复合改性膨润土对氨氮废水的吸附及脱附

为了研究氨氮的吸附及脱附机理,使用了SDS(十二烷基硫酸钠)和AlCl_3·6H_2O(六水合三氯化铝)复合改性制备的改性膨润土对氨氮废水进行吸附及脱附性能研究。首先通过改性膨润土对含氨氮废水的吸附动力学实验和等温吸附实验研究膨润土的吸附过程,再利用KCl作为脱附剂,对吸附饱和的膨润土进行脱附再生,使用再生的脱附膨润土复合材料进行吸附实验。实验表明,动力学实验中,准二级动力学方程能够更好的模拟氨氮废水的吸附过程,Langmuir模型和Freundlich模型均能拟合氨氮的吸附过程,但综合评价,选用Freundlich等温方程式。脱附剂KCl溶液pH为3、浓度为550 mg·L~(-1)时,搅拌速度为250 r·min~(-1),室温下搅拌20 min,吸附饱和膨润土能够很好地脱附,脱附率达到75.21%。再生的复合膨润土材料对氨氮的去除率为62.83%。     

八羟基喹啉改性膨润土预处理养殖废水

以八羟基喹啉为改性剂,天然膨润土为原料,制备一种新型吸附剂,并将其应用于养殖废水的预处理中。确定了改性膨润土的最佳制备条件:土液比为4 g/L,改性剂浓度为0.3 g/L,改性时间为50 min,改性温度为50℃。并以扫描电镜方法对改性膨润土行进表征:八羟基喹啉已经有效进入层间,改变了膨润土的性状,提高了吸附效果。优化了改性膨润土处理养殖废水的工艺条件:投土量为1 g/L,pH为4,搅拌时间为30 min,搅拌速度为350 r/min,沉淀时间为40 min。在此优化条件下,改性膨润土对养殖废水的COD去除率最高可达79.18%,且吸附动力学结果满足二级动力学模型。     

电气石对恩诺沙星的吸附特性

采用天然铁电气石作为吸附剂去除水中的恩诺沙星,考察了p H值、干扰离子对吸附性能的影响,并探讨了吸附热力学及动力学特性。结果表明:p H为5的条件下,吸附量最大,为7.13 mg·g~(-1);ΔG0且ΔH0表明吸附是自发进行的吸热反应,ΔH=2.048 k J·mol~(-1)(20 k J·mol~(-1))说明吸附为物理吸附。等温吸附曲线拟合中,Freundlich模型拟合效果较好。电气石对恩诺沙星的吸附过程符合拟二级动力学。脱附实验表明,电气石具有较好的脱附再生性能,脱附率可达99%。初始p H为5时,较高浓度的Cu~(2+)和Zn~(2+)对恩诺沙星的吸附均有抑制作用,Cu~(2+)的抑制作用明显高于Zn~(2+),且干扰离子浓度越高抑制作用越强;p H为7时,低浓度的干扰离子能够促进恩诺沙星的吸附。     

零价铁复合有机膨润土处理染料废水的研究

针对目前印染废水处理现状及膨润土在水处理中回收困难等问题,提出将零价铁复合到有机膨润土中制成零价铁复合有机膨润土(ZVI-OB),以达到高效吸附并降解污染物的目的。以染料废水(Orange II) 作为研究对象,考察了废水中染料的初始浓度、pH以及吸附时间对ZVI-OB去除染料效率的影响,并研究了吸附后降解过程中时间和pH对污染物降解的影响以及降解前后膨润土层结构的变化。研究结果表明,ZVI-OB相对于CTMAB改性的有机膨润土而言,其吸附量有所降低,但ZVI-OB在吸附污染物之后能有效降解有机物。ZVI-OB在饱和吸附Orange II后经催化氧化,总有机碳含量降低为原来的19%,可以重复利用。     

负载壳聚糖膨润土的制备及其吸附性能的影响

以天然膨润土和壳聚糖为原料,制得一种新型水处理剂——负载壳聚糖膨润土,研究了制备条件对酸性大红印染废水处理效果的影响。实验表明,当壳聚糖的浓度为30 g/L、膨润土质量与壳聚糖溶液体积之比为0.7、浸泡时间80 min、微烘时间15 min时,壳聚糖改性膨润土对酸性大红印染废水的脱色率可达97%。对改性土进行比表面积测定、电镜扫描及X-射线衍射等结构特性分析,证明壳聚糖的引入改变了膨润土在水中的分散状态,增强了其对污染物的吸附和离子交换能力。     

改性粉煤灰及其处理废水的机理

应用正交设计的基本理论,研究了PDMDAAC(聚二甲基二烯丙基氯化铵)改性粉煤灰的最佳条件,并将改性粉煤灰用于模拟印染废水的处理,探索了改性粉煤灰处理废水的机理。结果表明,在原PDMDAAC的pH下．控制PDMDAAC的浓度为40g／L,恒温30℃．反应1h为最佳改性工艺,改性粉煤灰处理废水的机理以吸附电中和为主。     

活性炭纤维吸附废水中对硝基苯酚及其脱附研究

采用新型高效吸附剂--活性炭纤维吸附废水中对硝基苯酚,对其吸附和脱附影响因素进行了较详细的研究,确定了最佳工艺参数,并对动态吸附-脱附进行了稳定性实验.在最佳的吸附条件下,装填4 g活性炭纤维可处理含对硝基苯酚1000 mg/L的废水1400 mL,出水对硝基苯酚浓度＜2 mg/L,达到国家综合污水一级排放标准,活性炭纤维有效吸附量可达349.87 mg/g.在最佳脱附条件下,脱附率＞99%,并可从高浓度脱附液中回收对硝基苯酚.稳定性实验表明,吸附-脱附性能稳定,采用活性炭纤维吸附处理对硝基苯酚废水是一种行之有效的处理方法.     

活性炭纤维吸附废水中对硝基苯酚及其脱附研究

采用新型高效吸附剂——活性炭纤维吸附废水中对硝基苯酚，对其吸附和脱附影响因素进行了较详细的研究，确定了最佳工艺参数，并对动态吸附一脱附进行了稳定性实验。在最佳的吸附条件下，装填4g活性炭纤维可处理含对硝基苯酚1000mg/L的废水1400mL，出水对硝基苯酚浓度〈2mg／L，达到国家综合污水一级排放标准，活性炭纤维有效吸附量可达349．87mg／g。在最佳脱附条件下，脱附率〉99％，并可从高浓度脱附液中回收对硝基苯酚。稳定性实验表明，吸附-脱附性能稳定，采用活性炭纤维吸附处理对硝基苯酚废水是一种行之有效的处理方法。     

吡啶改性膨润土对直接耐晒翠蓝染料废水脱色性能研究

为了解决日益严重的水污染问题,用吡啶作改性剂,对膨润土进行有机改性,制得一种新型水处理剂,用于直接耐晒翠蓝染料废水的处理。研究了处理废水的最佳工艺条件。结果表明,投土量为10g／L,pH=3．5,搅拌速度为175r／min,搅拌时间25rain,离心时间为2min,吡啶改性土对直接耐晒翠蓝染料废水的脱色率可达80％。改性土对直接耐晒翠蓝的吸附过程可用准二级速率方程较好地描述。     

CTAB改性膨润土制备及其对海洋溢油的吸附

利用室内吸附实验,以钙基膨润土和改性后的CTAB-膨润土为研究对象,研究了改性前后的膨润土在海洋环境条件下对石油的吸附性能。结果表明,CTAB已经成功地插层到钙基膨润土层间,使其表面形貌更加蓬松,层间距增大为2.04 nm,改性后膨润土由亲水性变为疏水性。改性前后的膨润土对海洋溢油的吸附率均随着膨润土浓度的增加及粒径的减小而增加,改性后膨润土的吸油率比改性前提高了13.1%,最高达到59.5%。临界颗粒物浓度为1 000 mg·L~(-1),最佳颗粒物粒径范围为100μm。CTAB-膨润土对委内瑞拉原油的吸附过程较好地符合准二级动力学模型和Freundlich吸附等温线模型,吸附的最佳时间为240 min,最佳温度为30℃,饱和吸附量约为526 mg·g~(-1)。改性前后的膨润土在海洋环境条件下对石油的吸附性能有明显变化,CTAB-膨润土对海洋溢油的吸附优势较为显著。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.