Analytical solution to evaluate salt precipitation during CO2 injection in saline aquifers

Carbon dioxide sequestration in deep saline aquifers is a means of reducing anthropogenic atmospheric emissions of CO₂. Among various mechanisms, CO₂ can be trapped in saline aquifers by dissolution in the formation water. Vaporization of water occurs along with the dissolution of CO₂. Vaporization can cause salt precipitation, which reduces porosity and impairs permeability of the reservoir in the vicinity of the wellbore, and can lead to reduction in injectivity. The amount of salt precipitation and the region in which it occurs may be important in CO₂ storage operations if salt precipitation significantly reduces injectivity. Here we develop an analytical model, as a simple and efficient tool to predict the amount of salt precipitation over time and space. This model is particularly useful at high injection velocities, when viscous forces dominate.First, we develop a model which treats the vaporization of water and dissolution of CO₂ in radial geometry. Next, the model is used to predict salt precipitation. The combined model is then extended to evaluate the effect of salt precipitation on permeability in terms of a time-dependent skin factor. Finally, the analytical model is corroborated by application to a specific problem with an available numerical solution, where a close agreement between the solutions is observed. We use the results to examine the effect of assumptions and approximations made in the development of the analytical solution. For cases studied, salt saturation was a few percent. The loss in injectivity depends on the degree of reduction of formation permeability with increased salt saturation. For permeability-reduction models considered in this work, the loss in injectivity was not severe. However, one limitation of the model is that it neglects capillary and gravity forces, and these forces might increase salt precipitation at the bottom of formation particularly when injection rate is low.     

Integration of counter-current relative permeability in the simulation of CO2 injection into saline aquifers

Carbon dioxide (CO₂) injection into saline aquifers is one of the promising options to sequester large amounts of CO₂ in geological formations. During as well as after injection of CO₂ into an aquifer, CO₂ migrates towards the top of the formation due to density differences between the formation brine and the injected CO₂. The time scales of CO₂ migration towards the top of an aquifer and the fraction of CO₂ that is trapped as residual gas depends strongly on the driving forces that are acting on the injected CO₂.When CO₂ migrates to the top of an aquifer, brine may be displaced downwards in a counter-current flow setting particularly during the injection period. A majority of the published work on counter-current flow settings have reported significant reductions in the associated relative permeability functions as compared to co-current measurements. However, this phenomenon has not yet been considered in the simulation of CO₂ storage into saline aquifers.In this paper we study the impact of changes in mobility for the two-phase brine/CO₂ system as a result of transitions between co- and counter-current flow settings. We have included this effect in a simulator and studied the impact of the related mobility reduction on the saturation distribution and residual saturation of CO₂ in aquifers over relevant time scales. We demonstrate that the reduction in relative permeability in the vertical direction changes the plume migration pattern and has an impact on the amount of gas that is trapped as a function of time. This is to our best knowledge the first attempt to integrate counter-current relative permeability into the simulation of injection and subsequent migration of CO₂ in aquifers. The results and analysis presented in this paper are directly relevant to all ongoing activities related to the design of large-scale CO₂ storage in saline aquifers.     

Numerical investigation concerning the impact of CO2 geologic storage on regional groundwater flow

Large-scale storage of carbon dioxide in saline aquifers may cause considerable pressure perturbation and brine migration in deep rock formations, which may have a significant influence on the regional groundwater system. With the help of parallel computing techniques, we conducted a comprehensive, large-scale numerical simulation of CO₂ geologic storage that predicts not only CO₂ migration, but also its impact on regional groundwater flow. As a case study, a hypothetical industrial-scale CO₂ injection in Tokyo Bay, which is surrounded by the most heavily industrialized area in Japan, was considered, and the impact of CO₂ injection on near-surface aquifers was investigated, assuming relatively high seal-layer permeability (higher than 10 microdarcy). A regional hydrogeological model with an area of about 60 km × 70 km around Tokyo Bay was discretized into about 10 million gridblocks. To solve the high-resolution model efficiently, we used a parallelized multiphase flow simulator TOUGH2-MP/ECO2N on a world-class high performance supercomputer in Japan, the Earth Simulator. In this simulation, CO₂ was injected into a storage aquifer at about 1 km depth under Tokyo Bay from 10 wells, at a total rate of 10 million tons/year for 100 years. Through the model, we can examine regional groundwater pressure buildup and groundwater migration to the land surface. The results suggest that even if containment of CO₂ plume is ensured, pressure buildup on the order of a few bars can occur in the shallow confined aquifers over extensive regions, including urban inlands.     

Large-scale impact of CO2 storage in deep saline aquifers: A sensitivity study on pressure response in stratified systems

Large volumes of CO₂ captured from carbon emitters (such as coal-fired power plants) may be stored in deep saline aquifers as a means of mitigating climate change. Storing these additional fluids may cause pressure changes and displacement of native brines, affecting subsurface volumes that can be significantly larger than the CO₂ plume itself. This study aimed at determining the three-dimensional region of influence during/after injection of CO₂ and evaluating the possible implications for shallow groundwater resources, with particular focus on the effects of interlayer communication through low-permeability seals. To address these issues quantitatively, we conducted numerical simulations that provide a basic understanding of the large-scale flow and pressure conditions in response to industrial-scale CO₂ injection into a laterally open saline aquifer. The model domain included an idealized multilayered groundwater system, with a sequence of aquifers and aquitards (sealing units) extending from the deep saline storage formation to the uppermost freshwater aquifer. Both the local CO₂-brine flow around the single injection site and the single-phase water flow (with salinity changes) in the region away from the CO₂ plume were simulated. Our simulation results indicate considerable pressure buildup in the storage formation more than 100 km away from the injection zone, whereas the lateral distance migration of brine is rather small. In the vertical direction, the pressure perturbation from CO₂ storage may reach shallow groundwater resources only if the deep storage formation communicates with the shallow aquifers through sealing units of relatively high permeabilities (higher than 10^?18 m²). Vertical brine migration through a sequence of layers into shallow groundwater bodies is extremely unlikely. Overall, large-scale pressure changes appear to be of more concern to groundwater resources than changes in water quality caused by the migration of displaced saline water.     

An experimental and numerical investigation into the impact of dissolution/precipitation mechanisms on CO2 injectivity in the wellbore and far field regions

Carbon dioxide capture and storage (CCS) technology is gaining credibility as the best short to medium term solution for significantly reducing net carbon emissions into the atmosphere. From a capacity point of view, deep saline aquifers offer the greatest potential for CO₂ storage. In this respect, well injectivity is considered a key technical and economical issue. Rock/fluid interactions – dissolution/precipitation of minerals, in particular carbonates – are currently considered as one of the principal reasons for wellbore injectivity changes in aquifers.This research investigated the mechanisms involved in injectivity losses through experimental and theoretical methods. The impact on injectivity of permeability changes occurring at various distances from the wellbore was studied using an idealised CO₂ injection well flow model. A new experimental set-up was used to investigate the effect on dissolution/precipitation mechanisms of the pressure and temperature changes that the fluid is subjected to as it advances from the wellbore.Numerical modelling of the injection wellbore has shown that changes in the petrophysical properties of the reservoir several metres away from the wellbore can still have a significant impact on injectivity. As indicated by the experimental research carried out, pressure and temperature gradients that exist inside the reservoirs may lead to re-precipitation in the far field, however no significant permeability and porosity changes were detected to suggest major losses of injectivity due to these effects.     

Investigations on CO2 storage capacity in saline aquifers—Part 2: Estimation of storage capacity coefficients

Many studies on geological carbon dioxide (CO₂) storage capacity neglect the influence of complex coupled processes which occur during and after the injection of CO₂. Storage capacity is often overestimated since parts of the reservoirs cannot be reached by the CO₂ plume due to gravity segregation and are thus not accessible for storage. This work investigates the effect of reservoir parameters like depth, temperature, absolute and relative permeability, and capillary pressure on the processes during CO₂ injection and thus on estimates of effective storage capacity. The applied statistical characteristics of parameters are based on a large reservoir parameter database. Different measured relative permeability relations are considered. The methodology of estimating storage capacity is discussed. Using numerical 1D and 3D experiments, detailed time-dependent storage capacity estimates are derived. With respect to the concept developed in this work, it is possible to estimate effective CO₂ storage capacity in saline aquifers. It is shown that effective CO₂ mass stored in the reservoir varies by a factor of 20 for the reservoir setups considered. A high influence of the relative permeability relation on storage capacity is shown.     

Basin-scale hydrogeologic impacts of CO2 storage: Capacity and regulatory implications

Industrial-scale injection of CO₂ into saline formations in sedimentary basins will cause large-scale fluid pressurization and migration of native brines, which may affect valuable groundwater resources overlying the deep sequestration aquifers. In this paper, we discuss how such basin-scale hydrogeologic impacts (1) may reduce current storage capacity estimates, and (2) can affect regulation of CO₂ storage projects. Our assessment arises from a hypothetical future carbon sequestration scenario in the Illinois Basin, which involves twenty individual CO₂ storage projects (sites) in a core injection area most suitable for long-term storage. Each project is assumed to inject five million tonnes of CO₂ per year for 50 years. A regional-scale three-dimensional simulation model was developed for the Illinois Basin that captures both the local-scale CO₂–brine flow processes and the large-scale groundwater flow patterns in response to CO₂ storage. The far-field pressure buildup predicted for this selected sequestration scenario support recent studies in that environmental concerns related to near- and far-field pressure buildup may be a limiting factor on CO₂ storage capacity. In other words, estimates of storage capacity, if solely based on the effective pore volume available for safe trapping of CO₂, may have to be revised based on assessments of pressure perturbations and their potential impacts on caprock integrity and groundwater resources. Our results suggest that (1) the area that needs to be characterized in a permitting process may comprise a very large region within the basin if reservoir pressurization is considered, and (2) permits cannot be granted on a single-site basis alone because the near- and far-field hydrogeologic response may be affected by interference between individual storage sites. We also discuss some of the challenges in making reliable predictions of large-scale hydrogeologic impacts related to CO₂ sequestration projects.     

A method for quick assessment of CO2 storage capacity in closed and semi-closed saline formations

Saline aquifers of high permeability bounded by overlying/underlying seals may be surrounded laterally by low-permeability zones, possibly caused by natural heterogeneity and/or faulting. Carbon dioxide (CO₂) injection into and storage in such “closed” systems with impervious seals, or “semi-closed” systems with non-ideal (low permeability) seals, is different from that in “open” systems, from which the displaced brine can easily escape laterally. In closed or semi-closed systems, the pressure buildup caused by continuous industrial-scale CO₂ injection may have a limiting effect on CO₂ storage capacity, because geomechanical damage caused by overpressure needs to be avoided. In this research, a simple analytical method was developed for the quick assessment of the CO₂ storage capacity in such closed and semi-closed systems. This quick-assessment method is based on the fact that native brine (of an equivalent volume) displaced by the cumulative injected CO₂ occupies additional pore volume within the storage formation and the seals, provided by pore and brine compressibility in response to pressure buildup. With non-ideal seals, brine may also leak through the seals into overlying/underlying formations. The quick-assessment method calculates these brine displacement contributions in response to an estimated average pressure buildup in the storage reservoir. The CO₂ storage capacity and the transient domain-averaged pressure buildup estimated through the quick-assessment method were compared with the “true” values obtained using detailed numerical simulations of CO₂ and brine transport in a two-dimensional radial system. The good agreement indicates that the proposed method can produce reasonable approximations for storage–formation–seal systems of various geometric and hydrogeological properties.     

Screening and selection of sites for CO2 sequestration based on pressure buildup

This paper presents a simple methodology for estimating pressure pressure buildup due to the injection of supercritical CO₂into a saline formation, and the limiting pressure at which the formation starts to fracture. Pressure buildup is calculated using the approximate solution of Mathias et al. [Mathias, S.A., Hardisty, P.E., Trudell, M.R., Zimmerman, R.W., 2009. Approximate solutions for pressure buildup during CO₂ injection in brine aquifers. Transp. Porous Media. doi:10.1007/s11242-008-9316-7], which accounts for two-phase Forchheimer flow (of supercritical CO₂ and brine) in a compressible porous medium. Compressibility of the rock formation and both fluid phases are also accounted for. Injection pressure is assumed to be limited by the pressure required to fracture the rock formation. Fracture development is assumed to occur when pore pressures exceed the minimum principal stress, which in turn is related to the Poisson’s ratio of the rock formation. Detailed guidance is also offered concerning the estimation of viscosity, density and compressibility for the brine and CO₂. Example calculations are presented in the context of data from the Plains CO₂ Reduction (PCOR) Partnership. Such a methodology will be useful for screening analysis of potential CO₂ injection sites to identify which are worthy of further investigation.     

CO2 storage capacity estimation: Methodology and gaps

Implementation of CO₂ capture and geological storage (CCGS) technology at the scale needed to achieve a significant and meaningful reduction in CO₂ emissions requires knowledge of the available CO₂ storage capacity. CO₂ storage capacity assessments may be conducted at various scales—in decreasing order of size and increasing order of resolution: country, basin, regional, local and site-specific. Estimation of the CO₂ storage capacity in depleted oil and gas reservoirs is straightforward and is based on recoverable reserves, reservoir properties and in situ CO₂ characteristics. In the case of CO₂-EOR, the CO₂ storage capacity can be roughly evaluated on the basis of worldwide field experience or more accurately through numerical simulations. Determination of the theoretical CO₂ storage capacity in coal beds is based on coal thickness and CO₂ adsorption isotherms, and recovery and completion factors. Evaluation of the CO₂ storage capacity in deep saline aquifers is very complex because four trapping mechanisms that act at different rates are involved and, at times, all mechanisms may be operating simultaneously. The level of detail and resolution required in the data make reliable and accurate estimation of CO₂ storage capacity in deep saline aquifers practical only at the local and site-specific scales. This paper follows a previous one on issues and development of standards for CO₂ storage capacity estimation, and provides a clear set of definitions and methodologies for the assessment of CO₂ storage capacity in geological media. Notwithstanding the defined methodologies suggested for estimating CO₂ storage capacity, major challenges lie ahead because of lack of data, particularly for coal beds and deep saline aquifers, lack of knowledge about the coefficients that reduce storage capacity from theoretical to effective and to practical, and lack of knowledge about the interplay between various trapping mechanisms at work in deep saline aquifers.     

Storage of CO2 in saline aquifers: Effects of gravity, viscous, and capillary forces on amount and timing of trapping

CO₂ can be effectively immobilized during CO₂ injection into saline aquifers by residual trapping – also known as capillary trapping – a process resulting from capillary snap-off of isolated CO₂ bubbles. Simulations of CO₂ injection were performed to investigate the interplay of viscous and gravity forces and capillary trapping of CO₂. Results of those simulations show that gas injection processes in which gravitational forces are weak compared to viscous forces (low gravity number N_gv) trap significantly more CO₂ than do flows with strong gravitational forces relative to the viscous forces (high N_gv). The results also indicate that over a wide range of gravity numbers (N_gv), significant fractions of the trapping of CO₂ can occur relatively quickly. The amount of CO₂ that is trapped after injection ceases is demonstrated to correlate with N_gv. For some simulated displacements, effects of capillary pressure and aquifer dip angle on the amount and the rate of trapping are reported. Trapping increases when effects of capillary pressure and aquifer inclination are included in the model. Finally we show that injection schemes such as alternating injection of brine and CO₂ or brine injection after CO₂ injection can also enhance the trapping behavior.     

Corrective measures based on pressure control strategies for CO2 geological storage in deep aquifers

A prerequisite to the wide deployment at an industrial scale of CO₂ geological storage is demonstrating that potential risks can be efficiently managed. Corrective measures in case of significant irregularities, such as CO₂ leakage, are hence required as advocated by the recent European directive on Carbon Capture and Storage operations. In this regard, the objective of the present paper is to investigate four different corrective measures aiming at controlling the overpressure induced by the injection operations in the reservoir: stopping the CO₂ injection and relying on the natural pressure recovery in the reservoir; extracting the stored CO₂ at the injection well; extracting brine at a distant well while stopping the CO₂ injection, and extracting at a distant well without stopping the CO₂ injection. The efficiency of the measures is assessed using multi-phase fluid flow numerical simulations. The application case is the deep carbonate aquifer of the Dogger geological unit in the Paris Basin. A comparative study between the four corrective measures is then carried using a cost-benefit approach. Results show that an efficient overpressure reduction can be achieved by simply shutting-in the well. The overpressure reduction can be significantly accelerated by means of fluid extraction but the adverse consequences are the associated higher costs of the intervention operations.     

Intermediate storage of carbon dioxide in geological formations: A technical perspective

Enhanced oil recovery (EOR) through CO₂ flooding has been practiced on a commercial basis for the last 35 years and continues today at several sites, currently injecting in total over 30 million tons of CO₂ annually. This practice is currently exclusively for economic gain, but can potentially contribute to the reduction of emissions of greenhouse gases provided it is implemented on a large scale. Optimal operations in distributing CO₂ to CO₂-EOR or enhanced gas recovery (EGR) projects (referred to here collectively as CO₂-EHR) on a large scale and long time span imply that intermediate storage of CO₂ in geological formations may be a key component. Intermediate storage is defined as the storage of CO₂ in geological media for a limited time span such that the CO₂ can be sufficiently reproduced for later use in CO₂-EHR. This paper investigates the technical aspects, key individual parameters and possibilities of intermediate storage of CO₂ in geological formations aiming at large scale implementation of carbon dioxide capture and storage (CCS) for deep emission reduction. The main parameters are thus the depth of injection and density, CO₂ flow and transport processes, storage mechanisms, reservoir heterogeneity, the presence of impurities, the type of the reservoirs and the duration of intermediate storage. Structural traps with no flow of formation water combined with proper injection planning such as gas-phase injection favour intermediate storage in deep saline aquifers. In depleted oil and gas fields, high permeability, homogeneous reservoirs with structural traps (e.g. anticlinal structures) are good candidates for intermediate CO₂ storage. Intuitively, depleted natural gas reservoirs can be potential candidates for intermediate storage of carbon dioxide due to similarity in storage characteristics.     

Assessing the economic feasibility of regional deep saline aquifer CO2 injection and storage: A geomechanics-based workflow applied to the Rose Run sandstone in Eastern Ohio, USA

Typical top-down regional assessments of CO₂ storage feasibility are sufficient for determining the maximum volumetric capacity of deep saline aquifers. However, they do not reflect the regional economic feasibility of storage. This is controlled, in part, by the number and type of injection wells that are necessary to achieve regional CO₂ storage goals. In contrast, the geomechanics-based assessment workflow that we present in this paper follows a bottom-up approach for evaluating regional deep saline aquifer CO₂ storage feasibility. The CO₂ storage capacity of an aquifer is a function of its porous volume as well as its CO₂ injectivity. For a saline aquifer to be considered feasible in this assessment it must be able to store a specified amount of CO₂ at a reasonable cost per ton of CO₂. The proposed assessment workflow has seven steps that include (1) defining the storage project and goals, (2) characterizing the geology and developing a geomechanical model of the aquifer, (3) constructing 3D aquifer models, (4) simulating CO₂ injection, (5,6) evaluating CO₂ injection and storage feasibility (with and without injection well stimulation), and (7) determining whether it is economically feasible to proceed with the storage project. The workflow was applied to a case study of the Rose Run sandstone aquifer in the Eastern Ohio River Valley, USA. We found that it is feasible in this region to inject 113 Mt CO₂/year for 30 years at an associated well cost of less than US $1.31/t CO₂, but only if injectivity enhancement techniques such as hydraulic fracturing and injection induced micro-seismicity are implemented.     

Simultaneous CO2 injection and water production to optimise aquifer storage capacity

The estimates for geological CO₂ storage capacity worldwide vary, but it is generally believed that the capacity in saline aquifers will be sufficient for the amounts of CO₂ that will need to be stored. The effort required to select and qualify a geological storage site for safe storage will, however, be significant and storage capacity may be a limited resource regionally. Both from a economic and resource management perspective it is therefore important that potential storage sites are exploited to their full potential.In static capacity estimates, where the maximum stored amount of CO₂ is given as a fraction of the formation pore volume, typically arrive at efficiency factors in the range of a few per cents. Recent work has shown that when the dynamic behaviour of the injected CO₂ is taken into account, the efficiency factor will be reduced because of the increase in pore pressure in the region around the injection well(s). The increase in pore pressure will propagate much further than the CO₂. The EU directive on geological CO₂ storage specifically addresses the restriction that will apply when different storage sites are interacting due to pressure communication. Consequently, the pore pressure increase at the boundary of the storage license area will be an important limiting factor for the amount of CO₂ that can be injected.One obvious method to control the pore pressure is to produce water from the aquifer at some distance from the CO₂ injection wells. This paper discusses results from simulations of CO₂ injection in two aquifers on the Norwegian Continental Shelf; the Johansen aquifer and the southern part of the Utsira aquifer. These aquifers are candidates for injection of CO₂ shipped out via pipeline from the Norwegian West Coast. The injected amounts of CO₂ over a period of 50 years are 0.518 Gtonne for the Johansen aquifer and 1.04 Gtonne for the Utsira aquifer.Several design options for the injection operations are investigated: Injection of CO₂ without water production; injection into several wells to distribute the injected fluids and reduce the local pressure increase around each injection well; and injection with simultaneous production of water from one or more wells. The boundaries of the aquifer formations are assumed closed in all simulations. The possible consequences of other types of boundary conditions (semi-closed or open) are briefly discussed.     

Water/acid gas interfacial tensions and their impact on acid gas geological storage

Acid gas geological disposal is a promising process to reduce CO₂ atmospheric emissions and an environment-friendly and economic alternative to the transformation of H₂S into sulphur by the Claus process. Acid gas confinement in geological formations is to a large extent controlled by the capillary properties of the water/acid–gas/caprock system, because a significant fraction of the injected gas rises buoyantly and accumulates beneath the caprock. These properties include the water/acid gas interfacial tension (IFT), to which the so-called capillary entry pressure of the gas in the water-saturated caprock is proportional. In this paper we present the first ever systematic water/acid gas IFT measurements carried out by the pendant drop technique under geological storage conditions. We performed IFT measurements for water/H₂S systems over a large range of pressure (up to P = 15 MPa) and temperature (up to T = 120 °C). Water/H₂S IFT decreases with increasing P and levels off at around 9–10 mN/m at high T (≥70 °C) and P (>12 MPa). The latter values are around 30–40% of water/CO₂ IFTs, and around 20% of water/CH₄ IFTs at similar T and P conditions. The IFT between water and a CO₂ + H₂S mixture at T = 77 °C and P > 7.5 MPa is observed to be approximately equal to the molar average IFT of the water/CO₂ and water/H₂S binary mixtures. Thus, when the H₂S content in the stored acid gas increases the capillary entry pressure decreases, together with the maximum height of acid gas column and potential storage capacity of a given geological formation. Hence, considerable attention should be exercised when refilling with a H₂S-rich acid gas a depleted gas reservoir, or a depleted oil reservoir with a gas cap: in the case of hydrocarbon reservoirs that were initially (i.e., at the time of their discovery) close to capillary leakage, acid gas leakage through the caprock will inevitably occur if the refilling pressure approaches the initial reservoir pressure.     

Scenario simulations of CO2 injection feasibility, plume migration and storage in a saline aquifer, Scania, Sweden

Deep saline aquifers have large capacity for geological CO₂ storage, but are generally not as well characterized as petroleum reservoirs. We here aim at quantifying effects of uncertain hydraulic parameters and uncertain stratigraphy on CO₂ injectivity and migration, and provide a first feasibility study of pilot-scale CO₂ injection into a multilayered saline aquifer system in southwest Scania, Sweden. Four main scenarios are developed, corresponding to different possible interpretations of available site data. Simulation results show that, on the one hand, stratigraphic uncertainty (presence/absence of a thin mudstone/claystone layer above the target storage formation) leads to large differences in predicted CO₂ storage in the target formation at the end of the test (ranging between 11% and 98% of injected CO₂ remaining), whereas other parameter uncertainty (in formation and cap rock permeabilities) has small impact. On the other hand, the latter has large impact on predicted injectivity, on which stratigraphic uncertainty has small impact. Salt precipitation at the border of the target storage formation affects CO₂ injectivity for all considered scenarios and injection rates. At low injection rates, salt is deposited also within the formation, considerably reducing its availability for CO₂ storage.     

Application of crosswell seismic tomography using difference analysis with data normalization to monitor CO2 flooding in an aquifer

A pilot-scale experiment for carbon dioxide (CO₂) sequestration was undertaken at the Nagaoka test field in Japan. Time-lapse crosswell seismic tomography was conducted to detect and monitor the movement of CO₂ injected into an aquifer. We applied difference analysis with data normalization (DADN) to the time-lapse data to eliminate false images that were apparent in a conventionally processed difference section. Conventional difference analysis calculates travel-time delays after inversion, whereas the DADN method calculates them from raw travel-time records before inversion. Thus, fewer errors are generated with the DADN method compared to a conventional inversion analysis. We applied the DADN method to time-lapse tomography data recorded before and after the injection of CO₂ and computed the velocity variation in a subsurface section, which clearly showed the distribution of CO₂ flooding within a high permeability zone in the aquifer and showed no CO₂ leakage into the caprock. Our results also show the maximum velocity decrease as a result of CO₂ injection was about 9%, which is close to the results obtained in laboratory experiments. Finally, numerical simulations were inverted to test the effectiveness of the conventional and DADN methods in dealing with noise. These tests showed that the DADN method effectively reduces unique coherent noise for particular receiver and source combinations. We concluded that the DADN method provides useful data for monitoring the flow of CO₂ sequestered in underground aquifers.     

CO2SINK—From site characterisation and risk assessment to monitoring and verification: One year of operational experience with the field laboratory for CO2 storage at Ketzin, Germany

The CO₂SINK pilot project at Ketzin is aimed at a better understanding of geological CO₂ storage operation in a saline aquifer. The reservoir consists of fluvial deposits with average permeability ranging between 50 and 100 mDarcy. The main focus of CO₂SINK is developing and testing of monitoring and verification technologies. All wells, one for injection and two for observation, are equipped with smart casings (sensors behind casing, facing the rocks) containing a Distributed Temperature Sensing (DTS) and electrodes for Electrical Resistivity Tomography (ERT). The in-hole Gas Membrane Sensors (GMS) observed the arrival of tracers and CO₂ with high temporal resolution. Geophysical monitoring includes Moving Source Profiling (MSP), Vertical Seismic Profiling (VSP), crosshole, star and 4-D seismic experiments. Numerical models are benchmarked via the monitoring results indicating a sufficient match between observation and prediction, at least for the arrival of CO₂ at the first observation well. Downhole samples of brine showed changes in the fluid composition and biocenosis. First monitoring results indicate anisotropic flow of CO₂ coinciding with the “on-time” arrival of CO₂ at observation well one (Ktzi 200) and the later arrival at observation well two (Ktzi 202). A risk assessment was performed prior to the start of injection. After one year of operations about 18,000 t of CO₂ were injected safely.