Development of Anticorrosive Poly(Ether-Urethane) Amide Coatings from Linseed Oil: A Sustainable Resource

Polyetheramide(PEtA) resin was synthesized by the condensation polymerization of N,N-bis(2-hydroxy ethyl) linseed oil fatty amide diol (HELA) with resorcinol. It was further treated with different percentage of toluylene 2-4-diisocyanate (TDI) to obtain the urethane modified polyetheramide resins (UPEtA). The structural elucidation of PEtA and urethane modified polyetheramide(UPEtA) were carried out by FT-IR, ¹H-NMR and ¹³C-NMR spectroscopic techniques. These analyses confirm the formation of PEtA and UPEtA. Physico-chemical and physico-mechanical analysis were performed by standard laboratory methods. The resin composition UPEtA-24 showed best physico-mechanical properties with scratch hardness 2.0 kg, impact resistance 150 lb/in. and good bending ability. The thermal stability and curing behavior of polymers were respectively studied by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Thermal analysis shows that these coatings can be used safely upto 190 °C. The coatings of UPEtA resins were prepared on mild steel strips. The anticorrosive behavior of UPEtA coatings were investigated in acid, alkali, water and xylene. All the coatings exhibit good chemical resistance performance in acid, alkali, saline and organic solvents, while the resin UPEtA-24 shows the best performance.     

Optimisation of rainwater tank design from large roofs: A case study in Melbourne, Australia

Rainwater tanks for larger roof areas need optimisation of tank size, which is often not carried out before installation of these tanks. This paper presents a case study of rainwater tank evaluation and design for large roof areas, located in Melbourne, Australia, based on observed daily rainfall data representing three different climatic regimes (i.e. dry average, and wet years). With the aim of developing a comprehensive Decision Support Tool for the performance analysis and design of rainwater tanks, a simple spreadsheet based daily water balance model is developed using daily rainfall data, contributing roof area, rainfall loss factor, available storage volume, tank overflow and irrigation water demand. In this case study, two (185 m³ and 110 m³) underground rainwater tanks are considered. Using the developed model, effectiveness of each tank under different climatic scenarios are assessed. The analysis shows that both the tanks are quite effective in wet and average years, however less effective in dry years. A payback period analysis of the tanks is preformed which reveals that the total construction cost of the tanks can be recovered within 15-21 years time depending on tank size, climatic conditions and future water price increase rates. For the tanks, a relationship between water price increase rates and payback periods is developed. The study highlights the need for detailed optimisation and financial analysis for large rainwater tanks to maximise the benefits.     

The environmental Kuznets curve hypothesis for Bangladesh: the importance of natural gas,liquefied petroleum gas,and hydropower consumption

Environmental Science and Pollution Research - Mitigating environmental pollution has become a global agenda keeping the sustainability of socioeconomic and environmental development into...     

Use of fungi for the bioconversion of rice straw into cellulase enzyme

Cellulase production was carried out by solid state bioconversion (SSB) method using rice straw, a lignocellulosic material and agricultural waste, as the substrate of three Trichoderma spp. and Phanerochaete chrysosporium in lab-scale experiments. The results were compared to select the best fungi among them for the production of cellulase. Phanerochaete chrysosporium was found to be the best among these species of fungi, which produced the highest cellulase enzyme of 1.43 IU/mL of filter paper activity (FPase) and 2.40 IU/mL of carboxymethylcellulose activity (CMCase). The "glucosamine" and "reducing sugar" parameters were observed to evaluate the growth and substrate utilization in the experiments. In the case of Phanerochaete Chrysosporium, the highest glucosamine concentration was 1.60 g/L and a high concentration of the release of reducing sugar was measured as 2.58 g/L obtained on the 4th day of fermentation. The pH values were also recorded. The range of the pH was about 5.15 to 5.56 in the case of Phanerochaete Chrysosporium.     

Organochlorine,PCB, PAH,and metal concentrations in eggs of loggerhead sea turtles (Caretta caretta) from northwest Florida,USA

Abstract

Composite samples of unhatched and physically unaltered loggerhead sea turtle, Caretta caretta, eggs collected from 20 nests along northwest Florida were analyzed for organochlorine pesticides (OCPs), polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons (PAHs), and metals. Chemical analyses revealed that turtle eggs contained detectable amounts of metals, PAHs, and PCBs. Only one OCP, p, p'‐DDD, was detected, and its presence was restricted to eggs from two nesting sites. None of the PCB concentrations exceeded the Food and Drug Administration's (FDA) action limit. Concentrations of dioxin‐like PCB congeners, 105, 118, and 126, and total PCBs were also detected and are contributors to the toxic burden of loggerhead sea turtle eggs. Concentrations of PAHs, 1,2,5,6‐dibenzanthracene, 1‐methyl naphthalene, Cl‐naphthalene and naphthalene were variable at nesting sites. Comparison of mean metal burdens in eggs from different beaches suggested that no uniform geographic gradients exist. Presence of OCPs, PCBs, PAHs and metals and their additive or synergistic toxicity is a concern to loggerhead sea turtle eggs; however, additive or synergistic impacts for loggerhead sea turtles are largely undocumented.     

Emissions of volatile fatty acids from feed at dairy facilities

Recent studies suggest that dairy operations may be a major source of non-methane volatile organic compounds in dairy-intensive regions such as Central California, with short chain carboxylic acids (volatile fatty acids or VFAs) as the major components. Emissions of four VFAs (acetic acid, propanoic acid, butanoic acid and hexanoic acid) were measured from two feed sources (silage and total mixed rations (TMR)) at six Central California Dairies over a fifteen-month period. Measurements were made using a combination of flux chambers, solid phase micro-extraction fibers coupled to gas chromatography mass spectrometry (SPME/GC–MS) and infra-red photoaccoustic detection (IR-PAD for acetic acid only). The relationship between acetic acid emissions, source surface temperature and four sample composition factors (acetic acid content, ammonia-nitrogen content, water content and pH) was also investigated. As observed previously, acetic acid dominates the VFA emissions. Fluxes measured by IR-PAD were systematically lower than SPME/GC–MS measurements by a factor of two. High signals in field blanks prevented emissions from animal waste sources (flush lane, bedding, open lot) from being quantified. Acetic acid emissions from feed sources are positively correlated with surface temperature and acetic acid content. The measurements were used to derive a relationship between surface temperature, acetic acid content and the acetic acid flux. The equation derived from SPME/GC–MS measurements predicts estimated annual average acetic acid emissions of (0.7 + 1/?0.4) g m^?2 h^?1 from silage and (0.2 + 0.3/?0.1) g m^?2 h^?1 from TMR using annually averaged acetic acid content and meteorological data. However, during the summer months, fluxes may be several times higher than these values.     

Assessment of phenanthrene bioavailability in aged and unaged soils by mild extraction

It has become apparent that the threat of an organic pollutant in soil is directly related to its bioavailable fraction and that the use of total contaminant concentrations as a measure of potential contaminant exposure to plants or soil organisms is inappropriate. In light of this, non-exhaustive extraction techniques are being investigated to assess their appropriateness in determining bioavailability. To find a suitable and rapid extraction method to predict phenanthrene bioavailability, multiple extraction techniques (i.e., mild hydroxypropyl-β-cyclodextrin (HPCD) and organic solvents extraction) were investigated in soil spiked to a range of phenanthrene levels (i.e., 1.12, 8.52, 73, 136, and 335 μg g^− 1 dry soil). The bioaccumulation of phenanthrene in earthworm (Eisenia fetida) was used as the reference system for bioavailability. Correlation results for phenanthrene suggested that mild HPCD extraction was a better method to predict bioavailability of phenanthrene in soil compared with organic solvents extraction. Aged (i.e., 150 days) and fresh (i.e., 0 day) soil samples were used to evaluate the extraction efficiency and the effect of soil contact time on the availability of phenanthrene. The percentage of phenanthrene accumulated by earthworms and percent recoveries by mild extractants changed significantly with aging time. Thus, aging significantly reduced the earthworm uptake and chemical extractability of phenanthrene. In general, among organic extractants, methanol showed recoveries comparable to those of mild HPCD for both aged and unaged soil matrices. Hence, this extractant can be suitable after HPCD to evaluate risk of contaminated soils.     

Risk assessment and chemical decontamination of an oxime carbamate insecticide (methomyl) from eggplant, Solanum melongena L.

Methomyl, S-methyl (EZ)-N-(methylcarbamoyloxy)thioacetimidate, is a systemic insecticide chosen for the management of shoot and fruit borer, Leucinodes orbonalis G. Codex Alimentarious Commission has proposed a maximum residue limit (MRL) of 0.2 mg kg^???1 of methomyl, and there is a need to validate this value on eggplant. First + first-order model can explain the nonlinear dissipation pattern of methomyl conveniently in comparison to first-order kinetics. The preharvest intervals (PHI) of 27.3 and 35.3 days as obtained from first + first-order model for single and double doses would bring down the methomyl residue below MRL in actual practice. The respective half-lives were 6.6 and 7.8 days. On the other hand, first-order model suggests methomyl dissipated with a half-life value around 5 days and proposed PHIs of 6.57 and 8.57 days for single and double doses, which was far from reality. Hence, five different decontamination agents were chosen for the decontamination of methomyl from eggplant. Safety factors such as theoretical maximum daily intake and maximum permissible intake were used to evaluate risk assessment to human health. A 3-day waiting period for the both doses, following conventional agricultural practice and processing factor could not ensure sufficient margin of safety. Subjecting the data to a processing factor of 60% could not bring the residues below the proposed MRL by Codex. Methomyl is not found appropriate and effective for application in eggplant. Either the proposed MRL needs to be revised or good agricultural practice involving methomyl for plant protection in eggplant cultivation is questioned.     

Integration of novel hybrid composite discharge electrode with semi-pilot novel cross-flow electrostatic precipitator

ABSTRACT

Wet electrostatic precipitators (WESPs) are modern-era pollution control systems specifically designed to capture ultrafine particles as well as acid mist, highly resistive and sticky particles; however, this requires the use of expensive corrosion-resistant metal alloys. The work presented here is part of a continuing study at Ohio University aimed at reducing the cost of WESPs by using a novel combination of a polymer collector surfaces with a hybrid composite discharge electrode. In this study, a hybrid composite discharge electrode was tested, for the first time, inside a semi-pilot-scale experimental setup, with collection surfaces consists of a vertical array of strands. Particle laden gases were passed through this array of polymer ropes, which were kept wet by a small flow of water. The discharge electrodes were composite laminates of carbon fibers in a polymer matrix enclosing a metal mesh. The preliminary results showed that this new integrated system of composite discharge electrode and polymer collector surfaces can match or exceed the performance of a conventional metal alloy electrostatic precipitator (ESP) with metal discharge electrodes. There are additional advantages due to the system being compact, lightweight, and highly corrosion resistant.

Implications: This study focused on integrating and assessing performance of a novel hybrid composite electrode (HCE) inside semi-pilot novel cross-flow electrostatic precipitator at conditions typically observed in coal-fired power plant exhausts. The results were collected for particulate collection efficiencies and were compared with a rigid metal electrode. The HCE outperformed metal electrode by showing higher particulate collection efficiency. This result showcases substantial potential for these two new technologies (HCE and cross-flow system) as a substitute for conventional metal based wet ESPs.