Photodegradation of gaseous acetaldehyde and methylene blue in aqueous solution with titanium dioxide-loaded activated carbon fiber polymer materials and aquatic plant ecotoxicity tests

TiO₂-supported activated carbon felts (TiO₂–ACFTs) were prepared by dip coating of felts composed of activated carbon fibers (ACFs) with either polyester fibers (PS-A20) and/or a polyethylene pulp (PE-W15) in a TiO₂ aqueous suspension followed by calcination at 250 °C for 1 h. The as-prepared TiO₂–ACFTs with 29–35 wt.% TiO₂ were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and N₂ adsorption. The TiO₂–ACFT(PS-A20) samples with 0 and 29 wt.% TiO₂ were microporous with specific surface areas (S _BET) of 996 and 738 m²/g, respectively, whereas the TiO₂–ACFT(PE-W15) samples with 0 and 35 wt.% TiO₂ were mesoporous with S _BET of 826 and 586 m²/g, respectively. Adsorption and photocatalytic activity of the as-prepared samples were evaluated by measuring adsorption in the dark and photodegradation of gaseous acetaldehyde (AcH) and methylene blue (MB) in aqueous solution under UV light. The TiO₂ loading caused a considerable decrease in the S _BET and MB adsorption capacity along with an increase in MB photodegradation and AcH mineralization. Lemna minor was chosen as a representative aquatic plant for ecotoxicity tests measuring detoxification of water obtained from the MB photodegradation reaction with the TiO₂–ACFT samples under UV light.     

Speciation of the radioactive nuclides in incinerator fly ash of municipal solid waste using sequential extractions

Journal of Material Cycles and Waste Management - The radioactive nuclides in the incinerator fly ashes from municipal solid waste sampled in June 2006 were analyzed with γ-ray spectrometry....     

Preparation and performance of arsenate (V) adsorbents derived from concrete wastes

Solid adsorbent materials, prepared from waste cement powder and concrete sludge were assessed for removal of arsenic in the form of arsenic (As(V)) from water. All the materials exhibited arsenic removal capacity when added to distilled water containing 10–700 mg/L arsenic. The arsenic removal isotherms were expressed by the Langmuir type equations, and the highest removal capacity was observed for the adsorbent prepared from concrete sludge with heat treatment at 105 °C, the maximum removal capacity being 175 mg-As(V)/g. Based on changes in arsenic and calcium ion concentrations, and solution pH, the removal mechanism for arsenic was considered to involve the precipitation of calcium arsenate, Ca₃(AsO₄)₂. The enhanced removal of arsenic for the adsorbent prepared from concrete sludge with heat treatment was thought to reflect ion exchange by ettringite. The prepared adsorbents, derived from waste cement and concrete using simple procedures, may offer a cost effective approach for arsenic removal and clean-up of contaminated waters, especially in developing countries.     

Quantitative analysis of microbial biomass yield in aerobic bioreactor

We have studied the integrated model of reaction rate equations with thermal energy balance in aerobic bioreactor for food waste decomposition and showed that the integrated model has the capability both of monitoring microbial activity in real time and of analyzing biodegradation kinetics and thermal-hydrodynamic properties. On the other hand, concerning microbial metabolism, it was known that balancing catabolic reactions with anabolic reactions in terms of energy and electron flow provides stoichiometric metabolic reactions and enables the estimation of microbial biomass yield (stoichiometric reaction model). We have studied a method for estimating real-time microbial biomass yield in the bioreactor during food waste decomposition by combining the integrated model with the stoichiometric reaction model. As a result, it was found that the time course of microbial biomass yield in the bioreactor during decomposition can be evaluated using the operational data of the bioreactor (weight of input food waste and bed temperature) by the combined model. The combined model can be applied to manage a food waste decomposition not only for controlling system operation to keep microbial activity stable, but also for producing value–added products such as compost on optimum condition.     

Comparison of Different Packing Materials for the Biofiltration of Air Toxics

Abstract

Four different biofilter packing materials (two porous ceramics, perlite, and open pore polyurethane foam) were compared for the removal of toluene vapors. The focus was on evaluating performance at relatively short gas retention time (13.5 and 27 sec). The reactors were initially operated as biotrickling filters with continuous feeding and trickling of a nutrient solution. After significant plugging of the biotrickling filter beds with biomass was observed, the operation mode was switched to biofiltration with only periodic supply of mineral nutrients. This resulted in stable conditions, which allowed detailed investigations over >6 months. The reactor packed with cattle bone Porcelite (CBP), a ceramic material containing some macronutrients and micronutrients, exhibited the highest performance. The critical load (i.e., load at which 95% removal occurred) was 29 g m^?3 hr^?1 at a gas retention time of 13.5 sec and 66 g m^?3 hr^?1 at a gas retention time of 27 sec. After the long-term experiment, the packing materials were taken from the reactors and examined. The reactors were divided into three sections, top, middle, and bottom, to determine whether spatial differentiation of biomass occurred. The assays included a double-staining technique to count total and live microorganisms and determination of moisture, protein, and dry weight contents. Microbial community analysis was also conducted by denaturing gradient gel electrophoresis. The results showed that most reactors had a significant fraction of inactive biomass. Comparatively, the CBP biofilter held significantly higher densities of active biomass, which may be the reason for the higher toluene removal performance. The analyses suggest that favorable material properties and the nutrients slowly released by the CBP provided better environmental conditions for the process culture.     

Influence of arsenic stress on synthesis and localization of low-molecular-weight thiols in Pteris vittata

The roles of low-molecular-weight thiols (LMWTs), such as glutathione and phytochelatins, in arsenic (As) tolerance and hyperaccumulation in Pteris vittata an As-hyperaccumulator fern remain to be better understood. This study aimed to thoroughly characterize LMWT synthesis in P. vittata to understand the roles played by LMWTs in As tolerance and hyperaccumulation. LMWT synthesis in P. vittata was induced directly by As, and not by As-mediated oxidative stress. Expression of PvECS2, one of the putative genes of γ-glutamylcysteine synthetase (γECS), increases in P. vittata shoots at 48 h after the onset of As exposure, almost corresponding to the increase in the concentrations of γ-glutamylcysteine and glutathione. Furthermore, localization of As showed similar trends to those of LMWTs in fronds at both whole-frond and cellular levels. This study thus indicates the specific contribution of LMWTs to As tolerance in P. vittata. γECS may be responsible for the As-induced enhancement of LMWT synthesis.     

Direct determination of neonicotinoid insecticides in an analytically challenging crop such as Chinese chives using selective ELISAs

ABSTRACT

Easy-to-use commercial kit-based enzyme-linked immunosorbent assays (ELISAs) have been used to detect neonicotinoid dinotefuran, clothianidin and imidacloprid in Chinese chives, which are considered a troublesome matrix for chromatographic techniques. Based on their high water solubility, water was used as an extractant. Matrix interference could be avoided substantially just diluting sample extracts. Average recoveries of insecticides from spiked samples were 85–113%, with relative standard deviation of <15%. The concentrations of insecticides detected from the spiked samples with the proposed ELISA methods correlated well with those by the reference high-performance liquid chromatography (HPLC) method. The residues analyzed by the ELISA methods were consistently 1.24 times that found by the HPLC method, attributable to loss of analyte during sample clean-up for HPLC analyses. It was revealed that the ELISA methods can be applied easily to pesticide residue analysis in troublesome matrix such as Chinese chives.     

Biohydrogen using leachate from an industrial waste landfill as inoculum

Since hydrogen is a renewable energy source, biohydrogen has been researched in recent years. However, data on hydrogen fermentation by a leachate from a waste landfill as inoculum are scarce. We investigated hydrogen production using a leachate from an industrial waste landfill in Kanagawa Prefecture. The results showed no methane gas production, and the leachate was a suitable inoculum for hydrogen fermentation. The maximum H₂ yield was 2.67 mol of H₂ per mol of carbohydrate added, obtained at 30°C and an initial pH of 7. The acetate and butyrate production was significant when the H₂ yield was higher. Oxidation–reduction potential analysis of the culture suggested that hydrogen-producing bacteria in the leachate were facultative anaerobic. Scanning electron microscope observations revealed that the hydrogen-producing bacteria comprised bacilli about 2 μm in length.