光能自养生物膜形成机制及脱氮影响因素的研究进展

光能自养生物膜是一个由复杂微生物群落构成的相对稳定的微生态系统,微生物细胞及非生物物质镶嵌在微生物分泌的有机聚合物基质上,其显著特征是膜表面寄居着光能自养生长的微生物,并能在碳源缺乏条件下完成生物脱氮.总结了光能自养生物膜的形成机制,概述了光照、温度、微生物种类、营养物浓度对光能自养生物膜脱氮的影响,指出光能自养生物膜...     

可生物降解塑料与沸石载体体系对硝酸盐氮污染地下水的生物修复研究

生物反硝化是修复地下水硝酸盐氮污染的一种有效途径。为进一步确定异养反硝化碳源与载体投加量的配比,取用污水处理厂活性污泥为微生物来源,以可生物降解塑料为新型固相碳源,沸石为微生物载体,设计了9组固相碳源与载体不同配比的柱实验,旨在遴选出可生物降解塑料和沸石的最优配比。同时考察在最优配比时,不同进水硝酸盐氮浓度下的硝酸盐氮去除率、填料降解率、生物膜附着量、生物膜附着效率、反硝化效率等反应特性。结果表明,可生物降解塑料∶沸石(质量比)=2∶1为最优配比。在最优配比下,进水硝酸盐氮质量浓度为40~100mg/L时,异养反硝化对硝酸盐氮具有很好的去除效果(最终去除率均在99%以上),且能够保持较高的反硝化效率,同时载体负载微生物的性能稳定。     

响应曲面法优化固相反硝化的工艺条件

以一种新型可降解材料PLA/PHBV共混物为碳源和生物膜载体,对硝酸盐污染水进行反硝化脱氮。在温度为(29±1)℃,pH为(7.5±0.2)条件下,利用响应曲面法考察了进水硝态氮浓度、水力停留时间(HRT)和出水硝态氮浓度之间的关系,建立了以出水硝态氮浓度为响应值的二次多项式回归模型,模型预测值与实验值能很好吻合。方差分析结果表明,进水硝态氮浓度和HRT及其交互作用对响应值均具有显著性影响(P<0.01)。     

基于化学与生物膜耦合深度脱除地下水中硝酸盐氮

我国华北地区超过80%的地下水受到污染,其中硝酸盐氮的污染日益严重,威胁着人类健康。基于单质铁去除地下水中硝酸盐氮,因伴随氨氮的产生而受限制;生物反硝化脱氮因地下水中碳源不足无法满足脱氮要求。采用自制的微电解化学催化固体颗粒与天然生物质构成耦合生物载体,通过自养与异养反硝化耦合深度脱除地下水中硝酸盐氮,并建立了地下水易位好氧、厌氧深度脱氮新工艺。结果表明:好氧反应器在HRT为12 h、DO为2.0～3.0 mg·L-1的条件下,硝酸盐氮平均去除率≥91.24%;厌氧反应器在HRT为14 h的条件下,硝酸盐氮平均去除率≥96.32%;反应器中微电解化学催化固体颗粒可为自养反硝化菌提供电子,生物质可为微生物提供必要的有限碳源,硝酸盐氮的脱除是自制微电解化学催化固体颗粒与生物膜耦合作用的结果。出水均无亚硝酸盐氮和氨氮积累。此技术可为受污染地下水的修复提供理论依据。     

某污水处理厂A2/O工艺冬季生物反硝化过程的影响因素研究

针对污水处理厂冬季反硝化脱氮效率不佳的问题,以常州市某污水处理厂A~2/O工艺为研究对象,模拟探讨了不同外加碳源、碳源投加量、溶解氧(DO)和硝态氮浓度对生物处理系统反硝化脱氮能力的影响。结果表明,外加有机碳源对系统的反硝化效能有明显的强化效果。3种外加有机碳源(乙酸、乙醇和乙酸钠)中,乙酸为最佳碳源。当乙酸投加量为40mg/L时,系统反硝化脱氮效率最高,比反硝化速率可达1.964mg/(g·h),反硝化碳耗最少,为7.14 mg/mg。DO与比反硝化速率成反比,DO≤0.20mg/L时,反硝化能力最强。硝态氮初始质量浓度为20mg/L左右时,反硝化能力最强。在实际工程应用中,可以通过提高硝化效果或直接调整回流比实现反硝化脱氮最优条件,将有助于提高系统的冬季脱氮效果。     

碳源强化下的硫自养/异养反硝化协同作用

为强化硫自养反硝化过程,通过向连续稳定运行的硫自养反硝化反应器内投加少量碳源以进行强化,乙酸钠投加量分别为5.99、11.98、23.96 mg·L~(-1)。分析投加前后反应器内硝氮、COD、硫酸根和耗碱量的变化;研究了碳源强化下硫自养反硝化运行效能及反应机理。结果表明,投加少量碳源可增强自养反硝化过程硝氮的去除效果;在3种碳源投加量条件下,COD的利用率均大于85%,但硫酸盐生成量并未减少;在5.99 mg·L~(-1)碳源投加量下,系统实际耗碱量大于以硫酸根和COD计的理论耗碱量,而在11.98 mg·L~(-1)和23.96 mg·L~(-1)投加量下,实际耗碱量均介于2种理论值之间。在投加少量碳源后,自养反硝化脱氮效果明显提高,异养反硝化趋势随着碳源投加量的增加而增加。     

以聚己内酯作为生物反硝化固体碳源的研究

为解决水体因低碳氮比而导致脱氮效率差的问题,将颗粒聚己内酯(PCL)重新塑形为阶梯环状,研究其作为反硝化过程的生物膜载体与固相碳源的反硝化性能。结果表明,在静态实验中,平均反硝化速率为8.57 mg NO3-N/(L·h);反硝化过程为零级反应。连续填充床实验中,超过90%的硝酸盐可被去除,出水NO2-N质量浓度低于0.20 mg/L;出水NH3-N质量浓度略有上升;出水溶解性有机碳(DOC)先上升后降低至1 mg/L左右。电子扫描显微镜扫描显示,PCL阶梯环反应表面空隙率较高,表面生物膜以杆菌为主,反应后被明显腐蚀;液相色谱检测显示PCL阶梯环分子量反应前后略有下降,其结构未受到破坏;表明该材料适合作为反硝化反应的碳源的同时,又可以作为载体供微生物附着生长。     

以聚丁酸丁二醇酯为碳源去除含盐水体硝酸盐的研究

以可生物降解聚合物为碳源和生物膜载体可以解决异养反硝化有机碳源的添加不足或过量的问题.在序批式反应条件下,以聚丁酸丁二醇酯(PBS)为碳源和生物膜载体,对含盐水体异养反硝化过程中的细菌群落特征进行了研究.结果表明,试验条件下硝酸盐可以得到很好的去除,虽然有亚硝酸盐的明显积累,但最终被降低.硝酸盐的存在会降低含PBS水体中溶解性有机物的含量.应用变性梯度凝胶电泳和16S rDNA的方法鉴别到的细菌包括:Pseudomonas stutzeri,Pseudomonas sp.,Alteromonas sp.,Marinobacter salsuginis,Thalassospira xianheensis,Itellibacter vladivostokensis,Euplotopsis encysticus,Alcanivorax venustensis,Halomonas sp.,Agrobacterium tume aciens,Pannonibacter phragmitetus,Vitellibacter vladivostokensis.试验结果表明,反硝化条件下PBS具有较好的可生物降解性和明显的NO3--N去除能力,是比较理想的低C/N含盐水体异养反硝化碳源.     

固体碳源反硝化滤池脱氮效果及沿程生化特性

在污水处理工艺末端嵌入固体碳源反硝化滤池,可以不改变污水处理厂的原有工艺提高总氮去除效率,方便应对污水厂的提标压力和低碳源污水的脱氮问题。针对生化池尾水硝酸盐特性,以聚己内酯(PCL)作为填充床构建了固体碳源反硝化生物滤池,研究了该反应器的脱氮性能以及生物滤池的沿程生物量和微生物群落结构。结果表明,TN为32.0~37.7 mg·L~(-1)、硝态氮为30.2~34.9 mg·L~(-1)的生化池尾水进入该固体碳源反硝化池后,在HRT为1.5 h的情况下,出水TN在1.1~3.5 mg·L~(-1)之间,硝态氮低于1 mg·L~(-1),平均去除率均大于94%。研究发现,固体碳源反硝化滤池对硝态氮的转化去除主要发生在40 cm填料以下;生物量的大小也随滤层高度的增加逐渐降低,且与滤层高度呈良好的线性负相关关系(y=-0.471x+38.77,R~2=0.976)。采用PCR-DGGE技术研究了固体碳源反硝化滤池的沿程微生物群落结构特征,发现滤层底部(进水端)尽管生物量多,但微生物多样性低,滤池的中部是生物多样性最丰富的区域,香农威尔指数分别为1.95和2.40。DGGE图谱特征条带的16S rDNA序列分析表明生物膜中微生物变形菌门(Proteobacteria)占优势,主要微生物包括能降解PCL的细菌Comamonas,以及常见的反硝化细菌Dechloromonas、Rubrivivax和发酵产乙酸的硫酸盐还原菌Desulfobacter,从微生物群落关系结构角度支撑了固体碳源反硝化过程的顺利进行。     

3DBER-S阴极nirS型反硝化菌群的分析

为探究低碳氮比条件下3DBER-S(三维电极生物膜与硫自养耦合脱氮工艺)阴极反硝化菌群特征、强化脱氮机制,在TOC/TN=0.36的进水条件下稳定运行反应器,运用nir S基因克隆文库方法,分析了3DBER-S阴极生物膜反硝化菌群结构。结果表明,在3DBER-S阴极生物膜上反硝化菌中,β变形菌(β-proteobacteria)是优势菌种,占细菌总数的59.22%。其中,所占比例最大的是异养菌,包括与固氮弧菌属(Azoarcus tolulyticus)和趋磁螺菌(Magnetospirillum magneticum)类似的细菌,分别占44.74%和21.05%。能够分别利用硫单质或氢气作为电子供体进行反硝化脱氮的Sulfuricella denitrifican、高氯酸盐降解菌(Dechlorospirillum sp.)和陶厄氏菌属(Thauera)三者所占比例之和达到了17.11%。表明系统中氮的去除是由异养反硝化、氢自养反硝化和硫自养反硝化共同作用的结果,既有效减少了脱氮过程中有机碳源的消耗,又维持了系统酸碱度的平衡,从而能够在低碳氮比条件下维持稳定高效的脱氮效果。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.