杭州某高校室内空气质量状况调查分析

为了解高校室内污染状况,调查选取杭州市某高校75间教室按照装修完成后时间长短分成5组,分别于2011年3、6月进行氡、氨、甲醛和苯系物(苯、甲苯和二甲苯),浓度的检测.结果显示,甲醛和苯系物浓度与装修完成后时间长短、通风情况、温度、湿度密切相关,装修完成后1.0年内的教室浓度显著高于其余组(P＜0.05).除装修完成后5.0年以上组外,各组甲醛和苯系物含量6月都呈现极显著增高趋势(p＜0.01).所有室内氡和氨浓度均未超标.总体来说,该校室内空气质量状况总体良好,但新建建筑物的室内空气污染存在一定的安全隐患.     

新装饰装修房屋室内空气中的苯系物调查

对新装饰装修房屋室内的一类主要有机苯系污染物进行了调查,调查采用吸附柱采集、GC/MS 和GC-FID测定,检测了321家居室内的苯系物.检出的苯系物有12种,苯平均浓度为0.068 mg/m^3,有86.9%的居室符合《室内空气质量标准》（GB/T18883-2002）规定的限量值,甲苯、二甲苯平均浓度分别为0.14 mg/m^3和0.41 mg/m^3,符合《室内空气质量标准》规定限值的居室分别达85.4%和73.3%.苯系物约占室内空气中TVOC的62%,浓度由低到高分别是苯、甲苯、乙苯和二甲苯,其中二甲苯中的间二甲苯占二甲苯总量的55% .     

室内有害气体的通风净化效应

室内装修材料和家具释放的有害气体严重恶化了室内空气品质,其中甲醛对人体危害尤为突出,而室内通风是清除甲醛行之有效的办法。测试了室内甲醛释放源的释放强度规律,并建立了新装修室内甲醛通风净化的空气动力学模型,数值计算分析了通风情况下室内甲醛的浓度分布特征。结果表明:(1)室内地板和家具的甲醛释放强度均随测试时间呈指数减小;(2)同一通风风速下,装修后第30天时的甲醛浓度较大区域明显减少;(3)在室内人坐姿和站姿呼吸高度(约1.2、1.7m)处,无论风速大小,装修后通风一段时间后室内甲醛浓度均减小,且较低位置(1.2m)甲醛浓度减小更明显;(4)在同种气流组织形式下,较小和较大的通风风速对室内甲醛通风净化效果均不理想,对本研究模型而言,以通风风速2m/s左右时对室内甲醛净化效果较好。     

环境测试舱自吸附甲醛重释放规律与影响因素研究

广泛用于板材污染物释放量测试、空气净化产品净化效果测试等实验中的环境测试舱,往往由于其内壁黏附性杂质而对目标测试物产生不可忽视的自吸附作用,自吸附污染物将作为二次释放源出现重释放,研究目标测试物的自吸附消耗量及重释放规律,探索有效控制措施,有利于对环境测试舱实验应用及室内污染控制提出指导性实际意义。分别选取0.2%甲醛溶液、大芯板作为同一自制玻璃环境测试舱2期实验(I期、Ⅱ期)的不同甲醛释放源,通过近90 d追踪测试,经不同释放源、不同控制条件下舱内壁自吸附甲醛的多次重释放实验,结合非线性拟合分析方法,总结出舱内壁自吸附甲醛重释放甲醛浓度变化符合一阶递增指数函数:y=A1×exp(-x/t1)+y0,(A1<0、t1>0)。曲线参数y0值可用于评价实验条件下测试舱内自吸附甲醛残余量;y0值与环境舱舱体材质、环境温湿度、舱外甲醛浓度及空气交换手段有关,而与释放源及其释放平衡浓度高低无明显关系。大开舱门短时间抽气式空气交换对舱内自吸附甲醛残余有适度清除效果,使y0值降低,同时有利于再次平衡状态的快速建立;而长时间的无动力空气交换,或者自来水洗及去离子水洗等处理手段对舱内壁自吸附甲醛残余无明显清除作用。     

室内甲醛污染被攻克

新装修的房子很长时间里都有一股刺鼻的气味，这是装修材料导致的甲醛、氨、苯等的致癌物质污染。北京亚都科技股份有限公司承担的国家十五攻关项目——建筑室内空气净化器的研制项目取得了突破，成功研制出“装修卫士”新产品，是具有六种功能的创新产品。如“装修卫士2801”在24小时内，可以将30m。内的房间中甲醛浓度下降97％以上，氨浓度下降95％以上，灭菌率90％以上，而且该产品无毒。     

汽车内微环境空气污染的初步探究

为了研究车内的污染水平,在2004-04-10至2004-06-20对车内空气进行了采样和分析.对车龄在2年内的91种型号轿车的车内微环境进行了静态检测,有效检测车辆共计802辆,同时对比检测20辆2002年以前出厂的旧车.检测项目包括甲醛、苯、甲苯、二甲苯和CO等.参照国家室内空气质量标准,新车中甲苯浓度超标率达82%,苯和甲醛浓度的超标率分别为75%和24%.在被检测车辆中,甲醛、苯、甲苯和二甲苯浓度均是新车比旧车高,只有CO浓度是旧车比新车高.初步分析判断苯系物主要来源于车内的胶粘剂,甲醛来自于车椅座套和座垫等,CO来源于发动机排放残留.     

室内空气总挥发性有机物净化实验装置设计及应用

为了探究进气流量和相对湿度对活性炭吸附法和光催化转化法动态净化室内空气中总挥发性有机物(TVOC)的影响,设计了一套包含活性炭吸附器和光催化反应器的多功能空气动态净化实验装置,并利用该装置进行了室内空气净化实验。通过设置不同进气条件(进气流量和相对湿度)对室内空气进行净化实验,采用气相色谱仪对样品TVOC浓度进行检测,并与未经净化处理的空气样品进行对比,计算TVOC去除率。结果表明:该实验装置能够实现连续进气且能对进气流量和相对湿度进行精准调节;随着进气流量增大,活性炭和光催化对TVOC去除率减小;随着进气相对湿度增大,活性炭对TVOC去除率减小,光催化对TVOC的去除率呈现先增大后减小的趋势。以上实验结果为气候舱空气净化系统、家用空气净化器及室内新风过滤系统等动态空气净化系统的设计提供了参考。     

垃圾焚烧飞灰添加对沥青铺路烟气苯系物释放的影响

为探究垃圾焚烧飞灰(以下简称飞灰)添加对沥青铺路烟气中苯系物的影响,实验室模拟研究了不同的温度区间(50～80、80～145、145～165、165～200、200℃恒温)及飞灰添加量(质量分数分别为0、3.0%、4.0%、5.0%)条件下,沥青烟气中苯系物的释放规律。结果表明:温度对苯系物的释放有显著的影响,苯系物释放浓度随着温度的增加而增加,在50～80、80～145、145～165、165～200℃及200℃恒温5个温度区间内苯系物的平均浓度较上一区间分别增加了1.02、2.22、0.50、1.08倍。实验中飞灰的添加对沥青烟气中苯系物的释放浓度无显著影响,但对各单体影响不同。当飞灰添加量为3.0%时,苯、乙苯、二甲苯(间二甲苯、对二甲苯、邻二甲苯)、三甲苯(1,3,5-三甲苯、1,2,4-三甲苯、1,2,3-三甲苯)释放浓度增加了16.78%、20.65%、37.69%、9.72%,随着飞灰添加量的继续增加其浓度增幅逐渐减少。     

上海市机动车尾气VOCs组成及其化学反应活性

采用钢罐采样-气相色谱/质谱法,采集并分析了上海市主要交通干道和隧道废气样品中挥发性有机物(VOCs)的污染水平。分析结果表明,交通干道和隧道废气样品的总挥发性有机污染物(TVOC)质量浓度分别为(227.1±40.9)、(2209.9±1228.0)μg/m3;隧道废气样品中的TVOC浓度是交通干道平均浓度的4.3～15.2倍;交通干道废气样品中VOCs主要组分与隧道废气样品中VOCs主要组分非常类似,说明交通干道废气样品中VOCs主要来源于机动车尾气排放。交通干道废气样品中TVOC的.OH消耗速率为(17.21±4.49)s-1,延安东路隧道和打浦路隧道废气样品中TVOC的.OH消耗速率分别为(300.37±120.78)、(138.09±25.30)s-1,烯烃对TVOC的.OH消耗速率贡献最大,其对废气化学反应活性贡献率在70%以上。交通干道和隧道废气样品中关键活性组分是C2～C5的烯烃组分,这些组分也是机动车尾气中的特征污染物,因此可以判断机动车尾气是上海市大气化学反应活性的最大贡献者。     

蚊香类散发污染物排放因子及颗粒物分布特征研究

应用大型空气质量实验舱平台,分别测试盘式固体蚊香、片型电蚊香和液体电蚊香的PM2.5和主要气态污染物散发量。采用定释放浓度法,获得PM2.5和主要气态污染物排放因子。结果显示,盘式固体蚊香、液体电蚊香、片型电蚊香的PM2.5排放因子分别为12.9、1.3、2.6mg/h,总挥发性有机物(TVOC)排放因子分别为103.4、69.5、58.8mg/h,甲醛排放因子分别为16.0、8.9、12.5mg/h,3种蚊香排放的主要苯系污染物排放水平相当,此外盘式固体蚊香还散发CO,排放因子为925.4mg/h。对盘式固体蚊香散发颗粒物的数浓度谱分布进行了拟合分析,发现数浓度谱分布具有良好的自模性,拟合得出计数中位径(CMD)为90nm,几何标准差(GSD)为1.65;假设蚊香释放颗粒物为密度1.4g/cm3的球形颗粒,利用质量浓度和数浓度谱分布特征反算得出各类蚊香散发颗粒物的数浓度排放因子。通过案例计算,发现房间在正常通风条件(换气次数为2.0次/h)下使用各类蚊香时散发的TVOC浓度将超标1.8~3.2倍,甲醛超标1.5~3.0倍;盘式固体蚊香散发的PM2.5超标近1.5倍,CO超标1.7倍。对封闭环境下,通风条件很差(换气次数为0.5次/h),此时所有污染物浓度将增大4倍,污染更加严重。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.