Influence of metal oxides on PCDD/Fs formation from pentachlorophenol

Chlorophenols (ClPhs) are considered as important precursors for PCDD/Fs formation. The influences of series of metal oxides including MgO, Al2O3, CaO, BaO, TiO2, V2O5, MnO2, Fe2O3, Co3O4, CuO, Ag2O, ZnO, HgO, SnO, PbO, La2O3, CeO2, and Eu2O3 on PCDD/Fs formation from pentachlorophenol (PCP) were investigated in a laboratory-scale reactor. The results indicated that most of the above metal oxides have obvious suppressing effects on the total amount of PCDD/Fs formation from precursor PCP except for CuO, ZnO, MnO2, TiO2 and Co3O4 with promotion effects at 280 degrees C for 2 h. Although MgO, Al2O3, Fe2O3, PbO, La2O3 and Eu2O3 could reduce the amount of octachlorinated dibenzo-p-dioxin (OCDD), they promote the formation of more toxic 1,2,3,4,6,7,8-HpCDD at the same time. The total suppressing efficiencies of several metal oxides including CaO, BaO, PbO, Ag2O, HgO and SnO which have lower Z/r (charge to radius ratio) <2 are all over 90%. The theories of generalized acid-base and atomic parameter (Z/r) were used to speculate the effecting mechanisms. The factors including time and temperature on suppressing efficiencies of CaO, BaO and PbO have also been studied in the present paper. The results showed that the total suppressing efficiencies of CaO, BaO and PbO increase with the increase of heated time and temperature.     

Zr-Fe双组分复合除砷吸附剂的优化制备及性能评价

实验发现,铁氧化物或铁的羟基氧化物对As(V)有较好的吸附性能,而锆氧化物或锆水合氧化物则对As(Ⅲ)有优异的吸附选择性,但其使用的pH通常要在9的条件下。通过简单的共沉淀法制备了Zr-Fe双组分复合吸附剂,在制备过程中通过优化制备条件如:沉淀剂浓度、金属离子总浓度、金属离子配比、反应温度、反应时间及吸附剂价格等因素,最终合成出了对As(V)和As(Ⅲ)都具有良好吸附能力的吸附剂。这种吸附剂在中性条件下对As(V)和As(Ⅲ)的最大吸附量为62 mg/g和118 mg/g。     

Zr—Fe双组分复合除砷吸附剂的优化制备及性能评价

实验发现，铁氧化物或铁的羟基氧化物对As（V）有较好的吸附性能，而锆氧化物或锆水合氧化物则对As（Ⅲ）有优异的吸附选择性，但其使用的pH通常要在〉9的条件下。通过简单的共沉淀法制备了Zr-Fe双组分复合吸附剂，在制备过程中通过优化制备条件如：沉淀剂浓度、金属离子总浓度、金属离子配比、反应温度、反应时间及吸附剂价格等因素，最终合成出了对As（V）和As（Ⅲ）都具有良好吸附能力的吸附剂。这种吸附剂在中性条件下对As（V）和As（Ⅲ）的最大吸附量为62mg／g和118mg／g。     

Low-cost adsorbents from bio-waste for the removal of dyes from aqueous solution

Activated carbons (ACs) were developed from bio-waste materials like rice husk and peanut shell (PS) by various physicochemical activation methods. PS char digested in nitric acid followed by treatment at 673 K resulted in high surface area up to ～585 m²/g. The novelty of the present study is the identification of oxygen functional groups formed on the surface of activated carbons by infrared and X-ray photoelectron spectroscopy and quantification by using temperature programmed decomposition (TPD). Typical TPD data indicated that each activation method may lead to varying amounts of acidic and basic functional groups on the surface of the adsorbent, which may be a crucial factor in determining the adsorption capacity. It was shown that ACs developed during the present study are good adsorbents, especially for the removal of a model textile dye methylene blue (MB) from aqueous solution. As MB is a basic dye, H₂O₂-treated rice husk showed the best adsorption capacity, which is in agreement with the acidic groups present on the surface. Removal of the dye followed Langmuir isotherm model, whereas MB adsorption on ACs followed pseudo-second-order kinetics.     

Photocatalytic oxidation of NOx using composite sheets containing TiO2 and a metal compound

The photocatalytic oxidation of nitrogen oxides (NO(x)) over titanium dioxide (TiO(2)) sheets containing metal compounds (MCs) had been studied. Calcium oxide (CaO), magnesium oxide (MgO), calcium carbonate (CaCO(3)), aluminium oxide (Al(2)O(3)) and ferric oxide (Fe(2)O(3)) were used as MCs. Al(2)O(3) and Fe(2)O(3) added to the TiO(2) sheet did not affect the photooxidation of nitrogen oxides (NO(x)). The CaO sheet treated with TiO(2) sol had the greatest efficiency as a NO(x) remover under UV irradiation. It is believed that CaO has a high adsorptivity for nitrogen dioxide (NO(2)) and nitric acid (HNO(3)). The amount of NO(x) removed by a TiO(2) sheet including MC showed a tendency to increase with increasing pH of the MC suspension, i.e. there is a good correlation between the alkalinity of the MC and the retention of NO(2) and HNO(3).     

Adsorption of ammonium on biochar prepared from giant reed

Giant reed was used as precursor for making biochar in order for the adsorption of NH₄ ⁺–N from aqueous solution. And the adsorption of the product to NH₄ ⁺–N was examined. The surface features of biochar were investigated by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy/energy dispersive spectrometer (SEM-EDS), and X-ray diffraction (XRD). XRD patterns showed several peaks and correspond to the high amount of crystalline material. The crystals contain KCl, K₂O, CaO, MgO, and SiO and possess high surface area which enhances adsorption. The influence of different parameters such as initial concentration, adsorption time, pH, and ionic strength has been carried out. The adsorption could reach equilibrium through 24 h reaction and had the best adsorption amount at the solution pH values from 7 to 9. The cation has great influence on the adsorption of NH₄ ⁺–N, whereas the anion exerted a weaker effect. The adsorption followed pseudo-first-order and pseudo-second-order models. And the intraparticle diffusion and desorption studies further elucidated that the mechanism of adsorption on the product was ion exchange. The product equilibrium data was well described by the Langmuir and Freundlich model. The maximum adsorption capacities were 1.490 mg/g. Biochar derived from giant reed at 500 °C was suggested as a promising adsorbent for the removal of NH₄ ⁺–N from slightly polluted wastewater.     

Adsorption behavior of light green anionic dye using cationic surfactant-modified wheat straw in batch and column mode

An agricultural by-product, natural wheat straw (NWS), was soaked in 1 % cationic surfactant (hexadecylpyridinium bromide, CPB) solution for 24 h (at 293 K), and modified wheat straw (MWS) was obtained. Analysis of FTIR, XFR, and nitrogen element showed that CPB was adsorbed onto surface of NWS. Then, MWS was used as adsorbent for the removal of light green dye (LG, anionic dye) from aqueous solution. The experiment was performed in batch and column mode at room temperature (293 K). Sodium chloride (up to 0.1 mol/L) existed in solution was not favor of LG dye adsorption. The equilibrium data were better described by Langmuir isotherm, and adsorption capacity of q _m from Langmuir model was 70.01?±?3.39 mg/g. In fixed-bed column adsorption mode, the effects of initial LG concentration (30, 50, 70 mg/L) and flow rate (6.5, 9.0, 14.5 mL/min) on adsorption were presented. Thomas and modified dose–response models were used to predict the breakthrough curves using nonlinear analysis method, and both models can fit the breakthrough curves. Theoretical and experimental breakthrough curves were drawn and compared. The results implied that MWS can be used as adsorbent material to remove LG from aqueous solution.     

Trichloroethylene decomposition and in-situ dry sorption of Cl-products by calcium oxides prepared from hydrated limes

A comparison of CaOs produced by calcining two types of hydrated lime and calcium carbonate was made for decomposition of trichloroethylene and in-situ dry sorption of the decomposed Cl-products using a lab-scale gas flow type tubular packed bed reactor. About 20 mg of CaO sample was mixed with about 2 g of Al₂O₃ particles and packed in the reactor and allowed to react with a flowing standard gas containing 500 ppm of C₂HCl₃ (N₂ balance) at 673 and 873 K, under the condition that the reaction of CaO with C₂HCl₃ might be completed within a few hours.It was found that no thermal decomposition of C₂HCl₃ at or below 673 K was observed in a reactor packed only with Al₂O₃ particles. However, a considerable amount of decomposition of C₂HCl₃ was obtained in a reactor packed with CaO and Al₂O₃, even at 673 K. For 1 mol of CaO prepared by calcining highly reactive Ca(OH)₂ at 673 K, decomposition of 0.42 mol of C₂HCl₃ and in-situ absorption product of 0.53 mol of CaCl₂ were obtained. At 873 K, about 46% of C₂HCl₃ was thermally decomposed. The total amount of C₂HCl₃ decomposed in CaO-Al₂O₃ particle bed at 873 K became nearly twice larger than that at 673 K. For 1 mol of CaO prepared by calcining highly reactive Ca(OH)₂ at 873 K, decomposition of 0.59 mol of C₂HCl₃ and in-situ absorption product of 0.67 mol of CaCl₂ were obtained. Small amounts of C₂Cl₂, C₂Cl₄, CCl₄, etc. were detected during decomposition of C₂HCl₃ at 673 and 873 K.It was recognized that the data on decomposition of C₂HCl₃ as well as in-situ dry sorption of Cl-products in CaO particle bed were correlated with specific surface area of the CaO employed.     

Dependence of mechanochemically induced decomposition of mono-chlorobiphenyl on the occurrence of radicals

Mechanochemically induced dechlorination of mono-chlorobiphenyl (BP-Cl) on the surfaces of metal oxides was compared with that on metal hydroxides, using the three metals of Mg, Al, and La as examples. The metal oxides, such as gamma-alumina (gamma-Al2O3), magnesium oxide (MgO) and lanthanum oxide (La2O3) showed an efficient ability to dechlorinate the BP-Cl; however, BP-Cl remained in the ground samples when the hydroxides were used. From the product analysis using gas chromatography/mass spectrometry (GC/MS) and electron spin resonance (ESR) measurements, it was confirmed that the charge transfer from the O2- site on the surface of the oxide additives due to the intense grinding has plays a significant role in the decomposition of the chlorinated compound. Based on the observed dependence of the dechlorination on the radical occurrence, some practical methods were proposed to improve the destruction efficiency of the chlorinated organic compounds.     

高比表面积活性炭的制备及对Cr(Ⅵ)吸附的研究

以椰树壳为原料,运用水蒸汽和二氧化碳复合物理活化法在4 h内制备了2 162.84 m2/g的高比表面积活性炭,其孔径分布范围为1.1~2.5 nm。应用此吸附剂考察了溶液pH、吸附剂用量、接触时间和初始浓度对Cr(VI)离子吸附效果的影响,并讨论了固定吸附床中不同溶液流量对Cr(VI)去除效果的影响。结果表明:在温度为298 K、溶液pH为1.96、吸附剂用量为0.10 g、铬离子初始浓度为100 mg/L与接触时间为70 min的条件下,活性炭对铬离子具有较高的吸附容量,去除率高达99.32%;铬离子在吸附床中的穿透曲线具有陡峭的传质锋面,但随着铬离子溶液流量的增大脱除果率降低。     

改性甘蔗渣吸附废水中低浓度Cu2+的研究

利用离子液氯化-1-己基-3-甲基咪唑对甘蔗渣进行改性,利用改性甘蔗渣吸附去除模拟废水中低浓度的Cu2+,并对比了较优条件下甘蔗渣改性前后的Cu2+吸附性能.结果表明,溶液pH、改性甘蔗渣投加量、吸附时间对改性甘蔗渣吸附Cu2+均有一定的影响,较佳的溶液pH为5.41、改性甘蔗渣投加量为0.30 g、吸附时间为130 min;吸附温度升高Cu2+吸附率反而降低,因此选择在室温下进行吸附反应为宜;在以上较优条件下,改性甘蔗渣和甘蔗渣的Cu2+吸附率分别为83.20％和53.83％,前者的Cu2+吸附率提高了30.35％.     

Silane removal at ambient temperature by using alumina-supported metal oxide adsorbents

Copper, zinc, and cerium oxide adsorbents supported on alumina were used to remove silane gas (SiH4). The adsorbents were prepared using a coprecipitation method and characterized by the inductively coupled plasma mass spectrometry, X-ray powder diffractometer, and Brunauer-Emmett-Teller method (BET). The silane removal efficiency and adsorption capacity of the adsorbents were investigated in this study. Test results showed that the adsorbents containing active species had a removal efficiency >99.9% for SiH4 before breakthrough. Adsorbents containing mixed oxides (CuO-CeO2/ Al2O3 and CuO-ZnO/Al2O3), which showed well-dispersed active species and high BET surface areas, had a greater adsorption capacity than the adsorbents containing single metal oxide. However, when the CuO-ZnO/ Al2O3 adsorbents contain >40 wt% of active metal oxides, the increase of active species lowered the BET surface area leading to a decrease of the adsorption capacity. Additionally, when the content of the active metal oxides was between 20% and 40%, the CuO-ZnO/Al2O3 adsorbents demonstrated higher adsorption capacity.     

Removal of arsenic(III,V) by a granular Mn-oxide-doped Al oxide adsorbent: surface characterization and performance

In order to remove arsenic (As) from contaminated water, granular Mn-oxide-doped Al oxide (GMAO) was fabricated using the compression method with the addition of organic binder. The analysis results of XRD, SEM, and BET indicated that GMAO was microporous with a large specific surface area of 54.26 m^2/g, and it was formed through the aggregation of massive Al/Mn oxide nanoparticles with an amorphous pattern. EDX, mapping, FTIR, and XPS results showed the uniform distribution of Al/Mn elements and numerous hydroxyl groups on the adsorbent surface. Compression tests indicated a satisfactory mechanical strength of GMAO. Batch adsorption results showed that As(V) adsorption achieved equilibrium faster than As(III), whereas the maximum adsorption capacity of As(III) estimated from the Langmuir isotherm at 25 °C (48.52 mg/g) was greater than that of As(V) (37.94 mg/g). The As removal efficiency could be maintained in a wide pH range of 3~8. The presence of phosphate posed a significant adverse effect on As adsorption due to the competition mechanisms. In contrast, Ca²⁺ and Mg²⁺ could favor As adsorption via cation-bridge involvement. A regeneration method was developed by using sodium hydroxide solution for As elution from saturated adsorbents, which permitted GMAO to keep over 75% of its As adsorption capacity even after five adsorption–regeneration cycles. Column experiments showed that the breakthrough volumes for the treatment of As(III)-spiked and As(V)-spiked water (As concentration = 100 μg/L) were 2224 and 1952, respectively. Overall, GMAO is a potential adsorbent for effectively removing As from As-contaminated groundwater in filter application.

     

Adsorption Behavior of Toluene on Modified 1X Molecular Sieves

In this paper, the toluene adsorption/desorption properties of modified 13X molecular sieves (M-13X) are discussed. M-13X molecular sieves were prepared by acidic and steam treatments of 13X molecular sieves. The structural parameters of M-13X were evaluated and compared with those of other molecular sieves (HY, HZSM-5, Cs7NaMOR, and a commercial 13X). The results show that the specific surface area, average pore diameter, and pore volume of M-13X were 414.17 m²/g, 2.98 nm, and 0.31 mL/g, respectively. The pore size distribution of M-13X was 1.8–3.0 nm. Because of its larger Si/Al ratio (Si/Al = 6.77), the hydrophobicity of M-13X is much higher than that of 13X (Si/Al = 1.28), indicating that it is particularly well suited to toluene control applications. The saturation adsorption capacity of M-13X was 0.045 g/g for simulated toluene at a temperature of 293 K and a relative humidity of 50%. The optimal regeneration temperature of M-13X was 473 K for 120 min with a hot air flow rate of 140 L/min.

Implications: The modified 13X molecular sieves (M-13X) are adsorbents with a high adsorption capacity and great hydrophobicity, suitable for the treatment of VOCs. The purpose of the present investigation is to provide a practical guide for their design.     

Fluoride removal performance of a novel Fe-Al-Ce trimetal oxide adsorbent

A trimetal oxide was developed as a fluoride adsorbent by coprecipitation of Fe(II), Al(III) and Ce(IV) salt solutions with a molar ratio of 1:4:1 under alkaline condition. The material retained amorphous structure and maintained relatively stable fluoride adsorption performance at calcination temperatures lower than 600 degrees C. The optimum pH range for fluoride adsorption was 6.0-6.5 and the adsorbent also showed high defluoridation ability around pH 5.5-7.0, which is preferable for actual application. A high fluoride adsorption capacity of 178 mg g(-1) was acquired under an equilibrium fluoride concentration of 84.5 mg l(-1), adsorbent dose of 150 mg l(-1) and pH 7.0. The adsorption isotherm could be better described by the two-site Langmuir model than the one-site model, suggesting the existence of two types of active sites on the adsorbent surface. Coexistence of high concentrations of phosphate or arsenate only led to partial inhibition of fluoride adsorption, which further suggests the existence of heterogeneous adsorption sites. Sulfate and chloride did not affect fluoride adsorption, and nitrate influenced it only when the concentration of NO(3)(-)-N exceeded 50 mg l(-1). A high desorption efficiency of 97% was achieved by treating fluoride loaded Fe-Al-Ce oxide with NaOH solution at pH 12.2. A column experiment using the adsorbent fabricated into 1mm pellets was performed at an initial fluoride concentration of 5.5 mg l(-1), space velocity of 5h(-1) and pH of 5.8, and 2240 bed volumes were treated with the effluent fluoride under 1.0 mg l(-1).     

Pore structure effects on Ca-based sorbent sulfation capacity at medium temperatures: activated carbon as sorbent/catalyst support

The reaction between three different Ca-based sorbents and SO2 were studied in a medium temperature range (473-773 K). The largest SO2 capture was found with Ca(OH)2 at 773 K, 126.31 mg SO2 x g Ca(OH)2(-1), and the influence of SO2 concentration on the sorbent utilization was observed. Investigations of the internal porous structure of Ca-based sorbents showed that the initial reaction rate was controlled by the surface area, and once the sulfated products were produced, pore structure dominated. To increase the surface area of Ca-based sorbents available to interact with and retain SO2, one kind of CaO/ activated carbon (AC) sorbent/catalyst was prepared to study the effect of AC on the dispersion of Ca-based materials. The results indicated that the Ca-based material dispersed on high-surface-area AC had more capacities for SO2 than unsupported Ca-based sorbents. The initial reaction rates of the reaction between SO2 and Ca-based sorbents and the prepared CaO/AC sorbents/catalysts were measured. Results showed that the reaction rate apparently increased with the presence of AC. It was concluded that CaO/AC was the active material in the desulfurization reaction. AC acting as the support can play a role to supply O2 to increase the affinity to SO2. Moreover, when AC is acting as a support, the surface oxygen functional group formed on the surface of AC can serve as a new site for SO2 adsorption.     

Effective adsorbent for arsenic removal: core/shell structural nano zero-valent iron/manganese oxide

Recently, nano zero-valent iron (nZVI) has emerged as an effective adsorbent for the removal of arsenic from aqueous solutions. However, its use in various applications has suffered from reactivity loss resulting in a decreased efficiency. Thus, the aim of this study was to develop an effective arsenic adsorbent as a core/shell structural nZVI/manganese oxide (or nZVI/Mn oxide) to minimize the reactivity loss of the nZVI. As the major result, the arsenic adsorption capacities of the nZVI/Mn oxide for As(V) and As(III) were approximately two and three times higher than that of the nZVI, respectively. In addition, the As(V) removal efficiency of the nZVI/Mn oxide was maintained through 4 cycles of regeneration whereas that of the nZVI was decreased significantly. The enhanced reactivity and reusability of the nZVI/Mn oxide can be successfully explained by the synergistic interaction of the nZVI core and manganese oxide shell, in which the manganese oxides participate in oxidation reactions with corroded Fe²⁺ and subsequently retard the release of aqueous iron providing additional surface sites for arsenic adsorption. In summary, this study reports the successful fabrication of a core/shell nZVI/Mn oxide as an effective adsorbent for the removal of arsenic from aqueous solutions.     

Montmorillonite-Cu(II)/Fe(III) oxides magnetic material as adsorbent for removal of humic acid and its thermal regeneration

In this work, the adsorption features of montmorillonite and the magnetic properties of Cu(II)/Fe(III) oxides were combined in a material to produce magnetic adsorbent, which can be separated from the medium by a simple magnetic process after adsorption. The magnetic material is effective for the removal of humic acid. At pH 6.1, 96% removal was observed from 4.4 mg l(-1) humic acid solution containing 0.02 M NaCl. The adsorption is pH and ionic strength dependent. Adsorption is favored at lower pH values and dissolved NaCl can enhance the adsorption. The adsorption mechanism of humic acid to the magnetic material was suggested to be the ligand exchange reaction between carboxylic groups of humic acid molecules and the magnetic material surface. The magnetic material can be thermally regenerated. The temperature and time required to achieve good regeneration efficiency were determined to be 300 degrees C and 3 h, respectively. The regenerated adsorbent is still magnetic and approximately has as high specific saturation magnetization and good adsorption capacities as the as-prepared adsorbent.     

“氧化镁/活性炭”新型吸附剂的制备及其对Cr(VI)的吸附研究

以氯化镁和造纸草浆黑液为原料，采用物理活化法制得“氧化镁/活性炭”新型吸附剂，其比表面积（BET）为388.96 m²/g、总孔容积为0.40 mL/g。测定了这种吸附剂对水中Cr(VI)的吸附性能，考察了吸附时间、pH值、吸附剂投加量、初始浓度等因素对Cr(VI)的吸附量和脱除率的影响，研究所得吸附水溶液中Cr(VI)的最佳条件为：吸附时间为120 min，吸附剂投加量为2 g/L，pH值为2。“氧化镁/活性炭”新型吸附剂对Cr(VI)的吸附过程符合Freundlich等温式。     

Adsorption of natural organic matter from waters by iron coated pumice

Natural pumice particles were used as granular support media and coated with iron oxides to investigate their adsorptive natural organic matter (NOM) removal from waters. The impacts of natural pumice source, particle size fraction, pumice dose, pumice surface chemistry and specific surface area, and NOM source on the ultimate extent and rate of NOM removal were studied. All adsorption isotherm experiments were conducted employing the variable-dose completely mixed batch reactor bottle-point method. Iron oxide coating overwhelmed the surface electrical properties of the underlying pumice particles. Surface areas as high as 20.6m(2)g(-1) were achieved after iron coating of pumice samples, which are above than those of iron coated sand samples reported in the literature. For all particle size fractions, iron coating of natural pumices significantly increased their NOM uptakes both on an adsorbent mass- and surface area-basis. The smallest size fractions (<63 microm) of coated pumices generally exhibited the highest NOM uptakes. A strong linear correlation between the iron contents of coated pumices and their Freundlich affinity parameters (K(F)) indicated that the enhanced NOM uptake is due to iron oxides bound on pumice surfaces. Iron oxide coated pumice surfaces preferentially removed high UV-absorbing fractions of NOM, with UV absorbance reductions up to 90%. Control experiments indicated that iron oxide species bound on pumice surfaces are stable, and potential iron release to the solution is not a concern at pH values of typical natural waters. Based on high NOM adsorption capacities, iron oxide coated pumice may be a promising novel adsorbent in removing NOM from waters. Furthermore, due to preferential removal of high UV-absorbing NOM fractions, iron oxide coated pumice may also be effective in controlling the formation of disinfection by-products in drinking water treatment.