Use of Sphagnum peat moss and crushed mollusk shells in fixed-bed columns for the treatment of synthetic landfill leachate

A laboratory bench-scale fixed-bed column study operated as a down-flow configuration was conducted to evaluate Sphagnum peat moss and crushed mollusk shells as natural low-cost adsorbents for the removal of heavy metals from aerated and unaerated synthetic landfill leachate. Columns were packed with 15 cm of prepared peat moss, or 15 cm adsorbent mixtures made up of peat moss and crushed mollusk shells (4.0–4.75 mm) from Lake Ontario at different bed depth ratios. Peat was found to have the best adsorption capacities in columns treating aerated synthetic leachate for cadmium and nickel with 78.6% and 83.8% removal efficiencies, respectively. The removal of chemical oxygen demand (COD) and total nitrogen from the synthetic leachate was also monitored to evaluate the potential effects of biological activity on heavy metal adsorption. Columns receiving unaerated raw synthetic leachates did not show any significant removal of COD and total nitrogen, whereas some reduction in COD and total nitrogen was noted in the columns treating aerated synthetic landfill leachate. The results suggested that biological activity and biofilm growth could positively contribute to heavy metal retention within the fixed-media biosorption columns.     

Evaluation of the adsorption behavior of mixed perfluoroalkyl and polyfluoroalkyl substances onto granular activated carbon and styrene-divinylbenzene resins

Because of the remarkable chemical structure of perfluoroalkyl and polyfluoroalkyl substances (PFAS), as well as the complex conditions of water, selecting an appropriate adsorbent for treating PFAS is critical. Adsorption needs to be environmentally friendly, low cost, and consider the types of adsorbents that work well in mixed PFAS solutions. In the present study, we used mixed PFAS to estimate the PFAS activity. This research aimed to evaluate and compare the efficacy of the adsorption of PFAS from water using different adsorbents: granular activated carbon (GAC), IRA 910 (strong anion resin), and DOWEX MB-50 (mixed exchange resin). Batch adsorption isotherms and kinetic studies were performed for perfluorooctanoic acid (PFOA), perfluorooctane sulfonic acid (PFOS), and perfluorohexane sulfonic acid (PFHxS). Freundlich models consistently described the kinetic behavior with a high correlation coefficient (R² > 0.98). PFAS adsorption capacities on GAC and IRA910 were dependent on the chain length (PFOS > PFOA > PFHxS). The adsorption capacity of DOWEX MB-50 decreased because of the sulfonate effects (PFOS > PFHxS > PFOA). The rate constants (k₂) that represented the adsorption of PFAS on different adsorbents observed within 96 h were accurately determined by the pseudo-second-order (PSO) model. GAC achieved followed the relationship k₂(PFOS) > k₂(PFOA) > k₂(PFHxS). Furthermore, k₂ of IRA910 decreased in the order of k₂(PFOA) > k₂(PFOS) > k₂(PFHxS), implying that IRA910 promoted hydrophobicity more significantly on the adsorption of PFCAs than perfluoroalkane (-alkyl) sulfonic acids. The kinetics of DOWEX MB-50 revealed k₂(PFHxS) > k₂(PFOS) > k₂(PFOA) because gel-type resins like DOWEX MB-50 are more suitable for shorter-chain PFAS. Further investigation is needed to determine the effect of organic matter under natural conditions and evaluate adsorptive selection caused by operational complexities.     

Evaluation of a Soil‐Based System to Dissipate Multiple Pesticides

Pesticide contaminated wastewater resulting from leftover mixes, equipment cleaning, and container disposal are problems related to pesticide use. This study reports on the effectiveness of a soil‐based bioreactor (SBBR) to dissipate pesticides of differing concentrations and mixtures. In order to accomplish this study, soil columns were used to simulate the SBBR. A mixture of five herbicides and two insecticides from seven different chemical families (atrazine, dicamba, fluometuron, metolachlor, sulfentrazone, chlopyrifus, and λ‐cyhalothrin) were added to the SBBR‐simulated system as formulated products in three concentrations each: 0 part per million (control), 10 ppm, and 100 ppm. Additionally a 1,000 ppm treatment was added that included just the five herbicides to investigate how the system would respond to heavy loading. The system was run for 90 days with samples taken at day 4 (just prior to loading the columns), then at 30, 60, and 90 days. At low pesticide concentrations (10 and 100 ppm), there was significant dissipation (p < 0.05) of all pesticides in the columns except sulfentrazone. At 1,000 ppm, fluometuron, in addition to sulfentrazone, did not show significant dissipation. Overall, the system performed as expected and could be considered practical for use on farms or nurseries. ©2015 Wiley Periodicals, Inc.     

响应面法优化阴阳极同时作用电化学法处理染料废水

在自制电化学反应器中,以甲基橙模拟染料废水为处理对象,采用Box-Behnken Design响应面法研究了影响阴阳极同时作用电化学法处理染料废水的因素及其交互作用。实验得出各因素对废水脱色率影响的大小顺序为：电流密度> Fe³⁺浓度>Cl^-浓度。各因素之间的交互作用对废水脱色率影响的大小顺序为：电流密度和Fe³⁺浓度>电流密度和Cl^-浓度>Fe³⁺浓度和Cl^-浓度。优化结果表明：Fe³⁺浓度为1.02 mmol/L、Cl^-浓度为10.96 mmol/L、电流密度为11.52 mA/cm²时,最佳脱色率为94.67%。阴阳极同时作用电化学法对甲基橙去除效果显著。     

Adsorptive Separation of Lysozyme from Aqueous Solutions Using Sulphonyl and Carboxyl Functionalized Stearyl Alcohol Grafted Epichlorohydrin

In the present work ability of the two novel adsorbents, sulphonyl and carboxyl functionalized stearyl alcohol-grafted epichlorohydrin, SA-g-E-SO₃H, SA-g-E-COOH; to remove lysozyme (LYZ) from aqueous solution was assessed. The adsorbent characterization was done using FTIR, XRD, SEM and TGA analyses. The adsorption efficiency was influenced by solution pH and the optimum operating pH was found to be 4.0 for SA-g-E-SO₃H and 5.0 for SA-g-E-COOH and their adsorption efficiency was evaluated using the various isotherm and kinetics models. The Sips isotherm model and pseudo-second-order kinetic model were found to be the best for describing the equilibrium and kinetic behaviors of the adsorption process. Batch adsorption/desorption studies in acidic medium, for over six cycles showed excellent regeneration capability of the adsorbents and could lead to the development of viable and promising technology for the adsorptive recovery of LYZ from aqueous solutions. The efficiency of the adsorbents for the LYZ adsorption was verified using egg white. The result obtained from this study revealed that adsorption ability of 25 mg of SA-g-E-COOH is 98.4 % which is more than that of SA-g-E-SO₃H (96.2 %). The efficiency of SA-g-E-SO₃H to remove LYZ from aqueous solution was found to be higher compared to SA-g-E-COOH.     

Determining distribution coefficients for low cost adsorbents

As with other construction materials, coal fly ash contains trace metals that can leach into the natural environment. As part of a broader effort to encourage appropriate coal combustion product use in infrastructure applications (e.g., road construction, stabilization, and structural fill), this study evaluated traditional and low‐cost adsorbent alternatives for their capacity to attenuate trace metals. Batch sorption tests were used as a preliminary screen for a wide variety of low cost (e.g., steel byproducts, rubber dust, and compost) and innovative materials (e.g., kudzu, biofilm, and pond weed) as well as conventional materials (activated carbon, alumina, and zeolites). The removal rates were demonstrated in this study by observing the calculated distribution coefficient (K_d) which were determined using a program called MATLAB. Limestone and steel byproducts were found to be particularly effective with large K_d values of 15,740, 1,520, and 540 L kg^?1 for cadmium, chromium, and selenium and, for ladle refractory and mill scale, K_d values of 3,910, 670, and 1,760 L kg^?1 were observed. Among the three metals tested for this study, it was observed that most low cost and innovative materials removed cadmium quite efficiently; however, the removal of selenium and chromium depended on the substrate and prevailing pH. In general, these results suggest that alternative materials may have relevance in niche applications where leaching is a concern that can be addressed through enhanced attenuation capacity via blending or layering of adsorbents.     

Adsorption Kinetics of Dyes in Single and Binary Systems Using Cyanoguanidine-Crosslinked Chitosan of Different Deacetylation Degrees

The crosslinking of chitosan with cyanoguanidine shows some advantages, such as the improved the stability in acid solutions and the decrease of adsorbent cost. In this work, cyanoguanidine-crosslinked chitosan and pure chitosan were prepared to apply in the adsorption of Food Yellow 4 (FY4) and Food Blue 2 (FB2), in single and binary systems. Effects of pH and deacetylation degree (DD) of chitosan in adsorption were evaluated. The adsorbents were characterized by Fourier transform infrared spectroscopy and scanning electron microscopy. The kinetic data were analyzed by pseudo-first order, pseudo-second order and Avrami models. The conditions of pH 3 and DD 95% were the more suitable to reach the highest adsorption capacities in all experimental assays. Under these conditions, the adsorption capacities for FY4 were approximately of 392 and 200 mg g^?1 and, for FB2 were approximately of 370 and 184 mg g^?1, respectively, in the single and binary systems. The Avrami model was suitable to represent the kinetic curves in all conditions, and the highest adsorption capacities were found for FY4 in binary aqueous system, being for the pure chitosan of 229 mg g^?1 and crosslinked chitosan of 218 mg g^?1. The Langmuir and extended Langmuir models presented a good fit to the equilibrium data in both systems. It was found that, the chitosan crosslinked with cyanoguanidine improved the chemical stability of chitosan as adsorbent.     

Selection of adsorbents for treatment of leachate: batch studies of simultaneous adsorption of heavy metals

The simultaneous adsorption of copper (Cu), cadmium (Cd), nickel (Ni), and lead (Pb) ions from spiked deionized water and spiked leachate onto natural materials (peat A and B), by-product or waste materials (carbon-containing ash, paper pellets, pine bark, and semi-coke), and synthetic materials (based on urea-formaldehyde resins, called blue and red adsorbents) or mixtures thereof was investigated. The adsorbents that gave the highest metal removal efficiencies were peat A, a mixture of peat B and carbon-containing ash, and a mixture of peat A and blue. At an initial concentration of 5 mg/l for each metal, the removal of each species of metal ion from spiked water and spiked leachate solutions was very good (>90%) and good (>75%), respectively. When the initial concentration of each metal in the solutions was twenty times higher (100 mg/l), there was a noticeable decrease in the removal efficiency of Cu²⁺, Cd²⁺, and Ni²⁺, but not of Pb²⁺. Langmuir monolayer adsorption capacities, q_m, on peat A were found to be 0.57, 0.37, and 0.36 mmol/g for Pb²⁺, Cd²⁺, and Ni²⁺, respectively. The order of metal adsorption capacity on peat A was the same in the case of competitive multimetal adsorption conditions as it was for single-element adsorption, namely Pb²⁺ > Cd²⁺ ≥ Ni²⁺. The results show that peat alone (an inexpensive adsorbent) is a good adsorbent for heavy metal ions.     

The development of low cost adsorbents from clay and waste materials: a review

Increased energy consumption due to industrial growth has increased the levels of carbon dioxide (CO₂) emission being released into the atmosphere. CO₂ emission is a type of greenhouse gas which is a major cause of global warming. Since the issue of CO₂ emissions has drawn much attention in recent years, the development of CO₂ capture technology has become a necessity. Although CO₂ adsorbents are still at the early development stage, it has been suggested that CO₂ adsorbents are the most effective technology in controlling CO₂ emissions. Solid adsorbents have great potential as an alternative method to conventional adsorbents in adsorbing CO₂. In this paper, low cost adsorbents including activated carbon, zeolites, mesoporous silica and clays are discussed in terms of adsorbent preparation methods and CO₂ adsorption capacity. The low cost adsorbents are mainly derived from waste materials such as fly ash, steel slag, red mud, bagasses wastes and wood wastes. Besides that, natural resources such as clays have also been applied as low cost CO₂ adsorbents. Surface modifications have also been applied to the low cost adsorbents, including metal ion exchange and amine impregnation to enhance CO₂ adsorption capacity. In the last section, the current status of CO₂ adsorbents is summarized and future trends are discussed briefly to predict the potential materials which can be applied as CO₂ adsorbents.     

Preparation and performance of arsenate (V) adsorbents derived from concrete wastes

Solid adsorbent materials, prepared from waste cement powder and concrete sludge were assessed for removal of arsenic in the form of arsenic (As(V)) from water. All the materials exhibited arsenic removal capacity when added to distilled water containing 10–700 mg/L arsenic. The arsenic removal isotherms were expressed by the Langmuir type equations, and the highest removal capacity was observed for the adsorbent prepared from concrete sludge with heat treatment at 105 °C, the maximum removal capacity being 175 mg-As(V)/g. Based on changes in arsenic and calcium ion concentrations, and solution pH, the removal mechanism for arsenic was considered to involve the precipitation of calcium arsenate, Ca₃(AsO₄)₂. The enhanced removal of arsenic for the adsorbent prepared from concrete sludge with heat treatment was thought to reflect ion exchange by ettringite. The prepared adsorbents, derived from waste cement and concrete using simple procedures, may offer a cost effective approach for arsenic removal and clean-up of contaminated waters, especially in developing countries.     

Adsorptive Removal of Diuron Herbicide on Carbon Nanotubes Synthesized from Plastic Waste

In this study, carbon nanotubes (CNTs) were synthesized from waste polyethylene bottles and their use as an adsorbent for the removal of diuron herbicide from aqueous solution was evaluated. Batch adsorption was performed by varying adsorbent dosage, initial concentration, contact time, and temperature. Kinetic models applied to experimental data indicated that the pseudo-second-order model had the best fit. The equilibrium data were analyzed using different isotherm models. The adsorption capacity of CNTs for diuron removal, determined using the Hill isotherm, was approximately 40.37 mg/g at 303 K. From thermodynamic studies, the values of ΔH° (kJ/mol) and ΔS° [kJ/(mol K)] were calculated as ?17.307 and ?0.0528, respectively, which suggested that the adsorption process was exothermic. The negative values of ΔG° at three different temperatures indicated that adsorption of diuron on CNTs was favorable.     

Improvement of Cs leaching resistance of solidified radwastes with copper ferrocyanide (CFC)-vermiculite

Cesium removal from de-ionized water, seawater, and limewater using copper ferrocyanide (CFC) and porous media including silica gel, bentonite, vermiculite, and zeolite as adsorbents were investigated; CFC was incorporated with vermiculite to prepare a compound adsorbent for improving the Cs-leaching resistance of solidified borate radwastes. It was shown that the Cs-removal efficiency by CFC, defined as the percentage of cesium removed or adsorpted from solution, was largely affected by pHs of the solutions. Good removal efficiency occurred at pHs ranging from 3 to 12 with the best from 7 to 10. Vermiculite and zeolite were shown to have better removal power than silica gel and bentonite, and vermiculite was chosen to incorporate with CFC to make compound adsorbents because of its good compatibility with CFC floc. Compound adsorbents with different CFC contents were used as additives in the solidification of radioactive borate wastes for improving the cesium leaching resistance of the solidified products. Experimental results showed that the cesium leachability index measured following the method described in ANSI/ANS 16.1 increased from 7.96 to 9.76 by adding 0.25% of a compound adsorbent containing 20% CFC and 80% vermiculite. It indicated that the compound adsorbent is very useful for improving cesium-leaching resistance of the solidified borate wastes.     

炭基载体含氧基团对Mn-Ce双金属吸附剂脱硫活性的影响

以无烟煤、烟煤、褐煤以及工业半焦、烟煤半焦为载体,采用超声辅助加压浸渍法制备了Mn-Ce双金属吸附剂。利用固定床装置对吸附剂的烟气脱硫活性进行了评价,并运用BET、XRD和FTIR技术对其进行了表征。结果表明：吸附剂的脱硫活性主要由焙烧后的金属氧化物提供,金属离子本身无脱硫活性;炭基载体中的酯基是影响金属组分脱硫活性的主要因素,酯基在焙烧过程中分解使得金属组分暴露出来,提高了吸附剂的脱硫活性;中等变质程度的烟煤是制备吸附剂的良好载体,含有适量酯基,使得吸附剂表面金属组分分散均匀。     

Adsorption of malachite green on groundnut shell waste based powdered activated carbon

In the present technologically fast changing situation related to waste management practices, it is desirable that disposal of plant waste should be done in a scientific manner by keeping in view economic and pollution considerations. This is only possible when the plant waste has the potential to be used as raw material for some useful product. In the present study, groundnut shell, an agricultural waste, was used for the preparation of an adsorbent by chemical activation using ZnCl2 under optimized conditions and its comparative characterisation was conducted with commercially available powdered activated carbon (CPAC) for its physical, chemical and adsorption properties. The groundnut shell based powdered activated carbon (GSPAC) has a higher surface area, iodine and methylene blue number compared to CPAC. Both of the carbons were used for the removal of malachite green dye from aqueous solution and the effect of various operating variables, viz. adsorbent dose (0.1-1 g l(-1)), contact time (5-120 min) and adsorbate concentrations (100-200 mg l(-1)) on the removal of dye, has been studied. The experimental results indicate that at a dose of 0.5 g l(-1) and initial concentration of 100 mg l(-1), GSPAC showed 94.5% removal of the dye in 30 min equilibrium time, while CPAC removed 96% of the dye in 15 min. The experimental isotherm data were analyzed using the linearized forms of Freundlich, Langmuir and BET equations to determine maximum adsorptive capacities. The equilibrium data fit well to the Freundlich isotherm, although the BET isotherm also showed higher correlation for both of the carbons. The results of comparative adsorption capacity of both carbons indicate that groundnut shell can be used as a low-cost alternative to commercial powdered activated carbon in aqueous solution for dye removal.     

Removal of Cr6 + and Ni2+ from aqueous solution using bagasse and fly ash

Raw bagasse and fly ash, the waste generated in sugar mills and boilers respectively have been used as low-cost potential adsorbents. Raw bagasse was pretreated with 0.1N NaOH followed by 0.1N CH3COOH before its application. These low-cost adsorbents were used for the removal of chromium and nickel from an aqueous solution. The kinetics of adsorption and extent of adsorption at equilibrium are dependent on the physical and chemical characteristics of the adsorbent, adsorbate and experimental system. The effect of hydrogen ion concentration, contact time, sorbent dose, initial concentrations of adsorbate and adsorbent and particle size on the uptake of chromium and nickel were studied in batch experiments. The Sorption data has been correlated with Langmuir, Freundlich and Bhattacharya and Venkobachar adsorption models. The efficiencies of adsorbent materials for the removal of Cr(VI) and Ni(II) were found to be between 56.2 and 96.2% and 83.6 and 100%, respectively. These results were obtained at the optimized conditions of pH, contact time, sorbent dose, sorbate concentration of 100 mg/l and with the variation of adsorbent particles size between 0.075 and 4.75 mm. The order of selectivity is powdered activated carbon > bagasse > fly ash for Cr(VI) removal and powdered activated carbon > fly ash > bagasse for Ni(II) removal.     

Pyrrolidinium Imides: Promising Ionic Liquids for Direct Capture of Elemental Mercury from Flue Gas

A new approach to vapor phase elemental mercury capture has been explored; this approach exploits an ionic liquid coating layer to oxidize elemental mercury for subsequent immobilization by chelating ligands. The room temperature ionic liquid 1-butyl-1-methyl pyrrolidinium bis(trifluoromethane sulfonyl)imide (P₁₄) was selected for study based on its oxidation potential window, thermal stability, and low vapor pressure. Tests were also completed in which KMnO₄ was added to P₁₄ to form a new ionic liquid, P₁₄–KMnO₄, with a higher oxidation potential. In room-temperature bulk liquid phase capture experiments, 59% of the elemental mercury in the inlet gas was captured using P₁₄ alone; mercury capture using P₁₄–KMnO₄ was quantitative. P₁₄ and P₁₄–KMnO₄ coatings were successfully applied to mesoporous silica substrates and to silica substrates functionalized with mercury chelating ligands. The coating layers were found to be thermally stable up to 300°C. Fixed-bed tests of nonfunctionalized silica coated with P₁₄ showed an elemental mercury uptake of 2.7 mg/g adsorbent at 160°C; at the same temperature, functionalized silica coated with P₁₄–KMnO₄ showed an elemental mercury capacity of at least 7.2 mg/g adsorbent, several times higher than that of activated carbon. The empty bed gas residence time in these tests was 0.04 s. A chelating adsorbent incorporating P₁₄ in the coating layer, may be capable of simultaneous removal of elemental and oxidized mercury from coal combustion flue gases.     

Synthesis of Gum Acacia Capped Polyaniline-Based Nanocomposite Hydrogel for the Removal of Methylene Blue Dye

In this research work, a novel gum acacia capped polyaniline-based nanocomposite hydrogel (GPA NCHs) was developed and evaluated for the adsorptive removal of cationic methylene blue dye (MB) from aqueous solutions. Firstly, Gum acacia (GA) capped Polyaniline (PANI) dispersion was synthesized by using dispersion polymerization. Then, a water-swellable hydrogel network consisting of GA-PANI and acrylamide (AM) was obtained by using N,N′ -methylene-bisacrylamide (MBA) as a cross-linker, and ammonium persulphate/N,N,N′,N′-tetramethylethylenediamine (APS/TMEDA) as an initiating system. The developed materials were characterized by UV–visible, FTIR, XRD, SEM–EDX and TEM techniques. The microscopy studies revealed that GA-PANI nanoparticles have a granular morphological surface with an average size of?~?40–100 nm. Removal of MB dye from aqueous system was performed by adsorption studies in batch equilibrium mode with different dosage of GA-PANI, MB concentration, pH and temperatures. The adsorption data revealed that the absorption capacity of GPA NCHs highly depends on the dosage of GA-PANI, pH and concentration of the MB dye. The maximum percentage of MB removal onto GPA 1.0 NCHs was found to be 89% at pH 10 with a dye concentration of 10 mg L^?1. The equilibrium adsorption data were also analyzed by different models to understand the adsorption process. The results revealed that the adsorption process followed the pseudo-second-order kinetics and it fit well in Langmuir and Freundlich adsorption isotherms with a maximum adsorption capacity of 35.41 mg g^?1. These studies demonstrate that the GPA NCHs could be a promising adsorbent material for the removal of MB dye from contaminated aqueous systems.

     

Fluoride sorption by treated fly ash: kinetic and isotherm studies

High fluoride levels in drinking water have become a critical health hazard. In the present study, the performance of magnesia-loaded fly ash adsorption in the removal of fluoride from aqueous solution was investigated in a batch study. The effect of contact time, dosage, pH, temperature and agitation speed was studied at different values. The maximum removal efficiency was 88 % at 150 min. The effective dose of adsorbent was found to be 2.5 g/l. The optimum pH was found to be at pH 4. Kinetic studies and isotherm studies were also performed to understand the ability of the adsorbents. The monolayer adsorption capacity determined from the Langmuir adsorption equation was found to be 11.61 mg/g. The kinetic measurements suggested the involvement of pseudo-second-order kinetics in adsorption and were controlled by a particle diffusion process. Overall, the results of this study suggest that magnesia-loaded fly ash is an environmentally friendly, efficient and low-cost adsorbent, useful for the removal of fluoride from aqueous solution.     

Insight into the Adsorption Properties of Chitosan/Zeolite-A Hybrid Structure for Effective Decontamination of Toxic Cd (II) and As (V) Ions from the Aqueous Environments

Chitosan/zeolite-A hybrid structure (CS/Z.A) was synthesized and characterized as a multifunctional and environmental adsorbent for the Cd (II) and As (V) ions. The adsorption capacities of CS/ZA for Cd (II) and AS (V) are 170 mg/g and 125 mg/g, respectively which are higher values than several adsorbents in literature. The kinetic study demonstrates Pseudo-First-order behavior for the Cd (II) adsorption process and Pseudo-second order for the As (V) uptake reactions. The Cd (II) and As (V) uptake reactions follow the Freundlich equilibrium behavior with heterogeneous and multilayer adsorption properties. The kinetic and equilibrium studies in addition to the Gaussian energy {6.35 kJ/mol [Cd (II)] and 9.44 kJ/mol [As (V)]} demonstrate physical properties for the Cd (II) adsorption mechanism and more chemical behavior for the As (V) adsorption mechanism. The thermodynamic study declares exothermic, spontaneous, and favorable adsorption reactions for Cd (II) and As (V) by CS/Z.A composite. The CS/Z.A is of significant capacity for Cd (II) and As (V) ions in the existence of other competitive dissolved anions (PO₄^3?, NO₃^?, and SO₄^2?) and other metals [Zn (II), Co (II), and Pb (II)]. Finally, the CS/Z.A composite is a recyclable product and can be applied in effective Cd (II) and As (V) decontamination processes for five runs.

     

煤矸石的改性及其对稀土生产废水中氨氮的吸附

采用热改性、盐酸改性、硫酸改性、碱改性的方法分别制备了4种改性煤矸石吸附剂,研究了吸附工艺条件对4种改性煤矸石吸附剂对稀土生产废水中氨氮去除效果的影响以及吸附机理.实验结果表明:4种改性煤矸石吸附剂吸附氨氮的最佳工艺条件为:吸附剂加入量0.02 g/mL,振荡时间2.5 h,废水pH 7～8;4种吸附剂氨氮去除率大小顺序为:碱改性煤矸石＞硫酸改性煤矸石＞盐酸改性煤矸石＞热改性煤矸石;碱改性煤矸石的氨氮去除率最高,为59.19％;碱改性煤矸石吸附剂对含氨废水中氨氮的吸附较好地符合Langmuir方程和Freundlich方程,在一定程度上符合Temkin方程.