Combustion and inorganic bromine emission of waste printed circuit boards in a high temperature furnace

High temperature combustion experiments of waste printed circuit boards (PCBs) were conducted using a lab-scale system featuring a continuously-fed drop tube furnace. Combustion efficiency and the occurrence of inorganic bromine (HBr and Br₂) were systematically studied by monitoring the main combustion products continuously. The influence of furnace temperature (T) was studied from 800 to 1400 °C, the excess air factor (EAF) was varied from 1.2 to 1.9 and the residence time in the high temperature zone (RT_HT) was set at 0.25, 0.5, or 0.75 s.Combustion efficiency depends on temperature, EAF and RT_HT; temperature has the most significant effect. Conversion of organic bromine from flame retardants into HBr and Br₂ depends on temperature and EAF. Temperature has crucial influence over the ratio of HBr to Br₂, whereas oxygen partial pressure plays a minor role. The two forms of inorganic bromine seem substantially to reach thermodynamic equilibrium within 0.25 s. High temperature is required to improve the combustion performance: at 1200 °C or higher, an EAF of 1.3 or more, and a RT_HT exceeding 0.75 s, combustion is quite complete, the CO concentration in flue gas and remained carbon in ash are sufficiently low, and organobrominated compounds are successfully decomposed (more than 99.9%).According to these results, incineration of waste PCBs without preliminary separation and without additives would perform very well under certain conditions; the potential precursors for brominated dioxins formation could be destroyed efficiently. Increasing temperature could decrease the volume percentage ratio of Br₂/HBr in flue gas greatly.     

Biomonitoring perfluorinated compounds in Catalonia,Spain: concentrations and trends in human liver and milk samples

Background, aim and scope  

Perfluorinated compounds (PFCs) are global environmental pollutants that bioaccumulate in wildlife and humans. Laboratory experiments have revealed toxic effects such as delayed development, humoral suppression, and hepatotoxicity. Although numerous human blood levels have been reported, little is known about distribution in the human body. Knowledge about PFC distribution and accumulation in the human body is crucial to understanding uptake and subsequent effects as well as to conduct risk assessments. The present study reports PFC levels in human liver and breast milk from a general population living in Catalonia, Spain. Liver and milk levels are compared to previously reported levels in blood from the same geographic area as well as to other existing reports on human liver and milk levels in other countries.     

Vinyl 2010 — nearing the target date

For almost 10 years, Vinyl 2010 has provided original approaches to technical, environmental, and political problems relating to poly(vinyl chloride) (PVC) material cycles and waste management. On the one hand, PVC has outstanding qualities in a wide range of applications; on the other hand, concerns about potential impacts attributed to production, additives, and waste management led to calls for PVC-specific regulations and mandatory substitution in certain applications. Considering the entire life cycle of PVC products, the industry proposed a comprehensive set of measures rendering production cleaner, eliminating controversial additives, and promoting responsible management of waste, favoring recycling. Vinyl 2010 can now be regarded as a highly successful example of applying voluntary commitments instead of the more usual command and control approach from regulatory authorities.     

A Generic Bio-Economic Farm Model for Environmental and Economic Assessment of Agricultural Systems

Bio-economic farm models are tools to evaluate ex-post or to assess ex-ante the impact of policy and technology change on agriculture, economics and environment. Recently, various BEFMs have been developed, often for one purpose or location, but hardly any of these models are re-used later for other purposes or locations. The Farm System Simulator (FSSIM) provides a generic framework enabling the application of BEFMs under various situations and for different purposes (generating supply response functions and detailed regional or farm type assessments). FSSIM is set up as a component-based framework with components representing farmer objectives, risk, calibration, policies, current activities, alternative activities and different types of activities (e.g., annual and perennial cropping and livestock). The generic nature of FSSIM is evaluated using five criteria by examining its applications. FSSIM has been applied for different climate zones and soil types (criterion 1) and to a range of different farm types (criterion 2) with different specializations, intensities and sizes. In most applications FSSIM has been used to assess the effects of policy changes and in two applications to assess the impact of technological innovations (criterion 3). In the various applications, different data sources, level of detail (e.g., criterion 4) and model configurations have been used. FSSIM has been linked to an economic and several biophysical models (criterion 5). The model is available for applications to other conditions and research issues, and it is open to be further tested and to be extended with new components, indicators or linkages to other models.     

Effect of temperature and particle size on the thermal desorption of PCBs from contaminated soil

Thermal desorption is widely used for remediation of soil contaminated with volatiles, such as solvents and distillates. In this study, a soil contaminated with semivolatile polychlorinated biphenyls (PCBs) was sampled at an interim storage point for waste PCB transformers and heated to temperatures from 300 to 600 °C in a flow of nitrogen to investigate the effect of temperature and particle size on thermal desorption. Two size fractions were tested: coarse soil of 420–841 μm and fine soil with particles <250 μm. A PCB removal efficiency of 98.0 % was attained after 1 h of thermal treatment at 600 °C. The residual amount of PCBs in this soil decreased with rising thermal treatment temperature while the amount transferred to the gas phase increased up to 550 °C; at 600 °C, destruction of PCBs became more obvious. At low temperature, the thermally treated soil still had a similar PCB homologue distribution as raw soil, indicating thermal desorption as a main mechanism in removal. Dechlorination and decomposition increasingly occurred at high temperature, since shifts in average chlorination level were observed, from 3.34 in the raw soil to 2.75 in soil treated at 600 °C. Fine soil particles showed higher removal efficiency and destruction efficiency than coarse particles, suggesting that desorption from coarse particles is influenced by mass transfer.     

Some technical issues in managing PCBs

Polychlorinated biphenyls (PCBs) were important industrial chemicals featuring high thermal and chemical stability and low flammability. They were widely used as dielectric and thermal fluid in closed electro-technical applications (transformers, capacitors…) and also in numerous dispersive uses, ranking from auto-copying paper to sealant or coatings. During the 1960s, severe environmental consequences started becoming apparent. The stability of PCBs contributed to their persistence in the environment, their lipophilic character to bio-magnification. Fish-eating species seemed threatened in their existence. In Japan and in Taiwan, thousands of people consumed PCB-contaminated oil. The production of PCBs stopped completely during the 1980s. Usage could continue in closed applications only. In this paper, particular attention is given to two issues: the cleaning of PCB electric transformers and the potential impact of PCB-containing building materials. Other contributions will cover the management and treatment of PCB-contaminated soil, sludge or fly ash. The complete survey is being prepared by request of the Knowledge Center for Engineers and Professionals.     

Waste incineration,PVC, and dioxins

Waste incineration is becoming increasingly necessary to tackle the rapidly rising amounts of municipal solid waste (MSW); in China many large cities are already surrounded by a girdle of landfills. Still, the not-in-my-backyard (nimby) syndrome holds strong. This attitude stems from fear of dioxins. These have been associated with incineration (‘dioxin factories’) and at times also with polyvinylchloride. In this paper this issue is analysed. China should build additional trust in MSW incineration, following promulgation of stricter emission standards, enforced by stringent controls.     

Levels of PCDD/F in adipose tissue on non-occupationally exposed subjects living near a hazardous waste incinerator in Catalonia, Spain

The potential adverse effects on human health of hazardous waste incinerators (HWIs) are a subject of concern. The construction of the first and till now only HWI in Spain finished in 1999. In 2007, after approximately 9 years of regular operations in the facility, the concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) were determined by HRGC/HRMS in samples of adipose tissue of 15 autopsied subjects living in the area under potential impact of the HWI (Constantí, Tarragona County, Catalonia). These data were compared with the levels found in two previous surveys performed in 1998 (baseline) and 2002. The current mean PCDD/F concentration in adipose tissue was 14.6 pg WHO-TEQ/g of fat (range: 3.3–55.4 pg WHO-TEQ/g of fat). It means significant changes (a reduction of 64% and an increase of 47%) in the mean PCDD/F levels in comparison to those found in 1998 and 2002: 40.1 and 9.9 pg WHO-TEQ/g of fat, respectively. Women showed higher levels of PCDD/F than men (23.8 vs 11.2 pg WHO-TEQ/g of fat). The increase in the last 5 years would not be directly attributable to exposure to PCDD/F emitted by the HWI, as other biological monitors such as human plasma and milk decreased during the same period.     

De novo formation of dioxins from milled model fly ash

Environmental Science and Pollution Research - Municipal solid waste incineration (MSWI) fly ash has been classified as hazardous waste and needs treatment in an environmentally safe manner....     

Baseline soil levels of PCDD/Fs established prior to the construction of municipal solid waste incinerators in China

In order to determine the baseline contamination by polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in different areas in China, prior to the construction of municipal solid waste incinerators (MSWIs), a total of 32 representative soil samples was collected near 16 incinerators and analyzed for their PCDD/F concentrations. The PCDD/F baseline concentrations in the soil samples ranged from 0.32 to 11.4 ng I-TEQ kg⁻¹ (dry matter), with average and median value of 2.73 and 2.24 ng I-TEQ kg⁻¹ (dry matter), respectively, and a span between maximum and minimum recorded value of 36. The PCDD homologues predominated in 26 out of 32 soil samples, with the ratio (PCDDs)/(PCDFs) ranging from 1.1 to 164; however in the other 6 samples, PCDF homologues were larger, with the same ratio varying from 0.04 to 0.8. Principal component analysis (PCA) and hierarchical cluster analysis (HCA) were used to examine PCDD/F amount and profile in these soil samples, and their possible associations with known emission sources: in this process 6 really distinct isomer fingerprints were identified. Background PCDD/F levels and profiles were comparable to those found in soils from China and other countries and indicate a rather low baseline PCDD/F contamination of soils. The present data provide the tools for future assessment of a possible impact of these MSWIs.