Deployment of parabolic trough concentrated solar power plants in North Africa – a case study for Libya

The study addresses the potential of using concentrated solar power plants (CSPs) as a sustainable alternative of clean energy generation in the Mediterranean region and, in particular, in its North Africa shore. This location presents attractive conditions for the installation of CSPs, in particular high solar irradiation, good manpower concentration, and proximity and availability of water resources for condenser cooling. Energetic, exergetic, and economic analyses were conducted taking into consideration a particular type of CSPs - the parabolic trough concentrated solar power plant, which incorporates the most proven technology and it is already used in Southern Europe (Spain). In addition, the study considered the impact of project financing and incentives on the cost of energy. The combination of higher values for performance and potentially lower levelized cost of electricity (LCE) for the North Africa Mediterranean Rim than the South of Spain region can yield a very favorable return for the invested capital. Tripoli compared to Almeria presented superior performance and potentially lower LCE values ($0.18/kWh versus $0.22/kWh). This is significant, even when it is taken into consideration the fact that the plant in Tripoli, despite a relatively modest capacity factor of 34%, has a large gross power output of 173,886 MWhe. In addition, the implementation at the Tripoli location of a plant similar to the Anadsol plant has a slight advantage (2–3%) in terms of overall efficiency.     

Contamination of soil and the medicinal plant <Emphasis Type="Italic">Phyllanthus niruri</Emphasis> Linn. with cadmium in ceramic industrial areas

Phyllanthus niruri is a plant that is used to prevent calcium oxalate crystallisation and to block the stone formation in urolithiasis. Contaminants in the environment can be readily taken up by medicinal plants due to their ability to absorb chemicals into their tissues. If contaminated plants are ingested, they have the potential to negatively affect human and environmental health. The aim of this study was to assess contamination in the soil and the medicinal plant P. niruri by cadmium (Cd) in ceramic industrial areas of Monte Carmelo, Brazil. Soil samples and plant samples (divided in root, shoot and leaves) were collected from a contaminated monitoring site and from a rural area (which was used as a reference site for comparative purposes). The Cd concentrations of the samples were analysed with an atomic absorption spectrometer. P. niruri was found to be sensitive to soil contamination by Cd that was attributed to ceramic industrial emissions. The results revealed that Cd bioaccumulation in the roots and shoots of P. niruri was associated with a significant increase (p?<?0.05) in the concentration of active lignan compounds (phyllanthin and hypophyllanthin) in the leaves. The identification of high concentrations of Cd and active lignan compounds suggests a risk of contamination of the site and the risk of a high dose of Cd to people exposed at the site.     

Review: recent advances in biogas purifying technologies

Biomethane production through biogas upgrading is a promising renewable energy for some industries which could be part of the equilibrium needed with fossil fuels consumption to achieve a sustainable society. This paper presents a comprehensive list of biogas upgrading technologies focused on carbon dioxide removal as well as recent advances reported by researcher with wide expertise in this topic. Additionally, an extensive costs–performance comparison among the technologies studied is discussed. Among the different alternatives, chemical scrubbing stood out to achieve high biomethane purities while cryogenic technologies proved to be effective against methane losses. Regarding the different costs, water scrubbing and membrane separation seem to be the most affordable techniques.     

Field scale characterization and modeling of contaminant release from a coal tar source zone

A coal tar contaminated site was characterized using traditional and innovative investigation methods. A careful interpretation of hydrogeological and hydrogeochemical data allowed for the conceptualization of the heterogeneous coal tar distribution in the subsurface. Past and future contaminant release from the source zone was calculated using a modeling framework consisting of a three-dimensional steady-state groundwater flow model (MODFLOW) and two hydrogeochemical models (MIN3P). Computational time of long-term simulations was reduced by simplifying the coal tar composition using 3 composite and 2 individual constituents and sequential application of a 2D centerline model (for calibration and predictions) and a 3D model (only for predictions). Predictions were carried out for a period of 1000 years. The results reveal that contaminant mass flux is governed by the geometry of zones containing residual coal tar, amount of coal tar, its composition and the physicochemical properties of the constituents. The long-term predictions made using the 2D model show that even after 1000 years, source depletion will be small with respect to phenanthrene, 89% of initial mass will be still available, and for the moderately and sparingly soluble composite constituents, 60% and 98%, respectively.     

Highly active photocatalytic coatings prepared by a low-temperature method

Photocatalytic properties of titanium (IV) oxide (TiO₂) in anatase form can be used for various purposes, including photocatalytic purification of water. For such an application, suspended or fixed photocatalytic reactors are used. Those with fixed phase seem to be preferred due to some advantages, one of which is the avoidance of photocatalyst filtration. To avoid leaching and exfoliation of the fixed phase, an immobilization procedure leading to a good adhesion of a catalyst to a substrate is crucial. Within this work, we present physical and photocatalytic characterization results of five commercially available TiO₂ photocatalysts (P25, P90, PC500, KRONOClean 7000, VPC-10) and one pigment (Hombitan LO-CR-S-M), which were successfully immobilized on glass slides by a “sol suspension” procedure. Different mechanical tests and characterization methods were used to evaluate the stability and morphology of the layers. Evaluation of photocatalytic activity was done by tests under UVA and UV–vis irradiation, using a method based on the detection of the fluorescent oxidation product of terephthalic acid (TPA), i.e., hydroxyterephthalic acid (HTPA). Aeroxide® P90 incorporated into the silica-titania binder was the most photocatalytically active layer and, unlike the others, showed significant increase of photocatalytic activity through the entire range of tested UVA irradiation intensities (2.3 mW/cm²–6.1 mW/cm²). The high mechanical stability of some photocatalytic layers allows using them in water photocatalytic purification reactions.     

Green energy generation by pressure retarded osmosis: State of the art and technical advancement—review

Pressure-retarded osmosis (PRO) is a method for converting salinity gradients to power by allowing water to flow through a semi-permeable membrane against an applied hydraulic pressure. PRO already has a long history, starting from the middle of the last century, and has rapidly improved in recent years. In this paper, we present a historical development of PRO since its inception: the development of this renewable energy process has gone through several stages, depending on technological developments, worldwide energy demands, and environmental concerns. The technological progress of the process is also studied, as well as its cost viability and environmental impact. Finally, some ideas to further develop the PRO process and mitigate its detrimental effects are discussed.     

Foraminiferal biotopes and their distribution control in Ria de Aveiro (Portugal): a multiproxy approach

Ria de Aveiro, which is located in the centre of Portugal (40° 38′ N, 8° 45′ W), is a well-mixed and complex coastal lagoon that is separated from the sea by a sandy barrier and connects with the Atlantic through an artificial inlet. Tidal currents are the main factor controlling the lagoon’s hydrodynamics and, to a great extent, the sedimentary dynamic. The inner lagoonal zones receive input from several rivers and experience the pressure caused by the accumulation of organic matter and pollutants (namely, trace metals) from diverse anthropic activities. This paper is the first piece of work aiming to recognize, characterize and explain the main benthic foraminiferal biotopes in Ria de Aveiro. To provide a broad overview of this kind of setting, our results are compared to those of previous published studies conducted in similar transitional environments. The research is based on an investigation of 225 sites spread throughout this ecosystem. Utilizing a statistical approach, this study analyses the details of dead benthic foraminiferal assemblages composed of 260 taxa, the texture and composition (mineralogical and geochemical) of the sediment and physicochemical data. On the basis of the results of R-mode and Q-mode cluster analyses, several different biotopes can be defined as marsh biotope/near-marsh biotope; marginal urban/marginal urban mixing biotope; inner-outer lagoon biotope or enclosed lagoon; outer lagoon biotope, mixed sub-biotope; and outer lagoon, marine sub-biotope. These biotopes are related to foraminifera assemblages and substrate type and are influenced by local currents, water depth, chemical and physicochemical conditions, river or oceanic proximity, and anthropogenic impact, as evidenced by the mapping of the six factor loadings of the principal component analysis conducted herein. Based on a similar methodology of analysis as that applied in previous studies in the Lagoon of Venice, comparable biotypes were identified in Lagoon of Aveiro.     

Mechanical and toxicological evaluation of concrete artifacts containing waste foundry sand

The creation of metal parts via casting uses molds that are generally made from sand and phenolic resin. The waste generated after the casting process is called waste foundry sand (WFS). Depending on the mold composition and the casting process, WFS can contain substances that prevent its direct emission to the environment. In Brazil, this waste is classified according to the Standard ABNT NBR 10004:2004 as a waste Class II (Non-Inert). The recycling of this waste is limited because its characteristics change significantly after use. Although the use (or reuse) of this byproduct in civil construction is a technically feasible alternative, its effects must be evaluated, especially from mechanical and environmental points of view. Thus, the objective of this study is to investigate the effect of the use of WFS in the manufacture of cement artifacts, such as masonry blocks for walls, structural masonry blocks, and paving blocks. Blocks containing different concentrations of WFS (up to 75% by weight) were produced and evaluated using compressive strength tests (35 MPa at 28 days) and toxicity tests on Daphnia magna, Allium cepa (onion root), and Eisenia foetida (earthworm). The results showed that there was not a considerable reduction in the compressive strength, with values of 35 ± 2 MPa at 28 days. The toxicity study with the material obtained from leaching did not significantly interfere with the development of D. magna and E. foetida, but the growth of the A. cepa species was reduced. The study showed that the use of this waste in the production of concrete blocks is feasible from both mechanical and environmental points of view.     

Treatment of a clinical analysis laboratory wastewater from a hospital by photo-Fenton process at four radiation settings and toxicity response

Environmental Science and Pollution Research - The photo-Fenton process was performed with four radiation settings to treat clinical analysis laboratory wastewater (CALWW) from a hospital, with the...     

Presence of Torque Teno Virus (TTV) in Tap Water in Public Schools from Southern Brazil

Torque teno virus (TTV) was surveyed in tap water collected in schools from three municipalities located in the south of Brazil. TTV genomes were found in 11.7 % (4/34) of the samples. TTV DNA was detected in 10.5 % (2/19) of the samples collected at the city of Caxias do Sul and in 25 % (2/8) of the samples from Pelotas. Those cities have a low rate of sewage treatment. All samples from Santa Cruz do Sul, which has nearly 92 % of its sewage treated, were negative. These results suggest that the amount of sewage treated may have an effect on the detection rates of TTV DNA in drinking water in a given urban area, showing a mild negative correlation (r = ?0.76), when comparing the percentage of sewage treatment to the detection of TTV genomes. The detection rate of TTV was also compared with Escherichia coli, showing a strong correlation (r = 0.97), indicating that TTV may be a suitable marker of fecal contamination.