亚热带稻田土壤碳氮磷生态化学计量学特征

为了解稻田土壤中是否存在稳定的土壤有机碳(C)、氮(N)和磷(P)比值,基于亚热带区110个水稻土剖面和587个发生层的土壤调查数据库,在区域尺度上分析了典型水稻土C∶N∶P比值的生态化学计量学特征,并应用相关分析和冗余分析,研究水稻土C∶N∶P比值与土壤-环境因子(地形和母质、土壤发生层、土壤类型和土壤理化性质)的关系.结果显示,亚热带区稻田土壤C∶N、C∶P和N∶P的剖面加权平均值分别为12. 6、49和3. 9,C∶N∶P为38∶3. 2∶1.不同母质起源、不同土壤亚类和不同发生层的水稻土C∶N变异相对较小;但C∶P和N∶P的变异很大,两者均值也远低于全球(186和13. 1)和中国土壤(136和9. 3)的C∶P和N∶P的平均水平.尽管稻田土壤剖面的C∶N∶P相对不稳定,但由于稻田表土生物与环境相互作用强烈,表土C∶N相对稳定(14. 2).这反映长期水耕熟化作用下,稻田表土中C和N仍存在紧密的耦合作用.然而,在稻田土壤剖面上,C∶P和N∶P并不稳定,SOC与全P含量、全N与全P含量也无显著相关性,表明环境变化可能导致土壤C∶N∶P解耦.地形、土壤质地、氧化铁和容重是调控稻田土壤剖面C∶N∶P的关键土壤环境因子.     

哈长城市群县域碳排放空间溢出效应及影响因素研究——基于NPP-VIIRS夜间灯光数据的实证

基于2012-2016年NPP-VIIRS夜间灯光数据测算哈长城市群共计68个县级单元碳排放数据,采用空间自相关、位序规模法则、空间计量模型以及空间马尔科夫链模型,对县级尺度城市碳排放空间特征、影响因素和动态空间溢出作用进行分析.结果表明：①城市碳排放呈现逐年下降的趋势,空间Moran''s I指数表明研究区城市碳排放存在高度的空间自相关,碳排放的高值集聚性呈降低的趋势.②位序规模法则表明,研究区全部城市的碳排放属于次位型分布,高位次城市的碳排放表现突出;在前十位城市的碳排放规模先减少再增加,由分散向集中演变.③多种空间面板模型对比分析表明,城市经济水平和人口密度因素呈现显著的正相关关系;固定投资和外商投资因素仅在时间固定模型中起到正向影响作用;技术进步以及路网密度因素则起到显著的抑制作用.④空间马尔科夫链分析结果表明,城市碳排放空间溢出效应明显,位于低水平区域与高水平区域的城市在转移过程中保持稳定;位于中低水平区域的城市与高碳排放的城市相邻会降低转移概率,反之则会提升转移概率.     

基于LOADEST和数字滤波的水源地基流氮素输出定量方法应用实例

地表直接径流和基流均是流域非点源氮/磷养分输出的重要水文途径.科学认识和定量模拟基流氮/磷养分输出对于准确解析水源地水体非点源污染来源至关重要.基于Load Estimator模型和数字滤波算法,建立了定量水源地基流氮素输出的方法体系.以浙江省珊溪水源地的玉泉溪流域为例,利用玉泉溪2010-01—2013-12期间逐月总氮(TN)水质监测数据和逐日流量数据,展示了该方法的计算过程.结果表明,本文建立的水源地基流氮素输出定量方法结果合理,模拟精度高,决定系数和纳什系数分别为0.83和0.80;玉泉溪流域2010—2013年TN负荷量为141.21～274.68 t·a~(-1),平均208.63 t·a~(-1),年基流TN负荷量为84.39～168.68 t·a~(-1),平均127.69 t·a~(-1);基流对玉泉溪年均TN负荷量贡献率高达60%以上,流域基流养分输出对地表水体的污染应引起足够重视.     

沱江沉积物中有机氯农药分布特征及其与藻类有机质的关系和生态风险评估

使用气相色谱-质谱联用仪分析了长江支流沱江流域48个表层沉积物中有机氯农药（organochlorine pesticides,OCPs）的残留水平,探讨了其分布和组成特征及其与总有机碳（total organic carbon,TOC）、藻类有机质之间的关系,以及评估其生态风险.结果表明沱江流域表层沉积物中OCPs的总含量为3.17~127 ng·g^-1,其中六六六（hexachlorocyclohexane,HCHs）类农药的含量为2.83~86.0 ng·g^-1,滴滴涕（dichlorodiphenyltrichloroethane,DDTs）类农药的含量为0.340~40.9 ng·g^-1.OCPs空间分布特点为：上游 < 中游 < 下游 < 支流.HCHs和DDTs的组成成分分析表明,沱江流域存在林丹输入的现象,主要来自于历史残留,这与绝大多数流域的DDTs的输入状况相似.OCPs含量与TOC、藻类有机质含量之间存在着极显著的正相关性关系,表明藻类有机质在TOC对沉积物中的OCPs分配中起更为重要的作用.生态风险评估表明,沱江流域表层沉积物的有机氯农药存在较大的生态风险,可能对河流的底栖生物及生态环境造成明显的影响.     

深圳湾流域面源与截排溢流污染特征及其对水环境的影响

随着点源污染逐步得到有效控制,面源与截排溢流污染对水环境的胁迫日益突出。基于土地遥感数据、城市排水管网等资料,构建流域—海湾一体化水环境模型,探讨深圳湾流域面源与截排溢流污染特征及其对水环境的影响,研究表明：（1）雨季COD、NH₃-N和TP单位面积面源与截排溢流污染负荷分别为17.21 t/km²与10.21 t/km²、0.17 t/km²与0.69 t/km²、0.04 t/km²与0.07 t/km²;（2）面源与截排溢流污染时间上主要集中于大雨及以上等级降水较多的5月和8月,空间上主要分布在截排工程集中、下垫面面积较大且坡度较陡的深圳河、大沙河和新洲河流域;（3）面源与截排溢流水体COD、NH₃-N和TP浓度可达地表水V类标准的3.7倍、18.2倍和8.5倍;（4）雨季COD、NH₃-N和TP浓度高于旱季的区域分别超过深圳湾总面积的40%、60%和65%。     

科技创新投入对环境全要素生产率的影响机制

使用2004~2015年的中国280个地级市的面板数据,对科技创新投入与环境全要素生产率间的非线性关系、内部影响机理和空间异质性进行分析,结果显示：科技创新投入与环境全要素生产率之间呈现倒N型关系,两个拐点的位置分别为7.722（2257.47万元）和9.610（14913.17万元）;在外部资本进入、污染治理、市场规模效应3种影响路径中,科技创新投入影响下的外部资本进入对环境全要素生产率依然存在污染避难所的负向效应,科技创新投入与外部资本间效应为0.1363,外部资本与环境全要素生产率间效应为-0.0065;科技创新投入能够增强企业的污染治理技术并提高环境全要素生产率,三者间前后效应分别为-0.0277和-0.0311;科技创新的投入与高效益增强了市场规模效应,有效促进生产结构的转型进而提高环境全要素生产率,三者间前后效应为0.0186和0.4346.空间异质性中,外部资本进入与溢出效应带来的污染避难所负效应在中部地区显著,在西部和东北部地区不显著,而污染天堂正效应在东部地区存在但不显著;污染创新治理投入的技术正溢出效应在东部和西部地区效应显著,在中部和东北部不显著;科技创新投入与市场需求规模效应在空间区域无差异且显著为正.建议依据科技创新投入的不同影响路径来实施空间差异化策略.     

黄海麻坑群沉积物磷的保存与转化及环境效应

基于对北黄海典型麻坑群海域某单位麻坑内部和外缘沉积物中不同赋存形态的磷、甲烷（CH₄）和硫化物等参数的分析,探讨了麻坑独特的环境中磷的转化与埋藏机制、沉积物-水体系磷的释放及对区域磷循环的影响.研究表明,沉积物中碎屑态磷（Det-P）是磷主要的赋存形态（>50%）,其次是有机磷（Org-P）、铁结合态磷（Fe-P）和自生态磷（Auth-P）,交换态磷（Exch-P）对总磷的贡献较小;麻坑内部与麻坑外缘处沉积物中溶解态活性磷（DRP）向水体的释放通量分别为2.84μmol/（cm²·a）和1.03μmol/（cm²·a）,对上层水体的贡献依次为19.6%和3.03%,是上层水体磷的重要来源.麻坑内外磷的埋藏速率与转化过程存在不同;研究区地下水的渗漏是磷的沉积速率和释放通量都普遍高的原因.北黄海麻坑区沉积物中磷的保存与转化还与浅层CH₄的逸出相关,潜在提高黄铁矿的生成速率.较高的沉积物-水界面磷通量必然对区域富营养化等生态环境问题产生深远影响,值得关注.     

新型厌氧多级喷动床及其厌氧氨氧化脱氮性能分析

为改善厌氧反应器内的流态,加快污泥的颗粒化和形成具有生态梯度的微生物生态系统,设计并制作了新型厌氧多级喷动床,实验测试了反应器的水力喷动、气体喷涌和污泥分层分级现象。在常温下,利用新型厌氧多级喷动床接种混合污泥,经过42 d的培养,成功启动厌氧氨氧化反应器,稳定运行18 d后,NH₄+-N、NO₂--N去除率均达到90%以上。启动60 d后,反应器底部出现大量粒径2 mm左右的颗粒污泥,且污泥具有良好的稳定性和沉降性能,沉降速度达到70 m/h。结果表明:厌氧多级喷动床因其特殊的水力结构,可有效加快污泥的颗粒化。     

Regulated emission characteristics of in-use LNG and diesel semi-trailer towing vehicles under real driving conditions using PEMS

On-road driving emissions of six liquefied natural gas(LNG) and diesel semi-trailer towing vehicles(STTVs) which met China Emission Standard IV and V were tested using Portable Emission Measurement System(PEMS) in northern China.Emission characteristics of these vehicles under real driving conditions were analyzed and proved that on-road emissions of heavy-duty vehicles(HDVs) were underestimated in the past.There were large differences among LNG and diesel vehicles, which also existed between China V vehicles and China IV vehicles.Emission factors showed the highest level under real driving conditions, which probably be caused by frequent acceleration, deceleration, and start-stop.NOx emission factors ranged from 2.855 to 20.939 g/km based on distance-traveled and 6.719–90.557 g/kg based on fuel consumption during whole tests, which were much higher than previous researches on chassis dynamometer.It was inferred from tests that the fuel consumption rate of the test vehicles had a strong correlation with NOx emission, and the exhaust temperature also affected the efficiency of Selected Catalytic Reduction(SCR) aftertreatment system, thus changing the NOx emission greatly.THC emission factors of LNG vehicles were 2.012–10.636 g/km, which were much higher than that of diesel vehicles(0.029–0.185 g/km).Unburned CH_4 may be an important reason for this phenomenon.Further on-road emission tests, especially CH_4 emission test should be carried out in subsequent research.In addition, the Particulate Number(PN) emission factors of diesel vehicles were at a very high level during whole tests, and Diesel Particulate Filter(DPF)should be installed to reduce PN emission.     

Bioassay: A useful tool for evaluating reclaimed water safety

Wastewater reclamation and reuse has been proved to be an effective way to relieve the fresh water crisis. However, toxic contaminants remaining in reclaimed water could lead to potential risk for reuse, and the conventional water quality standards have difficulty guaranteeing the safety of reclaimed water. Bioassays can vividly reflect the integrated biological effects of multiple toxic substances in water as a whole, and could be a powerful tool for evaluating the safety of reclaimed water. Therefore, in this study, the advantages and disadvantages of using bioassays for evaluating the safety of reclaimed water were compared with those of conventional water quality standards. Although bioassays have been widely used to describe the toxic effects of reclaimed water and treatment efficiency of reclamation techniques, a single bioassay cannot reflect the complex toxicity of reclaimed water, and a battery of bioassays involving multiple biological effects or in vitro tests with specific toxicity mechanisms would be recommended. Furthermore, in order to evaluate the safety of reclaimed water based on bioassay results, various methods including potential toxicology, the toxicity unit classification system, and a potential eco-toxic effects probe are summarized as well. Especially, some integrated ranking methods based on a bioassay battery involving multiple toxicity effects are recommended as useful tools for evaluating the safety of reclaimed water, which will benefit the promotion and guarantee the rapid development of the reclamation and reuse of wastewater.