Improving the dynamic response of frequency and power in a wind integrated power system by optimal design of compensated superconducting magnetic energy storage

The frequency deviation and power fluctuation need to be controlled in a wind-integrated power system (WIPS) for keeping the balance between system power generation and demand, which support the quality and stability of overall power system. The present paper addresses this problem while concerning the integration of intermittent wind power and load disturbance into the WIPS. With this intent, it proposes the compensated superconducting magnetic energy storage (CSMES) system with proportional integral derivative (PID) controller for improving the frequency and power deviation profile. A novel swarm intelligence-based artificial bee colony (ABC) algorithm is used for optimal design of PID-CSMES system. Robustness of the proposed ABC-based PID-CSMES control strategy is tested in WIPS under various disturbance patterns of load and wind power. To demonstrate the improved dynamic response, their simulation results are compared with particle swarm optimization-based PID-CSMES, PID with SMES, and only PID controller technique. The performance indices and transient response characteristics of frequency and power deviation are used to evaluate and compare the accuracy and efficiency of each controller. Stability of various system configurations is analyzed using eigenvalue location. Comparing the results of different controller in WIPS indicates a substantial improvement in the dynamic response of system frequency and power deviations by utilizing the proposed control strategy.     

冲击对蒸汽发生器传热管微动磨损行为的影响研究

目的 研究冲击对核电站蒸汽发生器传热管在高温蒸汽环境中微动磨损行为的影响规律与机理。方法 采用高温高压蒸汽环境冲击–滑移与纯滑移对比试验,研究冲击对蒸汽发生器690TT合金传热管微动磨损行为的影响。通过分析微观损伤结构区别,对比高、低磨损能量试验结果,明确冲击在微动磨损中的作用,获得传热管冲击–滑移复合微动磨损机理。结果 高温高压蒸汽环境中,复合微动磨损与纯滑移微动磨损相比,没有犁沟磨损特征,剥层特征占主导地位,微动磨损机制为剥层磨损。磨损能量越高,冲击引起的磨屑层脱落和基体开裂越多,磨损越严重。结论 冲击显著改变了传热管的微动磨损行为,在开展传热管服役安全评估中,应充分考虑纯滑移磨损与冲击–滑移复合微动磨损的显著差异。     

用于气体消毒的等离子体发生器的研究

利用微空心阴极放电的基本结构,设计了一款用于有毒气体消毒的等离子体发生器装置。对该装置的结构及其消毒机理进行了详细的论述,并对其放电特性进行了研究。实验研究发现:利用该装置能够对挥发性有毒气体甲烷、苯进行有效的消毒,还能够用作臭氧发生器。     

脉冲电晕技术在处理挥发性有机化合物中的应用研究

建立了利用脉冲电晕技术处理挥发性有机物的实验装置,选取苯作为代表物质进行实验研究,观察初始浓度、停留时间、注入能量、电源特性等参数对去除率的影响,并对反应副产物的成分进行分析测试.在输入电压为50 V,频率为20 Hz,气体体积流量为1 620mL/min,苯的初始质量浓度为76.8 mg/m3的实验条件下,苯的去除率达到61.4%.脉冲电晕技术处理低浓度有机废气效果较好.     

Design and analysis of artificial bee-colony-based MPPT algorithm for DFIG-based wind energy conversion systems

In this article, the proposed maximum power point tracking (MPPT) method is designed by taking rotor speed as an optimization problem, which is solved by artificial bee colony (ABC) algorithm to generate the maximum power output. The main advantage of this algorithm is that its optimal solution is independent of the initial positions and requirement of lesser number of control parameters, which leads to simple and robust MPPT algorithm than other algorithm. Furthermore, the hill climb search and particle swarm optimization-based MPPT algorithm are also discussed and the results obtained by these are compared to verify the effectiveness of proposed algorithm. Simulations for MPPT control along with doubly fed induction-generator-based wind energy conversion system is carried out in MATLAB/Simulink environment. Three statistical methods are used to evaluate the accuracy of each MPPT algorithm. All results are analyzed and compared under randomly selected wind as well as real wind speed configuration. Comparison of both numerical and simulation results under two different varying wind speed conditions strongly suggest that the proposed ABC-based MPPT algorithm is superior than other two MPPT algorithms.     

美国NIST元素汞发生器的基准溯源传递方法

综述了美国NIST元素汞发生器的基准溯源传递方法,通过在输出的汞标准气体中混合加入已知高纯度的201Hg0气体（201Hg2＋标准溶液还原雾化）,并采用同位素稀释电感耦合等离子体/质谱法（IDICP/MS）测量加标后201Hg/202Hg同位素丰度比例,计算出待溯源元素汞发生器输出的Hg0 质量浓度.该过程实现了从元素汞一级标准物质SRM 3133到201Hg2＋标准溶液,再到元素汞发生器输出标准气体的溯源传递,完成了从NIST元素汞基准到仪器供应商生产基准的一级溯源传递,为建立符合我国需求的元素汞溯源传递方法和形成元素汞发生器溯源传递能力提供借鉴.     

SWAT模型降水输入参数的改进研究

水文模型的运行和模拟精度,很大程度上依赖于输入参数的质量。论文通过不同途径获取的降水数据作为SWAT模型的输入参数,比较分析模型模拟精度。研究发现通常SWAT模型在模拟过程中选择的降水站点是固定的,如果某些年份缺失数据则会调用天气发生器,天气发生器基本可以满足SWAT模拟的需要,可以取得比较满意的结果。利用空间插值为缺乏降水观测的子流域提供降水输入参数,一定程度上提高了SWAT的模拟精度。不过在某些降水过程时空变率较大的情况下,空间插值的降水量往往偏低,导致SWAT模型对洪峰的模拟效果不好。     

全自动漏斗吸嘴式粉尘发生装置样机研制

基于粉尘浓度测定和粉尘分布规律、运移规律和沉降规律研究的需要,在气溶胶粉尘发生器的基础上,设计了由计算机控制的全自动漏斗吸嘴式粉尘发生装置.提出了该装置的设计原理、设计结构及运行操作方法.基于C++设计了该装置的控制程序软件包,利用软件包中的驱动控制程序,实现了在计算机上对粉尘发生装置的远程遥控.监测传感器可及时发现吸嘴口是否出现粉尘堵塞,故障传感器同步监测步进电机和搅拌电机,通过微型计算机分析故障并发出相应控制指令.操作过程中,通过对圈数、时长、粉尘用量和密度的设置,可发生1种或多种粒径粉尘,控制发尘浓度、分散度,实现粉尘连续供给.通过发尘效果检验,得出在不同作业工序下,无论是连续产尘的喷浆、凿岩作业,还是瞬间产尘的爆破作业,该装置都具有较好的模拟产尘效果,产尘的分散度、浓度与现场实测值基本一致,表明该装置的粉尘粒度分布控制、产尘流量控制等技术达到了预期效果,可为研究粉尘相关特性试验提供稳定可靠、数量可控的粉尘源.     

Improved Weather Generator Algorithm for Multisite Simulation of Precipitation and Temperature

The KnnCAD Version 4 weather generator algorithm for nonparametric, multisite simulations of temperature and precipitation data is presented. The K‐nearest neighbor weather generator essentially reshuffles the historical data, with replacement. In KnnCAD Version 4, a block resampling scheme is introduced to preserve the temporal correlation structure in temperature data. Perturbation of the reshuffled variable data is also added to enhance the generation of extreme values. The Upper Thames River Basin in Ontario, Canada is used as a case study and the model is shown to simulate effectively the historical characteristics at the site. The KnnCAD Version 4 approach is shown to improve on the previous versions of the model and offers a major advantage over many parametric and semiparametric weather generators in that multisite use can be easily achieved without making statistical assumptions dealing with the spatial correlations and probability distributions of each variable.     

蓄热式高温空气制备特性研究

在自行研制的蓄热式高温带压蒸气发生器上开展了高温空气制备实验。主要对不同换向周期及一个换向周期内工况条件下的高温空气的生产特性进行了研究,相应地,对不同换向周期条件下的高温带压蒸汽发生器的热回收效率进行了计算。结果表明:以空气为介质时30 s的换向周期为最佳换向周期。随着换向周期的增大,热回收效率快速降低。在一个切换周期内,随着换热时间的延长,空气预热温度逐渐降低,排烟温度总体较低,蓄热体对烟气热量的吸收效果良好。