Pt颗粒尺寸对Pt/CeO2催化氧化甲苯性能影响

使用乙二醇还原法制备了一系列不同尺寸的Pt-x纳米颗粒(x=1.41、1.57、1.79、1.95、2.12、2.32 nm),将其负载于棒状(rod)CeO_2载体上.考察了不同尺寸的Pt颗粒催化剂Pt-x/CeO_2-rod在甲苯催化氧化反应中的催化性能.结果显示,随着Pt颗粒尺寸的增加,催化剂活性先升高后降低.其中,Pt颗粒尺寸为1.79 nm时催化剂催化活性最好,T90=133℃.一般认为,Pt颗粒尺寸增加其分散度减小,导致催化活性降低.然而本实验结果表明,随Pt尺寸增加催化活性先升高后降低,并且基于催化剂表面Pt原子计算的TOFs(turnover frequencies)随Pt尺寸增加逐渐变大.紫外拉曼光谱(UV Raman)、XRD、XPS显示,随着Pt颗粒尺寸增加,催化剂Pt-x/Ce-rod表面氧空位的浓度逐渐增加.氧空位有效提高了催化剂晶格氧的流动,促进了氧气的吸附活化及传递过程.Pt/Ce催化剂催化氧化甲苯反应活性是Pt分散度以及CeO_2表面氧空位浓度双重作用的结果.     

Pt颗粒负载对CeO2臭氧催化氧化甲苯的增强作用

通过铂颗粒吸附法制备得到Pt/CeO₂催化剂应用于臭氧催化氧化甲苯反应,研究了Pt颗粒负载对CeO₂臭氧催化氧化甲苯的增强作用.采用氢气程序升温还原（H₂-TPR）、氧气程序升温脱附（O₂-TPD）、X射线光电子能谱（XPS）和拉曼光谱（Raman）等手段对催化剂进行表征,结果显示,CeO₂负载Pt颗粒后,Pt与CeO₂存在相互作用,提高了CeO₂上氧空位的含量.臭氧分解实验证实了Pt/CeO₂催化剂具有更好的臭氧分解性能.臭氧催化氧化甲苯评价结果表明,Pt/CeO₂具有比CeO₂更优异的催化性能,在80 ℃时甲苯降解率、CO₂产率和臭氧分解率分别达到92.3%、92.1%和99.9%.原位拉曼进一步研究了臭氧分解生成的氧物种种类及含量,以及甲苯存在时氧物种的变化,结果表明,臭氧在氧空位上分解产生的过氧物种较为稳定,是氧化甲苯的重要活性物质.因此,Pt颗粒负载在CeO₂上能增强臭氧在催化剂上分解,并形成更多过氧物种,最终提升臭氧催化氧化甲苯的性能.     

改性赤泥负载Pt催化剂催化氧化甲苯的性能

以改性赤泥为载体,采用浸渍方法制备低成本改性赤泥(MRM)负载Pt催化剂,并探究Pt含量对Pt/MRM催化剂催化氧化甲苯活性影响.结果表明0.4Pt/MRM表现出最佳的催化活性,在230℃时甲苯转化率为100%.当空速高达120000h^-1时0.4Pt/MRM催化剂依然能保持着较高的催化活性.当甲苯进口浓度为5000mg/m³时仍可以有效氧化甲苯.采用XRD、FT-IR、BET、H₂-TPR和O₂-TPD等手段进行表征测试分析发现,MRM的比表面积较RM大幅度提高,使MRM能够更好分散活性组分Pt,成为合适的活性组分Pt的催化剂载体.同时所制备的x Pt/MRM催化剂具有较高的比表面积和良好的孔结构.改性赤泥中Fe₂O₃与活性组分Pt物种相互作用,使催化剂的总氧解吸量增大,提高了催化剂表面氧的迁移率,从而提高了催化效率.     

聚合物辅助成型法制备纳米Co3O4/CeO2催化剂及其对CO低温氧化性能研究

采用聚合物辅助成型法,以乙二胺四乙酸(EDTA)和聚乙烯亚胺(PEI)为配位体制备了Co_3O_4/CeO_2催化剂,对其进行了氮气吸附、XRD、XPS、SEM、TEM、H2-TPR和CO-TPR等表征,并考察了材料的CO低温催化性能.结果表明,采用聚合物辅助成型法能够合成出具有三维空间网络结构的纳米Co_3O_4/CeO_2催化剂,Ce的加入有利于获得具有更小尺寸的Co_3O_4颗粒,并提高Co3+的相对含量,从而有利于CO低温催化性能的提高;Ce/Co的摩尔比为1时,样品具有最佳的CO催化性能,在催化温度为30℃时,可使初始浓度为100 ppm的CO完全转化;同时,纯氧气加热吹扫有利于催化剂的稳定再生.本研究可为CO低温催化剂的制备提供重要参考.     

Fe3O4/CeO2-H2O2非均相类Fenton体系下降解TCE的研究

采用浸渍法成功合成了新型催化剂纳米Fe3O4/CeO_2,并且用Fe3O4/CeO_2-H_2O_2非均相Fenton体系对TCE进行降解研究,考察了初始pH、H_2O_2浓度、温度及催化剂投加量等因素对于TCE降解效率的影响.实验结果表明,Fe3O4/CeO_2-H_2O_2非均相Fenton体系对TCE具有较好的去除效果:在初始pH=3,温度50℃,H_2O_2浓度30 mmol·L-1和Fe3O4/CeO_2投加量0.5 mg·L-1时,TCE去除率高达97.29%.同时实验结果表明pH在2~7范围内对TCE均有降解效果,所以相对于传统Fenton体系,该体系拥有更宽pH应用范围.目标污染物的降解符合一级动力学,反应活化能为30.77 k J·mol-1,表明反应易于进行.     

MCM-41孔径对负载MnOx催化氧化甲苯性能的影响

以3种不同孔径的介孔分子筛MCM-41（2.66、4.24和4.64 nm）为载体,采用等体积浸渍法制备MnO_x/MCM-41,考察了其催化氧化甲苯的活性,并用XRD、TEM、H₂-TPR、O₂-TPD和XPS等手段对催化剂进行表征.结果表明,增大载体孔径改变了锰元素的价态分布,提高了Mn³⁺和表面吸附氧的含量,使得催化剂的氧化还原性和晶格氧流动性也有所提升.因此,载体孔径从2.66 nm增大至4.64 nm后,MnO_x/MCM-41催化氧化甲苯的T90(体积空速=21200 h^-1)从369℃降至335℃.此外,还利用FTIR分析了甲苯的降解途径：甲苯先被活化脱氢,形成苯甲基,被吸附于催化剂表面;然后苯甲基被氧化为苯甲醇、苯甲醛和苯甲酸,随后苯环被破坏,苯甲酸裂解为马来酸、羧酸和甲酸等物质;最后被完全氧化为水和二氧化碳.     

OMS-2负载Pt催化剂的制备及其催化氧化性能研究

采用前掺杂法、沉积-沉淀法和浸渍法制备了氧化锰八面体分子筛(OMS-2)负载Pt催化剂(Pt/OMS-2),对所制催化剂进行了结构和织构表征。并研究了不同制备方法和沉积-沉淀法中不同制备(Pt负载量和溶液的pH值)对Pt/OMS-2催化氧化CO性能的影响。结果表明,沉积-沉淀法制备的Pt/OMS-2-DP催化剂活性最好(T100=100℃)。这与Pt/OMS-2-DP催化剂中Pt颗粒大小及OMS-2载体与Pt之间存在强相互作用有关。Pt负载量明显影响Pt/OMS-2-DP催化剂的催化活性,3Pt/OMS-2-DP催化剂(Pt=3.0 wt%)催化活性最高,这是由于适当Pt负载量,Pt颗粒较小,并与载体OMS-2的相互作用较强,能较好地活化OMS-2晶格氧。pH值对Pt/OMS-2-DP催化剂催化性能影响较大,这与OMS-2的等电点和Pt在不同溶液中存在不同Pt配位体形式有关。     

等离子体场内CeO2催化降解甲醇的表面活性氧物种来源与作用研究

利用水热法制备了3种不同形貌(纳米棒、纳米颗粒、纳米立方体)的CeO_2催化剂,并通过比表面积测试(BET)、扫描电子显微镜(SEM)、拉曼光谱分析(Raman)、O_2程序升温脱附(O_2-TPD)手段表征其物理化学性质,结果发现,CeO_2纳米棒的表面氧空位和氧物种最多.等离子体与催化协同降解甲醇性能评价实验结果显示,CeO_2纳米棒展现出最好的催化性能.进一步设计实验(甲醇-TPD、不同气氛常温催化、催化剂内后置比较、O_3催化氧化)推测在等离子体场内CeO_2表面活性氧物种来源及其作用.结果表明:①在等离子体场内参与CeO_2表面催化反应的活性氧物种有两个来源,一是催化剂本身存在的表面氧物种,二是等离子体区域产生的短寿命物种及长寿命物种(主要是O_3),其中,O_3分解产生的活性氧物种是提高催化性能的主要因素.②不同形貌CeO_2由于表面氧空位含量不同,导致O_3在催化剂上分解产生的活性氧物种的量不同,最终影响等离子体催化性能.     

甲烷催化还原NOx中Co基/分子筛催化剂的助剂和载体优化

采用共浸渍法制备了系列Co基/分子筛催化剂,在固定床催化反应器中考察了不同催化剂在甲烷催化还原NO_x中的催化行为,优化了Co基/分子筛催化剂的助剂和载体,并通过催化表征手段阐明了其构效关系.结果表明,Fe和SAPO-34分别作为优化助剂和载体制备得到的Co-Fe/SAPO-34催化剂具有最高的催化活性,在450℃时,NO_x的最大转化率可以达到52.7%.CO_2对Co-Fe/分子筛催化剂活性无明显抑制作用,H_2O对催化剂的活性抑制是可逆的,SO_2对催化剂活性抑制作用明显.Co-Fe/SAPO-34催化剂表面钴物种以CoO和Co(OH)_2为主,Co-Fe/ZSM-5催化剂表面钴物种则以Co_3O_4和Co(OH)_2为主,Co-Fe/Beta催化剂则可能以CoO、Co Al2O_4和Co_3O_4为主.各Co-Fe/分子筛催化剂表面Fe~(2+)/Fe~(3+)含量比依次为Co-Fe/ZSM-5(3.98)Co-Fe/SAPO-34(0.52)Co-Fe/Beta(0.43).活性组分钴物种的形态和合适的Fe~(2+)/Fe~(3+)含量比对Co-Fe/分子筛催化剂上甲烷催化还原NO_x至关重要.Co-Fe/分子筛催化剂上CH_4-SCR反应机制为:NO在Br?nsted酸位上吸附氧化成NO~+,同时CH_4在Br?nsted酸位上吸附活化成—C=O和—COO等活性物种,生成的NO~+在Co2+和Fe~(3+)等催化活性位上转化成硝酸盐等中间产物,中间产物硝酸盐与活化物种(—C=O和—COO)反应生成N_2和CO_2.     

添加铈对Cu-Co-O催化剂催化燃烧VOCs性能影响

以γ-Al_2O_3为载体,采用超声-等体积浸渍法制备CeO_2掺杂的Cu-Co-O/Al_2O_3催化剂,考察了催化剂对甲苯的催化燃烧性能,通过X线衍射(XRD)、程序升温还原(H_2-TPR)和扫描电子显微镜(SEM)等技术对催化剂进行表征.结果表明:稀土元素的加入不仅有利于活性组分在催化剂表面的分散,而且可以促进Cu-Co-O催化剂的还原温度向着低温方向发生移动.活性评价实验结果显示,进气浓度对催化剂催化活性的影响不大.添加Ce后催化剂对甲苯和二甲苯的催化燃烧反应温度均有不同幅度降低,其中对甲苯的效果更为显著.     

Effect of Ce doping of TiO2 support on NH3-SCR activity over V2O5-WO3/CeO2-TiO2 catalyst

CeO2–TiO2composite supports with different Ce/Ti molar ratios were prepared by a homogeneous precipitation method, and V2O5–WO3/CeO2–TiO2catalysts for the selective catalytic reduction（SCR） of NOx with NH3 were prepared by an incipient-wetness impregnation method. These catalysts were characterized by means of BET, XRD, UV–Vis,Raman and XPS techniques. The results showed that the catalytic activity of V2O5–WO3/TiO2 was greatly enhanced by Ce doping（molar ratio of Ce/Ti = 1/10） in the TiO2 support.The catalysts that were predominantly anatase TiO2 showed better catalytic performance than the catalysts that were predominantly fluorite CeO2. The Ce additive could enhance the surface adsorbed oxygen and accelerate the SCR reaction. The effects of O2 concentration, ratio of NH3/NO, space velocity and SO2 on the catalytic activity were also investigated. The presence of oxygen played an important role in NO reduction. The optimal ratio of NH3/NO was 1/1 and the catalyst had good resistance to SO2 poisoning.     

Effect of CeO2 and Al2O3 on the activity of Pd/Co_3O_4/cordierite catalyst in the three-way catalysis reactions (CO/NO/CnHm)

The present article studies the effect of CeO₂ and Al₂O₃ on the activity of Pd/Co₃O₄/cordierite catalyst in conversion of NO, CO, C_nH_m. The catalysts were characterized by temperature programmed reduction with hydrogen, X-ray diffraction, X-ray photoelectron spectroscopy and transmission electron microscopy. It is shown that the effect of CeO₂ on the properties of Pd/Co₃O₄/cordierite catalyst depends on preparation method. The catalyst obtained by co-deposition of cerium and cobalt oxides has higher activity in CO oxidation (CO + O₂ and CO + NO) and total hexane oxidation (C₆H₁₄ + O₂). Such phenomenon is probably caused by more than stoichiometric amount of formed oxygen vacancies, an increase in both mobility of surface oxygen and dispersity of components in the catalytic composition. It is demonstrated that CeO₂ addition promotes the SO₂ resistance of Pd/Co₃O₄/cordierite. The second support decreases the activity of Pd/Co₃O₄/cordierite catalyst in the reactions of CO and C₆H₁₄ with oxygen because of CoAl₂O₄ formation.     

Effect of pretreatment on Pd/Al2O3 catalyst for catalytic oxidation of o-xylene at low temperature

The effect of pretreatment on Pd/Al₂O₃ catalysts for the catalytic oxidation of o-xylene at low temperature was studied by changing the pretreatment and testing conditions. The fresh and pretreated Pd/Al₂O₃ catalysts were characterized by transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results showed that the pretreatment dramatically changed the Pd/PdO ratio and then significantly affected the Pd/Al₂O₃ activity; while the pretreatment had not much influence on Pd particle size. The Pd/Al₂O₃ pre-reduced at 300℃/400℃, which has fully reduced Pd species, showed the highest activity; while the fresh Pd/Al₂O₃, which has fully oxidized Pd species, presented the worst performance, indicating the Pd chemical state plays an important role in the catalytic activity for the o-xylene oxidation. It is concluded that metallic Pd is the active species on the Pd/Al₂O₃ catalyst for the catalytic oxidation of o-xylene at low temperature.     

N/Ce doped graphene supported Pt nanoparticles for the catalytic oxidation of formaldehyde at room temperature

Pt catalysts with nitrogen-doped graphene oxide (GO) as support and CeO₂ as promoter were prepared by impregnation method,and their catalytic oxidation of formaldehyde (HCHO) at room temperature was tested.The Pt-CeO₂/N-rGO (reduced GO) with a mass fraction of 0.7% Pt and 0.8%CeO₂ exhibited an excellent catalytic performance with the 100% conversion of HCHO at room temperature.Physicochemical characterization demonstrated that nitrogendoping greatly increased the...     

Characterization and performance of Pt/SBA-15 for low-temperature SCR of NO by C3H6

Pt supported on mesoporous silica SBA-15 was investigated as a catalyst for low temperature selective catalytic reduction(SCR) of NO by C 3 H 6 in the presence of excess oxygen.The prepared catalysts were characterized by means of XRD,BET surface area,TEM,NO-TPD,NO/C 3 H 6-TPO,NH 3-TPD,XPS and 27 Al MAS NMR.The effects of Pt loading amount,O 2 /C 3 H 6 concentration,and incorporation of Al into SBA-15 have been studied.It was found that the removal efficiency increased significantly after Pt loading,but an optimal loading amount was observed.In particular,under an atmosphere of 150 ppm NO,150 ppm C 3 H 6,and 18 vol.% O 2,0.5% Pt/SBA-15 showed remarkably high catalytic performance giving 80.1% NOx reduction and 87.04% C 3 H 6 conversion simultaneously at 140°C.The enhanced SCR activity of Pt/SBA-15 is associated with its outstanding oxidation activities of NO to NO 2 and C 3 H 6 to CO 2 in low temperature range.The research results also suggested that higher concentration of O 2 and higher concentration of C 3 H 6 favored NO removal.The incorporation of Al into SBA-15 improved catalytic performance,which could be ascribed to the enhancement of catalyst surface acidity caused by tetrahedrally coordinated AlO 4.Moreover,the catalysts could be easily reused and possessed good stability.     

Effects of Ce on catalytic combustion of methane over Pd-Pt/Al2O3 catalyst

Activity and stability of 1%Pd-0.2%Pt/Al₂O₃ and 1%Pd-0.2%Pt/0.6%Ce/Al₂O₃ catalysts prepared by impregnation method for catalytic combustion of methane in air were investigated. The catalysts before and after reaction were characterized by BET, CO chemisorption, XRD and XPS techniques. Results showed that the presence of Ce significantly increased the activity and thermal stability of the Pd-Pt/Al₂O₃ catalyst towards methane combustion, which could be attributed to more highly-dispersed active PdO particles over the Pd-Pt/Ce/Al₂O₃ catalyst surface as well as the retarded sintering of PdO and the maintained oxidized state of surface Pd during the combustion process in the presence of Ce.     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

Size effect of Pt nanoparticles in acid-assisted soot oxidation in the presence of NO

Pt/Al₂O₃ catalysts with mean Pt particle size ranged from 2.7 to 7.1 nm were synthesized by chemical reduction method, and the sulfated counterparts were prepared by impregnation of sulfuric acid. The turnover frequency of platinum for soot oxidation under loose contact conditions in a feed flow containing NO and O₂ are positively correlated with the size of platinum. The sulfated Pt/Al₂O₃ exhibits higher catalytic activity for soot oxidation in the presence of NO despite their reduced ability for NO₂ production. Such a contradiction is more significant for those catalysts with smaller platinum particles. Herein, the catalysts were characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), transmission electron microscopy (TEM), inductive coupled plasma (ICP) emission spectrometry, CO chemisorption, thermogravimetric analysis (TGA), NH₃ temperature-programmed desorption (NH₃-TPD), NO temperature-programmed oxidation (TPO) and NO_x temperature-programmed desorption (TPD). Possible effect of Pt particle size for the catalytic oxidation of soot in the presence of NO was presented based primarily on the promoted NO₂ transfer efficiency onto the soot pushed by the acidic catalysts.     

CuO对贵金属/CeO2/Al2O3催化剂的作用

制备含少量贵金属Ｐｔ、Ｐｄ的不同Ｃｕ和Ｃｅ摩尔含量比（０：１０,１：９,２：８）的催化剂,实验条件十加入ＣｕＯ可以提高Ｐｔ催化剂的二效活性;加入Ｃｕ：Ｃｅ＝２：８的ＣｕＯ降低了Ｐｄ催化剂的顾效性能,然而Ｃｕ：Ｃｅ＝１：９时可以改善Ｐｄ催化剂的三效催化性能。通过结构分析,认为ＣｕＯ的存在可以提高ｄ催化剂的比表面积,ＰｄＯ的分散度。