紫外辐照-催化湿式过氧化氢氧化技术处理酸性大红GR染料废水

采用自制的负载型CuO-ZnO-CeO2/γ-Al2O3催化剂，常温常压下通过紫外辐照-催化湿式氧化技术处理酸性大红GR模拟染料废水。考察了催化剂加入量、H2O2加入量、废水pH、反应时间、初始酸性大红GR质量浓度等对废水脱色率的影响。实验得到最佳工艺条件为初始酸性大红GR质量浓度200mg/L，催化剂加入量10.0g/L，H2O2加入量2.0mL/L，废水pH4，反应时间2h。最佳工艺条件下废水脱色率达99.33%。     

Catalytic destruction of pentachlorobenzene in simulated flue gas by a V2O5-WO3/TiO2 catalyst

Pentachlorobenzene (PeCB) in simulated flue gas was destructed by a commercial V₂O₅-WO₃/TiO₂ catalyst in this study. The effects of reaction temperature, oxygen concentration, space velocity and some co-existing pollutants on PeCB conversion were investigated. Furthermore, a possible mechanism for the oxidation of PeCB over the vanadium oxide on the catalysts was proposed. Results show that the increase of gas hourly space velocity (GHSV) and the decrease of operating temperature both resulted in the decrease of PeCB removal over the catalyst, while the effect of the oxygen content in the range of 5-20% (v/v) on PeCB conversion was negligible. PeCB decomposition could be obviously affected by the denitration reactions under the conditions because of the positive effect of NO but negative effect of NH₃. The introduction of SO₂ caused the catalyst poisoning, probably due to the sulfur-containing species formed and deposited on the catalyst surface. The PeCB molecules were first adsorbed on the catalyst surface, and then oxidized into the non-aromatic acyclic intermediates, low chlorinated aromatics and maleic anhydride.     

氧化物催化剂对非热等离子体催化降解甲苯的影响

考察了在干燥气氛下不同氧化物催化剂对非热等离子体催化降解甲苯的影响。从甲苯降解率、碳平衡、CO2选择性和O3去除4个方面,对比了氧化物催化剂的介电性能、表面供氧能力和比表面积与多孔结构对反应产生影响的强弱。结果表明,催化剂的介电性能有利于甲苯降解率、碳平衡和O3产量的提高,但对CO2选择性和O3去除的影响极小;一定能量密度下,催化剂比表面积与多孔结构对CO2选择性和O3去除所产生的影响要强于介电性能;催化剂表面供氧能力可明显促进反应的进行,其对反应所产生的影响要强于比表面积与多孔结构。     

NiO-CuO/ZSM-5催化剂对催化裂化烟气的脱硫脱硝性能

采用浸渍法制备了不同NiO和CuO质量分数的NiO-CuO/ZSM-5催化剂，并以CH4为还原剂研究了NiO-CuO/ZSM-5催化剂对催化裂化烟气的脱硫脱硝活性。XRD分析结果表明，NiO质量分数为4%、CuO质量分数为6%的催化剂4%NiO-6%CuO/ZSM-5中的ZSM-5结构完好，CuO和NiO高度分散在ZSM-5骨架中，表明具有较好的催化活性。4%NiO-6%CuO/ZSM-5的脱硫脱硝起活温度均较低，无氧条件下最高NO转化率和SO2转化率分别为94.7%和95.9%，O2体积分数为1.0%时的NO转化率和SO2转化率分别为97.7%和89.0%。     

火电厂SCR烟气脱硝催化剂特性及其应用

SCR工艺是火电厂的主流烟气脱硝技术，催化剂是SCR脱硝工艺的核心。通过对不同型式催化剂特性及其应用的对比分析，得出了蜂窝式催化剂综合性能较优的结论，并对不同烟气条件下的催化剂选择提出了建议.     

A preliminary process design and economic assessment of a catalyst rejuvenation process for waste disposal of refinery spent catalysts

Spent hydroprocessing catalysts from refineries have been classified as hazardous solid waste by the United States Environmental Protection Agency (USEPA), refiners must find a viable but economical solution to solve this serious environmental issue. Catalyst rejuvenation is an attractive option for minimizing the environmental problems associated with spent catalysts. In this study, a preliminary design for such a process and the corresponding economic analysis are performed to assess the proposed catalyst rejuvenation process for metal-fouled spent catalysts generated in residue hydroprocessing units. The scenarios used in the economic assessment are based on three options of process synthesis and two operator modes. It is found that the option of rejuvenating medium and lightly fouled spent catalyst produced by the refinery will be the best solution for refiners, both environmentally and economically.     

Glucose production from hydrolysis of cellulose over a novel silica catalyst under hydrothermal conditions

A novel silica catalyst was synthesized by evaporation-induced self-assembly (EISA) method and tested for the catalytic selective hydrolysis of cellulose to glucose. This silica catalyst exhibited a higher catalytic activity than other oxides prepared by the same method, such as ZrO₂, TiO₂, and Al₂O₃. Using silica as a catalyst, cellulose was selectively hydrolyzed into glucose with a glucose yield as high as 50% under hydrothermal conditions without hydrogen gas. The silica catalyst was characterized by Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results of temperature-programmed desorption of ammonia (NH₃-TPD) and textural properties indicated that the synergistic effect between strong acidity and a suitable pore diameter of the silica catalyst may be responsible for its high activity. In addition, the catalyst was recyclable and showed excellent stability during the recycle catalytic runs.     

Effects of WOx modification on the activity, adsorption and redox properties of CeO2 catalyst for NOx reduction with ammonia

A series of WO₃/CeO₂ (WOx/CeO₂) catalysts were synthesized by wet impregnation of ammonium metatungstate on a CeO₂ support. The resulting solid acid catalysts were characterized by X-ray diffraction (XRD), UV-Vis spectroscopy (UV-Vis), Raman spectroscopy (Raman), in-situ Fourier transform infrared spectroscopy (in-situ FT-IR) of ammonia adsorption, NH₃-TPD, H₂ temperature-programmed reduction (H₂-TPR), NH₃/NO oxidation and activity measurements for NOx reduction by NH₃ (NH₃-SCR). The results show that polytungstate (WOx) species are the main species of tungsten oxide on the surface of ceria. The addition of tungsten oxide enhances the Brönsted acidity of ceria catalysts remarkably and decreases the amount of surface oxygen on ceria, with strong interaction between CeO₂ and WOx. As a result, the N₂ selectivity of NH₃ oxidation and NH₃-SCR at high temperatures (> 300℃) is enhanced. Therefore, a wide working temperature window in which NOx conversion exceeds 80% (NOx conversion > 80%) from 200 to 450℃, is achieved over 10 wt.% WOx/CeO₂ catalyst. A tentative model of the NH₃-SCR reaction route on WOx/CeO₂ catalysts is presented.     

锰铈脱硝催化剂的制备及其再生性能研究

采用等体积浸渍法制备了一系列Mn-Ce-Ox复合氧化物脱硝催化剂用于NH3选择性催化还原(NH3-SCR)NO。考察了Mn/Ce摩尔比、焙烧温度、H2O和SO2对Mn-Ce-Ox复合氧化物脱硝催化剂活性的影响及催化剂中毒再生性能。结果表明:当NH3:NO=1:1,空速为5 000 h-1,550℃焙烧制得的Mn/Ce摩尔比为5∶1的Mn-Ce-Ox复合脱硝催化剂活性最佳,活性温度窗口为100~260℃,在此温度区间内催化剂活性大于90%。200℃时,Mn-Ce-Ox复合催化剂活性最高为97.84%;在10%(V/V)H2O蒸汽和300×10-6SO2共存条件下,200℃时,催化剂活性在开始反应2.5 h内迅速下降至53%左右,并在之后的6 h内没有明显变化;中毒催化剂经常温水洗再生处理、质量分数为3%的硝酸溶液再生处理和550℃焙烧2 h再生处理后200℃活性均能恢复到90%以上,其中中毒催化剂经质量分数为3%硝酸处理后活性恢复率最高。     

铁氮掺杂碳纳米管/纤维复合物制备及其催化氧还原的效果

阴极催化剂是影响微生物燃料电池(microbial fuel cell,MFC)性能的关键因素.通过研究制备成本低廉、氧还原反应(ORR)催化活性高的阴极催化剂来替代Pt/C对于实现MFC规模化应用具有重大意义.研究采用化学气相沉淀法,以三聚氰胺作为碳氮前驱物、以黑珍珠2000或乙炔炭黑作为碳源,外加醋酸亚铁作为铁前驱物,合成了两种铁氮掺杂碳纳米管/纤维复合物(FeNCB和FeNCC),作为MFC的阴极催化剂.通过循环伏安法和旋转圆盘-环电极分析FeNCB、FeNCC和Pt/C的ORR催化活性的差异,并用MFC验证其差异.结果表明,FeNCB性能与Pt/C相当,优于FeNCC,其催化路径是通过4电子途径催化氧还原反应;MFC-FeNCB性能略优于MFC-Pt/C,显著优于MFC-FeNCB有助于MFC的扩大化,其最大功率密度为1 212.8mW·m~(-2),开路电压为0.875 V,电池稳定电压为(0.500±0.025)V.用X射线衍射、X射线光电子光谱、拉曼光谱等进一步分析显示,复合物中碳纳米管管径的大小、铁氮掺杂的类型和含量以及氧含量是引起制备的复合物催化氧还原性能差异的原因所在.