Separation and recovery of carbon dioxide by a membrane flash process

A novel process for carbon dioxide (CO₂) separation, which was named a membrane flash process, was developed to realize an energy-saving technology and to substitute it for a conventional regenerator. The electric energy for CO₂ recovery in a membrane flash process using aluminum oxide and diethanolamine was lower than the thermal energy of the conventional chemical absorption process. Flashing at elevated temperature by the low temperature energy significantly reduced the electric energy and required much less membrane area. This process has potentiality of low cost capture of CO₂ when the low temperature energy, which is not available for other purposes, can be utilized to elevate flashing temperature.     

Thermodynamic analysis on post-combustion CO2 capture of natural-gas-fired power plant

A chemical absorption, post-combustion CO₂ capture unit is simulated and an exergy analysis has been conducted, including irreversibility calculations for all process units. By pinpointing major irreversibilities, new proposals for efficient energy integrated chemical absorption process are suggested. Further, a natural-gas combined-cycle power plant with a CO₂ capture unit has been analyzed on an exergetic basis. By defining exergy balances and black-box models for plant units, investigation has been made to determine effect of each unit on the overall exergy efficiency. Simulation of the chemical absorption plant was done using UniSim Design software with Amines Property Package. For natural-gas combined-cycle design, GT PRO software (Thermoflow, Inc.) has been used. For exergy calculations, spreadsheets are created with Microsoft Excel by importing data from UniSim and GT PRO. Results show the exergy efficiency of 21.2% for the chemical absorption CO₂ capture unit and 67% for the CO₂ compression unit. The total exergy efficiency of CO₂ capture and compression unit is 31.6%.     

Techno-economic study of CO2 capture from natural gas based hydrogen plants

Canadian oil sands are considered to be the second largest oil reserves in the world. However, the upgrading of bitumen from oil sands to synthetic crude oil (SCO) requires nearly ten times more hydrogen (H₂) than conventional crude oils. The current H₂ demand for oil sands operations is met mostly by steam reforming of natural gas (SMR). The future expansion of oil sands operations is likely to quadruple the demand of H₂ for oil sand operations in the next decade.This paper presents modified process schemes that capture CO₂ at minimum energy penalty in modern SMR plants. The approach is to simulate a base case H₂ plant without CO₂ capture and then look for the best operating conditions that minimize the energy penalty associated with CO₂ capture while maximizing H₂ production. The two CO₂ capture schemes evaluated in this study include a membrane separation process and the monoethanolamine (MEA) absorption process. A low energy penalty is observed when there is lower CO₂ production and higher steam production. The process simulation results show that the H₂ plant with CO₂ capture has to be operated at lower steam to carbon ratio (S/C), higher inlet temperature of the SMR and lower inlet temperatures for the water gas-shift (WGS) converters to attain lowest energy penalty. Also it is observed that both CO₂ capture processes, the membrane process and the MEA absorption process, are comparable in terms of energy penalty and CO₂ avoided when both are operated at conditions where lowest energy penalty exists.     

Exploring the potential for improvement of the energy performance of coal fired power plants with post-combustion capture of carbon dioxide

The application of post-combustion capture (PCC) processes in coal fired power stations can result in large reductions of the CO₂-emissions, but the consequential decrease in generation efficiency is an important draw-back. The leading PCC technology is based on chemical absorption processes as this technology is the one whose scale-up status is closest to full-scale capture in power plants. The energy performance of this process is analysed in this contribution. The analysis shows that the potential for improvement of the energy performance is quite large. It is demonstrated that further development of the capture technology and the power plant technology can lead to generation efficiencies for power plants with 90% CO₂ capture which are equivalent to the current generation efficiencies without CO₂ capture, i.e. 0.4 (HHV), leading to an additional resource consumption of 16%. These improvements are possible throughout a combined improvement for the capture process and power generation processes.     

Techno-Economic Study of CO2 Capture from an Existing Cement Plant Using MEA Scrubbing

Carbon dioxide is the major greenhouse gas responsible for global warming. Man-made CO₂ emissions contribute approximately 63% of greenhouse gases and the cement industry is responsible for approximately 5% of CO₂ emissions emitting nearly 900 kg of CO₂ per 1000 kg of cement. CO₂ from a cement plant was captured and purified to 98% using the monoethanolamine (MEA) based absorption process. The capture cost was $51 per tonne of CO₂ captured, representing approximately 90% of total cost. Steam was the main operating cost representing 39% of the total capture cost. Switching from coal to natural gas reduces CO₂ emissions by about 18%. At normal load, about 36 MW of waste heat is available for recovery to satisfy the parasitic heat requirements of MEA process; however, it is very difficult to recover.     

Gas conditioning—The interface between CO2 capture and transport

Gas conditioning is commonly referred to as the required processing for a produced natural gas to achieve transport and sales specifications. In this paper, gas conditioning as the processing required in the interface between CO₂ capture and transport is studied for nine different natural gas fired power plant concepts and three different CO₂ transport processes. Conditioning processes for both pipeline and ship transport are described and an enhanced process for volatile removal is developed. The energy requirement for the conditioning processes is normally between 90 and 120 kWh/tonne CO₂; however, this depends on the pressure and composition of the captured CO₂-rich stream. The loss of CO₂ in the water purge is small for most capture processes. The waste streams from the gas conditioning processes can contain large amounts of CO₂ and should therefore be further processed or reintroduced at an appropriate point upstream in the capture or gas conditioning process if possible. The integration benefit may vary depending on the composition of the CO₂-rich stream. It could be particularly interesting for processes with “innovative reactors” (membranes, sorbents, chemical looping) to integrate CO₂ capture and gas conditioning.     

Integration of CO2 capture unit using single- and blended-amines into supercritical coal-fired power plants: Implications for emission and energy management

This work provides the essential information and approaches for integration of carbon dioxide (CO₂) capture units into power plants, particularly the supercritical type, so that energy utilization and CO₂ emissions can be well managed in the subject power plants. An in-house model, developed at the University of Regina, Canada, was successfully used for simulating a 500 MW supercritical coal-fired power plant with a post-combustion CO₂ capture unit. The simulations enabled sensitivity and parametric study of the net efficiency of the power plant, the coal consumption rate, and the amounts of CO₂ captured and avoided. The parameters of interest include CO₂ capture efficiency, type of coal, flue gas delivery scheme, type of amine used in the capture unit, and steam pressure supplied to the capture unit for solvent regeneration. The results show that the advancement of MEA-based CO₂ capture units through uses of blended monoethanolamine–methyldiethanolamine (MEA–MDEA) and split flow configuration can potentially make the integration of power plant and CO₂ capture unit less energy intensive. Despite the increase in energy penalty, it may be worth capturing CO₂ at a higher efficiency to achieve greater CO₂ emissions avoided. The flue gas delivery scheme and the steam pressure drawn from the power plant to the CO₂ capture unit should be considered for process integration.     

Designing a supercritical steam cycle to integrate the energy requirements of CO2 amine scrubbing

Absorption by chemical solvents combined with CO₂ long-term storage appears to offer interesting and commercial applicable CO₂ capture technology. However one of the main disadvantages is related to the large quantities of heat required to regenerate the amine solvent that means an important power plant efficiency penalty. Different studies have analyzed alternatives to reduce the heat duty on the reboiler and the thermal integration requirements on existing power cycles. In these studies integration principles have been well set up, but there is a lack of information about how to achieve an integrated design and the thermal balances of the modified cycle flowsheet. This paper proposes and provides details about a set of modifications of a supercritical steam cycle to overcome the energy requirements through energetic integration with the aim of reducing the efficiency and power output penalty associated with CO₂ capture process. Modifications include a new designed low-pressure heater flowsheet to take advantage of the CO₂ compression cooling for postcombustion systems and integration of amine reboiler into a steam cycle. It has been carried out several simulations in order to obtain power plant performance depending on sorbent regeneration requirements.     

Development of novel absorbents for CO2 capture from blast furnace gas

In order to establish energy-saving technology for CO₂ capture from blast furnace gas, novel absorbents were developed in the laboratory and evaluated at a 1 t_CO2/d test plant. At first, CO₂ absorption and desorption behaviors of single-component amine solvents for simulated blast furnace gas (CO₂/N₂ = 20%/80%) were investigated through a screening test using a small scrubbing bottle. These amine solvents were additionally analyzed using nuclear magnetic resonance (¹³C NMR) spectroscopy and reaction calorimetry. The results of the laboratory experiments showed that there was a trade-off between absorption rate and enthalpy of absorption but some absorbents had unique features. For example, 2-isopropylaminoethanol (IPAE) had high absorption rate and small enthalpy of absorption. Then, new IPAE-based amine solvents (RITE solvents: RITE-A and RITE-B) were formulated and evaluated at the 1 t_CO2/d test plant. CO₂ regeneration energies of the RITE solvents were 3.3 and 3.1 GJ/t_CO2, respectively. With certain process conditions and plant specifications optimized, RITE-B was estimated to have the potential to achieve 2.5 GJ/t_CO2.     

Numerical parametric study on CO2 capture by indirect thermal swing adsorption

Post-combustion CO₂ capture remains one of the most-challenging issue to lower CO₂ emissions of existing power plants or heavy industry installations because of strong economy and energy efficiency aspects. The major issue comes from CO₂ dilution (4% for NGCC and 14% for PC) and the high flow rates to be treated. Furthermore, CO₂ purity has to be higher than 95% with recovery at 90%, to match the transportation/injection requirements.The MEA absorption process remains the reference today but its energy consumption (about 3 MJ/kg_CO2) and the amine consumption are still challenging drawbacks.The interest of CO₂ capture by indirect TSA (Temperature Swing Adsorption) was demonstrated experimentally in a previous work. The aim of this paper is to present the results of a numerical parametric study. Two main parameters are explored: the desorption temperature (100–200 °C) and the purge flow rate (0.1–0.5 Ndm³ min⁻¹). Four performance indicators are evaluated: CO₂ purity, recovery, productivity and specific energy consumption.Results show that purity above 95% can be achieved. Keeping the 95% target, it is possible to achieve recovery at 81% with productivity at 57.7 g_CO2/kg_ads h and a specific energy consumption of 3.23 MJ/kg_CO2, which is less than for the reference MEA process.Comparison with other adsorption processes exhibits that this process has good potential especially since some improvements are still expected from further research.     

Power generation with CO2 capture: Technology for CO2 purification

The goal of this paper is to find methodologies for removing a selection of impurities (H₂O, O₂, Ar, N₂, SO_x and NO_x) from CO₂ present in the flue gas of two oxy-combustion power plants fired with either natural gas (467 MW) or pulverized fuel (596 MW). The resulting purified stream, containing mainly CO₂, is assumed to be stored in an aquifer or utilized for enhanced oil recovery (EOR) purposes. Focus has been given to power cycle efficiency i.e.: work and heat requirements for the purification process, CO₂ purity and recovery factor (kg of CO₂ that is sent to storage per kg of CO₂ in the flue gas). Two different methodologies (here called Case I and Case II) for flue gas purification have been developed, both based on phase separation using simple flash units (Case I) or a distillation column (Case II). In both cases purified flue gas is liquefied and its pressure brought to 110 atm prior to storage.Case I: A simple flue gas separation takes place by means of two flash units integrated in the CO₂ compression process. Heat in the process is removed by evaporating the purified liquid CO₂ streams coming out from both flashes. Case I shows a good performance when dealing with flue gases with low concentration of impurities. CO₂ fraction after purification is over 96% with a CO₂ recovery factor of 96.2% for the NG-fired flue gas and 88.1% for the PF-fired flue gas. Impurities removal together with flue gas compression and liquefaction reduces power plant output of 4.8% for the NG-fired flue gas and 11.6% for the PF-fired flue gas. The total amount of work requirement per kg stored CO₂ is 453 kJ for the NG-fired flue gas and 586 kJ for the PF-fired flue gas.Case II: Impurities are removed from the flue gas in a distillation column. Two refrigeration loops (ethane and propane) have been used in order to partially liquefy the flue gas and for heat removal from a partial condenser. Case II can remove higher amounts of impurities than Case I. CO₂ purity prior to storage is over 99%; CO₂ recovery factor is somewhat lower than in Case I: 95.4% for the NG-fired flue gas and 86.9% for the PF-fired flue gas, reduction in the power plant output is similar to Case I.Due to the lower CO₂ recovery factor the total amount of work per kg stored CO₂ is somewhat higher for Case II: 457 kJ for the NG-fired flue gas and 603 kJ for the PF-fired flue gas.     

Optimization of a membrane process for CO2 capture in the steelmaking industry

Three different types of membranes were experimentally evaluated for CO₂ recovery from blast furnace effluents: semi-commercial adsorption selective carbon membranes, in-house tailored carbon molecular sieving membranes, and fixed site carrier (FSC) membranes with amine groups in the polymer backbone for active transport of CO₂. In the single gas experiments the FSC membranes showed superior selectivity for CO₂ over the other relevant gases (CO, N₂ and H₂) and high CO₂ permeance (productivity). In addition, it is easy to process and handle, relatively inexpensive to produce and the water in the feed gas is an advantage rather than a problem, since the membrane must be humidified during operation. Based on these experiments a simulation study of a full scale process was performed. The technology showed notable low energy cost, even when converted to the thermal equivalent. Total costs for the CO₂ recovery unit (CO₂ prepared for pipeline transport) were estimated to be in the range 15.0–17.5 €/tonnes CO₂.     

Exergy analysis as a tool for the integration of very complex energy systems: The case of carbonation/calcination CO2 systems in existing coal power plants

A common characteristic of carbon capture and storage systems is the important energy consumption associated with the CO₂ capture process. This important drawback can be solved with the analysis, synthesis and optimization of this type of energy systems. The second law of thermodynamics has proved to be an essential tool in power and chemical plant optimization. The exergy analysis method has demonstrated good results in the synthesis of complex systems and efficiency improvements in energy applications.In this paper, a synthesis of pinch analysis and second law analysis is used to show the optimum window design of the integration of a calcium looping cycle into an existing coal power plant for CO₂ capture. Results demonstrate that exergy analysis is an essential aid to reduce energy penalties in CO₂ capture energy systems. In particular, for the case of carbonation/calcination CO₂ systems integrated in existing coal power plants, almost 40% of the additional exergy consumption is available in the form of heat. Accordingly, the efficiency of the capture cycle depends strongly on the possibility of using this heat to produce extra steam (live, reheat and medium pressure) to generate extra power at steam turbine. The synthesis of pinch and second law analysis could reduce the additional coal consumption due to CO₂ capture 2.5 times, from 217 to 85 MW.     

CO2 capture and storage from a bioethanol plant: Carbon and energy footprint and economic assessment

Biomass energy and carbon capture and storage (BECCS) can lead to a net removal of atmospheric CO₂. This paper investigates environmental and economic performances of CCS retrofit applied to two mid-sized refineries producing ethanol from sugar beets. Located in the Region Centre France, each refinery has two major CO₂ sources: fermentation and cogeneration units. “carbon and energy footprint” (CEF) and “discounted cash flow” (DCF) analyses show that such a project could be a good opportunity for CCS early deployment. CCS retrofit on fermentation only with natural gas fired cogeneration improves CEF of ethanol production and consumption by 60% without increasing much the non renewable energy consumption. CCS retrofit on fermentation and natural gas fired cogeneration is even more appealing by decreasing of 115% CO₂ emissions, while increasing non renewable energy consumption by 40%. DCF shows that significant project rates of return can be achieved for such small sources if both a stringent carbon policy and direct subsidies corresponding to 25% of necessary investment are assumed. We also underlined that transport and storage cost dilution can be realistically achieved by clustering emissions from various plants located in the same area. On a single plant basis, increasing ethanol production can also produce strong economies of scale.     

CO2 capture from coal-fired power plants based on sodium carbonate slurry; a systems feasibility and sensitivity study

In this work the feasibility of a CO₂ capture system based on sodium carbonate–bicarbonate slurry and its integration with a power plant is studied. The results are compared to monoethanolamine (MEA)-based capture systems. Condensing power plant and combined heat and power plant with CO₂ capture is modelled to study the feasibility of combined heat and power plant for CO₂ capture.Environmental friendly sodium carbonate would be an interesting chemical for CO₂ capture. Sodium carbonate absorbs CO₂ forming sodium bicarbonate. The low solubility of sodium bicarbonate is a weak point for the sodium carbonate based liquid systems since it limits the total concentration of carbonate. In this study the formation of solid bicarbonate is allowed, thus forming slurry, which can increase the capacity of the solvent. With this the energy requirement of stripping of the solvent could potentially be around 3.22 MJ/kg of captured CO₂ which is significantly lower than with MEA based systems which typically have energy consumption around 3.8 MJ/kg of captured CO₂.Combined heat and power plants seem to be attractive for CO₂ capture because of the high total energy efficiency of the plants. In a condensing power plant the CO₂ capture decreases directly the electricity production whereas in a combined heat and power plant the loss can be divided between district heat and electricity according to demand.     

The potential contribution of sustainable waste management to energy use and greenhouse gas emission reduction in the Netherlands

Future limitations on the availability of selected resources stress the need for increased material efficiency. In addition, in a climate-constrained world the impact of resource use on greenhouse gas emissions should be minimized. Waste management is key to achieve sustainable resource management. Ways to use resources more efficiently include prevention of waste, reuse of products and materials, and recycling of materials, while incineration and anaerobic digestion may recover part of the embodied energy of materials. This study used iWaste, a simulation model, to investigate the extent to which savings in energy consumption and CO₂ emissions can be achieved in the Netherlands through recycling of waste streams versus waste incineration, and to assess the extent to which this potential is reflected in the LAP2 (currently initiated policy). Three waste streams (i.e. household waste, bulky household waste, and construction and demolition waste) and three scenarios compare current policy to scenarios that focus on high-quality recycling (Recycling+) or incineration with increased efficiency (Incineration+). The results show that aiming for more and high-quality recycling can result in emission reductions of 2.3 MtCO₂ annually in the Netherlands compared to the reference situation in 2008. The main contributors to this reduction potential are found in optimizing the recycling of plastics (PET, PE and PP), textiles, paper, and organic waste. A scenario assuming a higher energy conversion efficiency of the incinerator treating the residual waste stream, achieves an emission reduction equivalent to only one third (0.7 MtCO₂/year) of the reduction achieved in the Recycling+ scenario. Furthermore, the results of the study show that currently initiated policy only partially realizes the full potential identified. A focus on highest quality use of recovered materials is essential to realize the full potential energy and CO₂ emission reduction identified for the Netherlands. Detailed economic and technical analyses of high quality recycling are recommended to further evaluate viable integrated waste management policies.     

Integration of post-combustion capture and storage into a pulverized coal-fired power plant

Post-combustion CO₂ capture and storage (CCS) presents a promising strategy to capture, compress, transport and store CO₂ from a high volume–low pressure flue gas stream emitted from a fossil fuel-fired power plant. This work undertakes the simulation of CO₂ capture and compression integration into an 800 MW_e supercritical coal-fired power plant using chemical process simulators. The focus is not only on the simulation of full load of flue gas stream into the CO₂ capture and compression, but also, on the impact of a partial load. The result reveals that the energy penalty of a low capture efficiency, for example, at 50% capture efficiency with 10% flue gas load is higher than for 90% flue gas load at the equivalent capture efficiency by about 440 kWh_e/tonne CO₂. The study also addresses the effect of CO₂ capture performance by different coal ranks. It is found that lignite pulverized coal (PC)-fired power plant has a higher energy requirement than subbituminous and bituminous PC-fired power plants by 40.1 and 98.6 MW_e, respectively. In addition to the investigation of energy requirement, other significant parameters including energy penalty, plant efficiency, amine flow rate and extracted steam flow rate, are also presented. The study reveals that operating at partial load, for example at half load with 90% CO₂ capture efficiency, as compared with full load, reduces the energy penalty, plant efficiency drop, amine flow rate and extracted steam flow rate by 9.9%, 24.4%, 50.0% and 49.9%, respectively. In addition, the effect of steam extracted from different locations from a series of steam turbine with the objective to achieve the lowest possible energy penalty is evaluated. The simulation shows that a low extracted steam pressure from a series of steam turbines, for example at 300 kPa, minimizes the energy penalty by up to 25.3%.     

Modeling CO2 capture with aqueous monoethanolamine

Hilliard completed several thermodynamic models in Aspen Plus^® for modeling CO₂ removal with amine solvents, including MEA–H₂O–CO₂. This solvent was selected to make a system model for CO₂ removal by absorption/stripping. Both the absorber and the stripper used RateSep? to rigorously calculate mass transfer rates. The accuracy of the new model was assessed using a recent pilot plant run with 35 wt.% (9 m) MEA. Absorber loading and removal were predicted within 6%, and the temperature profile was approached within 5 °C. An average 3.8% difference between measured and calculated values was achieved in the stripper. A three-stage flash configuration which efficiently utilizes solar energy was developed. It reduces energy use by 6% relative to a simple stripper. Intercooling was used to reach 90% removal in the absorber at these optimized conditions.     

Electricity systems with near-zero emissions of CO2 based on wind energy and coal gasification with CCS and hydrogen storage

Emissions from electricity generation will have to be reduced to near-zero to meet targets for reducing overall greenhouse gas emissions. Variable renewable energy sources such as wind will help to achieve this goal but they will have to be used in conjunction with other flexible power plants with low-CO₂ emissions. A process which would be well suited to this role would be coal gasification hydrogen production with CCS, underground buffer storage of hydrogen and independent gas turbine power generation. The gasification hydrogen production and CO₂ capture and storage equipment could operate at full load and only the power plants would need to operate flexibly and at low load, which would result in substantial practical and economic advantages. This paper analyses the performances and costs of such plants in scenarios with various amounts of wind generation, based on data for power demand and wind energy variability in the UK. In a scenario with 35% wind generation, overall emissions of CO₂ could be reduced by 98–99%. The cost of abating CO₂ emissions from the non-wind residual generation using the technique proposed in this paper would be less than 40% of the cost of using coal-fired power plants with integrated CCS.     

Quantitative evaluation of the chilled-ammonia process for CO2 capture using thermodynamic analysis and process simulation

There is strong world-wide interest in developing new and improved processes for post-combustion capture of CO₂, often using chemical absorption. Developers of new processes make positive claims for their proposals in terms of low energy consumption, but these are usually difficult to validate. This paper demonstrates that rigorous application of thermodynamic analysis and process simulation provides a powerful way to quantitatively estimate the energy requirements of CO₂-capture processes by applying the methodology to the analysis and evaluation of the chilled-ammonia process.