BAF处理生活污水过程中同步去除H2S的试验研究

采用曝气生物滤池处理生活污水的过程中,以混和臭气的空气为气源,以掺入了陶粒和铁炭颗粒的复合填料为载体,研究了反应器的运行条件和参数,结果表明,以混合臭气的空气作为气源对污水处理过程的需氧量基本无影响。当反应器的进气量为40 L/h,进水容积负荷和进气H2S的浓度分别在0.3～1.6 kg COD/(m³·d)和0.8～2.3 mg/m³之间变化时,可以实现出气和出水中H₂S和COD分别小于0.04 mg/m³和90 mg/L,满足同时达标排放的要求。H₂S的同步去除可能是通过微生物的氧化分解和形成FeS沉淀来实现的。     

改进型生物滴滤塔处理H2S臭气的最适工艺条件研究

以H2S气体为研究对象,考察改进型生物滴滤塔的脱臭效能、最适工艺运行条件及其影响因素.试验结果表明,循环液喷淋量为10 L/s,气体流量为400 L/s的情况下,最高H2S负荷率可以达到68.2 g/m3·h;最适气体停留时间68.4 s.当入口H2S浓度分别为0～700 mg/m3、700～1000 mg/m3和大于1000 mg/m3时,对应的最适循环液喷淋量为10 L/s、15 L/s和60 L/s.H2S去除率100%的情况下,最大允许进气浓度可达1870 mg/m3,即最大H2S负荷率为98.4 g/m3·h.该研究表明,改进型生物滴滤塔具有较高的H2S去除能力,最适工艺运行条件的确定对污水厂臭气和化工行业产生的H2S处理具有一定的指导意义.     

矿化污泥生物反应器处理生活垃圾填埋场老龄渗滤液

经长时间稳定化形成的矿化污泥中,含有种类丰富和数量繁多的降解性微生物,具有处理渗滤液的潜力。建立3个矿化污泥生物反应器,即C1(粉煤灰0%),C2(粉煤灰9.1%),C3(粉煤灰16.7%),以处理垃圾填埋场老龄渗滤液。在单级矿化污泥反应器中,当进水COD和NH3-N分别约为1350和900 mg/L时,水力负荷为17.7～70.8 L/(m3.d),COD去除率可超过65%,氨氮的去除率可超过94%。粉煤灰的加入一定程度上降低了COD去除率,但有助于氨氮的去除。在二级矿化污泥生物反应器中(即C3～C1串联),水力负荷为35.4 L/(m3.d)的工况下,当COD、TOC、IC和NH3-N分别为1 500～2 500,500～900,1 200～1 600和1 200～1 450 mg/L时,出水可达到COD<300 mg/L,TOC<180 mg/L,IC<100 mg/L,NH3-N<5 mg/L。但是,矿化污泥生物反应器对渗滤液总氮的去除率较低,仅为20%左右。     

升流式厌氧污泥床反应器工程启动研究

论述生产性 UASB反应器 ,在中温条件下处理玉米淀粉废水的启动过程 ,讨论了运行和颗粒污泥形成过程及影响因素 ;反应器稳定运行时 ,进水 COD在 60 0 0～ 80 0 0 mg/L ,容积负荷可达 6～ 10 kg COD/( m3· d) ,出水 COD降至 2 0 0～ 45 0 mg/L。     

曝气生物滤池去除有机物及硝化氨氮的影响因素研究

采用以陶粒为填料的曝气生物滤池(BAF)处理低浓度生活污水,研究在气水比一定的条件下,水力负荷、有机负荷及氨氮负荷对BAF去除有机物及硝化氨氮的性能的影响.研究结果表明,当试验进水COD为105.8～156.6 mg/L,气水比为3:1的条件下,降解有机物的最佳水力负荷为1.35～1.68 m3/(m2·h),COD平均去除率为86.3%.氨氮负荷是影响反应器硝化性能的直接因素.当水力负荷为1.05 m3/(m2·h),平均进水COD为106.1 mg/L时,若使出水氨氮低于15 mg/L,则反应器能承受的最大进水氨氮负荷为0.5 kg/(m3·d)左右.并确立了相应的反应器动力学模型.     

大型UASB处理阿维菌素废水厌氧污泥颗粒化研究

采用大型UASB反应器处理阿维菌素废水,接种好氧絮状污泥,经过189 d运行,成功实现了厌氧污泥颗粒化.通过调节反应器进水水质控制进水中阿维菌素浓度和长时间培养驯化,阿维菌素对厌氧消化的抑制影响基本消除.UASB反应器进水pH值4～5、COD 8890～12 100 mg/L、容积负荷达到10.5 kg COD/m3·d,COD去除率稳定在85%以上,出水COD为1308～1670 mg/L.     

HRT对固定床厌氧反应器运行效果的影响

为了考察水力停留时间(HRT)对炭纤维载体固定床厌氧反应器运行效果的影响,在进水COD分别为20 000~25 000 mg/L和40 000~45 000 mg/L2个浓度范围下,研究了不同HRT对反应器运行效果的影响。结果表明,通过HRT的调整,在达到相同有机负荷(OLR)下,进水COD为20 000~25 000 mg/L的COD去除率和产气量,明显比进水COD为40 000~45 000 mg/L的运行效果好;进水COD为20 000~25 000 mg/L,HRT为14 h,相应的OLR为41.09 kgCOD/(m3.d)时,COD去除率仍然维持在68%以上,沼气容积产气率达到14.55 m3/(m3.d)。炭纤维载体固定床厌氧反应器具有较高的COD去除率、产气效率以及抵抗低pH、高负荷冲击的能力,运行过程中没有发生反应器堵塞的现象。     

低COD浓度废水启动EGSB反应器

以厌氧活性污泥和好氧活性污泥接种于2个膨胀颗粒污泥床(EGSB)反应器中,进水流量为10 mL/min,回流量为180 mL/min,进水COD浓度在180 mg/L左右,有机负荷率(OLR)为1.728 kg COD/m3·d左右,污泥负荷率(SLR)为0.19 kg COD/kg MLSS·d左右,出水COD浓度维持在40mg/L左右,COD去除率达80%以上.控制温度在32～35 ℃,pH在6.8～7.2,反应器内氧化还原电位在-340 mV以下,水力停留时间(HRT)4.2 h,上升流速4.86 m/h以及加入80 mg/L絮凝剂(硫酸铝钾),缩短了启动时间,促进了颗粒污泥的形成.分别经过60 d和120 d运行,反应器启动成功.结果表明,上升流速、絮凝剂和污泥类型对颗粒污泥的形成有影响;接种好氧活性污泥在低浓度COD下,合理控制负荷速率能成功启动EGSB反应器.     

多层生物滤塔净化硫化氢废气研究

以木屑为填料,采用多层生物滤塔净化H2S气体,研究其适宜的工艺条件及生物降解宏观动力学.结果表明,填料分层可提高H2S去除率,当进气容积负荷＜153.2 g H2S/(m3·d)时,H2S的去除率保持在90%以上;进气浓度低于70 mg/m3,下层200mm填料对H2S总去除率的贡献在50%以上;填料含水率为50%～6...     

生物滴滤塔处理H_2S臭气

目前,环保政策极其关注污水处理厂的臭气排放并制定了排放标准。本实验依托3个并联的中试生物滴滤塔对污水提升泵站的H2S臭气展开研究,考察不同H2S进气负荷、停留时间、压降和填料填装方式(竹炭-陶粒分层填装、完全混合及全竹炭填装)等因素对H2S去除率的影响。对生物滴滤塔的出气浓度、滤出液p H、SO2-4离子等进行测试分析,建立传质、降解动力学模型,并分析。在停留时间为25 s连续进气条件下,考察进气负荷在0.59~5.00 g H2S/(m3·h)范围内生物滴滤塔对H2S臭气的去除表现效果。研究结果表明,各生物滴滤塔的去除率(RE)都维持在98%以上,而且出气浓度达到厂界废气排放三级标准;相较于完全混合填装方式,分层填装在去除H2S臭气时略显优势。采用Michaelis-Menten方程描述生物滴滤塔的去除表现,表观半饱和常数Ks和最大表观去除速率Vm分别为5.92 m L/m3和5.84 g H2S/(m3·h)。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.