Enhanced cross-flow filtration with flat-sheet ceramic membranes by titanium-based coagulation for membrane fouling control

• Ceramic membrane filtration showed high performance for surface water treatment. • PTC pre-coagulation could enhance ceramic membrane filtration performance. • Ceramic membrane fouling was investigated by four varied mathematical models. • PTC pre-coagulation was high-effective for ceramic membrane fouling control. Application of ceramic membrane (CM) with outstanding characteristics, such as high flux and chemical-resistance, is inevitably restricted by membrane fouling. Coagulation was an economical and effective technology for membrane fouling control. This study investigated the filtration performance of ceramic membrane enhanced by the emerging titanium-based coagulant (polytitanium chloride, PTC). Particular attention was paid to the simulation of ceramic membrane fouling using four widely used mathematical models. Results show that filtration of the PTC-coagulated effluent using flat-sheet ceramic membrane achieved the removal of organic matter up to 78.0%. Permeate flux of ceramic membrane filtration reached 600 L/(m²·h), which was 10-fold higher than that observed with conventional polyaluminum chloride (PAC) case. For PTC, fouling of the ceramic membrane was attributed to the formation of cake layer, whereas for PAC, standard filtration/intermediate filtration (blocking of membrane pores) was also a key fouling mechanism. To sum up, cross-flow filtration with flat-sheet ceramic membranes could be significantly enhanced by titanium-based coagulation to produce both high-quality filtrate and high-permeation flux.     

Optimization and modeling of coagulation-flocculation to remove algae and organic matter from surface water by response surface methodology

Charge neutralization and sweep flocculation were the major mechanisms. Effect of process parameters was investigated. Optimal coagulation conditions were studied by response surface methodology. ANN models presented more robust and accurate prediction than RSM. Seasonal algal blooms of Lake Yangcheng highlight the necessity to develop an effective and optimal water treatment process to enhance the removal of algae and dissolved organic matter (DOM). In the present study, the coagulation performance for the removal of algae, turbidity, dissolved organic carbon (DOC) and ultraviolet absorbance at 254 nm (UV₂₅₄) was investigated systematically by central composite design (CCD) using response surface methodology (RSM). The regression models were developed to illustrate the relationships between coagulation performance and experimental variables. Analysis of variance (ANOVA) was performed to test the significance of the response surface models. It can be concluded that the major mechanisms of coagulation to remove algae and DOM were charge neutralization and sweep flocculation at a pH range of 4.66–6.34. The optimal coagulation conditions with coagulant dosage of 7.57 mg Al/L, pH of 5.42 and initial algal cell density of 3.83 × 10⁶ cell/mL led to removal of 96.76%, 97.64%, 40.23% and 30.12% in term of cell density, turbidity, DOC and UV₂₅₄ absorbance, respectively, which were in good agreement with the validation experimental results. A comparison between the modeling results derived through both ANOVA and artificial neural networks (ANN) based on experimental data showed a high correlation coefficient, which indicated that the models were significant and fitted well with experimental results. The results proposed a valuable reference for the treatment of algae-laden surface water in practical application by the optimal coagulation-flocculation process.     

Significant increase of assimilable organic carbon (AOC) levels in MBR effluents followed by coagulation,ozonation and combined treatments: Implications for biostability control of reclaimed water

• Annual AOCs in MBR effluents were stable with small increase in warmer seasons. • Significant increase in AOC levels of tertiary effluents were observed. • Coagulation in prior to ozonation can reduce AOC formation in tertiary treatment. • ∆UV₂₅₄ and SUVA can be surrogates to predict the AOC changes during ozonation. As water reuse development has increased, biological stability issues associated with reclaimed water have gained attention. This study evaluated assimilable organic carbon (AOC) in effluents from a full-scale membrane biological reactor (MBR) plant and found that they were generally stable over one year (125–216 µg/L), with slight increases in warmer seasons. After additional tertiary treatments, the largest increases in absolute and specific AOCs were detected during ozonation, followed by coagulation-ozonation and coagulation. Moreover, UV₂₅₄ absorbance is known to be an effective surrogate to predict the AOC changes during ozonation. Applying coagulation prior to ozonation of MBR effluents for removal of large molecules was found to reduce the AOC formation compared with ozonation treatment alone. Finally, the results revealed that attention should be paid to seasonal variations in influent and organic fraction changes during treatment to enable sustainable water reuse.     

Development of combined coagulation-hydrolysis acidification-dynamic membrane bioreactor system for treatment of oilfield polymer-flooding wastewater

• We created a combined system for treating oilfield polymer-flooding wastewater. • The system was composed of coagulation, hydrolysis acidification and DMBR. • Coagulant integrated with demulsifier dominated the removal of crude oil. • The DMBR proceed efficiently without serious membrane fouling. A combined system composed of coagulation, hydrolysis acidification and dynamic membrane bioreactor (DMBR) was developed for treating the wastewater produced from polymer flooding. Performance and mechanism of the combined system as well as its respective units were also evaluated. The combined system has shown high-capacity to remove all contaminants in the influent. In this work, the coagulant, polyacrylamide-dimethyldiallyammonium chloride-butylacrylate terpolymer (P(DMDAAC-AM-BA)), integrated with demulsifier (SD-46) could remove 91.8% of crude oil and 70.8% of COD. Hydrolysis acidification unit improved the biodegradability of the influent and the experimental results showed that the highest acidification efficiency in hydrolysis acidification reactor was 20.36% under hydraulic retention time of 7 h. The DMBR proceeded efficiently without serious blockage process of membrane fouling, and the concentration of ammonia nitrogen (NH₃-N), oil, chemical oxygen demand and biological oxygen demand in effluent were determined to be 3.4±2.1, 0.3±0.6, 89.7±21.3 and 13±4.7 mg/L.     

Microplastics removal strategies: A step toward finding the solution

• Physical, chemical and biological methods are explored for MPs removal. • Physical methods based on adsorption/filtration are mostly used for MPs removal. • Chemical methods of MPs removal work on coagulation and flocculation mechanism. • MBR technology has also shown the removal of MPs from water. • Global policy on plastic control is lacking. Microplastics are an emerging threat and a big challenge for the environment. The presence of microplastics (MPs) in water is life-threatening to diverse organisms of aquatic ecosystems. Hence, the scientific community is exploring deeper to find treatment and removal options of MPs. Various physical, chemical and biological methods are researched for MPs removal, among which few have shown good efficiency in the laboratory. These methods also have a few limitations in environmental conditions. Other than finding a suitable method, the creation of legal restrictions at a governmental level by imposing policies against MPs is still a daunting task in many countries. This review is an effort to place all effectual MP removal methods in one document to compare the mechanisms, efficiency, advantages, and disadvantages and find the best solution. Further, it also discusses the policies and regulations available in different countries to design an effective global policy. Efforts are also made to discuss the research gaps, recent advancements, and insights in the field.     

Application of Fe(VI) in abating contaminants in water: State of art and knowledge gaps

• The properties of Fe(VI) were summarized. • Both the superiorities and the limitations of Fe(VI) technologies were discussed. • Methods to improve contaminants oxidation/disinfection by Fe(VI) were introduced. • Future research needs for the development of Fe(VI) technologies were proposed. The past two decades have witnessed the rapid development and wide application of Fe(VI) in the field of water de-contamination because of its environmentally benign character. Fe(VI) has been mainly applied as a highly efficient oxidant/disinfectant for the selective elimination of contaminants. The in situ generated iron(III) (hydr)oxides with the function of adsorption/coagulation can further increase the removal of contaminants by Fe(VI) in some cases. Because of the limitations of Fe(VI) per se, various modified methods have been developed to improve the performance of Fe(VI) oxidation technology. Based on the published literature, this paper summarized the current views on the intrinsic properties of Fe(VI) with the emphasis on the self-decay mechanism of Fe(VI). The applications of Fe(VI) as a sole oxidant for decomposing organic contaminants rich in electron-donating moieties, as a bi-functional reagent (both oxidant and coagulant) for eliminating some special contaminants, and as a disinfectant for inactivating microorganisms were systematically summarized. Moreover, the difficulties in synthesizing and preserving Fe(VI), which limits the large-scale application of Fe(VI), and the potential formation of toxic byproducts during Fe(VI) application were presented. This paper also systematically reviewed the important nodes in developing methods to improve the performance of Fe(VI) as oxidant or disinfectant in the past two decades, and proposed the future research needs for the development of Fe(VI) technologies.     

What have we known so far about microplastics in drinking water treatment? A timely review

• 23 available research articles on MPs in drinking water treatment are reviewed. • The effects of treatment conditions and MP properties on MP removal are discussed. • DWTPs with more steps generally are more effective in removing MPs. • Smaller MPs (e.g.,<10 μm) are more challenging in drinking water treatment. Microplastics (MPs) have been widely detected in drinking water sources and tap water, raising the concern of the effectiveness of drinking water treatment plants (DWTPs) in protecting the public from exposure to MPs through drinking water. We collected and analyzed the available research articles up to August 2021 on MPs in drinking water treatment (DWT), including laboratory- and full-scale studies. This article summarizes the major MP compositions (materials, sizes, shapes, and concentrations) in drinking water sources, and critically reviews the removal efficiency and impacts of MPs in various drinking water treatment processes. The discussed drinking water treatment processes include coagulation-flocculation (CF), membrane filtration, sand filtration, and granular activated carbon (GAC) filtration. Current DWT processes that are purposed for particle removal are generally effective in reducing MPs in water. Various influential factors to MP removal are discussed, such as coagulant type and dose, MP material, shape and size, and water quality. It is anticipated that better MP removal can be achieved by optimizing the treatment conditions. Moreover, the article framed the major challenges and future research directions on MPs and nanoplastics (NPs) in DWT.     

Algae (Raphidocelis subcapitata) mitigate combined toxicity of microplastic and lead on Ceriodaphnia dubia

• Micro-plastics (MPs) significantly increase Pb toxicity. • Algae reduce the combined toxicity of MP and Pb. • The toxicity increase comes from high soluble Pb and MP-Pb uptake. • The toxicity reduction might come from energy related pathway. Microplastics (MPs) have been recognized as a new class of emerging contaminants in recent years. They not only directly impact aquatic organisms, but also indirectly impact these organisms by interacting with background toxins in the environment. Moreover, under realistic environmental conditions, algae, a natural food for aquatic organisms, may alter the toxicity pattern related to MPs. In this research, we first examined the toxicity of MPs alone, and their effect on the toxicity of lead (Pb) on Ceriodaphnia dubia (C. dubia), a model aquatic organism for toxicity survey. Then, we investigated the effect of algae on the combined toxicity of MPs and Pb. We observed that, MPs significantly increased Pb toxicity, which was related to the increase in soluble Pb concentration and the intake of Pb-loaded MPs, both of which increased the accumulation of Pb in C. dubia. The presence of algae mitigated the combined toxicity of MPs and Pb, although algae alone increased Pb accumulation. Therefore, the toxicity mitigation through algae uptake came from mechanisms other than Pb accumulation, which will need further investigation.     

Sustainable wood-based nanotechnologies for photocatalytic degradation of organic contaminants in aquatic environment

•Wood and its reassemblies are ideal substrates to develop novel photocatalysts. •Synthetic methods and mechanisms of wood-derived photocatalysts are summarized. •Advances in wood-derived photocatalysts for organic pollutant removal are summed up. •Metal doping, morphology control and semiconductor coupling methods are highlighted. •Structure-activity relationship and catalytic mechanism of photocatalysts are given. Wood-based nanotechnologies have received much attention in the area of photocatalytic degradation of organic contaminants in aquatic environment in recent years, because of the high abundance and renewability of wood as well as the high reaction activity and unique structural features of these materials. Herein, we present a comprehensive review of the current research activities centering on the development of wood-based nanocatalysts for photodegradation of organic pollutants. This review begins with a brief introduction of the development of photocatalysts and hierarchical structure of wood. The review then focuses on strategies of designing novel photocatalysts based on wood or its recombinants (such as 1D fiber, 2D films and 3D porous gels) using advanced nanotechnology including sol-gel method, hydrothermal method, magnetron sputtering method, dipping method and so on. Next, we highlight typical approaches that improve the photocatalytic property, including metal element doping, morphology control and semiconductor coupling. Also, the structure-activity relationship of photocatalysts is emphasized. Finally, a brief summary and prospect of wood-derived photocatalysts is provided.     

Application and mechanism of polysaccharide extracted from Enteromorpha to remove nano-ZnO and humic acid in coagulation process

Green source Ep was extracted from marine alga waste. The molecule model structure of Ep was studied and constructed. PAC-Ep coagulation system improves the efficiency of removal efficiency. Synergistic effects between NPs and HA make a big difference to enhance efficiency. Mechanism is charge neutralization, hydrogen bonding and adsorbing-complexing Enteromorpha polysaccharide (Ep) extracted from alga a novel green coagulant aid for nanoparticles (NPs) and heavy metal ions removal and the structure of EP was intensively studied in this study. The integration of Ep with polyaluminum chloride (PAC-Ep) coagulants exhibited higher coagulation performance than that of the polyaluminum chloride (PAC) because of the negatively charged NPs suspension and humic aid (HA) solution. Significant high removal efficiencies of dissolved organic matter (94.1%), turbidity (99.3%) and Zn ions (69.3%) were achieved by the PAC-Ep coagulants. The dual-coagulation properties of PAC-Ep for different pollutants was based on multiple mechanisms, including (i) Al³⁺ charge neutralization; (ii) hydroxy aluminum hydroxyl bridging formed polynuclearhydroxy complexes bridge and sweep colloidal particles; (iii) adsorption and bridging of Ep chain for the NPs and heavy metal ions. Results indicated that the destabilization of colloid was induced by the coexisting HA and higher removal was achieved as ions adsorption was enhance in the presence of HA complexation. On the basis of that, the extraction of polysaccharide is a promising candidate for its high coagulation performance in water treatment.     

Crosslinking acrylamide with EDTA-intercalated layered double hydroxide for enhanced recovery of Cr(VI) and Congo red: Adsorptive and mechanistic study

• Functional groups of AM and EDTA in composite increased removal of Cr(VI) and CR. • Removal process reached equilibrium within 30 min and was minimally affected by pH. • Elimination of Cr(VI) was promoted by coexisting CR. • Adsorption process of CR was less influenced by the presence of Cr(VI). • Mechanisms were electrostatic attraction, surface complexation and anion exchange. We prepared ethylenediaminetetraacetic acid (EDTA)-intercalated MgAl-layered double hydroxide (LDH-EDTA), then grafted acrylamide (AM) to the LDH-EDTA by a cross-linking method to yield a LDH-EDTA-AM composite; we then evaluated its adsorptive ability for Congo red (CR) and hexavalent chromium (Cr(VI)) in single and binary adsorption systems. The adsorption process on LDH-EDTA-AM for CR and Cr(VI) achieved equilibrium quickly, and the removal efficiencies were minimally affected by initial pH. The maximum uptake quantities of CR and Cr(VI) on LDH-EDTA-AM were 632.9 and 48.47 mg/g, respectively. In mixed systems, chromate removal was stimulated by the presence of CR, while the adsorption efficiency of CR was almost not influenced by coexisting Cr(VI). The mechanisms involved electrostatic attraction, surface complexation, and anion exchange for the adsorption of both hazardous pollutants. In the Cr(VI) adsorption process, reduction also took place. The removal efficiencies in real contaminated water were all higher than those in the laboratory solutions.     

Ceramic water filter for point-of-use water treatment in developing countries: Principles,challenges and opportunities

• CWF is a sustainable POU water treatment method for developing areas. • CWF manufacturing process is critical for its filtration performance. • Simultaneous increase of flow rate and pathogen removal is a challenge. • Control of pore size distribution holds promises to improve CWF efficiency. • Novel coatings of CWFs are a promising method to improve contaminant removal. Drinking water source contamination poses a great threat to human health in developing countries. Point-of-use (POU) water treatment techniques, which improve drinking water quality at the household level, offer an affordable and convenient way to obtain safe drinking water and thus can reduce the outbreaks of waterborne diseases. Ceramic water filters (CWFs), fabricated from locally sourced materials and manufactured by local labor, are one of the most socially acceptable POU water treatment technologies because of their effectiveness, low-cost and ease of use. This review concisely summarizes the critical factors that influence the performance of CWFs, including (1) CWF manufacturing process (raw material selection, firing process, silver impregnation), and (2) source water quality. Then, an in-depth discussion is presented with emphasis on key research efforts to address two major challenges of conventional CWFs, including (1) simultaneous increase of filter flow rate and bacterial removal efficiency, and (2) removal of various concerning pollutants, such as viruses and metal(loid)s. To promote the application of CWFs, future research directions can focus on: (1) investigation of pore size distribution and pore structure to achieve higher flow rates and effective pathogen removal by elucidating pathogen transport in porous ceramic and adjusting manufacture parameters; and (2) exploration of new surface modification approaches with enhanced interaction between a variety of contaminants and ceramic surfaces.     

Phosphorus transformation under the influence of aluminum,organic carbon,and dissolved oxygen at the water-sediment interface: A simulative study

• The three simulation factors caused various changes in both water and sediment. • Responses to simulations differed with the reported natural lakes and wetlands. • Al has dominant effects on sediment P release control among the three factors. • Adding sediment Al can be effective and safe under the simulated conditions. • Polyphosphates were not generated, while added phytate was rather stable. The effects of sediment aluminum (Al), organic carbon (OC), and dissolved oxygen (DO) on phosphorus (P) transformation, at the water-sediment interface of a eutrophic constructed lake, were investigated via a series of simulative experiments. The above three factors had various influences on dissolved P concentration, water pH, water and surface sediment appearance, and P fractions. Additions of Al had the greatest effect on suppressing P release, and the water pH remained alkaline in the water-sediment system under various OC and DO conditions. No dissolution of the added Al was detected. ³¹P-NMR characterization suggested that OC addition did not promote biological P uptake to polyphosphates under oxic conditions. The simulation result on the added phytate indicated the absence of phytate in the original lake sediment. As compared to the reported natural lakes and wetland, the water-sediment system of the constructed lake responded differently to some simulative conditions. Since Al, OC, and DO can be controlled with engineering methods, the results of this study provide insights for the practical site restorations.     

Identification of sources,characteristics and photochemical transformations of dissolved organic matter with EEM-PARAFAC in the Wei River of China

• The source of DOM in surface water and sediment is inconsistent. • The DOC content changes differently in surface water and sediment. • The content of DOC in the surface water is lower than that in the sediment. • The DOM in the surface water had higher photodegradation potentials than sediment. Dissolved organic matter (DOM) in rivers is a critical regulator of the cycling and toxicity of pollutants and the behavior of DOM is a key indicator for the health of the environment. We investigated the sources and characteristics of DOM in surface water and sediment samples of the Wei River, China. Dissolved organic carbon (DOC) concentration and ultraviolet absorbance at 254 nm (UV₂₅₄) increased in the surface water and were decreased in the sediment downstream, indicating that the source of DOM in the water differed from the sediment. Parallel factor (PARAFAC) analysis of the excitation-emission matrices (EEM) revealed the presence of terrestrial humus-like, microbial humus-like and tryptophan-like proteins in the surface water, whereas the sediment contained UVA humic-like, UVC humic-like and fulvic-like in the sediment. The DOM in the surface water and sediment were mainly derived from microbial metabolic activity and the surrounding soil. Surface water DOM displayed greater photodegradation potential than sediment DOM. PARAFAC analysis indicated that the terrestrial humic-like substance in the water and the fulvic-like component in the sediment decomposed more rapidly. These data describe the characteristics of DOM in the Wei River and are crucial to understanding the fluctuations in environmental patterns.     

Using loose nanofiltration membrane for lake water treatment: A pilot study

• A pilot study was conducted for drinking water treatment using loose NF membranes. • The membranes had very high rejection of NOM and medium rejection of Ca²⁺/Mg²⁺. • Organic fouling was dominant and contribution of inorganic fouling was substantial. • Both organic and inorganic fouling had spatial non-uniformity on membrane surface. • Applying EDTA at basic conditions was effective in removing membrane fouling. Nanofiltration (NF) using loose membranes has a high application potential for advanced treatment of drinking water by selectively removing contaminants from the water, while membrane fouling remains one of the biggest problems of the process. This paper reported a seven-month pilot study of using a loose NF membrane to treat a sand filtration effluent which had a relatively high turbidity (~0.4 NTU) and high concentrations of organic matter (up to 5 mg/L as TOC), hardness and sulfate. Results showed that the membrane demonstrated a high rejection of TOC (by>90%) and a moderately high rejection of two pesticides (54%–82%) while a moderate rejection of both calcium and magnesium (~45%) and a low rejection of total dissolved solids (~27%). The membrane elements suffered from severe membrane fouling, with the membrane permeance decreased by 70% after 85 days operation. The membrane fouling was dominated by organic fouling, while biological fouling was moderate. Inorganic fouling was mainly caused by deposition of aluminum-bearing substances. Though inorganic foulants were minor contents on membrane, their contribution to overall membrane fouling was substantial. Membrane fouling was not uniform on membrane. While contents of organic and inorganic foulants were the highest at the inlet and outlet region, respectively, the severity of membrane fouling increased from the inlet to the outlet region of membrane element with a difference higher than 30%. While alkaline cleaning was not effective in removing the membrane foulants, the use of ethylenediamine tetraacetate (EDTA) at alkaline conditions could effectively restore the membrane permeance.     

In situ formation of bimetallic FeNi nanoparticles on sand through green technology: Application for tetracycline removal

• In situ preparation of FeNi nanoparticles on the sand via green synthesis approach. • Removal of tetracycline using GS-FeNi in batch and column study. • Both reductive degradation and sorption played crucial role the process. • Reusability of GS-FeNi showed about 77.39±4.3% removal on 4th cycle. • TC by-products after interaction showed less toxic as compared with TC. In this study, FeNi nanoparticles were green synthesized using Punica granatum (pomegranate) peel extract, and these nanoparticles were also formed in situ over quartz sand (GS-FeNi) for removal of tetracycline (TC). Under the optimized operating conditions, (GS-FeNi concentration: 1.5% w/v; concentration of TC: 20 mg/L; interaction period: 180 min), 99±0.2% TC removal was achieved in the batch reactor. The removal capacity was 181±1 mg/g. A detailed characterization of the sorbent and the solution before and after the interaction revealed that the removal mechanism(s) involved both the sorption and degradation of TC. The reusability of reactant was assessed for four cycles of operation, and 77±4% of TC removal was obtained in the cycle. To judge the environmental sustainability of the process, residual toxicity assay of the interacted TC solution was performed with indicator bacteria (Bacillus and Pseudomonas) and algae (Chlorella sp.), which confirmed a substantial decrease in the toxicity. The continuous column studies were undertaken in the packed bed reactors using GS-FeNi. Employing the optimized conditions, quite high removal efficiency (978±5 mg/g) was obtained in the columns. The application of GS-FeNi for antibiotic removal was further evaluated in lake water, tap water, and ground water spiked with TC, and the removal capacity achieved was found to be 781±5, 712±5, and 687±3 mg/g, respectively. This work can pave the way for treatment of antibiotics and other pollutants in the reactors using novel green composites prepared from fruit wastes.     

Mechanism of dichloromethane disproportionation over mesoporous TiO2 under low temperature

• Mechanism of DCM disproportionation over mesoporous TiO₂ was studied. • DCM was completely eliminated at 350℃ under 1 vol.% humidity. • Anatase (001) was the key for disproportionation. • A competitive oxidation route co-existed with disproportionation. • Disproportionation was favored at low temperature. Mesoporous TiO₂ was synthesized via nonhydrolytic template-mediated sol-gel route. Catalytic degradation performance upon dichloromethane over as-prepared mesoporous TiO₂, pure anatase and rutile were investigated respectively. Disproportionation took place over as-made mesoporous TiO₂ and pure anatase under the presence of water. The mechanism of disproportionation was studied by in situ FTIR. The interaction between chloromethoxy species and bridge coordinated methylenes was the key step of disproportionation. Formate species and methoxy groups would be formed and further turned into carbon monoxide and methyl chloride. Anatase (001) played an important role for disproportionation in that water could be dissociated into surface hydroxyl groups on such structure. As a result, the consumed hydroxyl groups would be replenished. In addition, there was another competitive oxidation route governed by free hydroxyl radicals. In this route, chloromethoxy groups would be oxidized into formate species by hydroxyl radicals transfering from the surface of TiO₂. The latter route would be more favorable at higher temperature.     

Unlocked disinfection by-product formation potential upon exposure of swimming pool water to additional stimulants

• Swimming pool water was studied for DBPs upon exposure to additional stimulants. • DBP formation could be induced by residual chlorine and extended incubation. • Urine led to a massive formation of chloroform with additional stimulants. • Reactions between chlorine and anthropogenic organics were slow and long-lasting. • Urine control and air ventilation should be on the priority list for pool management. Anthropogenic organics are known to be responsible for the formation of harmful disinfection by-products (DBPs) in swimming pool water (SPW). The research explored an important scenario of SPW with no additional anthropogenic organic input. With stimulations by residual chlorine or additional chlorine and extended incubation, the formation of DBPs, especially chloroform, was significantly induced. Similar observations were found by investigating synthetic SPW made with sweat and urine. The presence of urine led to a massive formation of chloroform, as noted by an approximate 19-fold increase after 165-day incubation with a shock chlorine dose. The research suggests that consistent residual chlorine and long water retention as two typical features of SPW could unlock the DBP formation potential of anthropogenic organics. Thus, limiting the introduction of anthropogenic organics may not have an immediate effect on reducing DBP levels, because their reactions with chlorine can be slow and long-lasting. Pool management should prioritize on control of urine and improving air ventilation. This work is useful to deepen understandings about DBP formation in SPW and provide implications for pool management and prospective legislation.     

Degradation of refractory organics in concentrated leachate by the Fenton process: Central composite design for process optimization

• 90% total COD, 95.3% inert COD and 97.2% UV₂₅₄ were removed. • High R² values (over 95%) for all responses were obtained with CCD. • Operational cost was calculated to be 0.238 €/g COD_removed for total COD removal. • Fenton oxidation was highly-efficient method for inert COD removal. • BOD₅/COD ratio of leachate concentrate raised from 0.04 to 0.4. The primary aim of this study is inert COD removal from leachate nanofiltration concentrate because of its high concentration of resistant organic pollutants. Within this framework, this study focuses on the treatability of leachate nanofiltration concentrate through Fenton oxidation and optimization of process parameters to reach the maximum pollutant removal by using response surface methodology (RSM). Initial pH, Fe²⁺ concentration, H₂O₂/Fe²⁺ molar ratio and oxidation time are selected as the independent variables, whereas total COD, color, inert COD and UV₂₅₄ removal are selected as the responses. According to the ANOVA results, the R² values of all responses are found to be over 95%. Under the optimum conditions determined by the model (pH: 3.99, Fe²⁺: 150 mmol/L, H₂O₂/Fe²⁺: 3.27 and oxidation time: 84.8 min), the maximum COD removal efficiency is determined as 91.4% by the model. The color, inert COD and UV₂₅₄ removal efficiencies are determined to be 99.9%, 97.2% and 99.5%, respectively, by the model, whereas the total COD, color, inert COD and UV₂₅₄ removal efficiencies are found respectively to be 90%, 96.5%, 95.3% and 97.2%, experimentally under the optimum operating conditions. The Fenton process improves the biodegradability of the leachate NF concentrate, increasing the BOD₅/COD ratio from the value of 0.04 to the value of 0.4. The operational cost of the process is calculated to be 0.238 €/g COD_removed. The results indicate that the Fenton oxidation process is an efficient and economical technology in improvement of the biological degradability of leachate nanofiltration concentrate and in removal of resistant organic pollutants.     

Electro-assisted CNTs/ceramic flat sheet ultrafiltration membrane for enhanced antifouling and separation performance

• A stable and electroconductive CNTs/ceramic membrane was fabricated. • The membrane with the electro-assistance exhibited optimal fouling mitigation. • The removal efficiency was improved by the -2.0 V electro-assistance. • Electro-assisted filtration is energy-saving than that of commercial membrane. Ultrafiltration is employed as an important process for water treatment and reuse, which is of great significance to alleviate the shortage of water resources. However, it suffers from severe membrane fouling and the trade-off between selectivity and permeability. In this work, a CNTs/ceramic flat sheet ultrafiltration membrane coupled with electro-assistance was developed for improving the antifouling and separation performance. The CNTs/ceramic flat sheet membrane was fabricated by coating cross-linked CNTs on ceramic membrane, featuring a good electroconductivity of 764.75 S/m. In the filtration of natural water, the permeate flux of the membrane with the cell voltage of -2.0 V was 1.8 times higher than that of the membrane without electro-assistance and 5.7-fold greater than that of the PVDF commercial membrane. Benefiting from the electro-assistance, the removal efficiency of the typical antibiotics was improved by 50%. Furthermore, the electro-assisted membrane filtration process showed 70% reduction in energy consumption compared with the filtration process of the commercial membrane. This work offers a feasible approach for membrane fouling mitigation and effluent quality improvement and suggests that the electro-assisted CNTs/ceramic membrane filtration process has great potential in the application of water treatment.