壳聚糖絮凝剂对聚合氯化铝的助凝作用

以壳聚糖絮凝剂作为聚合氯化铝(PAC)的助凝剂,絮凝处理颐和园昆明湖湖水,考察了PAC在壳聚糖助凝作用下对浊度和有机物的去除效果,以及水中残留铝浓度的变化．结果表明,壳聚糖对PAC的助凝作用显著,PAC中加入壳聚糖絮凝剂后,浊度和有机物去除率均明显提高．     

壳聚糖复合絮凝剂在城市生活污水处理中的应用

研究了壳聚糖复合絮凝剂在不同来源的城市生活污水处理中的应用 ,确定了壳聚糖复合絮凝剂在城市生活污水处理中的最佳投加量 ,即 :最佳投加量 (mg·l- 1)∶原水COD (mg·l- 1) =1∶8 2— 8 7和最佳pH =7;它与传统的絮凝剂PAC同比 ,COD去除率提高 7— 1 3% ,SS去除率提高 3— 1 0 % ,[Al3 + ]下降 6 1— 85 % ,药剂加量减少76— 82 % .     

Al13去除水中腐殖酸的混凝作用机理

研究对比了Al13、不同碱化度的聚合氯化铝(PACl)及工业聚合氯化铝等去除水中腐殖酸的絮凝特征,从Zeta电位、RT(余浊)、UV254等角度分别考察了pH值和投药量的影响,对不同形态组成絮凝剂的混凝效能有了进一步明确的认识,并且对Al13的絮凝机理进行了有益的探索．结果表明,Al13是混凝过程中的优势形态,决定着混凝剂的电中和能力．     

海泡石、膨润土改性壳聚糖对景观水絮凝效果的研究

壳聚糖及海泡石、膨润土均是纯天然、无害物质,利用海泡石、膨润土等粘土改性壳聚糖制备生态絮凝剂是絮凝剂发展的重要方向,将其应用于景观水的治理,可以有效地改善景观水的观赏性.以苏州艺圃园林景观水为例,研究了两种改性絮凝剂的絮凝效果.苏州艺圃园林景观水内藻类以绿藻Chlorphyta为主,鉴于景观水的特殊观赏性,以浊度大小设定正交试验,得出了投放量、配比、醋酸用量、搅拌时间的最优值.试验证明海泡石、膨润土均对壳聚糖絮凝产生矾花的密实度和分形维数[1]有明显的增强效果,膨润土效果略好,克服了壳聚糖分子量较小、吸附架桥能力差、矾花不够密实的缺点.在最优条件下,这两种改性后的絮凝剂可使水样浊度降至5 NTU以下,叶绿素a的去除率达93％以上,明显好于单独使用壳聚糖絮凝剂的情况.随原水浊度的增加,浊度去除率缓慢减小,pH值在7.5～8.5之间浊度去除率最高,温度对絮凝效果影响不大.试验表明壳聚糖及海泡石、膨润土两种改性絮凝剂对景观水的治理和生态絮凝剂的制备具有指导意义.     

壳聚糖/膨润土复合絮凝剂处理染料废水的研究

利用壳聚糖/钠基膨润土复合絮凝剂对活性艳红X3B等11种染料模拟废水及实际印染废水进行絮凝脱色处理。考察了复合絮凝剂投加量、pH值、搅拌速率、搅拌时间等因素对模拟染料废水絮凝脱色的影响。结果表明,在染料浓度为100 mg.L-1,pH为5的条件下,复合絮凝剂投加量为1.25 g.L-1时,3种质量比的复合絮凝剂对活性艳红X3B的脱色率分别达到75%、90%和97%以上;质量比为1∶10的壳聚糖/钠基膨润土复合絮凝剂,对其它活性、还原性、分散性、水溶性等8种印染厂常用染料也具有很好的絮凝脱色作用,脱色率均可达94%以上。对印染废水处理厂进水口废水和经过A/O处理后废水的色度去除率和COD去除率分别可以达到81.05%、83.74%和53.21%、41.22%,具有一定的应用前景。     

活性污泥生物絮凝剂絮凝效果研究

为充分利用剩余污泥,利用碱法从污水处理厂二沉池取回的沉降污泥提取生物絮凝剂,以浊度及COD去除率参考,通过生物絮凝剂的投加量(A)、搅拌速度(B)、搅拌时间(C)、污泥浓度(D)4个因素进行正交试验,结果表明:浊度去除试验中,正交表最大去除率63.21%,最佳组合A2B1C3D1浊度去除率可达66.71%,COD去除率为61.13%;COD去除试验中,正交表最大去除率71.20%,最佳组合A3B3C2D3COD去除率可达75.57%,浊度去除率为60.48%.说明活性污泥提取生物絮凝剂具有较理想的絮凝效果,可以推广应用.     

钽铌冶炼铁泥制备聚硅酸硫酸铁絮凝剂及其应用

本文以Fenton试剂法处理钽铌冶炼废水产生铁泥作为聚硅酸硫酸铁制备铁源,在不同的ω(SiO_2)、pH值、n(Fe)/n(Si)条件下优化制备了聚硅酸硫酸铁絮凝剂,并进行钨铋多金属矿选矿废水及高浊度模拟废水处理.研究结果表明:在ω(SiO_2)=1.00%、pH=3.00、n(Fe)∶n(Si)=1∶1的适宜条件下制得的聚硅酸硫酸铁絮凝剂效果最佳.在0.10%(体积分数)投加量下搅拌2 min,钨铋选矿废水浊度去除率达99.9%,COD去除率达76.8%,废水中Pb和As去除率分别达98.8%和97.2%,Be去除率几乎达100%,处理后废水浊度由319 NTU降至0.32 NTU、COD含量由322 mg·L~(-1)降至74.7 mg·L~(-1),废水中Pb和As质量浓度分别由7.89、1.03 mg·L-1降至0.09、0.03 mg·L~(-1),未检出Be;高浊度模拟废水浊度去除率达98.5%,浊度由716 NTU降至10.7 NTU.处理后废水达到《污水综合排放标准》(GB 8979—1996)一级标准.     

稀土镧改性聚合硫酸铁机理分析及其应用

为进一步提高无机高分子絮凝剂的处理效果并降低处理成本,研究"一步法"絮凝剂制备工艺,同时引入稀土镧对絮凝剂进行改性处理,制备固体稀土镧聚合硫酸铁絮凝剂(La-PFS).实验通过响应面优化絮凝性能,研究结果表明.聚合温度为123℃、镧铁摩尔比为1∶105.56、OH~-/Fe摩尔比为0.19时,制备产品对高浊度废水除浊效率效果达到99.41%.引入稀土镧在一定程度上增长絮凝剂链状结构,增强吸附能力.在对造纸废水处理中,稀土镧聚合硫酸铁对造纸废水处理效果明显优于传统市售絮凝剂,絮凝沉淀速度有较大提升,浊度去除率达到68%,COD_(Cr)去除率达到35%.     

阳离子化克雷伯氏菌絮凝剂CMBF-NⅢ2在生活污水中的应用

微生物絮凝剂具有无毒性,绿色生产等优点,能够安全地用于给水处理及污废水处理.本文通过阳离子改性和与非生物絮凝剂复配的方法,提高MBF-NIII2的絮凝能力.以MBF-NIII2为原料,利用3-氯-2-羟丙基三甲基氯化铵(CHTAC)对其修饰,合成新型阳离子化的微生物絮凝剂(CMBF-NIII2)以CMBF-NIII2为研究主要对象,对校园生活污水进行处理.通过改变投加量、pH值、沉淀时间与温度,探究CMBF-NIII2絮凝能力的变化规律.将改性前的MBF-NIII2与改性后的CMBF-NIII2分别用于校园生活废水的处理,对比发现当CMBF-NIII2投加量为1.3 mL,pH 4.6,温度为60℃,沉降时间为40 min时,絮凝率达到91.5%,且COD去除率为87.8%,絮凝能力明显优于MBF-NIII2(絮凝率为47.61%),能更高效地絮凝生活污水.以MBF-NIII2与三氯化铁复配处理生活污水,结果表明MBF-NIII2和FeCl_3的投加量分别为10 mg·L~(-1)和15 mg·L~(-1)时,絮凝率可达88.06%,不仅比单独使用MBF-NIII2的处理效果好,还相对减少了絮凝剂的投加量.     

环氧氯丙烷-二甲胺聚合物和聚合氯化铝用于印染废水的处理

用不同碱化度(B)的聚合氯化铝(PAC)和不同粘度(η)的环氧氯丙烷-二甲胺聚合物(EPI-DMA)以及PAC-EPI-DMA复合絮凝剂处理印染废水.考察了药品投量,投加方式对脱色效果的影响.探讨了PAC的B值及EPI-DMA的η值对PAC-EPI-DMA絮凝性能的影响.结果表明,PAC-EPI-DMA复合絮凝剂较PAC和EPI-DMA絮凝剂具有较低的投加量和较好的脱色效果;B=1.5,η=1600的PAC-EPI-DMA具有较好的脱色效果和COD去除率,当废水的pH=4-7时处理效果较好.     

微波－混凝法处理滇池高藻原水的实验研究

实验采用微波－混凝法处理滇池高藻原水,考察了混凝剂聚合氯化铝（PAC）投加量、进水pH值、微波功率及辐照时间对除藻去浊效果的影响,并与单一混凝的处理效果进行了对比。结果表明：在PAC投加量为80mg／L、进水pH值为8—9、微波功率为600W、辐照时间为1．5min的条件下除藻去浊效果最佳,除藻率达94．4％,剩余浊度可从89NTU降到3NTU左右;微波－混凝法对滇池高藻原水的处理效果明显优于单一混凝,同时可降低混凝剂用量,具有良好的强化混凝效果。     

人工湿地系统对含沼液畜禽废水净化效果试验研究

为了考察人工湿地处理含沼液畜禽废水的可行性,采用水平潜流人工湿地对含沼液畜禽废水进行处理实验。试验结果表明：在进水流量1.5 m3.d-1,水平潜流人工湿地系统对含沼液畜禽废水具有较好的处理效果。废水中COD、TP、TN和NH4＋-N浊度平均去除率分别为59.21%、53.80%、55.09%和55.57%.另外,通过对人工湿地沿程的污染物变化试验分析表明,人工湿地系统对污染物的降解是沿人工湿地水流方向逐渐降低的。     

Optimization and modeling of coagulation-flocculation to remove algae and organic matter from surface water by response surface methodology

Charge neutralization and sweep flocculation were the major mechanisms. Effect of process parameters was investigated. Optimal coagulation conditions were studied by response surface methodology. ANN models presented more robust and accurate prediction than RSM. Seasonal algal blooms of Lake Yangcheng highlight the necessity to develop an effective and optimal water treatment process to enhance the removal of algae and dissolved organic matter (DOM). In the present study, the coagulation performance for the removal of algae, turbidity, dissolved organic carbon (DOC) and ultraviolet absorbance at 254 nm (UV₂₅₄) was investigated systematically by central composite design (CCD) using response surface methodology (RSM). The regression models were developed to illustrate the relationships between coagulation performance and experimental variables. Analysis of variance (ANOVA) was performed to test the significance of the response surface models. It can be concluded that the major mechanisms of coagulation to remove algae and DOM were charge neutralization and sweep flocculation at a pH range of 4.66–6.34. The optimal coagulation conditions with coagulant dosage of 7.57 mg Al/L, pH of 5.42 and initial algal cell density of 3.83 × 10⁶ cell/mL led to removal of 96.76%, 97.64%, 40.23% and 30.12% in term of cell density, turbidity, DOC and UV₂₅₄ absorbance, respectively, which were in good agreement with the validation experimental results. A comparison between the modeling results derived through both ANOVA and artificial neural networks (ANN) based on experimental data showed a high correlation coefficient, which indicated that the models were significant and fitted well with experimental results. The results proposed a valuable reference for the treatment of algae-laden surface water in practical application by the optimal coagulation-flocculation process.     

Surface water treatment benefits from the presence of algae: Influence of algae on the coagulation behavior of polytitanium chloride

• Emerging titanium coagulation was high-efficient for algae-laden water treatment. • Polytitanium coagulation was capable for both algae and organic matter removal. • Surface water purification was improved by around 30% due to algae inclusion. • Algae functioned as flocculant aid to assist polytitanium coagulation. • Algae could enhance charge neutralization capability of polytitanium coagulant. Titanium-based coagulation has proved to be effective for algae-laden micro-polluted water purification processes. However, the influence of algae inclusion in surface water treatment by titanium coagulation is barely reported. This study reports the influence of both Microcystis aeruginosa and Microcystis wesenbergii in surface water during polytitanium coagulation. Jar tests were performed to evaluate coagulation performance using both algae-free (controlled) and algae-laden water samples, and floc properties were studied using a laser diffraction particle size analyzer for online monitoring. Results show that polytitanium coagulation can be highly effective in algae separation, removing up to 98% from surface water. Additionally, the presence of algae enhanced organic matter removal by up to 30% compared to controlled water containing only organic matter. Polytitanium coagulation achieved significant removal of fluorescent organic materials and organic matter with a wide range of molecular weight distribution (693–4945 Da) even in the presence of algae species in surface water. The presence of algae cells and/or algal organic matter is likely to function as an additional coagulant or flocculation aid, assisting polytitanium coagulation through adsorption and bridging effects. Although the dominant coagulation mechanisms with polytitanium coagulant were influenced by the coagulant dosage and initial solution pH, algae species in surface water could enhance the charge neutralization capability of the polytitanium coagulant. Algae-rich flocs were also more prone to breakage with strength factors approximately 10% lower than those of algae-free flocs. Loose structure of the flocs will require careful handling of the flocs during coagulation-sedimentation-filtration processes.     

高效聚合氯化铝在石油化工污水回收处理中的应用

通过絮凝性能比较以及中试规模的应用，表明高效聚合氯化铝具有用量少，污泥少，除浊率高，对出水ｐＨ影响小等优点，是石油化工污水回用处理中的理想絮凝剂。     

Fenton——聚硅铝铁处理生活垃圾压滤液研究

为了降低生活垃圾压滤液污染负荷,为后续生化处理的正常运行创造良好条件,针对垃圾压滤液污染特性,以CODCr去除率为指标,通过正交实验和单因素实验研究了Fenton—聚硅铝铁混凝法处理城市生活垃圾压滤液的最优反应条件和处理效果。结果表明:采用该工艺处理垃圾压滤液时,pH值对CODCr去除率影响最大,其次是PSAF,再次是H2O2和FeSO4,在最优反应条件下,浊度去除率达到95.3%,CODCr去除率达到86.7%,BOD5去除率达到81.6%,浊度、CODCr、BOD5分别下降到86NTU、4201 mg.L-1、855 mg.L-1。     

高效絮凝反应器处理生活污水试验研究

本文采用高效絮凝模拟反应器进一步对实际生活污水进行连续运行处理试验，结果表明，直接絮凝沉淀处理后的出水浊度去除率和ＣＯＤ去除率分别达到９３．４％和７９．２％，可完全达到排放标准。絮凝处理后再经纤维过滤柱过滤处理，可控制出水浊度在１．０ＮＴＵ以下，ＣＯＤ去除率增加５．０￣７．０％，试验结果进一步验证了这种高效絮凝装置具有高效处理效能及实际工程应用推广价值。     

聚合氯化铝-高锰酸钾-羟基氧化铁复合强化混凝微污染原水

选用聚合氯化铝（PAC）与高锰酸钾、羟基氧化铁进行复配,强化混凝处理微污染原水。研究了复合混凝剂投加量、反应时间、进水pH、进水有机物浓度等对混凝效果的影响及絮体的沉淀性能。结果表明,PAC-KMnO4-β-FeOOH三元复合混凝剂具有显著的强化混凝效果,与相同条件下单投PAC及PAC-KMnO4二元复合混凝相比,TOC去除率分别提高了30%与20%。达到相同的浊度去除效果,三元复配混凝剂可缩短27%~50%的反应时间,减少65%~75%的沉淀时间。进水pH、有机物浓度在一定范围内变动时,PAC-KMnO4-β-FeOOH三元复合混凝剂对浊度与TOC的去除率均高于单投PAC的处理效果,三元复合混凝剂具有较强的抗水质变化冲击能力。     

Anaerobic degradation of coconut husk leachate using UASB-reactor

Reffing of coconut husk, the majorprocess in quality coir fibre extraction, causes serious pollution with brackish water lagoons of Kerala. An attempt is made to treat the coconut husk leachate by using a laboratory scale UASB-reactor The experiment was conducted with loading of leachate from 1 kg of fresh coconut husk. The anaerobic treatment was done continuously The parameters like VFA, pH, COD and polyphenols were analysed regularly during the evaluation of the reactor performance. The polyphenol, VFA and COD were diminished gradually with time. The pH of the reactor during the study was found to be in the range of 6-8. The biogas production was increased with loading and about 82% of the total COD/kg husk could be converted to biogas. The maximum polyphenol loading in the reactor was reached to about 298.51 mg/l of husk.