Development and evaluation of RAMP I – a practitioner’s tool for screening of musculoskeletal disorder risk factors in manual handling

RAMP I is a screening tool developed to support practitioners in screening for work-related musculoskeletal disorder risk factors related to manual handling. RAMP I, which is part of the RAMP tool, is based on research-based studies combined with expert group judgments. More than 80 practitioners participated in the development of RAMP I. The tool consists of dichotomous assessment items grouped into seven categories. Acceptable reliability was found for a majority of the assessment items for 15 practitioners who were given 1?h of training. The usability evaluation points to RAMP I being usable for screening for musculoskeletal disorder risk factors, i.e., usable for assessing risks, being usable as a decision base, having clear results and that the time needed for an assessment is acceptable. It is concluded that RAMP I is a usable tool for practitioners.     

GA-g-PAMPS/AA/ST凝胶的制备及对亚甲基蓝吸附性能

采用微波辐射技术,通过接枝共聚反应制备了阿拉伯胶（GA）-g-2-丙烯酰胺-2-甲基丙磺酸（AMPS）/丙烯酸（AA）/海泡石黏土（ST）（GA-g-PAMPS/AA/ST）复合水凝胶,利用FTIR、XRD、SEM对复合水凝胶进行了表征,研究了水凝胶对水溶液中亚甲基蓝（MB）染料的吸附性能.结果显示：GA、ST和AA与AMPS发生了接枝共聚反应,形成具有均匀三维网络结构的复合水凝胶.0.025g水凝胶可以使体积为50mL、pH值为6.4、浓度为600mg/L的MB溶液的吸附量和吸附率分别达1146mg/g和95.5%,水凝胶具有较好的重复利用性能.Freundlich等温模型和准二级动力学模型能更好地描述吸附过程.热力学研究表明水凝胶对亚甲基蓝吸附是自发、吸热和不可逆的过程.该水凝胶可用作阳离子染料和阳离子型污染物的潜在候选生物质吸附剂.     

Ni2+对好氧颗粒污泥系统性能的影响

以城镇污水处理厂A²/O工艺的回流污泥作为接种污泥,在序批式反应器（SBR）中培养好氧颗粒污泥（AGS）,探究Ni²⁺对AGS系统的影响.结果表明：在25℃的条件下,50d左右培养出成熟的AGS,其形态多呈球状或椭球状,外表分布着少量丝状菌,颗粒污泥粒径主要在2~4mm,MLSS达6000mg/L,SVI维持在40~50mL/g.将Ni²⁺作用于培养出的成熟AGS,Ni²⁺在0~2mg/L的浓度范围内会提高AGS的稳定性,使MLSS上升,SVI降低;同时会促进AGS分泌胞外多聚物（EPS）,EPS组成成分中的蛋白质（PN）明显多于多糖（PS）;Ni²⁺对好氧颗粒污泥去除总氮（TN）的抑制程度要大于COD,最终COD去除率可维持在95%以上,TN去除率可维持在70%以上.     

矿物材料吸附去除污水中磷的试验研究

采用粉煤灰、高岭土、泥渣(取电厂澄清池排泥作脱水干燥处理)作为吸附剂深度处理污水中的磷,对比分析了3种吸附剂的吸附速度、吸附性能及除磷效果。结果表明:粉煤灰和高岭土用时20 min完成对磷的有效吸附,沉降泥渣用时5 min即可实现同等吸附效果;沉降泥渣对污水中磷的吸附能力较好,投加量为0.2 g/L的泥渣对磷的去除率可达98.1%,而投加量为0.2 g/L粉煤灰或高岭土对磷的去除率仅达到77.2%。     

提升汇流环湿热环境适应性方法研究

目的提高汇流环在湿热环境下的适应能力。方法实物解剖,观察汇流环绝缘材料损坏情况、碳粉堆积情况,在不同温度、湿度下测试绝缘材料绝缘度、抗电强度,碳粉堆积和导电情况,比对不同绝缘材料性能,并找出最适合的绝缘材料,比对滚动汇流环、碳刷组件、刷丝组件,找到解决碳粉堆积的方法。结果汇流环受湿热影响会从接缝处和电缆连接处进入湿气,温度、湿度的上升会使得原绝缘材料性能下降,长时间使用汇流环,碳粉会在汇流环内堆积并受到湿热的影响而导电,局部密封汇流环可以减少湿气进入。PPO材料性能优异,可以替换原绝缘材料从而减少湿热的影响,使用刷丝组件替代碳刷可以避免碳粉的产生。结论综合运用局部密封、绝缘材料改进、碳刷组件改进三种措施,可以有效提高汇流环在湿热环境下的适应能力。     

聚合物材料在快速原型制造技术中的应用

介绍聚合物材料作为成形原料在主要的快速原型制造(RPM)工艺中的应用情况。具体按照立体印刷成形(SLA)、层合实体制造(LOM)、选域激光烧结(SLS)及熔融沉积造型(FDM)这4种工艺的不同,阐述与各工艺对应的聚合物材料的种类、聚合物材料成形过程中可能出现的问题及解决方案。总结了聚合物材料原型的应用情况和聚合物材料在RPM技术应用中存在的问题。     

Carbon Dioxide Balance of Wood Substitution: Comparing Concrete- and Wood-Framed Buildings

In this study a method is suggested to compare the net carbon dioxide (CO₂) emission from the construction of concrete- and wood-framed buildings. The method is then applied to two buildings in Sweden and Finland constructed with wood frames, compared with functionally equivalent buildings constructed with concrete frames. Carbon accounting includes: emissions due to fossil fuel use in the production of building materials; the replacement of fossil fuels by biomass residues from logging, wood processing, construction and demolition; carbon stock changes in forests and buildings; and cement process reactions. The results show that wood-framed construction requires less energy, and emits less CO₂ to the atmosphere, than concrete-framed construction. The lifecycle emission difference between the wood- and concrete-framed buildings ranges from 30 to 130 kg C per m² of floor area. Hence, a net reduction of CO₂ emission can be obtained by increasing the proportion of wood-based building materials, relative to concrete materials. The benefits would be greatest if the biomass residues resulting from the production of the wood building materials were fully used in energy supply systems. The carbon mitigation efficiency, expressed in terms of biomass used per unit of reduced carbon emission, is considerably better if the wood is used to replace concrete building material than if the wood is used directly as biofuel.     

电解制备聚合铝过程中Alb形态生成条件研究

考察了电解法制备聚合铝过程中AIb的最佳形成条件。AIb的形成与电流密度、极板间距、电解液的温度、铝的浓度以及电解时间等因素有关。在制备AI浓度为2．0mol/L的聚合氯化铝时，最佳的电流密度和极板间距分别为1．1A／dm^2和10mm。由于电化学过程中产生的不均匀的界面pH差值较大而生成较多的AI（OH）4^-作为AIb结构的结晶核心，因此能形成更多的AIb聚合形态。     

混凝研究中的界面过程化学:IPF-颗粒物-水溶液的相互作用

仅以IPF 颗粒物 水溶液的相互作用为例 ,对混凝研究中二界面过程化学领域的进展加以介绍 .研究结果表明 ,经过预制的聚合铝在混凝过程中表现出较好的形态稳定性 ,而传统混凝剂则强烈地受溶液化学过程 ,尤其是溶液pH值的影响 .混凝剂水解聚合形态倾向于在颗粒物表面吸附沉积 ,而直接引发混凝作用 .单体形态则通过转化为聚合、沉淀形态起混凝作用     

国内外军工材料环境试验现状及发展趋势

介绍军工材料环境试验对提高装备环境适应性的重要作用。从不同的技术方面,分析了国内外军工材料环境试验的现状、发展趋势以及主要差距。从规划的制定、新技术新方法的研发以及信息共享方面,提出设想。提出了目前需要研发新的环境试验、评价、管理方法和需要突破的关键技术。