Use of constructed wetland systems with Arundo and Sarcocornia for polishing high salinity tannery wastewater

Treatment of tannery wastewater is problematic due to high and variable concentrations of complex pollutants often combined with high salinity levels. Two series of horizontal subsurface flow constructed wetlands (CWs) planted with Arundo donax and Sarcocornia fruticosa were set up after a conventional biological treatment system operating at a tannery site. The aim of the CWs was polishing organics and nitrogen from the high salinity effluent (2.2-6.6?g Cl(-)?L(-1)). Both plant species established and grew well in the CW. Arundo, however, had more vigorous growth and a higher capacity to take up nutrients. The CWs were efficient in removing COD and BOD(5) with removal efficiencies varying between 51 and 80% for COD (inlet: 68-425?mg?L(-1)) and between 53 and 90% for BOD(5) (inlet: 16-220?mg?L(-1)). Mass removal rates were up to 615?kg COD ha(-1)?d(-1) and 363 BOD(5) kg?ha(-1)?d(-1). Removal efficiencies were 40-93% for total P, 31-89% for NH(4)(+) and 41-90% for Total Kjeldahl Nitrogen. CW systems planted with salt tolerant plant species are a promising solution for polishing saline secondary effluent from the tannery industry to levels fulfilling the discharge standards.     

Modelling Escherichia coli concentration in a wastewater reservoir using an operational parameter MRT%FE and first order kinetics

The operational parameter MRT%FE, representing the mean residence time of different ages fractions of effluent within a completely mixed reactor, was evaluated and integrated with first order kinetics. The parameter was used to model Escherichia coli concentrations in a municipal wastewater reservoir managed under different operating conditions (continuous and discontinuous). The study was conducted during 2004-2005 in a reservoir receiving effluents from the activated sludge treatment plant of Caltagirone (Eastern Sicily - Italy). The analytical approach is applied to the hydraulic state variables of the system (daily stored volumes, inlet and outlet flows), and the physical-chemical (pH, temperature, EC, TSS, BOD(5), COD) and bacteriological wastewater parameters (E. coli, FC, FS). In order to evaluate the reliability of the proposed approach, predicted E. coli concentrations within the reservoir were compared with measured ones by the correlation coefficient, F-test and Sperman's index. The study included the evaluation of die-off coefficient K(T) (d(-1)), light extinction coefficient K (m(-1)) and their relationships with climatic factors. Results of the study confirm that E. coli removal is related to the fractions of fresh effluent remaining each day within the reservoir with MRT%FE of about 5-8d, significantly lower than the nominal detention time (about 27d). The E. coli die-off coefficient (K(T)) was higher during system discontinuous operations and correlated with incident solar radiation and water temperature.     

单户型家庭生活污水盆景式处理研究

单户型家庭生活污水盆景式处理是以人工湿地为基础的分散式废水处理方法。通过接近1年的试验对其净水效果进行研究,结果表明,它对化学需氧量（CODCr）、生物需氧量（BOD5）、氨氮（NH3-N）、总磷（TP）、总固体悬浮物（TSS）的去除率可分别达到92.72%、96.28%、79.06%、85.11%、95.83%。出水水质分别达到33.8mg/L、19.2mg/L、0.8 mg/L、0.7 mg/L、8 mg/L,基本符合国家一级排放标准,部分指标如BOD5、NH3-N等甚至可以达到或优于城市生活杂用水水质标准。同时它也可以作为室内盆景用水,起到美化环境净化空气的作用。     

Flavour Industry Wastewater Management Case Study

Summary This study is carried out to propose an appropriate treatment technology for wastewater discharged from a flavor production factory. Industrial wastewater discharged from this factory ranges between 50–70 m³/d with an average value of 60 m³/d. The major source of pollution in this factory is due to cleaning of the vessels therefore the treatment has been carried out on the end-of pipe wastewater. The wastewater is characterized by high values of COD, BOD, TSS and Oil and grease 4646, 2298, 1790 and 626 mg/l respectively. Primary sedimentation of the wastewater for four hours reduced the COD, BOD, TSS and Oil and grease by 43, 47, 80 and 74%, respectively. For the treatment of the produced wastewater, the biological treatment process such as activated sludge, rotating biological contactor (RBC), up-flow anaerobic sludge bed reactor (UASB) have been selected. The results from each treatment process proved to be efficient for the treatment of such wastewater. The treated wastewater characteristics are in compliance with the Egyptian law which regulates the discharge of industrial wastewater to the sewerage system. The RBC was selected and installed by the factory as it has the advantage of low operating and maintenance costs. The factory RBC performance was monitored; characteristics of the treated effluent in terms of oil and grease, COD, BOD and TSS were 27, 362, 139 and 95 mg/l, respectively.     

Investigating the quantitative and qualitative status of effluent in the wastewater treatment plant in Iran Central Iron Ore

The aim of present study was to investigate the quality of the produced effluent from different units of the Iran Central Iron Ore in Bafq city and comparison of effluent with the standards. This study presents the physicochemical and biological parameters data of effluent of three Sequencing batch reactors (SBR) with a capacity of 160 m³?d^?1. Most common parameters include pH, total suspended solids (TSS), total nitrogen (TN), total phosphorus (TP), biochemical oxygen demand (BOD₅), chemical oxygen demand (COD), heavy metals, and total coliforms and fecal coliforms as biological indicators. Then, for each SBR system, the average of each parameter was determined, and results were compared with the standard recommended by the Iranian Environmental Protection Agency. Based on the results, some of the parameters, including BOD₅, COD, and TSS in the wastewater treatment plant (WWTP) effluent, are higher than the permitted amount for discharge to the surface water. Considering the BOD₅, COD, and TSS concentration in WWTPs, the treated wastewater is only suitable for agricultural and irrigation use. Therefore, wastewater produced by Iran Central Iron Ore Co. will need additional treatment to achieve standard quality of water before discharge in surface water and adsorbent well.     

Performance and modeling studies of rotating biological contactor for treatment of vegetable oil wastewater

This study focuses on a lab-scale rotating biological contactor (RBC) treating vegetable oil wastewater with high BOD and COD. The fabricated RBC was checked for efficiency in degrading polluted wastewater under different operating conditions. The maximum removal efficiencies for BOD and COD were 95.75% and 89%, respectively. This high removal percentage was obtained with 30% submergence of 10 discs rotating at 8 rpm. For the first time, bio-kinetic models were applied to the experimental results for vegetable oil wastewater. The best fit was obtained with the modified Stover-Kincannon and Grau model. The saturation constant (K_s) values were 1.872 and 3.024 g/L/d for BOD and COD, respectively, for the modified Stover-Kincannon and Grau model. For the Grau second-order model, the saturation constant was 1.416 and 3.744 g/L/d for BOD and COD, respectively. The predicted effluent BOD and COD values of the modified Stover–Kincannon model fitted almost exactly with the experimental values. This clearly predicts that this model can be best used to predict effluent BOD and COD concentration in a Rotating Biological contactor treating vegetable oil wastewater. The kinetic parameters determined in this study can be used to improve the design and operation of continuous mode RBC systems.     

Anaerobic/aerobic treatment of meat processing wastewater

The meat processing industry is believed to produce highly polluted wastewater. Analysis of such wastewater indicated that the waste was highly contaminated with organic compounds as indicated by COD (1544mgO2l–1), BOD (646mgO2l–1), and TSS (1155 mgl–1). Moreover, oil and grease concentrations reached 144mgl–1 treatment of raw wastewater using Upflow Anaerobic Sludge Blanket (UASB) followed by Rotating Biological Contactors (RBC) was studied. Efficiency of the UASB for the removal of CODtotal, BODtotal, TSS, and oil and grease was 56%, 56%, 85%, and 58%, respectively. The quality of the UASB effluent barely complies with the regulatory standards for discharging wastewater into the sewerage network. UASB effluent was subjected for further treatment using a RBC unit to improve the quality of the treated effluent for reuse in irrigation purposes. Residual COD, BOD, TSS, and oil and grease, following RBC, was 132mgO2l–1, 40mgO2l–1, 44mgl–1, and 10mgl–1 respectively. The overall efficiency of the treatment units provided good quality effluent. The overall percentage removal of COD, BOD, TSS, and oil and grease was 91.5%, 94%, 96%, and 91%, respectively. Based on the quality of the treated effluent and guidelines recommended for wastewater reuse, it may be concluded that a slight to moderate restricted irrigation is applicable to reuse the treated effluent in the green belt around the factory. Disinfection should be applied to ensure the safety of such a process.     

Use of artificial neural network black-box modeling for the prediction of wastewater treatment plants performance

A reliable model for any wastewater treatment plant is essential in order to provide a tool for predicting its performance and to form a basis for controlling the operation of the process. This would minimize the operation costs and assess the stability of environmental balance. This process is complex and attains a high degree of nonlinearity due to the presence of bio-organic constituents that are difficult to model using mechanistic approaches. Predicting the plant operational parameters using conventional experimental techniques is also a time consuming step and is an obstacle in the way of efficient control of such processes. In this work, an artificial neural network (ANN) black-box modeling approach was used to acquire the knowledge base of a real wastewater plant and then used as a process model. The study signifies that the ANNs are capable of capturing the plant operation characteristics with a good degree of accuracy. A computer model is developed that incorporates the trained ANN plant model. The developed program is implemented and validated using plant-scale data obtained from a local wastewater treatment plant, namely the Doha West wastewater treatment plant (WWTP). It is used as a valuable performance assessment tool for plant operators and decision makers. The ANN model provided accurate predictions of the effluent stream, in terms of biological oxygen demand (BOD), chemical oxygen demand (COD) and total suspended solids (TSS) when using COD as an input in the crude supply stream. It can be said that the ANN predictions based on three crude supply inputs together, namely BOD, COD and TSS, resulted in better ANN predictions when using only one crude supply input. Graphical user interface representation of the ANN for the Doha West WWTP data is performed and presented.     

利用生态池净化玉泉景点富营养化水的研究

在人工湿地的基础上建立生态池，来净化杭州植物园玉泉观鱼景点观鱼池富营养化水质。结果表明该生态池在每年的不同季度内对总氮（TN）、氨氮（NH3-N）、总磷（TP）、化学需氧量（CODMn）、五日生化需氧量（BOD5）、溶解氧（DO）、浊度（TURB）、电导率（COND）均有较好的改善和净化效果，对硝态氮（NO3-N）的净化能力稍弱；总氮和氨氮的去除率在夏季最高，分别达到26．6％和87．7％，总磷在春季的去除率最高，为56．3％，硝态氮、CODMn和BOD5在秋季去除率最高，分别为8．05％、65．9％和73．9％。生态池的净化出水水质略低于地下水，但可以替代地下水来给养鱼池换水，为解决景区富营养化水质提供了一个好的途径。     

工业园区污水处理工艺的运行及完善探讨

本文对某工业园区的综合废水处理工艺开展了连续两年的运行调查,进行了其工艺完善及提标改造的技术探讨。研究表明,改造前该污水处理装置的出水COD、BOD5、总磷、SS均能达到排放标准,而唯独出水氨氮处理效果差,难以达到一级排放标准要求。通过增设预处理水解装置、生物氧化装置导流墙容积比改进、生物塘深度处理工艺完善后,能够保证出水氨氮的处理效果且能达到一级A排放标准。     

硫磺回收装置脱硫废液处理的试验研究

采用将脱硫废液与炼油废水按比例混合之后对其进行处理的方法,通过批式试验,考查混合废液的BOD5/COD指标及其COD、NH3-N、S2-的去除率。筛选合适的混合液配比,分别对500︰1和800︰1的混合废液进行了模型试验,分析了COD去除效果。结果表明:800︰1的混合废液在10d之后,出水COD为134mg/L,达到了《污水综合排放标准》(GB8978—1996)二级标准要求。最终确定炼油废水与脱硫废液混合的合适比例应不低于800︰1。     

微生物菌剂在酿酒废水处理中的应用研究

采用厌氧－好氧工艺,结合微生物菌剂对酿酒废水进行了处理研究。进水CODCr浓度可达到8,456.3-22,442.0mg/L,BOD55,040.0-9.557.1mg/L,pH3-4,可不调pH,采用微生物菌剂接种可启动厌氧反应器,COD有机负荷最高达到10.2gCOD/Ld,COD去除率稳定在91－95％,BOD去除率90－94％,出水pH6.6-7.1,出水CODCr在2,000mg/L以下,BOD5800mg/L以下。厌氧污泥可全部颗粒化。好氧处理系统中接种微生物菌剂,曝气10－12小时,可保证出水中CODCr在230mg/L以下,甚至直接达到国家一级排放标准。微生物菌剂的应用是取得该处理效果的关键。     

Performance assessment of a wastewater treatment plant producing effluent for irrigation in Egypt

A conventional activated sludge treatment facility was the subject of this study. The assessment was directed at determining the characteristics of the raw wastewater, the quality of the treated effluent and the efficiency of the various treatment units. Furthermore, the water quality along the effluent irrigation canal was monitored. The assessment of the quality of the treated effluent for irrigation is based on the guidelines established by the World Health Organization and the Egyptian decree 9/89 for the use of wastewater in agriculture. The results of the study indicated that the concentration of the raw wastewater was considered moderate. The mean values of the COD (Chemical Oxygen Demand), BOD (Biological Oxygen Demand) and total suspended solids (TSS) were around 250, 102 and 142 mg l–1, respectively. This was attributed to the high quantities of wastewater from industrial sources. The overall efficiency of the treatment facility was good. The mean residual COD, BOD and TSS were 25, 8 and 21 mg l–1 and the corresponding percentage removal values were 90, 92 and 85%, respectively. The maximum percentage removal of oil and grease was 84% with a mean residual concentration of 24 mg l–1. The total viable count (22°C and 37°C), faecal coliform and aecal streptococci were reduced by 99.9% compared to only 99.5% for Salmonella. Bacteriological examination of the dried sludge indicated a reduction of nine logs of faecal coliform and faecal streptococci, as compared to thickened sludge. Analysis of the Ni, Cu, Pb and Cr in the dried sludge indicated that their concentrations are within the permissible limits. Zinc exceeded the consent standards by 50%. The results of the analyses of samples collected at the beginning of the irrigation canal indicated insignificant changes from the characteristics of the final effluent. Samples collected at a distance of 2km along the irrigation canal showed mean reductions in the COD and BOD of 28.6 and 47%, respectively, which could be attributed to sedimentation and/or a self-purification effect. An increase in the total nitrogen, total phosphorus and total viable count was also recorded, which could be due to seepage from the agricultural land. From the data available it is evident that the treated wastewater could be used for restricted irrigation. The design and implementation of a monitoring programme is recommended.     

USING WATER HYACINTH TO TREAT MUNICIPAL WASTEWATER IN THE DESERT SOUTHWEST1

ABSTRACT: Water hyacinth (Eichhornia crassipes L.) has shown to be effective in the treatment of municipal wastewater in a pilot study begun in January 1989 by the Pima County Wastewater Management Department and researchers associated with The University of Arizona's Office of Arid Lands Studies in the Sonoran Desert near Tucson. The influent pumped into the pilot facility's six raceways (ponds) typically has been treated secondary effluent diverted from a conventional treatment facility, although primary effluent from the same facility also has been treated. The Secondary Influent Treatment System has met the Arizona Department of Environmental Quality (ADEQ) tertiary standard for BOD₅ and TSS of 10 mg/l for every month of its operation since March 1990; the Primary Influent Treatment System met the ADEQ secondary standard for BOD₅ and TSS of 30 mg/1 for most of the 10 months it was in operation.     

The performance of constructed wetlands treating primary, secondary and dairy soiled water in Ireland (a review)

In Ireland, no database detailing the design, influent loading rates or performance of constructed wetlands (CWs) exists. On account of this, they are designed without any protocol based on empirical data. The aim of this paper was to provide the first published data on the performance of free-water surface flow (FWSF) CWs treating primary and secondary-treated municipal wastewater, and agricultural dairy soiled water (DSW) in Ireland. In total, the performance of thirty-four FWSF CWs, comprising fourteen CWs treating primary-treated municipal wastewater, thirteen CWs treating secondary-treated municipal wastewater, and seven CWs treating DSW, were examined. In most CWs, good organic, suspended solids (SS) and nutrient removal was measured. At an average organic loading rate (OLR) of 10 and 9 g biochemical oxygen demand (BOD) m(-2) d(-1), CWs treating primary and secondary wastewater removed 95 and 84% of influent BOD. Constructed wetlands treating DSW had an average BOD removal of 98%. At average SS loading rates of 6 and 14 g m(-2) d(-1), CWs treating primary and secondary wastewater had a 96 and an 82% reduction, and produced a final effluent with a concentration of 14 and 13 mg L(-1). Constructed wetlands treating DSW produced a final effluent of 34 mg L(-1) (94% reduction). Similar to other studies, all CWs examined had variable performance in ammonium-N (NH(4)(+)-N) removal, with average removals varying between 37% (for CWs treating secondary wastewater) and 88% (for CWs treating DSW). Variable ortho-phosphorus (PO(4)(3-)-P) removal was attributable to different durations of operation, media types and loading rates.     

新农村建设污水处理工程实例

山海关区新民居污水治理工程采用水解酸化+接触氧化+曝气生物滤池为主的工艺进行污水治理,实际运行结果表明:系统运行稳定,处理出水COD≤48 mg.L-1,BOD5≤9 mg.L-1,SS≤10 mg.L-1,NH3-N≤4.5 mg.L-1,TP≤0.47 mg.L-1,处理出水达到《城镇污水处理厂污染物排放标准》(GB 18918-2002)一级A标准,出水用于农村绿化和农灌,经济效益和环境效益明显。     

NITROGEN ACCUMULATION IN A CONSTRUCTED WETLAND FOR DAIRY WASTEWATER TREATMENT1

ABSTRACT: A free water surface (FWS) constructed wetland was installed at a dairy in Glendale, Arizona, to study the potential of such a wetland to remove nitrogen (N) from wastewater. The study objectives were: (1) to determine N removal from the wastewater, and (2) to evaluate N accumulation in soil and plant tissues. The system consisted of eight cells (70 × 9 × 1.5 m) planted with Typha domingensis, Scirpus validus, and Phragmites australis. The four cells in series were lined with plastic, and the four cells in a parallel series were lined with clay. Cells received approximately 180 m³/d of partially treated dairy effluent. Plant tissues and soil samples were collected above and below ground from 24 locations during one year. Total N removal from wastewater was about 17 percent. Clay‐lined cells accumulated more N in the soil and less N in plant biomass compared with plastic lined cells. Plant biomass accounted for approximately 60 percent of total N accumulated in cells with dense plant communities. Ninety percent of accumulated soil N was organic. Total N accumulated in soil reached a maximum (1,100 mg/kg) eight months after the introduction of wastewater.     

Performance of an overland flow system for advanced treatment of wastewater plant effluent

Overland flow (OF) systems were evaluated and compared for advanced treatment of municipal and industrial effluents, including nutrients and nondegradable chemical oxygen demand (COD) removal. Three pilot plants were constructed at the Shahin Shahr Wastewater Treatment Plant (WWTP), Isfahan, Iran. Each pilot was assigned a specific wastewater and all were simultaneously operated for 8 months. Treatment of primary effluent, activated sludge secondary effluent, and lagoon effluent of textile wastewater was investigated at application rates (ARs) of 0.15, 0.25, and 0.35m(3)m(-1)h(-1). During 5 months of stable operation after a 3-month acclimation period, mean removals of total 5-day biochemical oxygen demand (TBOD(5)), total COD (TCOD), total suspended solids (TSS), total nitrogen (TN), total phosphorus (TP) and turbidity were 74.5%, 54.8%, 66.2%, 39.4%, 35.8%, and 67.7% for primary effluent; 52.9%, 52.9%, 66.5%, 44.4%, 39.8%, and 50.1% for activated sludge effluent; 65.7%, 58.7%, 70.3%, 41.7%, 41.3%, and 54.9% for textile wastewater lagoon effluent, respectively. The model of Smith and Schroeder, 1985. Field studies of the overland flow process for the treatment of raw and primary treated municipal wastewater. Journal of Water Pollution Control Federation 57, 785-794] was satisfactory for TBOD(5). For all treatment parameters a standard first-order removal model was inadequate to represent the data but a modified first-order model provided a satisfactory fit to the data. Based on the results of this study, it can be concluded that an OF system as advanced treatment had the ability to meet effluent discharge permit limits and was an economical replacement for stabilization ponds and mechanical treatment options.     

QUALITY OF STORMWATER DRAINAGE FROM URBAN LAND1

ABSTRACT Urban storm water from a 1,067-acre drainage basin in Durham, N.C. was characterized to determine yield of pollutants. Population density averaged 9 persons per acre (ranging from <3 to 16). Annual BOD contribution attributable to surface wash during storms was determined to be approximately equal to contribution by its secondary wastewater treatment plant effluent. Total organic matter (COD) was estimated to exceed the amount in raw sanitary sewage from a residentially developed area of the same size. Mean basin yields (Ib/acre/day) were: BOD-0.23, COD-2.85, Total Solids-43.6, Volatile Total Solids-4.8, Total Phosphate-0.01 and Chloride-0.20 (as NaQ). The yield of lead presumed to originate from internal combustion engines operating on and near the basin was determined to be 0.006 Ib/acre/day. The concentration of total pesticides (Dieldrin; p,p'DDE; p,p-DDT; p,p'DDD and p,p'DDT) weighted for flow significance was estimated to be 1.2 parts per billion. The major long-term pollutional impact on a projected downstream reservoir was considered to be the fixed solids residue and long-term oxygen demand (COD). Intermittent release of other pollutants in slugs during runoff periods may be a significant factor in causing undesirable effects in streams draining urban areas.     

双滤料曝气生物滤池污水深度处理的研究

采用陶粒、沸石为滤料的曝气生物滤池对生物处理系统二级出水进行深度处理回用,研究了水力停留时间、气水体积比对污染物COD和NH3-N处理效果的影响。结果表明：水力停留时间为8 h,气水体积比为3∶1的工况下,处理效果较好。稳定运行后,出水COD、BOD5、SS、NH3-N、TP和色度平均值分别为15.6 mg/L、3.2 mg/L、8.5 mg/L、1.24 mg/L、0.40mg/L和8度,达到《城市污水再生利用—城市杂用水水质》（GB/T 18920-2002）标准,出水可用于道路清扫、绿化等。