蜂窝煤燃烧氟污染的控制

以碳酸钙为固氟添加剂,以炉渣及粉煤灰等低氟材料取代全部或部分粘土作为粘结剂来制作蜂窝煤,进行了燃煤降氟的试验研究.结果表明,添加碳酸钙能有效降低蜂窝煤燃烧时候的氟排放,当煤:粘土:CaCO3的质量比为70:17:13时,碳酸钙的固氟效果最佳,氟的排放率可降低64.1%.以炉渣为粘结剂制作蜂窝煤能够显著降低燃烧时向外界排放的氟化物量,当煤:炉渣:CaCO3为80:8:12时,蜂窝煤燃烧排氟量较小且趋于稳定.已拌有一定剂量粉煤灰粘结剂的煤中添加15%的粘土后碳酸钙的固氟效果明显改善,当煤:粘土:粉煤灰:CaCO3为70:15:9:6时固氟效果最佳,此时蜂窝煤氟逸出率仅为18.2%,氟的减排率达到77.9%,显著优于未添加粘土时碳酸钙的固氟效果,蜂窝煤添加碳酸钙固氟剂进行高效固氟时,需同时适当增加粉煤灰加入量,以稳定固氟剂的高温固氟效果.     

异噻唑啉酮耦合氧化钙对污泥压滤脱水及燃烧热值的影响

通过正交实验考察了异噻唑啉酮耦合氧化钙对压滤污泥含水率、燃烧热值、Zeta电位和泥饼含硫量的影响,结果表明,各因素对污泥含水率影响的大小顺序依次为:氧化钙投加量、压强、压滤时间、异噻唑啉酮投加量;各因素对污泥燃烧热值影响的大小顺序依次为:氧化钙投加量、压滤时间、异噻唑啉酮投加量和压强。异噻唑啉酮投加量为5.6 mg/g TSS,氧化钙投加量为120 mg/g TSS,压强为0.40 MPa,压滤时间为1 h条件下,污泥含水率为55.5%,105℃烘干泥饼的热值为10 702 J/g,Zeta电位值为-30.082 mV,泥饼含硫量为0.408%。此时污泥含水率较低,热值较高,含硫量较低,有利于污泥的焚烧处理。     

MBR出水氯、紫外、臭氧单独与组合消毒

采用氯、紫外和臭氧单独与2种组合工艺对MBR工艺中试出水进行了消毒实验,研究了不同消毒方式对指示性微生物的去除效果以及消毒副产物三卤甲烷(THMs)生成量随有效氯投加量的变化。结果表明,组合工艺消毒效果明显优于单独消毒效果,紫外剂量为25 mJ/cm2与有效氯投加量为3 mg/L的紫外与氯组合、臭氧投加量为6 mg/L与有效氯投加量为4 mg/L的臭氧与氯组合2种工艺消毒后出水中的总大肠菌群指标均满足《污水再生利用城市杂用水水质》(GB/T 18920-2002)的要求。THMs生成量随着有效氯投加量的增加而增加。相对紫外与氯组合消毒,臭氧与氯组合消毒可以大幅度降低THMs生成量,有效氯投加量为4 mg/L时,THMs生成浓度为14.11μg/L,比氯单独消毒过程降低了37.19%。     

加盐蒸馏回收盐酸和混凝剂制备技术资源化利用盐酸酸洗废液

为了实现钢材酸洗废液的资源化,能够同时回收盐酸和铁盐,提出了加盐蒸馏回收盐酸与蒸馏母液制备聚铁混凝剂两段组合工艺相结合的技术。实验对质量浓度为9.28%的实际盐酸废液进行了研究,考察了添加盐的种类、盐的投加量和蒸馏量等因素对再生盐酸回收效果和聚铁混凝剂溶液混凝效果的影响。研究表明,氯盐可以明显改变氯化氢、水的相对挥发度,当CaCl2投加量为1 mol/L,体积蒸馏量在30%时,为此工艺的最佳条件。在此工艺条件下,再生盐酸质量浓度约22.3%;蒸馏母液制备得到的聚铁混凝剂溶液应用实验表明,对印染废水脱色效果良好。此工艺不仅实现了酸洗废液中残酸和铁离子的资源化利用,而且达到酸洗废液的零排放。     

过量生石灰对污泥含水率和有机物含量的影响

为了研究生石灰(氧化钙,CaO)处理活性污泥对污泥含水率和有机物含量的影响,通过向南京某城市污水处理厂出厂污泥投加过量CaO进行脱水实验,测定投加CaO后污泥的含水率;烘干后的脱水污泥进行热重实验,研究CaO投加量对污泥中有机组分含量的影响.脱水实验表明:随着CaO与污泥质量比的增大,污泥含水率迅速减小,当质量比达到1.5时,污泥达到完全脱水;投加过量CaO的脱水污泥呈干燥的粉末状,粒度均匀,可作为水泥生产的辅料。热重实验表明:投加CaO后单位干泥失重百分比随CaO与污泥质量比增大而逐渐减小,向污泥中投加CaO有利于污泥中有机组分的释放和去除,实现污泥的稳定化。     

热化学清洗法洗涤油泥-回收石油的工艺条件研究

以辽河油田落地油泥为样品,采用热化学清洗法洗涤油泥,净化土壤,回收石油,并获取工程所需的必要参数.通过筛选、复配,确定十二烷基苯磺酸钠(LAS):NazSiO3=1:2(质量比)为最佳清洗剂配比.考察了清洗温度、清洗液pH、液固比(即清洗剂与落地油泥的质量比)和清洗剂投加量等因素对清洗效率的影响,通过正交实验优化工艺参数,实验表明,当清洗时间为30min、清洗温度为75℃、搅拌器转速为200 r/min、液固比为8:1、清洗液pH为11、LAS Na2SiO3投加量为2.8 g/L时,含油率为21.2%(质量分数)的落地油泥样品经一级清洗,油泥残油率降为0.8%(质量分数,下同);经二级清洗,油泥残油率降为0.3%.清洗后,石油浮于水面,无明显乳化,易于分离.     

氯胺消毒对三卤甲烷生成影响因素研究

采用腐殖酸模拟天然水体中消毒副产物前体物,探求了氯氨比、氯胺投加量、总有机碳(TOC)浓度和Br-浓度在氯胺消毒过程中对消毒副产物——三卤甲烷(THMs)生成量的影响。结果表明:(1)随着氯氨比的降低,THMs及各组分的生成量显著减少。(2)THMs的生成量均随着氯胺投加量的增加而增加,且都呈现出了良好的线性关系。当氯胺投加量大于7.0mg/L时,氯代卤化物成了优势产物。(3)随着TOC浓度的增加,THMs生成量增加,且具有一定的线性关系;三氯甲烷和一溴二氯甲烷生成量均增加,氯氨比为3∶1(质量比,下同)时三氯甲烷和一溴二氯甲烷生成量增加了9.86、7.80μg/L,氯氨比为5∶1时则分别增加了15.21、13.62μg/L;三溴甲烷和二溴一氯甲烷生成量均呈现先增加后减少的趋势。(4)随着Br-浓度的增加,THMs、一溴二氯甲烷、二溴一氯甲烷和三溴甲烷生成量均增加,三氯甲烷生成量减少。溴化物的存在会促进THMs的产生。     

紫外光助O3、H2O2氧化降解炼油废碱水的可行性实验

炼油高浓度有机废碱水是石化行业中很难降解的废水.本实验用光化学氧化技术对其进行了降解研究,比较了紫外光/空气、紫外光/O3、紫外光/空气/H2O2系统的处理效果.结果表明,光化学氧化技术降解此废水是可行的,紫外光可使废水中COD、油、酚的降解率明显提高.当废水中O3的投加量每小时为22 mg/L,或H2O2投加量为1%/L时,UV/O3法与UV/空气/H2O2法的降解效果相近.同时,通过控制O3浓度或H2O2的投加量等条件,可使废水中COD、油、酚和硫化物降解到地方污染物二级排放标准.     

改性氧化铝微波诱导催化氧化处理高浓度苯酚废水的研究

采用微波诱导催化氧化技术，以改性氧化铝为催化剂，对高浓度模拟苯酚废水进行氧化处理。考察了微波功率、催化剂投加量、H202投加量、废水pH值和微波反应时间等因素对苯酚去除效果的影响。实验结果表明，处理30mL质量浓度为1 100mg/L的苯酚模拟废水，在微波功率500W，催化剂加入量1 g(液固比30∶1)，30％双氧水...     

三氯异氰尿酸在窖水中的余氯衰减规律及消毒效果

为保持集雨窖水水质,提高饮用水安全性,采用向窖水中投加三氯异氰尿酸(trichloroisocyanuric acid,TCCA)的消毒方法,检测主体水的余氯衰减规律和微生物的变化情况,重点研究了消毒剂投加量、温度及pH等因素的影响。实验结果表明:余氯衰减过程符合一级动力学模型;随初始氯投加量的增大,水中余氯衰减量增大,余氯衰减系数减小且与初始投加量的倒数成线性正相关;随水中有机物等反应物浓度的降低,余氯衰减量减少,余氯衰减系数减小;随温度的升高,余氯衰减量增大,衰减系数增大;随pH的增大,余氯衰减量减少,衰减系数减小;水中菌落总数的灭活率随消毒剂投加量的增加而增大。当消毒剂浓度为1.5～2.5 mg·L~(-1)时,在60 min内可完成对菌落总数99.0%的灭活;当消毒剂浓度大于2.5 mg·L~(-1)时,在30 min内可完成对菌落总数99.9%的灭活。在pH为6～9时,pH越小,消毒效果越好;在10～30℃时,温度越高,消毒效果越好;水中氨氮存在时,氯胺的生成会减弱短期消毒效果。与传统氯制消毒剂相比,TCCA在窖水消毒方面有较好的应用前景。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.