花生壳、大豆壳和柚子皮对Cr3+、Cu2+和Ni2+的吸附研究

采用农林废弃物花生壳、大豆壳、柚子皮对重金属离子Cr3+、Cu2+和Ni2+进行吸附研究,探讨反应时间、吸附剂用量、pH、重金属离子初始浓度以及温度对吸附的影响.结果表明:柚子皮对Cr3+、Cu2+、Ni2+的吸附效果优于花生壳和大豆壳,其在20℃、pH 5.00、10.0 mg/kg条件下,反应360 min,Cr3+、Cu2+、Ni2+的吸附率分别可达83.20％、84.50％、59.10％;花生壳、大豆壳和柚子皮对Ni2+的吸附率远低于Cr3+和Cu2+；花生壳、大豆壳和柚子皮对Cr3+、Cu2+、Ni2+的吸附动力学可以用准二级动力学方程描述；吸附率随初始重金属离子浓度增加而降低,其吸附等温线可以用Langmuir方程描述；在一定范围内,吸附率随吸附剂用量增加而增加；溶液初始pH在2～5时,吸附率随pH增大而增加；Cu2、Ni2+的吸附量随温度的上升而逐渐减少,但Cr3+的吸附量随着温度的上升而略增加.     

膨润土对Pb2+、Cu2+、Cr3+的吸附动力学及等温线研究

研究所用膨润土的主要成分为SiO2和Al2O3,属于Ca基膨润土,BET表面积为50.83 m2/g.在恒温及恒定pH条件下,用静态吸附法研究了膨润土对Pb2 、Cu2 、Cr3 的吸附特性,结果表明其较好地符合Lagergten二级吸附速率方程,对这3种离子的吸附速率为Pb2 ＞Cu2 ＞Cr3 .利用3种等温线方程对吸附过程进行拟合,发现利用Langmuir吸附等温方程计算的值与膨润土吸附Pb2 、Cu2 、Cr3 试验数据最为吻合.膨润土对3种金属离子的平衡吸附量为Cr3 ＞Cu2 ＞Pb2 .     

皂化改性橘子皮生物吸附剂对重金属离子的吸附

以生物废料橘子皮(OP)为原料,经乙醇、氢氧化钠处理,得到改性橘子皮生物吸附剂SOP,将其用于对重金属离子Cu2+、Pb2+、Cd2+、Zn2+和Ni2+的吸附。研究了溶液pH、吸附时间和重金属离子初始浓度对SOP吸附性能的影响。结果表明,重金属离子在生物吸附剂上的吸附速率快,符合准二级动力学方程。SOP对重金属离子的吸附等温线符合Lang-muir模型,根据Langmuir模型计算SOP对Cu2+、Pb2+、Cd2+、Zn2+和Ni2+的饱和吸附量分别为56.82、152.4、66.27、33.90和23.02 mg/g,均高于改性前。常见阳离子的存在对重金属离子吸附的影响较小,改性后的橘子皮生物吸附剂可以再生重复使用4次以上,是性能良好的重金属离子吸附剂。     

橘子皮皂化交联改性及其对重金属离子的吸附

以生物废料橘子皮(OP)为原料,经乙醇、NaOH和CaCl2处理,得到皂化交联改性橘子皮(SCOP)生物吸附剂,将其用于对重金属离子Cu2+、pb2+、Cd2+、Zn2+和Ni2+的吸附,并研究了溶液pH、吸附时间和重金属离子初始浓度对SCOP吸附性能的影响.结果表明,重金属离子在改性橘子皮上的吸附速率快,符合准二级动力学方程；改性橘子皮对Cu2+、pb2+、Zn2+和Ni2+的吸附等温线符合Langmuir方程,对Cd2+的吸附等温线符合Freundlich方程,根据Langmuir方程计算对Cu2+、pb2+、Cd2+、Zn2+和Ni2+的饱和吸附量分别为72.73、209.80、85.84、56.18、33.80mg/g,均高于改性前.改性后的橘子皮生物吸附剂可以再生重复使用4次以上,是性能良好的重金属离子吸附剂.     

三乙二醇二甲基丙烯酸酯为交联剂制备的高吸水树脂对重金属的吸附

以前期工作中合成的树脂PAANa-TE为吸附剂进行重金属吸附测试,考察吸附剂用量、丙烯酸中和度、吸附时间、溶液pH、初始浓度和吸附温度对树脂吸附重金属离子Cu2+、Pb2+、Cr3+和Co2+性能的影响,用原子吸收分光光度计测定了树脂吸附Cu2+、Pb2+、Cr3+和Co2+后的残留浓度,树脂对4种金属离子的吸附容量分别为21.59、2.39、5.66和4.98 mmol/g,吸附容量大小为Cu2+Cr3+Co2+Pb2+,吸附速率顺序为Cr3+Pb2+Cu2+Co2+。结果表明,该树脂对高浓度重金属离子有较快速,高效率的吸附,吸附过程在100 min左右吸附容量达到最大,并用不同浓度的酸对吸附重金属离子的树脂进行脱附处理,脱附量很小,据此可考虑进一步对金属离子进行回收处理。且脱附率较低,因此,可对工业化和城市化进程所产生的各种化学形态的重金属水体污染物造成的生态环境和质量问题起到重要的改善作用。     

矸石基X型分子筛对水中Co2+、Cu2+、Cd2+和Cr3+的去除

以煤矸石为原料,采用碱熔后水热合成法制备X型分子筛并进行XRD、SEM、BET和Zeta电位分析。研究其对水中Co2+、Cu2+、Cd2+和Cr3+4种离子的吸附性能,包括吸附等温线、吸附动力学以及初始金属离子浓度、pH值对吸附性能的影响。所合成的矸石基X型分子筛的BET比表面积为676.02 m2/g,微孔孔容为0.263 cm3/g。吸附实验表明,矸石基X型分子筛能有效去除上述4种离子,同时实现煤矸石的资源化和金属离子的去除。4种离子的平衡吸附量均随初始浓度的增大而增大,相同条件下平衡吸附量的大小顺序为Cd2+>Cr3+>Cu2+>Co2+。准二级动力学模型能很好地描述4种离子的吸附动力行为。Langmuir模型对Co2+、Cu2+和Cd2+吸附的拟合较Freundlich模型高,说明其主要表现为物理吸附过程。4种离子的吸附速率均由液膜扩散和颗粒内扩散共同控制。     

核桃果皮炭粉对3种重金属离子吸附的影响

采用均匀设计的实验方法,研究了2种核桃果皮炭粉(提取水溶性混合物和未提取水溶性混合物的核桃皮炭粉)对Cr、Cu和Cd等重金属离子的吸附最优条件以及对3种离子吸附的影响因素。结果表明,核桃皮炭粉对Cr(Ⅵ)、Cd2+和Cu2+的吸附最优条件为:pH=4,温度为60℃,浓度为150μg/mL,吸附剂用量为2.4 g,时间为120 min;pH=4.5,温度为30℃,浓度为180μg/mL,吸附剂用量为5.4 g,时间为60 min;pH=5,温度为80℃,浓度为210μg/mL,吸附剂用量为0.4 g,时间为100 min;pH和Cr(Ⅵ)浓度增大,不利于2种吸附剂对Cr(Ⅵ)的吸附;pH和温度增大,不利于2种吸附剂对Cu2+的吸附;温度和吸附剂用量增加,有利于2种吸附剂对Cd2+的吸附。未提取水溶性混合物比提取水溶性混合物的核桃果皮炭粉对3种金属的吸附显著。2种吸附剂的吸附率均表现为Cr>Cd>Cu。     

改性花生壳对苯酚的吸附

以花生壳为原料,使用环氧氯丙烷、二甲胺及吡啶,以N,N-二甲基甲酰胺为反应介质改性花生壳。结果表明:改性花生壳对苯酚的去除效果优于未改性花生壳。在实验条件下,吸附剂的吸附量在溶液pH为9,吸附时间为120 min时达到最大;溶液离子强度对吸附的影响较大。分析了该反应体系的动力学和热力学参数,改性花生壳吸附苯酚过程拟用准二级动力学模型处理,计算得出平衡吸附量与实验值相符。改性花生壳对苯酚的吸附符合Langmuir和Freundlich等温模式,R2均大于0.98,Qmax在84.49～108.76 mg/g之间,Freundlich模式的吸附强度n值在1.211～1.262之间,热力学参数△G、△H、△S表明改性花生壳对苯酚的吸附过程是自发、吸热过程。     

改性甘蔗渣吸附废水中低浓度Cu2+的研究

利用离子液氯化-1-己基-3-甲基咪唑对甘蔗渣进行改性,利用改性甘蔗渣吸附去除模拟废水中低浓度的Cu2+,并对比了较优条件下甘蔗渣改性前后的Cu2+吸附性能.结果表明,溶液pH、改性甘蔗渣投加量、吸附时间对改性甘蔗渣吸附Cu2+均有一定的影响,较佳的溶液pH为5.41、改性甘蔗渣投加量为0.30 g、吸附时间为130 min;吸附温度升高Cu2+吸附率反而降低,因此选择在室温下进行吸附反应为宜;在以上较优条件下,改性甘蔗渣和甘蔗渣的Cu2+吸附率分别为83.20％和53.83％,前者的Cu2+吸附率提高了30.35％.     

改性花生壳对Cd(Ⅱ)和Pb(Ⅱ)的吸附机理

以前期制得改性块状花生壳为对象,测定改性花生壳等电点,考察离子强度对改性花生壳吸附Cd2+和Pb2+的影响、吸附前后吸附质溶液pH变化情况及蒸馏水、NaCl、HNO3、柠檬酸和EDTA 5种解吸液对Cd2+和Pb2+的解吸效果,并通过X-射线光电子能谱仪和傅里叶变换红外光谱仪对吸附前后的改性花生壳进行表征,推测并证实了改性花生壳对Cd2+和Pb2+可能的吸附机理。结果表明,改性花生壳对Cd2+和Pb2+可能的吸附机理是:Cd2+是通过外层络合、离子交换和内层络合的联合作用被吸附的;Pb2+主要是与改性花生壳上的O、N等活性基团发生内层络合;此外,改性花生壳表面生成的二氧化锰对Cd2+和Pb2+的吸附也起到一定的作用。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.