单芯铜线过电流故障电弧熔痕的微观特征研究*

为准确认定电气火灾中过电流故障，模拟4~7倍额定电流（Ie）条件下单芯铜导线过电流故障，利用光学显微镜和扫描电子显微镜（SEM）分析过电流故障电弧熔痕的组织特征，并结合Image-Pro Plus软件测定晶粒直径、周长和面积，探究金相组织的量化判据和变化规律。结果表明:当I＝4Ie时，过电流故障电弧熔痕的金相组织主要为方向性较强的树枝晶；当I＝5Ie，6Ie时，金相组织内树枝晶占比减小，胞状晶占比升高；当I＝7Ie时，方向性较弱的胞状晶占主导。随着电流增加，晶粒的平均直径、周长和面积均呈增长趋势。通过火灾案例分析可知，实验结果与现场的电弧熔痕组织特征基本相符，验证火灾事故原因为过电流故障。     

矿热炉炉壳安装作业危险性分析

为减少事故损失,必须对矿热炉安装施工危险源进行分析。基于此,对矿热炉安装工序中最重要工序炉壳安装应用作业危险性分析进行分析。将炉壳安装作业分成3大部分,用鱼刺图分析方法进行分析,总结出矿热炉炉壳安装中事故发生的主要原因并提出对策措施,以预防和减少事故的发生。     

太阳模拟器大功率短弧氙灯放电特性试验测试

目的增强太阳模拟器氙灯驱动运行的可靠性,给太阳模拟器研制提供技术保障,针对太阳模拟器大功率短弧氙灯放电特性进行试验研究。方法设计太阳模拟器的大功率短弧氙灯放电特性测试方法,然后通过理论计算和实际测试验证氙灯电源初始电流对短弧氙灯放电特性的影响,并采用增设优化电路的方法对其放电特性进行改善。结果在初始电流为70 A和120 A两种情况下,弧光放电电流到达谷值以后的电流稳定度分别为1.8616和0.9867,增设优化电路后,再次进行短弧氙灯放电特性测量,将初始电流降低到60 A,而稳定度可达到0.5409。结论改善后的电路基本可实现短弧氙灯放电理想状态,完成了对短弧氙灯进入电流击穿阶段后形成的稳定弧光放电电流特性的优化,大大提升了氙灯点灯成功率,为增强太阳模拟器可靠性提供了试验支持。     

新型矿用圆弧形薄壁防冲吸能装置屈曲特性数值分析*

为解决支架面对冲击地压产生的强冲作用容易失效、失稳的难题,针对现有矿用防冲吸能装置存在的不足,提出1种新型矿用圆弧形薄壁防冲吸能装置。采用ABAQUS有限元数值模拟方法对新型防冲吸能装置与原有方形预折纹薄壁装置进行对比分析,同时研究新型防冲吸能装置在不同壁厚和不同轴向模块堆积个数情况下的屈曲特性。结果表明:圆弧形薄壁装置相比于方形折纹薄壁装置在相同厚度情况下其总吸能提升近20%,比吸能提高63%,装置防冲优势明显;在装置高度不变的情况下增加模块轴向堆积个数可有效降低压溃峰值荷载、荷载波动系数,增加平均压溃荷载;随着装置薄壁厚度降低,压溃峰值荷载、压溃平均荷载、总吸能与比吸能均降低,荷载波动系数增加,曲线波动性变大。     

Microstructure of 2205 duplex stainless steel joint in submerged arc welding by post weld heat treatment

The 2205 duplex stainless steel (DSS) is of both good properties austenitic steel and ferritic steel, which applies to the shipbuilding industry usually. In this paper, the OM, XRD and microhardness test methods are used to analyze the variation of submerged arc welded (SAW) joints with and without post weld heat treatment (PWHT). The research results show that the σ phase disappear in the fusion edge zone near heat affect zone (HAZ) and an increase in the welded center zone during the follow-up PWHT, while the amount of γ phase is decreased in the welded center zone with PWHT. A segregation distribution of some second phases is also found in the welded center zone after PWHT. There have two pick values of microhardness arise in the fusion edge zone and the welded center zone separately without PWHT. However, a maximum value of microhardness at the fusion edge zone near HAZ is disappeared and the other is still held at the welded center zone during PWHT. It can be attributed to the changes of second phases, element diffusions and particle segregation during PWHT. A developing mechanism is issued to demonstrate the second phases transferring of the 2205 DSS SAW joints by PWHT.     

三种流速下高强钢与微弧氧化钛电偶腐蚀研究

目的研究三种流速下微弧氧化钛和高强钢的电偶腐蚀行为。方法在面积比为1:1情况下进行1,3,7 m/s流速下的电化学测试和电偶腐蚀试验研究。结果随着流速的增大,偶合电流、总腐蚀速率和电偶腐蚀速率增大。当流速为7 m/s时,高强钢总腐蚀速率和电偶腐蚀速率分别达到8.64 mm/a和0.39 mm/a,与静态相比分别增大146倍和15.6倍,与1 m/s流速下相比分别增大8.6倍和5倍。结论在面积比为1:1时,冲刷腐蚀速率远大于电偶腐蚀速率。     

活性炭吸附和脱附-等离子体氧化净化有机废气的研究

根据滑动弧放电等离子体适于降解高浓度有机物废气的特性,结合活性炭吸附法,提出了吸附器的吸附浓缩和热脱附-等离子体氧化净化有机废气的方法。在活性炭吸附过程中,最初2 h内甲苯净化率达到100%,随着时间的增加净化率下降;在热脱附滑动弧放电等离子体净化过程中,甲苯降解效率最高为97.3%。将滑动弧放电等离子体反应器出口气相产物收集进行FT-IR检测,发现放电后有CO2、CO、H2O和NO2产生,并分析了甲苯的降解机理。     

国内电炉钢发展现状与应用前景

通过电炉铜与转炉铜能耗对比,突显了电炉钢的节能与环保优势,同时介绍了国内外电炉钢应用现状。随着社会工业化的发展所带来的钢铁积蓄量的增加,以及电炉钢技术的不断完善和发展,加之迎合国家低碳经济政策的实施,国内电炉钢发展具有广阔前景。     

等离子工艺与H_2O_2联合处理酸性橙Ⅱ溶液的研究

对气液两相滑动弧等离子与H2O2联合处理酸性橙Ⅱ溶液进行了研究。结果表明:两者具有明显的协同效应,可减少等离子放电时间,提高了降解效率。质量浓度为300 mg/L的酸性橙Ⅱ溶液,加入体积分数为0.48～0.96 mL/L的H2 O2(30%),循环降解2次的脱色率在92%以上。当加入过氧化氢的体积分数是1.92 mL/L时,循环降解1次脱色率为93.32%。而且降解后的溶液随着放置时间的延长,脱色率进一步降低;且放置8 h时,降解率下降最明显。     

Gliding arc plasma processing for decomposition of chloroform

The decomposition of chloroform (CHCl₃) diluted in air was studied. The experiment was carried out by using a gliding arc plasma. Different values of initial concentrations of chloroform, total gas flow rates, and input power frequencies have been used to investigate this effects on the conversion reaction products both qualitatively and quantitatively. Experimental results indicate that the maximum conversion of chloroform was 97% at a total gas flow rate of 180?L?h^?1 containing 1% chloroform. Using air as carrier gas, decomposition of CHCl₃ produces CCl₄, CO₂, CO, and Cl₂ as the main products. Small amounts of HCl and COCl₂ are also detected. Liquid products were also produced.