海啸破坏特点与工程防御方法初探

印度洋海啸现场调查表明,海啸灾害不同于地震和洪水灾害.海啸通过高水位淹没和浪涌冲击对海边地势低平地区的房屋、道路、桥梁、机场以及给排水、供电、通讯等设施与车辆、船只造成严重破坏.海啸上岸后,由于巨大的冲力,将夹带一些破损建筑物产生的固体漂浮物一同前进,因此破坏力更强.由于淹没、浪涌、冲毁建筑物压埋以及漂浮物冲击等综合作用,造成人员死亡率极高,所过之处,财物殆尽.抗御海啸灾害的工程措施主要在于合理规划(避让、削弱、分流、阻挡)和科学设计(潜在海啸灾害等级划分、结构性态决策、海啸荷载确定、抗海啸分析、构造设计).     

电站煤粉锅炉垂直和水平浓淡燃烧方式对NOx排放量和锅炉效率的影响

将420t／h锅炉一次风口的水平浓淡燃烧器改造为垂直浓淡燃烧器。通过对改造前后分别进行的NOx排放特性试验，比较分析了一次风喷口采用水平和垂直浓淡燃烧器对锅炉效率和NOx排放特性的影响。     

西昌高原鳅人工繁殖技术研究

对西昌高原鳅(Triplophysa xichangensis)人工繁殖中的催产药物及其剂量、受精方式、孵化方法和仔鱼水花培育方法等一系列关键技术进行了详细研究。结果表明,对性腺发育至Ⅳ+~Ⅳ++期的雌鱼分二次注射LRH-A2 0.1μg/g(鱼体重)和HCG 20 IU/g(鱼体重),雄鱼剂量减半,注射量0.1 mL,能很好地促进雌雄鱼发情并产卵排精,在水温19±0.5℃时的效应时间为30.5~31 h;在一个特制的塑料盆中完成了亲鱼培育、打针催产、发情、自然产卵受精、孵化以及仔鱼培育等全部人工繁殖过程,受精率、孵化率和仔鱼水花培育20 d的成活率平均分别为97.2%、85%和85%。本研究成果可应用于西昌高原鳅规模化繁育,对长江上游鱼类生物多样性保护有着积极意义。     

Research and application of method of oxygen isotope of inorganic phosphate in Beijing agricultural soils

Phosphorus (P) in agricultural ecosystems is an essential and limited element for plants and microorganisms. However, environmental problems caused by P accumulation as well as by P loss have become more and more serious. Oxygen isotopes of phosphate can trace the sources, migration, and transformation of P in agricultural soils. In order to use the isotopes of phosphate oxygen, appropriate extraction and purification methods for inorganic phosphate from soils are necessary. Here, we combined two different methods to analyze the oxygen isotopic composition of inorganic phosphate (δ¹⁸O_P) from chemical fertilizers and different fractions (Milli-Q water, 0.5 mol L^?1 NaHCO₃ (pH = 8.5), 0.1 mol L^?1 NaOH and 1 mol L^?1 HCl) of agricultural soils from the Beijing area. The δ¹⁸O_P results of the water extracts and NaHCO₃ extracts in most samples were close to the calculated equilibrium value. These phenomena can be explained by rapid P cycling in soils and the influence of chemical fertilizers. The δ¹⁸O_P value of the water extracts and NaHCO₃ extracts in some soil samples below the equilibrium value may be caused by the hydrolysis of organic P fractions mediated by extracellular enzymes. The δ¹⁸O_P values of the NaOH extracts were above the calculated equilibrium value reflecting the balance state between microbial uptake of phosphate and the release of intracellular phosphate back to the soil. The HCl extracts with the lowest δ¹⁸O_P values and highest phosphate concentrations indicated that the HCl fraction was affected by microbial activity. Hence, these δ¹⁸O_p values likely reflected the oxygen isotopic values of the parent materials. The results suggested that phosphate oxygen isotope analyses could be an effective tool in order to trace phosphate sources, transformation processes, and its utilization by microorganisms in agricultural soils.     

棉花耐涝相关种质资源遗传多样性分析

为了解棉花耐涝相关种质资源的遗传多样性，选用均匀分布于棉花全基因组的145对引物，从中筛选出44对SSR引物对48份涝相关种质资源进行遗传多样性分析。结果表明，44对SSR引物在48份材料中共检测出170个等位基因变异,平均每个位点有386个。其中耐涝材料的位点多态信息含量(PIC)、每个位点的有效等位基因数(Ne)、基因型多样性(H′)分别为0632、1710 4和0393 7,涝敏感材料的PIC、Ne、H′分别为0628、1721 6和0399 4。耐涝材料和涝敏感材料的Jaccard相似性系数分别在0462~0925和0398~0845之间,遗传相似性系数总体平均值接近,但耐涝材料的变化幅度更大。用类平均法(UPGMA)聚类将48份材料分成2个类群。其中，第Ⅰ类包含39个品种，第Ⅱ类包含9个品种。大多数材料之间的遗传相似性系数较高,表明陆地棉耐涝相关种质资源遗传基础狭窄。本结果可为棉花耐涝育种亲本选配和相关机理研究提供基础资料     

运动消耗对草鱼幼鱼游泳能力的影响

以草鱼幼鱼（体长80~97 cm，体重96~134 g）为研究对象，采用实验室专利装置研究了不同运动消耗状态下的草鱼幼鱼游泳能力。结果表明：在正常状态下草鱼幼鱼的临界游泳速度[WTBX]（Ucrit）为711±060 BL/s，耗氧率（MO2）与流速（U）方程拟合为MO2=4705+419U123，耗氧率随着流速的增大而增大，且草鱼的有氧运动效率较高。在4种运动消耗状态（06Ucrit、08Ucrit、10Ucrit、12Ucrit）流速下运动1 h草鱼的消耗后临界游泳速度（Upcrit）分别为：725±135、633±06、626±08、560±04 BL/s，临界游泳速度随着前期消耗流速的增大而减小，相应的耗氧率方程拟合为：MO2=38269+465U144，MO2=44526+4223U146，MO2=46611+4790U149，MO2=60034+3883U151。运动消耗会导致草鱼的有氧运动效率降低，同时随着运动消耗速度的增加有氧运动效率随之降低。研究结果认为在设计以草鱼为主要过鱼对象的过鱼设施时，鱼道内的流速不应大于08Ucrit，以使鱼类顺利通过。针对不同过鱼对象游泳特性进行设计的鱼道能够提高鱼类通过鱼道的效率     

Individual and combined inhibition of phenol and thiocyanate on microbial activity of partial nitritation

This study evaluated the individual and interactive effect of phenol and thiocyanate (SCN⁻) on partial nitritation (PN) activity using batch test and response surface methodology. The IC₅₀ of phenol and SCN⁻ on PN sludge were 5.6 and 351 mg L⁻¹, respectively. The PN sludge was insensitive to phenol and SCN⁻ at levels lower than 1.77 and 43.3 mg L⁻¹, respectively. A regression model equation was developed and validated to predict the relative specific respiration rate (RSRR) of PN sludge exposed to different phenol and SCN⁻ concentrations. In the range of independent variables, the most severe inhibition was observed with a valley value (17%) for RSRR, when the phenol and SCN⁻ concentrations were 4.08 and 198 mg L⁻¹, respectively. An isobole plot was used to judge the combined toxicity of phenol and SCN⁻, and the joint inhibitory effect was variable depending on the composition and concentration of the toxic components. Furthermore, the toxic compounds showed independent effects, which is the most common type of combined toxicity.

     

Hazardous substances in indoor dust emitted from waste TV recycling facility

Various hazardous substances contained in waste TV sets might be released into environment via dust during recycling activities. Two brominated flame retardants (BFRs), polybrominated diphenyl ethers (PBDEs), and tetrabromobisphenol A (TBBPA), and five kinds of heavy metals (Cu, Pb, Cd, Cr, and Ni) were detected in indoor dust collected from two workshops (TV dismantling workshop and subsequent recycling workshop). PBDEs concentrations in dust from waste wires recycling line (722,000 ng/g) were the highest among the studied sites, followed by those in manual dismantling–sorting line (117,000 ng/g), whereas TBBPA concentrations were the highest in manual dismantling–sorting line (557 ng/g) and printed circuit board (PCB) recycling line (428 ng/g). For heavy metals, Cu and Pb were the most enriched metals in all dust samples. The highest concentration of Pb (22,900 mg/kg) was found in TV dismantling workshop-floor dust. Meanwhile, Cu was the predominant metal in dust from the PCB recycling line, especially in dust collected from electrostatic separation area (42,700 mg/kg). Occupational exposure assessment results showed that workers were the most exposed to BDE-209 among the four PBDE congeners (BDE-47, BDE-99, BDE-153, and BDE-209) in both workshops. The hazard quotient (HQ) indicated that noncancerous effects were unlikely for both BFRs and heavy metals (HQ?<?1), and carcinogenic risks for Cd, Cr, and Ni (risk?<?10^?6) on workers in two workshops were relatively low.     

竹制填料生物接触氧化工艺处理污染河水简

针对受污染的湖溪河水质特征，以传统弹性塑料填料做对比，研究以竹球和竹丝为填料的生物接触氧化工艺，考察填料的挂膜时间、生物量和污水处理效果；确定连续曝气和间歇曝气时反应器的最优运行工况：连续曝气时为HRT=7.5 h，DO=3 mg/L；间歇曝气时为厌氧1.2 h、好氧6.3 h交替运行。实验结果表明，与弹性塑料填料相比，竹制填料挂膜速度快，竹球填料的水处理效果最好；连续曝气最优工况下竹球填料反应器中COD、TN、NH₃-N和TP的平均去除率分别为66.7%、47.9%、57.1%和30.6%；间歇曝气最优工况下竹球填料反应器中COD、TN、NH₃-N和TP的平均去除率分别64.08%、39.95%、60.7%和54.68%；竹制填料可替代传统的塑料填料作为生物接触氧化工艺的载体填料。     

煅烧的水滑石同时去除水体中砷和氟

为探讨水滑石类材料对水体中氟、砷离子的同时去除效果,采用共沉淀法合成(Mg∶Al=2∶1)纳米类水滑石(LDHs),用傅立叶转换红外光谱、电子扫描透射电镜、X射线晶体衍射等手段对合成的材料进行了表征,并研究纳米材料在不同初始浓度、pH、吸附时间、阴离子干扰条件下其同时除砷氟性能。结果表明,煅烧后的水滑石(LDOs)对砷最大吸附量为51.02 mg/g,对氟最大吸附量为36.63 mg/g。吸附动力学实验表明,煅烧水滑石对砷的吸附在前6 h内基本完成,对氟的吸附在前10 h内基本完成。砷氟共存溶液保持pH=4~10及pH=6~8时,水滑石分别对砷、氟保持良好的吸附效率。对比不同阴离子对水滑石共除砷氟效率的影响,水滑石除砷速率受到阴离子影响力大小为:HPO2-4CO2-3NO-3Cl-SO2-4;水滑石除氟速率受到阴离子影响力大小为:CO2-3HPO2-4SO2-4Cl-NO-3。材料再生循环利用4次后,对砷和氟的吸附效率均能达到90%以上。实验结果表明,所合成的水滑石是一种优秀的能共除砷氟的吸附剂。