Green energy generation by pressure retarded osmosis: State of the art and technical advancement—review

Pressure-retarded osmosis (PRO) is a method for converting salinity gradients to power by allowing water to flow through a semi-permeable membrane against an applied hydraulic pressure. PRO already has a long history, starting from the middle of the last century, and has rapidly improved in recent years. In this paper, we present a historical development of PRO since its inception: the development of this renewable energy process has gone through several stages, depending on technological developments, worldwide energy demands, and environmental concerns. The technological progress of the process is also studied, as well as its cost viability and environmental impact. Finally, some ideas to further develop the PRO process and mitigate its detrimental effects are discussed.     

Evaluation of Tire-Derived Fuel for Use in Nitrogen Oxide Reduction by Reburning

ABSTRACT

Tire-derived fuel (TDF) was tested in a small-scale (44 kW or 150,000 Btu/hr) combustor to determine its feasibility as a fuel for use in reburning for control of nitrogen oxide (NO). TDF was gravity-fed into upward flowing combustion gases from a primary natural gas flame doped with ammonia to simulate a high NO combustion process. Emissions of NO, oxygen, carbon dioxide, carbon monoxide, and particulate matter were measured. The tests varied the nominal primary NO level from 600 to 1,200 ppm and the primary stoichiometry from 1.1 to 1.2, and used both natural gas and TDF as reburn fuels. The reburn injection rate was varied to achieve 8–20% of the total heat input from the reburn fuel. NO emissions reductions ranged between 20 and 63% when using TDF, depending upon the rate of TDF injection, primary NO, and primary stoichiometry. NO emission reductions when using natural gas as the reburn fuel were consistently higher than those when using TDF. While additional work remains to optimize the process and evaluate costs, TDF has been shown to have the potential to be a technically viable reburning fuel.     

Low‐concentration hydrogen peroxide decontamination for Bacillus spore contamination in buildings

Remediation and recovery efforts after a release of Bacillus anthracis (anthrax) spores may be difficult and costly. In addition, response and recovery technologies may be focused on critical resources, leaving the small business or homeowner without remediation options. This study evaluates the efficacy of relatively low levels of hydrogen peroxide vapor (HPV) delivered from off‐the‐shelf equipment for the inactivation of Bacillus spores within an indoor environment. Decontamination evaluations were conducted in a house using both Bacillus atrophaeus var. globigii (Bg; as surrogates for B. anthracis) inoculated on the carpet and galvanized metal as coupons and Geobacillus stearothermophilus (Gs) as biological indicators on steel. The total decontamination time ranged from 4 to 7 days. Using the longer exposure times, low concentrations of HPV (average levels below 20 parts per million) effectively inactivated Bg and Gs spores on the materials tested. The HPV was generated with commercial humidifiers and household‐strength hydrogen peroxide solutions. The presence of home furnishings did not have a significant impact on HPV efficacy. This simple, inexpensive, and effective decontamination method could have significant utility for remediation following a B. anthracis spore release, such as following a terrorist attack.     

Study of the effects of drinking water treatment sludge on the properties of Class F fly ash-based geopolymer

Environmental Science and Pollution Research - Drinking water treatment sludge (DWTS) generated from water treatment plants is a global issue because of the environmental risks it imposes. Managing...     

Bathymetric variation of epiphytic assemblages on Posidonia oceanica (L.) Delile leaves in relation to anthropogenic disturbance in the southeastern Mediterranean

A survey of the epiphytic leaves of Posidonia oceanica was conducted along a depth transect at both the control station Attaya in the Kerkennah Islands and the disturbed Mahres station on the Sfax coast (Tunisia). Samples were collected by scuba divers at depths of 5, 10, 15, and 20 m in July 2008. We evaluated whether the pattern of spatial variability of the macroepiphyte assemblages of leaves of Posidonia oceanica differed in relation to anthropogenic interference. The results indicate that the decrease in shoot density and leaf length according to depth was low at Mahres. The biomass of epiphytic leaves and the percentage cover of epiphytic assemblages decreased with depth for both stations and heavily at Mahres, this decline being related to anthropogenic disturbance. This study shows that the highest values of epifauna and epiflora were detected at the disturbed station Mahres. Macroalgae assemblages decreased with depth at both stations and were dominated by Rhodophyta, whereas the percentage cover of the epifauna leaf that decreases according to depth was dominated by Hydrozoa and Bryozoa. Changes in epiphyte assemblages, epiphytic biomass, percentage cover, and species richness in proportion to Heterokontophyta, Rhodophyta, Cyanobacteria, Hydrozoa, Porifera, and Tunicata between the two stations constitute promising tools for detecting environmental disturbance.     

Sequential extraction of Cs and Sr from Ain Oussera soils around Es-Salam research reactor facility

Four types of undisturbed soil in Ain Oussera region around the Es-Salam reactor facility, located in the south of Algiers, Algeria, at about 200 km, were artificially contaminated for one year with stable CsCl and SrCl₂ in order to simulate an accidental release of these elements. This study was performed using sequential extraction procedure based on Shultz method and containing six fractions. The selectivity of the extraction protocol was confirmed by analyzing some elements (Ca, C, Fe, Mn, Si and Al) designed as indicators of the targeted phases. The obtained results showed an acceptable reproducibility, in view of the coefficients of variation that were in most cases less than 15%. The results revealed a clear proportional correlation between the extracted Cs and Sr in fractions for each soil and some of soils physicochemical properties. Organic matter appears to play an important role in the soil retention, particularly for Cs where the extracted percentage exceeds to 30% in whole soils. In contrast, strontium expresses a remarkable affinity for the fraction bound to carbonates. The obtained data also indicate that the availability of Cs in the four soils is less important compared to Sr availability. This is illustrated by the higher value of extracted Sr in the easily extractible phase, including the water-soluble and the exchangeable fraction.     

Emission factors for PCDD/PCDF and dl-PCB from open burning of biomass

The Stockholm Convention on Persistent Organic Pollutants includes in its aims the minimisation of unintentional releases of polychlorinated dibenzo-dioxins and dibenzofurans (PCDD/PCDF) and dioxin like PCB (dl-PCB) to the environment. Development and implementation of policies to achieve this aim require accurate national inventories of releases of PCDD/PCDF/dl-PCB. To support this objective, the Conference of Parties established a process to review and update the UNEP Standardized Toolkit for Identification and Quantification of Dioxin and Furan Releases. An assessment of all emission inventories was that for many countries open burning of biomass and waste was identified as the major source of PCDD/PCDF releases. However, the experimental data underpinning the release estimates used were limited in number and, consequently, confidence in the accuracy of the emissions predictions was low. There has been significant progress in measurement technology since the last edition of the Toolkit in 2005. In this paper we reassess published emission factors for release of PCDD/PCDF and dl-PCB to land and air.In total, four types of biomass and 111 emission factors were assessed. It was found that there are no systematic differences in emission factors apparent between biomass types or fire classes. The data set is best described by a lognormal distribution. The geometric mean emission factors (EFs) for releases of PCDD/PCDF to air for the four biomass classes used in the Toolkit (sugarcane, cereal crops, forest and savannah/grass) are 1.6 μg TEQ (t fuel)⁻¹, 0.49 μg TEQ (t fuel)⁻¹, 1.0 μg TEQ (t fuel)⁻¹ and 0.4 μg TEQ (t fuel)⁻¹, respectively. Corresponding EFs for release of PCDD/PCDF to land are 3.0 ng TEQ (kg ash)⁻¹, 1.1 ng TEQ (kg ash)⁻¹, 1.1 ng TEQ (kg ash)⁻¹ and 0.67 ng TEQ (kg ash)⁻¹. There are now also sufficient published data available to evaluate EFs for dl-PCB release to air for sugarcane, forest and grass/savannah; these are 0.03 μg TEQ (t fuel)⁻¹, 0.09 μg TEQ (t fuel)⁻¹ and 0.01 μg TEQ (t fuel)⁻¹, respectively. The average EF for dl-PCB release to land is 0.19 ng TEQ (kg ash)⁻¹. Application of these EFs to national emissions of PCDD/PCDF for global estimates from open burning will lower previous estimates of PCDD/PCDF releases to air and to land by 85% and 90%, respectively. For some countries, the ranking of their major sources will be changed and open burning of biomass will become less significant than previously concluded.     

Scenario‐Based Evaluation of Commercially Available Cleaning Robots for Collection of Bacillus Spores from Environmental Surfaces

The cleaning robots, a vacuum‐based robot (R2) and a wetted‐wipe‐based robot (R4), were evaluated in this study to determine their effectiveness for sampling Bacillus atrophaeus spores. The tests were designed to evaluate the benefit of robot sampling on large areas with two different contamination scenarios: a high‐concentration, low spatial extent contamination (hot spot) and a low concentration, high spatial extent contamination (widely dispersed). The hot spot tests were conducted with the high spore contamination (approximately 10⁷ colony forming units [CFUs]) on a limited area (30.5 cm × 30.5 cm), 2 percent of the entire test. The widely dispersed tests were conducted with approximately 0.1 CFUs/cm² for floor laminate and approximately 10 CFUs/cm² for carpet surfaces. The widely dispersed tests distributed spores across the test surface and covered approximately 40 percent of the entire test area. The test results showed that both robots successfully sampled a large quantity of spores from carpet and floor laminate surfaces for both test scenarios. Robot performance is discussed in the context of currently used surface sampling methods. © 2014 Wiley Periodicals, Inc.*     

Quality control for sampling of PCDD/PCDF emissions from open combustion sources

Both long duration (>6 h) and high temperature (up to 139 °C) sampling efforts were conducted using ambient air sampling methods to determine if either high volume throughput or higher than ambient air sampling temperatures resulted in loss of target polychlorinated dibenzodioxins/dibenzofurans (PCDDs/PCDFs) from a polyurethane foam (PUF) sorbent. Emissions from open burning of simulated military forward operating base waste were sampled using EPA Method TO-9A for 185 min duration using a filter/PUF/PUF in series combination. After a 54 m³ sample was collected, the sampler was removed from the combustion source and the second PUF was replaced with a fresh, clean PUF. An additional 6 h of ambient air sampling (171 m³) was conducted and the second PUF was analyzed to determine if the PCDD/PCDF transferred from the filter and the first PUF. Less than 4.4% of the initial PCDD/PCDF was lost to the second PUF. To assess the potential for blow off of PCDD/PCDF analytes during open air sampling, the mobility of spiked mono- to hepta-PCDD/PCDF standards across a PUF sorbent was evaluated from ambient air temperatures to 145 °C with total volumes between 600 L and 2400 L. Lower molecular weight compounds and higher flow amounts increased release of the spiked standards consistent with vapor pressure values. At 600 L total sampled volume, the release temperature for 1% of the tetra-CDD (the lowest chlorinated homologue with a toxic compound) was 87 °C; increasing the volume fourfold reduced this temperature to 73 °C.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.