Wayfinding with a GPS-based mobile navigation system: A comparison with maps and direct experience

This study examined the effectiveness of a Global Positioning System (GPS)-based mobile navigation system in comparison to paper maps and direct experience of routes, by focusing on the user's wayfinding behavior and acquired spatial knowledge. Based on information received from one of these three media, participants walked six routes finding the way to goals. Results showed that GPS users traveled longer distances and made more stops during the walk than map users and direct-experience participants. Also, GPS users traveled more slowly, made larger direction errors, drew sketch maps with poorer topological accuracy, and rated wayfinding tasks as more difficult than direct-experience participants. Characteristics of navigation with these three learning media and possible reasons for the ineffectiveness of the GPS-based navigation system are discussed.     

Supercritical water gasification of sewage sludge using bench-scale batch reactor: advantages and drawbacks

Sewage sludge, a byproduct of municipal wastewater treatment, was gasified by supercritical water using a bench-scale batch reactor. Configuration of bench-scale batch reactor and operation procedures are discussed in detail. Experience and challenges that arose during the experiment are also shared. Using the bench-scale reactor under the condition of 600 °C, 23 MPa, and a reaction time of 60 min without catalyst presence, a total gas yield of 9.8 mol/(kg-sewage sludge) was obtained. Furthermore, investigations on operational parameters were conducted. Extension of reaction time up to 60 min increased the gasification, reaching a plateau thereafter. Investigation on pressure indicated the superiority of supercritical pressure. The addition of Ni as a catalyst also promoted gasification, although inorganic salts and char seemed to cover the catalyst surface. With regard to the prospect of future operation at a municipal waste water treatment plant, the effect of operational parameters on heavy metal concentration in the liquid phase is also discussed.     

Nylon recovery from carpet waste through pyrolysis under the presence of zinc oxide and the roll-milling treatment

Recycling of carpet waste is not extensively carried out because of its complex combination of materials. A representative type of carpet consists of three layers: nylon fibers, adhesives, and backing materials made of poly(vinyl chloride), PVC. Thermal treatment of carpet waste, thus, leads to the emission of hazardous chlorinated compounds. In the present work, we have employed the one-directional thermal treatment of the backing materials under the presence of zinc oxide, which promotes the thermal degradation of PVC. Nylon fibers could be effectively recovered by the consequent milling treatment from the brittle backing materials. The influence of process parameters, such as pyrolysis temperature and reaction time, on the separation efficiency is discussed.     

Quantitative analysis of microbial biomass yield in aerobic bioreactor

We have studied the integrated model of reaction rate equations with thermal energy balance in aerobic bioreactor for food waste decomposition and showed that the integrated model has the capability both of monitoring microbial activity in real time and of analyzing biodegradation kinetics and thermal-hydrodynamic properties. On the other hand, concerning microbial metabolism, it was known that balancing catabolic reactions with anabolic reactions in terms of energy and electron flow provides stoichiometric metabolic reactions and enables the estimation of microbial biomass yield (stoichiometric reaction model). We have studied a method for estimating real-time microbial biomass yield in the bioreactor during food waste decomposition by combining the integrated model with the stoichiometric reaction model. As a result, it was found that the time course of microbial biomass yield in the bioreactor during decomposition can be evaluated using the operational data of the bioreactor (weight of input food waste and bed temperature) by the combined model. The combined model can be applied to manage a food waste decomposition not only for controlling system operation to keep microbial activity stable, but also for producing value–added products such as compost on optimum condition.     

Preparation and performance of arsenate (V) adsorbents derived from concrete wastes

Solid adsorbent materials, prepared from waste cement powder and concrete sludge were assessed for removal of arsenic in the form of arsenic (As(V)) from water. All the materials exhibited arsenic removal capacity when added to distilled water containing 10–700 mg/L arsenic. The arsenic removal isotherms were expressed by the Langmuir type equations, and the highest removal capacity was observed for the adsorbent prepared from concrete sludge with heat treatment at 105 °C, the maximum removal capacity being 175 mg-As(V)/g. Based on changes in arsenic and calcium ion concentrations, and solution pH, the removal mechanism for arsenic was considered to involve the precipitation of calcium arsenate, Ca₃(AsO₄)₂. The enhanced removal of arsenic for the adsorbent prepared from concrete sludge with heat treatment was thought to reflect ion exchange by ettringite. The prepared adsorbents, derived from waste cement and concrete using simple procedures, may offer a cost effective approach for arsenic removal and clean-up of contaminated waters, especially in developing countries.     

Initial design process of the sustainability science ontology for knowledge-sharing to support co-deliberation

Implementation of the sustainability science (SS) approach is often difficult because of poor communication between experts from different academic fields. We focused on ontology engineering as a method of knowledge structuring that supports the co-deliberation process. However, SS is too broad for a few experts to construct an ontology because SS targets and covers almost all existing research fields from the viewpoint of problem-solving. The N-iteration process is required for completing an SS ontology. In the present paper, we discuss the initial design process for constructing an ontology on SS from the aspect of a knowledge-sharing tool to support co-deliberation. First, we identified the SS ontology by referring to the existing literature. Second, we traced the structuring process of the SS ontology, which is independent of the existing research domain. Third, we compared the SS ontology with existing ontologies or concept structures on SS. Fourth, we assessed the SS ontology produced in the initial process in terms of relevance and coverage and addressed areas for improvement in order to facilitate co-deliberation among researchers from different domains. As a result of developing the SS ontology and applying it to the mapping tool that we developed based on the ontology, we found the following three points: the SS ontology enables us to define concepts relevant to SS without overlapping by distinguishing part-of and attribute-of relationships at the upper level of the ontology; the SS-based mapping tool successfully represents the potential countermeasures required by the targeted problem for all scientific fields except experimental engineering; however, the SS ontology requires further improvement in order to represent the conceptual linkage arising from compound and secondary problems and the fulfillment of classes at the lower hierarchy of Shortage problem, and requires slots for the entire hierarchy. In addition, based on the discussion of the areas for improvement, we found that missing slots and classes should be added in the process in which we use or improve tools corresponding to a variety of requirements for supporting co-deliberation. In this way, we are able to propose an incremental process for constructing the SS ontology from the aspect of a knowledge-sharing tool to support co-deliberation.     

Influence of arsenic stress on synthesis and localization of low-molecular-weight thiols in Pteris vittata

The roles of low-molecular-weight thiols (LMWTs), such as glutathione and phytochelatins, in arsenic (As) tolerance and hyperaccumulation in Pteris vittata an As-hyperaccumulator fern remain to be better understood. This study aimed to thoroughly characterize LMWT synthesis in P. vittata to understand the roles played by LMWTs in As tolerance and hyperaccumulation. LMWT synthesis in P. vittata was induced directly by As, and not by As-mediated oxidative stress. Expression of PvECS2, one of the putative genes of γ-glutamylcysteine synthetase (γECS), increases in P. vittata shoots at 48 h after the onset of As exposure, almost corresponding to the increase in the concentrations of γ-glutamylcysteine and glutathione. Furthermore, localization of As showed similar trends to those of LMWTs in fronds at both whole-frond and cellular levels. This study thus indicates the specific contribution of LMWTs to As tolerance in P. vittata. γECS may be responsible for the As-induced enhancement of LMWT synthesis.