富氧条件下SnO2/Al2O3催化剂上丙烯选择性还原NOx的研究

考察了分别用浸渍法、共沉淀法和溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂上丙烯选择性还原NO_x的催化活性,发现制备方法与Sn的负载量对其活性有重要影响.溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂活性最高,Sn的最佳负载量为5%.与浸渍法和共沉淀法制备的5%SnO₂/Al₂O₃催化剂相比,溶胶-凝胶法制备的5%SnO₂/Al₂O₃催化剂受水蒸汽的抑制作用较弱,并且在水和SO₂共存的条件下活性最高.此外,反应气中丙烯及氧气浓度的增加有利于NO_x转化率的提高.     

Studies on catalytic reduction of nitrate in groundwater

Catalytic reduction of nitrate in groundwater by sodium formate over the catalyst was investigated. Pd-Cu/γ-Al₂O₃ catalyst was prepared by impregnation and characterized by brunauer-emmett-teller (BET), inductive coupled plasma (ICP), X-ray diffraction (XRD), transmission electron microscopy (TEM) and energy dispersive X-ray (EDX). It was found that total nitrogen was effectively removed from the nitrate solution (100 mg/L) and the removal efficiency was 87%. The catalytic activity was affected by pH, catalyst amount used, concentration of sodium formate, and initial concentration of nitrate. As sodium formate was used as reductant, precise control in the initial pH was needed. Excessively high or low initial pH (7.0 or 3.0) reduced catalytic activity. At initial pH of 4.5, catalytic activity was enhanced by reducing the amount of catalyst, while concentrations of sodium formate increased with a considerable decrease in N₂ selectivity. In which case, catalytic reduction followed the first order kinetics. Translated from Acta Scientiae Circumstantiae, 2006, 26(4): 567–571 [译自: 环境科学学报]     

Catalytic activity of cerium-doped Ru/Al2O3 during ozonation of dimethyl phthalate

In this paper, factors influencing the mineralization of dimethyl phthalate (DMP) during catalytic ozonation with a cerium-doped Ru/Al₂O₃ catalyst were studied. The catalytic contribution was calculated through the results of a comparison experiment. It showed that doping cerium significantly enhanced catalytic activity. The total organic carbon (TOC) removal over the doped catalyst at 100 min reached 75.1%, 61.3% using Ru/Al₂O₃ catalyst and only 14.0% using ozone alone. Catalytic activity reached the maximum when 0.2% of ruthenium and 1.0% of cerium were simultaneously loaded onto Al₂O₃ support. Results of experiments on oxidation by ozone alone, adsorption of the catalyst, Ce ion’s and heterogeneous catalytic ozonation confirmed that the contribution of heterogeneous catalytic ozonation was about 50%, which showed the obvious effect of Ru-Ce/Al₂O₃ on catalytic activity. __________ Translated from China Environmental Science, 2006, 26(4): 445–448 [译自: 中国环境科学]     

Characterization and performance of Pt/SBA-15 for low-temperature SCR of NO by C3H6

Pt supported on mesoporous silica SBA-15 was investigated as a catalyst for low temperature selective catalytic reduction(SCR) of NO by C 3 H 6 in the presence of excess oxygen.The prepared catalysts were characterized by means of XRD,BET surface area,TEM,NO-TPD,NO/C 3 H 6-TPO,NH 3-TPD,XPS and 27 Al MAS NMR.The effects of Pt loading amount,O 2 /C 3 H 6 concentration,and incorporation of Al into SBA-15 have been studied.It was found that the removal efficiency increased significantly after Pt loading,but an optimal loading amount was observed.In particular,under an atmosphere of 150 ppm NO,150 ppm C 3 H 6,and 18 vol.% O 2,0.5% Pt/SBA-15 showed remarkably high catalytic performance giving 80.1% NOx reduction and 87.04% C 3 H 6 conversion simultaneously at 140°C.The enhanced SCR activity of Pt/SBA-15 is associated with its outstanding oxidation activities of NO to NO 2 and C 3 H 6 to CO 2 in low temperature range.The research results also suggested that higher concentration of O 2 and higher concentration of C 3 H 6 favored NO removal.The incorporation of Al into SBA-15 improved catalytic performance,which could be ascribed to the enhancement of catalyst surface acidity caused by tetrahedrally coordinated AlO 4.Moreover,the catalysts could be easily reused and possessed good stability.     

Novel CeO2@TiO2 core–shell nanostructure catalyst for selective catalytic reduction of NOx with NH3

The CeO₂@TiO₂ core–shell nanostructure catalyst prepared by a two-step hydrothermal method was used for selective catalytic reduction (SCR) of NOx with NH₃ in this study. The catalyst presented the obvious core–shell structure, and the shell was amorphous TiO₂ which could protect the active center from the SO₂ erosion. The catalyst showed high activity and stability, excellent N₂ selectivity and superior SO₂ resistance and H₂O tolerance. Characterizations such as TEM, HR-TEM, XRD, BET, XPS, NH₃-TPD, and H₂-TPR were carried out. The results indicated that the catalyst had large surface area and the active sites were well dispersed on the surface. The NH₃-TPD, H₂-TPR and XPS results implied that its increased SCR activity might be due to the enhancement of NH₃ chemisorption and the increase of active oxygen species, both of which were conductive to NH₃ activation. The excellent catalytic performance suggests that it is a promising candidate for SCR catalyst.     

Cu-Al2O3中骨架铜类芬顿催化去除水中有机污染物

为解决传统铁基芬顿催化剂在水体通常酸碱(pH6)条件下活性低的问题,采用简单共沉淀法制备了Cu掺杂的Al_2O_3类芬顿催化剂.通过X射线衍射(XRD)、X射线光电子能谱(XPS)和紫外可见(UV-vis)吸收光谱分析表明,Cu-Al_2O_3中铜掺杂的质量分数低于4.77%时,催化剂中铜主要以Cu~(2+)和Cu~+的形式共存于Al_2O_3的骨架结构中,形成Al—O—Cu键;过量的铜掺杂会导致外骨架铜物种如铜氧化物团簇的存在.以难降解有机污染物2-氯苯酚(2-chlorophenol,2-CP)和染料罗丹明B(Rhodamine B,Rh B)为目标污染物,对Cu-Al_2O_3的类芬顿催化性能进行了详细地研究.结果表明,骨架铜物种在中性温和条件下对2-CP和Rh B显示出很高的催化去除效率和稳定性,反应2 h,Cu-Al_2O_3(Cu质量分数4.77%)对2-CP的去除率达到54%,相应的TOC去除率达到49%,而铜离子溶出浓度仅为0.025 5 mg·L-1,而Cu-Al_2O_3(Cu质量分数7.58%)由于外骨架铜的存在导致催化活性增加缓慢和稳定性下降.ESR测试结果表明,·OH和HO_2~-/O_2~-·是反应中主要的活性物种.     

δ-MnO2 decorated layered double oxides in-situ grown on nickel foam towards electrothermal catalysis of n-heptane

Energy-saving and efficient monolithic catalysts are hotspots of catalytic purification of industrial gaseous pollutants. Here, we have developed an electrothermal catalytic mode, in which the ignition temperature required for the reaction is provided by Joule heat generated when the current flows through the catalyst. In this paper, Mn/NiAl/NF, Mn/NiFe/NF and Mn/NF metal-based monolithic catalysts were prepared using nickel foam (NF) as the carrier for thermal and electrothermal catalysis of n-heptane. The results indicated that Mn-based monolithic catalysts exhibit high activity in thermal and electrothermal catalysis. Mn/NiFe/NF achieve conversion of n-heptane more than 99% in electrothermal catalysis under a direct-current (DC) power of 6 W, and energy-saving is 54% compared with thermal catalysis. In addition, the results indicated that the introduction of NiAl (or NiFe) greatly enhanced the catalytic activity of Mn/NF, which attributed to the higher specific surface area, Mn³⁺/Mn⁴⁺, Ni³⁺/Ni²⁺, adsorbed oxygen species (O_ads)/lattice oxygen species (O_latt), redox performance of the catalyst. Electrothermal catalytic activity was significantly higher than thermal catalytic activity before complete conversion, which may be related to electronic effects. Besides, Mn/NiFe/NF has good cyclic and long-term stability in electrothermal catalysis. This paper provided a theoretical basis for applying electrothermal catalysis in the field of VOCs elimination.     

Study on methane conversion to syngas over nano Pt-CeO2-ZrO2/MgO catalysts: Structure and catalytic behavior of catalysts prepared by using ion exchange resin method

Nano Pt-Ce0₂-Zr0₂/MgO catalysts with 0.8 wt.% Pt, 3.0 wt.% Ce0₂ and 3.0 wt.% Zr0₂ were prepared by wet impregnation mothod. Support MgO was obtained using ion exchange resin method or using commercial MgO. S_BET, XRD, TEM and C0₂-TPD were used to characterize the supports and catalysts. CH₄-C0₂ reforming to synthesis gas was performed to test the catalytic behavior of the catalysts. The catalysts prepared using ion exchange resin exhibited more regular structure, more basic sites and higher stability of Pt and MgO than prepared from commercial MgO. At 1073 K, atmospheric pressure, and at high gas hourly space velocity of 36,000 mL/(g-hr) with a stoichiometric feed of CH₄ and C0₂, the catalyst supported on the MOH(GD)-IE showed a higher and more stable activity for CH₄-C0₂ reforming reaction than the catalyst prepared using commercial MgO. The characterisation results demonstrated that the high activity and stability of the catalyst stem from the high dispersion of Pt, the stable structure and the high resistance to carbon deposition on the catalyst.     

Removal of formaldehyde over MnxCe1-xO2 catalysts: Thermal catalytic oxidation versus ozone catalytic oxidation

MnxCe1- xO2（x： 0.3–0.9） prepared by Pechini method was used as a catalyst for the thermal catalytic oxidation of formaldehyde（HCHO）. At x = 0.3 and 0.5, most of the manganese was incorporated in the fluorite structure of Ce O2 to form a solid solution. The catalytic activity was best at x = 0.5, at which the temperature of 100% removal rate is the lowest（270°C）. The temperature for 100% removal of HCHO oxidation is reduced by approximately 40°C by loading 5 wt.% Cu Oxinto Mn0.5Ce0.5O2. With ozone catalytic oxidation, HCHO（61 ppm） in gas stream was completely oxidized by adding 506 ppm O3 over Mn0.5Ce0.5O2 catalyst with a GHSV（gas hourly space velocity） of 10,000 hr-1at 25°C. The effect of the molar ratio of O3 to HCHO was also investigated. As O3/HCHO ratio was increased from 3 to 8, the removal efficiency of HCHO was increased from 83.3% to 100%. With O3/HCHO ratio of 8, the mineralization efficiency of HCHO to CO2 was 86.1%. At 25°C, the p-type oxide semiconductor（Mn0.5Ce0.5O2） exhibited an excellent ozone decomposition efficiency of 99.2%,which significantly exceeded that of n-type oxide semiconductors such as Ti O2, which had a low ozone decomposition efficiency（9.81%）. At a GHSV of 10,000 hr-1, [O3]/[HCHO] = 3 and temperature of 25°C, a high HCHO removal efficiency（≥ 81.2%） was maintained throughout the durability test of 80 hr, indicating the long-term stability of the catalyst for HCHO removal.     

低温等离子体结合锰基催化剂去除乙酸乙酯的研究

利用固态法和溶胶-凝胶法分别制备了钙钛矿（LaMnO₃）和八面体分子筛（OMS）两种锰基催化剂,在不同工况（输入电压、初始浓度、停留时间和催化剂放置量）条件下考察了等离子体催化对乙酸乙酯的降解特性.结果发现,锰基催化剂的加入显著提高了乙酸乙酯的去除率,减少了副产物的生成,并且OMS的催化活性高于LaMnO₃;此外,乙酸乙酯去除率随着电压的升高而增加,随着污染物初始浓度的增大而减少,并随停留时间的增长而变大;催化剂放置量为0.2 g时催化效果最佳.OMS催化剂在等离子体催化长期运行过程中表现出较好的稳定性.基于X射线衍射（XRD）、X射线光电子能谱（XPS）、H₂程序升温还原（H₂-TPR）、比表面积测试（BET）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）等手段对锰基催化剂物理化学性质的分析表明,OMS具有较高的催化活性主要归功于其拥有更高比例的Mn⁴⁺/（Mn³⁺+Mn⁴⁺）和吸附氧（O_ads）/晶格氧（O_latt）.     

Enhanced catalytic complete oxidation of 1,2-dichloroethane over mesoporous transition metal-doped γ-Al2O3

High-surface-area mesoprous powders of γ-Al₂O₃ doped with Cu^2 +, Cr^3 +, and V^3 + ions were prepared via a modified sol–gel method and were investigated as catalysts for the oxidation of chlorinated organic compounds. The composites retained high surface areas and pore volumes comparable with those of undoped γ-Al₂O₃ and the presence of the transition metal ions enhanced their surface acidic properties. The catalytic activity of the prepared catalysts in the oxidation of 1,2-dichloroethane (DCE) was studied in the temperature range of 250–400°C. The catalytic activity and product selectivity were strongly dependent on the presence and the type of dopant ion. While Cu^2 +- and Cr^3 +-containing catalysts showed 100% conversion at 300°C and 350°C, V^3 +-containing catalyst showed considerably lower conversion. Furthermore, while the major products of the reactions over γ-alumina were vinyl chloride (C₂H₃Cl) and hydrogen chloride (HCl) at all temperatures, Cu- and Cr-doped catalysts showed significantly stronger capability for deep oxidation to CO₂.     

Pt/CeO2催化氧化甲苯反应机制研究

采用浸渍法制备了Pt/CeO_2和Pt/Al2O_3催化剂,并通过XRD、BET、ICP-OES、H2-TPR、XPS等手段表征其物理化学性质.结果发现,Pt/CeO_2和Pt/Al2O_3催化剂上Pt负载量约为0.6%,Al2O_3载体上Pt颗粒尺寸更小,Pt/CeO_2的可还原性更强.甲苯催化氧化活性评价结果表明,Pt/CeO_2催化剂表现出更好的催化活性,T50=170℃,T90=190℃.通过UV-Raman、甲苯TPD、GC/MS、In-situ FTIR等手段进一步研究发现,Pt/CeO_2活化甲苯及反应供氧的机制与Pt/Al2O_3存在区别,其活性更好是因为:(1)负载在CeO_2表面存在高电子密度的Pt原子,具有更强的活化甲苯能力,可以直接使苯基和甲基间的C—C链发生断裂;(2)Pt的负载促进了CeO_2氧空位形成,进一步提高了CeO_2的储氧性能,加速氧循环.除了Pt解离气相氧之外,CeO_2还可以提供活性氧物种参与催化氧化甲苯的反应,进一步提高甲苯催化氧化效率.     

Heterogeneous Fenton-like degradation of 4-chlorophenol using iron/ordered mesoporous carbon catalyst

Ordered mesoporous carbon supported iron catalysts(Fe/OMC) were prepared by the incipient wetness impregnation method and investigated in Fenton-like degradation of 4-chlorophenol(4CP) in this work. XRD and TEM characterization showed that the iron oxides were well dispersed on the OMC support and grew bigger with the increasing calcination temperature. The catalyst prepared with a lower calcination temperature showed higher decomposition efficiency towards 4CP and H2O2, but more metals were leached. The effect of different operational parameters such as initial pH, H2O2 dosage, and reaction temperature on the catalytic activity was evaluated. The results showed that 96.1% of 4CP and 47.4% of TOC was removed after 270 min at 30°C, initial pH of 3 and 6.6 mmol/L H2O2. 88% of 4CP removal efficiency was retained after three successive runs, indicating Fe/OMC a stable catalyst for Fenton reaction. 4CP was degraded predominately by the attack of hydroxyl radical formed on the catalyst surface and in the bulk solution due to iron leaching. Based on the degradation intermediates detected by high performance liquid chromatography, possible oxidation pathways were proposed during the 4CP degradation.     

有机物多相光催化降解反应中催化剂固定化技术研究

以ＴｉＣｌ４和异丙醇为原料,通过化学反应将钛组分以键合方式引入载体多孔硅胶颗粒的表面,经高温处理提高活性,制备出的催化剂以甲基检溶液的脱色反应有很好的光催化活性,与相同量的粉末ＴｉＯ２作用相比,活性升高,经分析测定催化剂颗粒上有３１．０５％的钛成分且表面仍保持硅胶颗粒的骨架结构,具有大比表面和高分散性的优点,利用该方法即可以制备大颗粒载体型ＴｉＯ２催化剂,也可能进一步解决用于实际太阳光废水处理装置     

纳米Fe3O4/CeO2-H2O2非均相类Fenton体系对3,4-二氯三氟甲苯的降解

以浸渍法制备的新型纳米Fe3O4/Ce O2为催化剂,3,4-二氯三氟甲苯(3,4-DCBTE)为目标污染物,在Fe3O4/Ce O2-H2O2非均相类Fenton体系中对目标污染物的降解进行研究,考察催化剂的催化效果和温度、p H、H2O2投加量等因素对催化剂催化效果的影响.结果表明,以纳米Fe3O4/Ce O2作为催化剂的非均相类Fenton体系对3,4-二氯三氟甲苯的处理效果极佳;随着温度的升高,纳米Fe3O4/Ce O2的催化效果不断提高;在偏酸性环境中,p H越低催化效果越好,p H=2时反应去除效率可达96.67%;随着H2O2投加量的增加,3,4-二氯三氟甲苯的降解效率先提高后降低,投加量为15 mg·L-1时去除效果最好可达99.47%;随着催化剂投加量的增加,同样出现了处理效果先升高后降低的现象,投加量为0.5 g·L-1时催化效果最好可达99.64%.在以纳米Fe3O4/Ce O2为催化剂的非均相类Fenton体系中,3,4-二氯三氟甲苯的降解符合一级反应动力学,反应所需活化能较低只需30.26 k J·mol-1.     

N2O decomposition over K/Na-promoted Mg/Zn-Ce-cobalt mixed oxides catalysts

Three groups of cobalt mixed oxide catalysts（Mg/Zn-Co, Mg/Zn-Ce-C, K/Na-Mg/Zn-Ce-Co）were prepared by sol-gel or impregnation methods. The synergistic effects of transition metal, rare earth metal and alkali metal on cobalt mixed catalysts for nitrous oxide（N2O）decomposing to N2 and O2were investigated. The experimental results revealed that the catalytic activity for N2 O decomposition was promoted as Co2＋was replaced partially by Zn2＋/Mg2＋, moreover, the characterization analysis by XRD and XPS showed that Zn2＋/Mg2＋replaced Co2＋successfully into the spinel structure of Co3O4 and promoted significantly the catalytic activity. Especially, the addition of CeO2 and K2O/Na2O decreased the binding energy and resulted in an increase in the density of the electron cloud around Co and an improvement of the catalytic activity. Of the investigated cobalt mixed catalysts, the best catalytic activity was shown by 2% K-Zn0.5-Ce0.05-Co catalyst.     

Oxidation of diesel soot on binary oxide CuCr(Co)-based monoliths

Binary oxide systems (CuCr₂O₄, CuCo₂O₄), deposited onto cordierite monoliths of honeycomb structure with a second support (finely dispersed Al₂O₃), were prepared as filters for catalytic combustion of diesel soot using internal combustion engine's gas exhausts (O₂, NO_x, H₂O, CO₂) and O³ as oxidizing agents. It is shown that the second support increases soot capacity of aforementioned filters, and causes dispersion of the particles of spinel phases as active components enhancing thereby catalyst activity and selectivity of soot combustion to CO₂. Oxidants used can be arranged with reference to decreasing their activity in a following series: O₃ >> NO₂ > H₂O > NO > O₂ > CO₂. Ozone proved to be the most efficient oxidizing agent: the diesel soot combustion by O₃ occurs intensively (in the presence of copper chromite based catalyst) even at closing to ambient temperatures. Results obtained give a basis for the conclusion that using a catalytic coating on soot filters in the form of aforementioned binary oxide systems and ozone as the initiator of the oxidation processes is a promising approach in solving the problem of comprehensive purification of automotive exhaust gases at relatively low temperatures, known as the "cold start" problem.     

以堇青石蜂窝陶瓷为载体的新型钒氧化物脱氮催化剂研究

以TiO₂/Al₂O₃/堇青石蜂窝陶瓷为载体,以V₂O₅-MoO₃-WO₃为活性组分,用于氨法选择性催化还原烟气中NO的新型催化剂,并对该催化剂的活性性能和微观结构进行了评价和表征.同时,将该催化剂的活性性能与其它几种活性组分相同但载体、制备方法、结构不同的催化剂进行了对比.对比结果表明,该新型催化剂能取得最好的选择性催化还原氮氧化物催化性能BET、FT IR、XPS表征实验结果表明,其高催化活性得益于大比表面积及大孔体积,而TiO₂/Al₂O₃/堇青石蜂窝陶瓷载体及其制备方法对获得好的催化剂构型起了至关重要的作用.     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

Highly catalytic activity of Mn/SBA-15 catalysts for toluene combustion improved by adjusting the morphology of supports

Rod-like, hexagonal and fiber-like SBA-15 mesoporous silicas were synthesized to support MnO_x for toluene oxidation. This study showed that the morphology of the supports greatly influenced the catalytic activity in toluene oxidation. MnO_x supported on rod-like SBA-15(R-SBA-15) displayed the best catalytic activity and the conversion at 230°C reached more than 90%, which was higher than the other two catalysts. MnO_x species consisted of coexisting MnO_2 and Mn_2O_3 on the three kinds of SBA-15 samples. Large amounts of Mn_2O_3 species were formed on the surface and high oxygen mobility was obtained on MnO_x supported on R-SBA-15, according to the H_2 temperature programmed reduction(H_2-TPR)and X-ray photoelectron spectroscopy(XPS) results. The Mn/R-SBA-15 catalyst with greater amounts of Mn_2O_3 species possessed a large amount of surface lattice oxygen, which accelerated the catalytic reaction rate. Therefore, the surface lattice oxygen and high oxygen mobility were critical factors on the catalytic activity of the Mn/R-SBA-15 catalyst.