly to the aerosol particle.     

Characterization of indoor dust from Brazil and evaluation of the cytotoxicity in A549 lung cells

Over the past decade, ambient air particulate matter (PM) has been clearly associated with adverse health effects. In Brazil, small and poor communities are exposed to indoor dust derived from both natural sources, identified as blowing soil dust, and anthropogenic particles from mining activities. This study investigates the physicochemical and mineralogical composition of indoor PM₁₀ dust samples collected in Minas Gerais, Brazil, and evaluates its cytotoxicity and inflammatory potential. The mean PM₁₀ mass concentration was 206 μg/m³. The high dust concentration in the interior of the residences is strongly related to blowing soil dust. The chemical and mineralogical compositions were determined by ICP-OES and XRD, and the most prominent minerals were clays, Fe-oxide, quartz, feldspars, Al(hydr)oxides, zeolites, and anatase, containing the transition metals Fe, Cr, V, Ni, Cu, Zn, Ti, and Mn as well as the metalloid As. The indoor dust samples presented a low water solubility of about 6 %. In vitro experiments were carried out with human lung alveolar carcinoma cells (A549) to study the toxicological effects. The influence of the PM₁₀ dust samples on cell viability, intracellular formation of reactive oxygen species (ROS), and release of the pro-inflammatory cytokine IL-8 was analysed. The indoor dust showed little effects on alamarBlue reduction indicating unaltered mitochondrial activity. However, significant cell membrane damage, ROS production, and IL-8 release were detected in dependence of dose and time. This study will support the implementation of mitigation actions in the investigated area in Brazil.     

Characterization and distribution of mineral content in fine and coarse airborne particle fractions by neutron activation analysis∗

Nowadays, much attention is devoted to the study of toxic elements at trace and sub-trace levels in the investigation of particulate matter composition, especially in PM₁₀ and PM_2.5. Furthermore, it should be considered that the behavior knowledge is an other important task for understanding such species. Finally, the determination of particular elements with a few data in literature can assume relevant importance in industrial processes (Pd, Rh, Ir, etc. for catalytic pot, Sm, Ce, Eu, etc. for optical fibers and electronic process). In this article, we apply a nuclear technique, i.e. Instrumental Neutron Activation Analysis, for the study of metal composition in fine and coarse fractions. This nuclear technique allows the determination of about 25 elements: for some of them, this is the first determination in the ambient air of Rome. The investigation was performed in a reserved area in downtown Rome during a 15-day intensive campaign. The sampled filters were irradiated at the nuclear reactor Triga Mark II (ENEA-Casaccia Laboratories) at neutron flux of 2.6?×?10¹²?n?cm^?2?s^?1 for 32.55?h. The measurements of the γ-ray allow the qualitative and quantitative analysis. The element levels in fine and coarse fractions will be shown with the correlations among some elements being more interesting in the toxicological field: basically, the concentrations are very low.     

The pollution characteristics of PM<Subscript>2.5</Subscript> and correlation analysis with meteorological parameters in Xinxiang during the Shanghai Cooperation Organization Prime Ministers’ Meeting

The pollution characteristics of PM_2.5 and correlation analysis with meteorological parameters in Xinxiang during the Shanghai Cooperation Organization Prime Ministers’ Meeting were investigated. During the whole meeting, nine PM_2.5 samples were collected at a suburban site of Xinxiang, and the average concentration of PM_2.5 was 122.28 μg m^?3. NO₃ ^?, NH₄ ⁺, SO₄ ^2? accounted for 56.8% of the total water-soluble ions. In addition, with an exception of Cl^?, all of water-soluble ions decreased during the meeting. Total concentrations of crustal elements ranged from 6.53 to 185.86 μg m^?3, with an average concentration of 52.51 μg m^?3, which accounted for 82.5% of total elements. The concentrations of organic carbon and elemental carbon were 7.71 and 1.52 μg m^?3, respectively, lower than those before and after the meeting. It is indicated that during the meeting, limiting motor vehicles is to reduce exhaust emissions, delay heating is to reduce the fossil fuel combustion, and other measures are to reduce the concentration of PM_2.5. The directly dispersing by mixing layerheight increase and the indirectly reducing the formation of secondary aerosol by low relative humidity, andthese are the only two key removing mechanisms of PM_2.5 in Xinxiang during the meeting.     

北京大气气溶胶单个颗粒的化学表征

用安德逊分级采样器采集京都三个点（北辛安，冷泉村和生态环境研究中心）的大气气溶胶颗粒，用扫描电镜／Ｘ射线能谱观察和分析单个颗粒的形貌和元素成分，对粗细颗粒分别进行了Ｘ射线物相分析，通过对颗粒的形貌，组分和化合物形态等的综合分析结果表明，细粒样品中常含有较多的铁或铵的硫酸盐及氯化铵，粗粒样品中则主要为矿物物质如石英，方解石，石膏，白云石和一些粘土矿物，圆形颗粒可能是煤的燃烧产物，许多不规则形的颗粒大     

Distribution,geochemistry, and mineralogy of aerosols in the Angouran Mine area,northwest Iran

The Angouran Mine, located in northwest Iran, is the largest Zn–Pb producer in the Middle East. This study was designed to investigate the distribution, geochemistry, and mineralogy of the aerosols in the mining area and to assess their likely health impacts on the local residents. For this purpose, 36 aerosol samples were collected from 2014 to 2015 at nine sites located in mine district and upwind and downwind directions. The concentration of potentially toxic elements in the aerosols was determined using AAS instrument. Size, morphology, and mineralogy of the particles were studied using SEM and EDX spectra. The results indicate that the amount of total suspended particles in upwind, mine district, and downwind sites is 95.5, 463.4 and 287.5 µg/m³, respectively. The concentrations of PM_2.5 in the three locations are 8.9, 134.7, and 51.8 µg/m³, whereas the PM₁₀ contents are 2.9, 74.4, and 15.5 µg/m³, respectively. These observations point to the impact of mining activities on the concentration of aerosols in the local atmosphere. The values of air quality index also show the probable effects of the mining activities on the health of the local populations, especially for allergic peoples. The average concentration of Zn in the samples collected from the mining district (290 µg/kg) is much higher than its value in the upwind sites (27 µg/kg). The highest concentration of As (70 µg/kg), Cd (10 µg/kg), and Pb (3 µg/kg) is in downwind sites, which shows the negative impact of mining activities on the local air quality. Temporally, the highest concentration of the studied elements is recorded in spring season, especially for PM_2.5 collected in downwind stations. Based on the results of SEM and EDX spectra, three groups of minerals, i.e., carbonates, silicates, and sulfides, are present in the aerosol particles, confirming the local source for the aerosols. SEM analyses showed that the aerosol particles with dissimilar chemical composition have different morphologies such as irregular, rounded, elongated, and angular. On the basis of the results, the mining activities in the Angouran Zn–Pb Mine may have various short- and long-term consequences on the public health, especially due to high amount of the finer particles (PM_2.5) and the higher concentration of the potentially toxic elements in PM_2.5 which can penetrate into the lungs.

     

Observation of black carbon aerosol in Beijing, 2003

The objective of this study was to determine the black carbon concentration in Beijing in 2003. The aerosol properties were measured using an Aethalometer and a tapered element oscillating microbalance (TEOM) on the roof of the Physics Building of Peking University (39.99° N, 116.31° E) from July to August 2003 and from November 2003 to January 2004. The average black carbon (BC) concentrations in the summer and winter were 8.80 and 11.4 μg/m³, respectively. During winter, two different cyclone cut offs were installed at the inlet of an aethalometer. The BC mass concentration in TSP, PM₁₀, and PM_2.5 were obtained. The results indicated that in winter aerosol, 90% of BC exited in PM₁₀ and 82.6% of BC exited in PM_2.5. The BC in PM₁₀ accounted for 5.11% of the PM₁₀ mass.     

Development of source profiles and their application in source apportionment of PM<Subscript>2.5</Subscript> in Xiamen,China

Ambient PM_2.5 samples were collected at four sites in Xiamen, including Gulangyu (GLY), Hongwen (HW), Huli (HL) and Jimei (JM) during January, April, July and October 2013. Local source samples were obtained from coal burning power plants, industries, motor vehicles, biomass burning, fugitive dust, and sea salt for the source apportionment studies. The highest value of PM_2.5 mass concentration and species related to human activities (SO₄ ^2–, NO₃ ^–, Pb, Ni, V, Cu, Cd, organic carbon (OC) and elemental carbon (EC)) were found in the ambient samples from HL, and the highest and lowest loadings of PM_2.5 and its components occurred in winter and summer, respectively. The reconstructed mass balance indicated that ambient PM_2.5 consisted of 24% OM (organic matter), 23% sulfate, 14% nitrate, 9% ammonium, 9% geological material, 6% sea salt, 5% EC and 10% others. For the source profiles, the dominant components were OC for coal burning, motor vehicle, biomass burning and sea salt; SO₄ ^2– for industry; and crustal elements for fugitive dust. Source contributions were calculated using a chemical mass balance (CMB) model based on ambient PM_2.5 concentrations and the source profiles. GLY was characterized by high contributions from secondary sulfate and cooking, while HL and JM were most strongly affected by motor vehicle emissions, and biomass burning and fugitive dust, respectively. The CMB results indicated that PM_2.5 from Xiamen is composed of 27.4% secondary inorganic components, 20.8% motor vehicle emissions, 11.7% fugitive dust, 9.9% sea salt, 9.3% coal burning, 5.0% biomass burning, 3.1% industry and 6.8% others.

Open image in new window

     

细颗粒物(PM_(2.5))主要组分模拟溶液对发光细菌的光抑制分析

为明确NH_4~+、 NO_3~-、SO_4~(2-)及金属等组分在水溶性提取液对发光细菌的光抑制过程中所起的作用,参照PM_(2.5)样品提取液浓度,模拟配制与3级以上PM_(2.5)样品提取液中主要组分:硫酸盐、硝酸盐、氨盐相同浓度的溶液,同时选取与PM_(2.5)可溶性提取液发光抑制率相关性较强的铅、锌,配制不同浓度级别模拟溶液,测试各单一组分对发光细菌的发光抑制率及其混合溶液对发光细菌的联合影响效应。基于毒性单位法(TU)、相加指数法(AI)和混合毒性指数法(MTI)评价了混合体系联合影响的作用类型。结果表明,与3~6级PM_(2.5)可溶性提取液中硫酸氨、硫酸氢氨、硝酸氨、硫酸锌和硝酸铅浓度相同的模拟溶液对发光细菌的发光没有抑制作用。不同的评价方法对PM_(2.5)主要组分混合体系联合效应评价结果具有较好的一致性,硫酸氨、硝酸氨、硫酸氢氨混合溶液中,对发光细菌的光抑制均为硫酸氢氨的独立作用,硫酸锌与硝酸铅的混合体系,锌和铅对发光细菌的联合影响效应表现为协同,硫酸氨、硝酸氨、硫酸氢氨与硫酸锌、硝酸铅的多元混合体系呈现协同作用。     

Aktuelle Aerosoltrends an der GAW Globalstation Hohenpeißenberg und ihre Relevanz für Luftreinhaltung und Klima

Aim and Scope

This study was aimed at representing current aerosol trends measured at the GAW global station and their relevance for the present fine dust discussion and a possible impact on climate.

Results and Discussion

1) The intensive GAW measuring program at Hohenpeissenberg covers numerous parameters for the characterization of the physical, optical and chemical characteristics of the atmospheric aerosol. The time series of the number concentration of ultra fine particles with diameters of about 0.004 to 3 μm shows an increase of about 50% since 1995. 2) The introduction of soot particle filters would lower the dust mass only slightly since soot particles from diesel cars only about 8–10% contribute to the dust mass, but about 90% to the number concentration of particles. 3) The single scattering albedo (SSA) is a key parameter determining whether the existing aerosol mixture causes a cooling (negative radiative forcing) or a warming (positive radiative forcing) in the atmosphere. At Hohenpeißenberg the SSA changed from 0.85 to 0.91 in the time period 1999 to 2005, i.e. the regional aerosol as a whole is dominated by scattering rather than absorbing particles.

Conclusion and Perspective

From current aerosol trends at the GAW global station Hohenpeißenberg it was possible to analyze their relevance for air pollution control and possible influences on climate. Dust mass is not a suitable parameter for accessing the contribution of diesel engined vehicles. Measuring the number concentration of particles much more reflects the influence of diesel engined vehicles and also shows, as expected, an upward trend due to a strong increase of the fraction of diesel vehicles in comparison to the total number of cars. Aerosol particles scatter and absorb solar radiation and thus cause a cooling or warming in the atmosphere. Calculated values of the single scattering albedo at Hohenpeissenberg show, that in the initial years the aerosol did not diminish the temperature rise, but rather caused it to increase. Only a data comparison from a global network like GAW can demonstrate, if the results are even representative for the large scale situation.     

Study on particulate matter air pollution,source origin,and human health risk based of PM10 metal content in Volos City,Greece

Investigations on the fluctuation in PM₁₀ air pollution in Volos, a medium-sized industrialized port city in the Mediterranean, are presented for the 5-year period between 2009 and 2014. The levels detected have been examined in relation to legislatively set limits, sampling year, and day of the week. A PM₁₀ spring sampling campaign has been performed in 2014 and metals and other elements in the PM₁₀ mass have been quantified. Source origin has been attempted for the latter sampling campaign and human health risk has been assessed. Results show compliance with the mean annual value of 40 μg m^?3 of 2008/50/EC for the city; however, exceedances of the daily quality standard of 50 μg m^?3 were frequently recorded. Shifts in PM₁₀ concentrations and in contributing sources have been recorded; nevertheless, longer duration data series are needed for safe deductions. Element measurements have enabled source identification for early summer of 2014, with Earth's crust minerals and anthropogenic sources being the main factors. Cumulative non-carcinogenic risk may exceed the threshold value of 1. Possible involvement of sea salt aerosol and desert dust long-range transport has also been assessed. These results may furnish databases on PM pollution of Greek cities as well as other Mediterranean urban centers with similar characteristics.     

Study of atmospheric electrical conductivity,SO2, NO2, aerosols SPM (>10 μ) and RSPM (<10 μ) in Mysore city,India

It is well known that atmospheric electrical conductivity is mainly due to the presence of small ions. Near the surface of the earth, radon and its daughter products predominantly produce small ions. In the presence of aerosol particles, the small ion concentration is reduced due to attachment of small ions to aerosol particles which decreases mobility and conductivity in the atmosphere. The ion pair production rate is estimated from the measured radon and its progeny concentrations and correlated with electrical conductivity of the atmosphere. Measurement of concentrations of suspended particulate matter (SPM), SO₂, and NO₂ of air was also carried out. Data showed that reduced electrical conductivity was related to concentration of airborne SPM.     

Particle size distributions, PM2.5 concentrations and water-soluble inorganic ions in different public indoor environments: a case study in Jinan, China

In this study, we collected particles with aerodynamic diameter ?2.5 μm (PM_2.5) from three different public indoor places (a supermarket, a commercial office, and a university dining hall) in Jinan, a medium-sized city located in northern China. Water-soluble inorganic ions of PM_2.5 and particle size distributions were also measured. Both indoor and outdoor PM_2.5 levels (102.3–143.8 μg·m^?3 and 160.2–301.3 μg·m^?3, respectively) were substantially higher than the value recommended by the World Health Organization (25 μg·m^?3), and outdoor sources were found to be the major contributors to indoor pollutants. Diurnal particle number size distributions were different, while the maximum volume concentrations all appeared to be approximately 300 nm in the three indoor locations. Concentrations of indoor and outdoor PM_2.5 were shown to exhibit the same variation trends for the supermarket and dining hall. For the office, PM_2.5 concentrations during nighttime were observed to decrease sharply. Among others, SO ₄ ^2? , NH ₄ ⁺ and NO ₃ ^? were found to be the dominant water-soluble ions of both indoor and outdoor particles. Concentrations of NO ₃ ^? in the supermarket and office during the daytime were observed to decrease sharply, which might be attributed to the fact that the indoor temperature was much higher than the outdoor temperature. In addition, domestic activities such as cleaning, water usage, cooking, and smoking also played roles in degraded indoor air quality. However, the results obtained here might be negatively impacted by the small number of samples and short sampling durations.