Determination of Nitrogen Oxides in Auto Exhaust

A new procedure for determining nitrogen oxides in automobile exhaust has been developed. The new procedure was included in a Bureau of Mines comparative study that aimed at evaluating various widely used methods for determining NO_x in auto exhaust. The methods included in the evaluation study follow: (1) Static oxidation in tank (ST method). The method involves oxidation of NO in residence with O₂ in a stainless steel tank. (2) Bureau of Mines method (BM method). The method involves application of the ST procedure in exhaust samples from which the hydrocarbons have been removed by combustion over catalyst. (3) Chevron Research method (CR method), as described in the literature. (4) Phenoldisulfonic acid method (PDS method), as described in the literature. The principal objective of this study was to generate experimental evidence which would lead to defining an optimum procedure for converting NO, present in exhaust gas, into NO₂; this conversion is desired so that the total of NO + NO₂ can be determined quantitatively in the form of NO₂. In pursuing this objective, the procedures prescribed by the foregoing methods were comparatively tested. The results indicated that all four methods are subject to error, the extent of which depends on the conditions employed. The BM method was superior from the standpoint of accuracy because it was less affected by interferences due to hydrocarbon-NO₂ reactions.     

Control of Diesel Gaseous and Particulate Emissions with a Tube-Type Wet Electrostatic Precipitator

Abstract

In this study, experiments were performed with a bench-scale tube-type wet electrostatic precipitator (wESPs) to investigate its effectiveness for the removal of mass- and number-based diesel particulate matter (DPM), hydrocarbons (HCs), carbon monoxide (CO), and oxides of nitrogen (NO_x) from diesel exhaust emissions. The concentration of ozone (O₃) present in the exhaust that underwent a nonthermal plasma treatment process inside the wESP was also measured. A nonroad diesel generator operating at varying load conditions was used as a stationary diesel emission source. The DPM mass analysis was conducted by means of isokinetic sampling and the DPM mass concentration was determined by a gravimetric method. An electrical low-pressure impactor (ELPI) was used to quantify the DPM number concentration. The HC compounds, n-alkanes, and polycyclic aromatic hydrocarbons (PAHs) were collected on a moisture-free quartz filter together with a PUF/XAD/PUF cartridge and extracted in dichloromethane with sonication. Gas chromatography (GC)/mass spectroscopy (MS) was used to determine HC concentrations in the extracted solution. A calibrated gas combustion analyzer (Testo 350) and an O₃ analyzer were used for quantifying the inlet and outlet concentrations of CO and NO_x (nitric oxide [NO] + nitrogen dioxide [NO₂]), and O₃ in the diesel exhaust stream. The wESP was capable of removing approximately 67–86% of mass- and number-based DPM at a 100% exhaust volumetric flow rate generated from 0- to 75-kW engine loads. At 75-kW engine load, increasing gas residence time from approximately 0.1 to 0.4 sec led to a significant increase of DPM removal efficiency from approximately 67 to more than 90%. The removal of n-alkanes, 16 PAHs, and CO in the wESP ranged from 31 to 57% and 5 to 38%, respectively. The use of the wESP did not significantly affect NO_x concentration in diesel exhaust. The O₃ concentration in diesel exhaust was measured to be less than 1 ppm. The main mechanisms responsible for the removal of these pollutants from diesel exhaust are discussed.     

Identification of brake wear particles and derivation of a quantitative tracer for brake dust at a major road

Traffic-generated air pollutant emissions can be classified into exhaust and non-exhaust emissions. Increased attention is focussing on non-exhaust emissions as exhaust emissions are progressively limited by regulations. To characterise metal-rich emission from abrasion processes, size-segregated analysis of atmospheric aerosol particles sampled with micro-orifice uniform deposit impactors (MOUDI) in March 2007 in London was performed. The samples were collected at a roadside and a background site and were analysed for Al, Ba, Cu, Fe, Sb, Ti, V, Zn, Ca²⁺, K⁺, Mg²⁺, Na⁺, and NH₄⁺. Most components showed a clear roadside increment, which was evident as a higher mass concentration and a change in the size distribution. In particular, Fe, Cu, Ba, and Sb correlated highly, indicative of a common traffic-related source. Using complementary information on the fleet composition, vehicle number and average speed, the brake wear emission was calculated using the EMEP/CORINAIR emission database. The total PM₁₀ and barium emission of the traffic was determined by ratio to NO_x whose source strength was estimated from published emission factors. Barium was found to comprise 1.1% of brake wear (PM₁₀) particles from the traffic fleet as a whole, allowing its use as a quantitative tracer of brake wear emissions at other traffic-influenced sites.     

HCI in Rocket Exhaust Clouds: Atmospheric Dispersion,Acid Aerosol Characteristics,and Acid Rain Deposition

NASA is examining Space Shuttle launch impacts. Solid rocket exhaust includes ?60 tons HCL and ?87 tons alumina particles emitted below 2.5 km, of which 50-80% forms an altitude stabilized exhaust cloud (EC). Several 60% smaller Titan-Ill EC were sampled by aircraft for this study. Three distinct features are presented: (a) An analysis of HCL (gaseous plus aqueous) data traces. Total range of peak HCL was 25-0.5 ppm (3-300 min) for 8 EC. Power-law decays of peak HCL applied. Calculated HCL dispersions for 7 standard meteorologies are also shown, (b) An analysis of simultaneous HCL (g), HCL (g + aq) data for 2 EC. Vapor-liquid HCL/H₂O equilibria were calculated for a flat surface aqueous aerosol. HCL partitioning varied with EC dilution and H₂O content. HCL (aq) and aqueous mass fraction maximized early at >3 molal and >0.1 mg/g air. Calculated H₂O (g + aq) compared favorably with independent EC measurements, (c) An analysis of wet deposition after EC interception at ?30 min by a convective storm. A 28 km² acid chloride (1 < pH < 3) footprint was defined. In conclusion, (a) HCL dispersion in large EC tends to follow power-law decay, but HCL concentration may vary widely (100 times after 1 h) with meteorology, (b) HCL (g/aq) and H₂O (g/aq) partitioning is consistent with equilibrated acid aerosol compositions, and (c) localized deposition of highly acidic rain may occur sometimes.     

Monte Carlo simulation of nitrogen oxides dispersion from a vehicular exhaust plume and its sensitivity studies

The pollutant dispersion behavior from the vehicular exhaust plume has a direct impact on human health, particularly to the drivers, bicyclists, motorcyclists, pedestrians, people working nearby and vehicle passengers. A two-dimensional pollutant dispersion numerical model was developed based on the joint-scalar probability density function (PDF) approach coupled with a k–ε turbulence model to simulate the initial dispersion process of nitrogen oxides, temperature and flow velocity distributions from a vehicular exhaust plume. A Monte Carlo algorithm was used to solve the PDF transport equations in order to obtain the dispersion distribution of nitrogen oxides concentration. The model was then validated by a series of sensitivity experimental studies in order to assess the effects of vehicular exhaust tailpipe velocities, wind speeds and chemistry on the initial dispersion of NO and NO₂ mass concentrations from the vehicular exhaust plume. The results show that the mass concentrations of nitrogen oxides decrease along the centerline of the vehicular exhaust plume in the downstream distance. The dispersion process can be enhanced when the vehicular exhaust tailpipe velocity is much larger than the wind speed. The oxidation reaction of NO plays an important role when the wind speed is large and the vehicular exhaust exit velocity is small, which leads to chemical reduction of NO, and the formation and accumulation of NO₂ in the exhaust plume. It is also found that the effect of vehicular exhaust-induced turbulence in the vicinity of the exhaust tailpipe exit is more dominant than the effect of wind turbulence, while the wind turbulence gradually shows a significant role for the dispersion of nitrogen oxides along with the development of exhaust plume. The range of dispersion of nitrogen oxides in the radial direction is increased along with the development of vehicular exhaust plume.     

Application of CALINE4 to roadside NO/NO2 transformations

The CALINE4 roadway dispersion model has been applied to concentrations of NO_x and NO₂ measured near Gandy Boulevard in Tampa, FL (USA) during May 2002. A NO_x emission factor of 0.86 gr mi⁻¹ was estimated by treating NO+NO₂ (NO_x) as a conserved species and minimizing the differences between measured and calculated NO_x concentrations. This emission factor was then used to calculate NO₂ concentrations using the NO/NO₂ transformation reactions built into CALINE4. A comparison of measured and calculated NO₂ concentrations indicates that for ambient O₃ concentrations less than 40 ppb the model under-predicts the chemical transformation of NO. The enhanced transformation of NO may be due to reactions of NO with oxidants such as peroxy radicals that are present either in the atmosphere or in vehicle exhaust.     

Ship emissions and their externalities for Greece

The existing and emerging international and European policy framework for the reduction of ship exhaust emissions dictates the need to produce reliable national, regional and global inventories in order to monitor emission trends and consequently provide the necessary support for future policy making. Furthermore, the inventories of ship exhaust emissions constitute the basis upon which their external costs are estimated in an attempt to highlight the economic burden they impose upon the society and facilitate the cost–benefit analysis of the proposed emission abatement technologies, operational measures and market-based instruments prior to their implementation.The case of Greece is of particular interest mainly because the dense ship traffic within the Greek seas directly imposes the impact of its exhaust emission pollutants (NO_x, SO₂ and PM) upon the highly populated, physically sensitive and culturally precious Greek coastline, as well as upon the land and seas of Greece in general, whereas the contribution of Greece in the global CO₂ inventory at a time of climatic change awareness cannot be ignored. In this context, this paper presents the contribution of Greece in ship exhaust emissions of CO₂, NO_x, SO₂ and PM from domestic and international shipping over the last 25 years (1984–2008), utilizing the fuel-based (fuel sales) emission methodology. Furthermore, the ship exhaust emissions generated within the Greek seas and their externalities are estimated for the year 2008, through utilizing the fuel-based (fuel sales) approach for domestic shipping and the activity-based (ship traffic) approach for international shipping.On this basis, it was found that during the 1984 to 2008 period the fuel-based (fuel sales) ship emission inventory for Greece increased at an average annual rate of 2.85%. In 2008, the CO₂, NO_x, SO₂ and PM emissions reached 12.9 million tons (of which 12.4 million tons of CO₂) and their externalities were found to be around 3.1 billion euro. With regard to shipping within the Greek seas, the utilization of the fuel-based (fuel sales) analysis for domestic shipping and the activity-based (ship traffic) analysis for international shipping shows that the ship-generated emissions reached 7.4 million tons (of which 7 million tons of CO₂) and their externalities were estimated at 2.95 billion euro. Finally, the internalization of external costs for domestic shipping was found to produce an increase of 12.96 and 2.71 euro per passenger and transported ton, respectively.     

Emissions profile from new and in-use handheld, 2-stroke engines

The objective of this study was to characterize exhaust emissions from a series of handheld, 2-stroke small engines. A total of 23 new and used engines from model years 1981–2003 were studied; these engines spanned three phases of emission control (pre-control, phase-1, phase-2). Measured emissions included carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NO_x), hydrocarbons (HC), fine particulate matter (PM_2.5), and sulfur dioxide (SO₂). Emissions reductions in CO (78%) and HC (52%) were significant between pre-control and phase-2 engines. These reductions can be attributed to improvements in engine design, reduced scavenging losses, and implementation of catalytic exhaust control. Total hydrocarbon emissions were strongly correlated with fuel consumption rates, indicating varying degrees of scavenging losses during the intake/exhaust stroke. The use of a reformulated gasoline containing 10% ethanol resulted in a 15% decrease in HC and a 29% decrease in CO emissions, on average. Increasing oil content of 2-stroke engine fuels results in a substantial increase of PM_2.5 emissions as well as smaller increases in HC and CO emissions. Results from this study enhance existing emission inventories and appear to validate predicted improvements to ambient air quality through implementation of new phase-2 handheld emission standards.     

Effect of Gasoline Formulation on the Formation of Photosmog: A Box Model Study

Abstract

Based on exhaust gas analyses from the combustion of five different types of gasoline in a passenger car operated on a chassis dynamometer, box model simulations of the irradiation of exhaust/NO_x /air mixtures using an established chemical mechanism for a standardized photo-smog scenario were performed. The fuel matrix used covered wide fractional ranges for paraffinic, olefinic, and aromatic hydrocarbons. Two fuels also contained methyl tertiary butyl ether (MTBE). The different O₃ profiles calculated for each run were compared and interpreted. The O₃ levels obtained were strongly influenced by the exhaust gas concentrations of aromatic and olefinic hydro-carbons. The higher exhaust content of these compounds caused higher O₃ production in the smog system investigated. The conclusion of the present study is that the composition of gasoline cannot be taken directly for the estimation of the emissions’ O₃ creation potential from its combustion. Variation of the dilution in the different calculations showed evidence for an additional influence of transport effects. Accordingly, further detailed exhaust gas analyses followed by more complex modeling studies are necessary for a proper characterization of the relationship between fuel blend and gasoline combustion products.     

The impact of NOx,CO and VOC emissions on the air quality of Zurich airport

To study the impact of emissions at an airport on local air quality, a measurement campaign at the Zurich airport was performed from 30 June 2004 to 15 July 2004. Measurements of NO, NO₂, CO and CO₂ were conducted with open path devices to determine real in-use emission indices of aircraft during idling. Additionally, air samples were taken to analyse the mixing ratios of volatile organic compounds (VOC). Temporal variations of VOC mixing ratios on the airport were investigated, while other air samples were taken in the plume of an aircraft during engine ignition. CO concentrations in the vicinity of the terminals were found to be highly dependent on aircraft movement, whereas NO concentrations were dominated by emissions from ground support vehicles. The measured emission indices for aircraft showed a strong dependence upon engine type. Our work also revealed differences from emission indices published in the emission data base of the International Civil Aviation Organisation. Among the VOC, reactive C₂–C₃ alkenes were found in significant amounts in the exhaust of an engine compared to ambient levels. Also, isoprene, a VOC commonly associated with biogenic emissions, was found in the exhaust, however it was not detected in refuelling emissions. The benzene to toluene ratio was used to discriminate exhaust from refuelling emission. In refuelling emissions, a ratio well below 1 was found, while for exhaust this ratio was usually about 1.7.     

Simultaneous removal of NOx,SO2, and Hg from flue gas in FGD absorber with oxidant injection (NaClO2)– full-scale investigation

ABSTRACT

This article presents the results of an industrial-scale study (on 400 MW_e lignite fired unit) of simultaneous NO_x, SO₂, and Hg^T removal in FGD absorber with oxidant injection (NaClO₂) into flue gas. It was confirmed that the injection of sodium chlorite upstream the FGD (Flue Gas Desulfurization) absorber oxidize NO to NO₂, Hg⁰ to Hg²⁺, and enhancing NO_x and Hg^T removal efficiency from exhaust gas in FGD absorber. Mercury removal efficiency grows with the rise of degree of oxidation NO to NO₂ and was limited by the phenomenon of re-emission. For NO_x removal the most critical parameters is slurry pH and temperature. There was no negative effect on sulfur dioxide removal efficiency caused by oxidant injection in tested FGD absorber. Based on the data provided, NO_x and Hg^T emissions can be reduced by adjusting the FGD absorber operating parameters combined with oxidant injection.     

Source apportionment of PM2.5 at two Seattle chemical speciation sites

ABSTRACT

Positive Matrix Factorization analysis of PM_2.5 chemical speciation data collected from 2015–2017 at Washington State Department of Ecology’s urban NCore (Beacon Hill) and near-road (10th and Weller) sites found similar PM_2.5 sources at both sites. Identified factors were associated with gasoline exhaust, diesel exhaust, aged and fresh sea salt, crustal, nitrate-rich, sulfur-rich, unidentified urban, zinc-rich, residual fuel oil, and wood smoke. Factors associated with vehicle emissions were the highest contributing sources at both sites. Gasoline exhaust emissions comprised 26% and 21% of identified sources at Beacon Hill and 10th and Weller, respectively. Diesel exhaust emissions comprised 29% of identified sources at 10th and Weller but only 3% of identified sources at Beacon Hill. Correlation of the diesel exhaust factor with measured concentrations of black carbon and nitrogen oxides at 10th and Weller suggests a method to predict PM_2.5 from diesel exhaust without a full chemical speciation analysis. While most PM_2.5 sources exhibit minimal change over time, primary PM_2.5 from gasoline emissions is increasing on average 0.18 µg m^?3 per year in Seattle.     

Emission factor of exhaust gas constituents during the pyrolysis of zinc chloride immersed biosolid

Pyrolysis enables ZnCl₂ immersed biosolid to be reused, but some hazardous air pollutants are emitted during this process. Physical characteristics of biosolid adsorbents were investigated in this work. In addition, the constituents of pyrolytic exhaust were determined to evaluate the exhaust characteristics. Results indicated that the pyrolytic temperature was higher than 500 °C, the specific surface area was >900 m²/g, and the total pore volume was as much as 0.8 cm³/g at 600 °C. For non-ZnCl₂ immersed biosolid pyrolytic exhaust, VOC emission factors increased from 0.677 to 3.170 mg-VOCs/g-biosolid with the pyrolytic temperature increase from 400 to 700 °C, and chlorinated VOCs and oxygenated VOCs were the dominant fraction of VOC groups. VOC emission factors increased about three to seven times, ranging from 1.813 to 21.448 mg/g for pyrolytic temperatures at 400–700 °C, corresponding to the mass ratio of ZnCl₂ and biosolid ranging from 0.25–2.5.     

Responses of herbaceous plants to urban air pollution: Effects on growth, phenology and leaf surface characteristics

Vehicle exhaust emissions are a dominant feature of urban environments and are widely believed to have detrimental effects on plants. The effects of diesel exhaust emissions on 12 herbaceous species were studied with respect to growth, flower development, leaf senescence and leaf surface wax characteristics. A diesel generator was used to produce concentrations of nitrogen oxides (NO_x) representative of urban conditions, in solardome chambers. Annual mean NO_x concentrations ranged from 77 nl l^−l to 98 nl l⁻¹, with NO:NO₂ ratios of 1.4-2.2, providing a good experimental simulation of polluted roadside environments. Pollutant exposure resulted in species-specific changes in growth and phenology, with a consistent trend for accelerated senescence and delayed flowering. Leaf surface characteristics were also affected; contact angle measurements indicated changes in surface wax structure following pollutant exposure. The study demonstrated clearly the potential for realistic levels of vehicle exhaust pollution to have direct adverse effects on urban vegetation.     

Analysis of NO,NO2, O3 and NOx concentrations measured at a green area of Buenos Aires City during wintertime

We analyse the air quality data measured at a green area of Buenos Aires City (Argentina) during 38 days in winter. We study the relationships between ambient concentrations of nitric oxide (NO), nitrogen dioxide (NO₂), ozone (O₃) and nitrogen oxides (NO_x=NO+NO₂). The variation of the level of oxidant (OX=O₃+NO₂) with the NO_x is obtained. It can be seen that the level of OX at a given location is made up of two contributions: one independent and another dependent on the NO_x concentration. The first one can be considered as a regional contribution, equivalent to the background O₃ concentration and the second one as a local contribution that depends on the level of primary pollution. Local oxidant sources may include direct NO₂ emissions, the reaction of NO with O₂ at high-NO_x levels, and the emission of species that promote the conversion of NO to NO₂. The final category of emissions may include the nitrous acid (HONO) that is emitted directly in vehicle exhaust. Finally, we present a diurnal variation of the local as well as regional contributions and the dependence of the last one on wind direction.     

Product Guide/1982

Abstract

An efficient venturi scrubber system making use of heterogeneous nucleation and condensational growth of particles was designed and tested to remove fine particles from the exhaust of a local scrubber where residual SiH₄ gas was abated and lots of fine SiO₂ particles were generated. In front of the venturi scrubber, normal-temperature fine-water mist mixes with high-temperature exhaust gas to cool it to the saturation temperature, allowing submicron particles to grow into micron sizes. The grown particles are then scrubbed efficiently in the venturi scrubber. Test results show that the present venturi scrubber system is effective for removing submicron particles. For SiO₂ particles greater than 0.1 μm, the removal efficiency is greater than 80–90%, depending on particle concentration. The corresponding pressure drop is relatively low. For example, the pressure drop of the venturi scrubber is ～15.4 ± 2.4 cm H₂O when the liquid-to-gas ratio is 1.50 L/m³. A theoretical calculation has been conducted to simulate particle growth process and the removal efficiency of the venturi scrubber. The theoretical results agree with the experimental data reasonably well when SiO₂ particle diameter is greater than 0.1 μm.     

活性炭吸附和脱附-等离子体氧化净化有机废气的研究

根据滑动弧放电等离子体适于降解高浓度有机物废气的特性,结合活性炭吸附法,提出了吸附器的吸附浓缩和热脱附-等离子体氧化净化有机废气的方法。在活性炭吸附过程中,最初2 h内甲苯净化率达到100%,随着时间的增加净化率下降;在热脱附滑动弧放电等离子体净化过程中,甲苯降解效率最高为97.3%。将滑动弧放电等离子体反应器出口气相产物收集进行FT-IR检测,发现放电后有CO2、CO、H2O和NO2产生,并分析了甲苯的降解机理。     

Dilution and aerosol dynamics within a diesel car exhaust plume—CFD simulations of on-road measurement conditions

Vehicle particle emissions are studied extensively because of their health effects, contribution to ambient PM levels and possible impact on climate. The aim of this work was to obtain a better understanding of secondary particle formation and growth in a diluting vehicle exhaust plume using 3-d information of simulations together with measurements. Detailed coupled computational fluid dynamics (CFD) and aerosol dynamics simulations have been conducted for H₂SO₄–H₂O and soot particles based on measurements within a vehicle exhaust plume under real conditions on public roads.Turbulent diffusion of soot and nucleation particles is responsible for the measured decrease of number concentrations within the diesel car exhaust plume and decreases coagulation rates. Particle size distribution measurements at 0.45 and 0.9 m distance to the tailpipe indicate a consistent soot mode (particle diameter D_p∼50 nm) at variable operating conditions. Soot mode number concentrations reached up to 10¹³ m⁻³ depending on operating conditions and mixing.For nucleation particles the simulations showed a strong sensitivity to the spatial dilution pattern, related cooling and exhaust H₂SO_4(g). The highest simulated nucleation rates were about 0.05–0.1 m from the axis of the plume. The simulated particle number concentration pattern is in approximate accordance with measured concentrations, along the jet centreline and 0.45 and 0.9 m from the tailpipe. Although the test car was run with ultralow sulphur fuel, high nucleation particle (D_p⩽15 nm) concentrations (>10¹³ m⁻³) were measured under driving conditions of strong acceleration or the combination of high vehicle speed (>140 km h⁻¹) and high engine rotational speed (>3800 revolutions per minute (rpm)).Strong mixing and cooling caused rapid nucleation immediately behind the tailpipe, so that the highest particle number concentrations were recorded at a distance, x=0.45 m behind the tailpipe. The simulated growth of H₂SO₄–H₂O nucleation particles was unrealistically low compared with measurements. The possible role of low and semi-volatile organic components on the growth processes is discussed. Simulations for simplified H₂SO₄–H₂O–octane–gasoil aerosol resulted in sufficient growth of nucleation particles.     

Product Guide/1970

Abstract

In Mexico City, the use and composition of fuels determine that carbon monoxide (CO) comes mostly from mobile sources, and sulfur dioxide (SO₂) from fixed and mobile sources. By simultaneously measuring hydrocarbons (HC), CO, and SO₂ in the atmosphere of Mexico City, the relative amounts coming from different sources can be estimated. Assuming that some HC are emitted proportionally to CO emissions, we can establish that [HC]₁= m1? [CO], where the proportionality constant ml corresponds to the ratio of emissions factor for HC and CO in mobile sources. Similarly for fuels containing sulfur, it can be assumed that [HC]₂ = m2 ? [SO₂]. In this way, the total HC are [HC]_total=[HC]₀+ ml ? [CO]+ m2 ? [SO₂], where [HC]₀ corresponds mainly to other sources like solvent evaporation, gas consumption, and natural emissions. In this way, it can be estimated that in Mexico City 75% of average HC comes from mobile sources, 5% from sulfur-related sources, and 19% from natural sources and solvent evaporation. Compared with the HC/CO ratio measured in the exhaust pipe of vehicles, we estimated that 70% of HC emitted from mobile sources are evaporative losses, and only 30% come through the exhaust system.     

Fans and Fan Systems

Abstract

There is a need for robust and accurate techniques for the measurement of ammonia (NH₃) and other atmospheric pollutant emissions from poultry production facilities. Reasonable estimates of NH₃ emission rate (ER) from poultry facilities are needed to guide discussions about the industry’s impact on local and regional air quality. The design of these facilities features numerous emission points and results in emission characteristics of relatively low concentrations and exhaust flow rates that vary diurnally, seasonally, and with bird age over a considerable range. These factors combine to render conventional emissions monitoring approaches difficult to apply. Access to these facilities is also often restricted for biosecurity reasons. The three objectives of this study were (1) to compare three methods for measuring exhaust NH₃ concentrations and thus ERs, (2) to compare ventilation rates using in situ measured fan characteristics versus using manufacturer sourced fan curves, and (3) to examine limitations of the alternative measurement technologies. In this study, two open-path monitoring systems operating outside of the buildings were compared with a portable monitoring system sampling upstream of a primary exhaust fan. The position of the open-path systems relative to the exhaust fans, measurement strategy adopted, and weather conditions significantly influenced the quality of data collected when compared with the internally located, portable monitoring system. Calculation of exhaust airflow from the facility had a large effect on calculated emissions and assuming that the installed fans performed as per published performance characteristics potentially overestimated emissions by 13.6–26.8%. The open-path measurement systems showed promise for being able to obtain ER measurements with minimal access to the house, although the availability of individual fan characteristics markedly improved the calculated ER accuracy. However, substantial operator skill and experience and favorable weather conditions were required to obtain good quality results.