回转窑热解处理废锌锰电池试验研究

利用回转窑装置热解处理废锌锰电池,考察了热解温度、热解时间和载气流速对热解脱汞效果的影响,研究了汞被吸收的规律、尾气的成分以及废锌锰电池的物质形态变化.研究结果表明:在热解温度为690 ℃,热解时间为100min,载气流速为0.06 m3/h的条件下脱汞效果最好.热解时间对脱汞效果影响最大,热解温度次之,载气流速的影响很小.吸收液能完全吸收通过吸收瓶的尾气中含有的汞,其中95%以上的汞以单质形式存在.热解残渣中晶态物质多,金属元素呈低价态.     

灰色预测模型及分布活化能模型在废电路板热解中的应用

分别在管式炉反应器和热天平上对废电路板的热解行为进行实验研究。在管式炉反应器上考察了在同一升温速率（20 K/min）下不同热解终温 (400、500、600、700和800℃) 对废电路板热解产物产率的影响。在相关实验数据的基础上尝试用灰色理论及方法建立基于热解终温的废电路板热解灰色产率预测模型GM(1,1)，预测结果与实验数据对比表明，该预测模型精度较高，能够较好地对不同热解终温下废电路板热解产物产率进行预测。此外，在热天平上获得的不同升温速率（10、15和20 K/min）下的热失重曲线表明，废电路板的失重速率峰随升温速率的提高逐渐向高温侧移动。采用分布活化能模型对废电路板热失重曲线进行动力学分析，获得废电路板热解活化能的变化曲线。计算结果表明，废电路板热解过程中活化能并不是单一数值，而是随失重率变化的一个函数。所得废电路板热解活化能值在140～250 kJ/mol范围内变化，当失重率在10%～60%之间，活化能值总体呈缓慢上升的趋势，但当失重率＞60%时，活化能值由155.4 kJ/mol迅速增加到244.4 kJ/mol。     

有机固体废弃物热解生产脱水内醚糖的研究

以有机固体废弃物 (废棉絮、废纸 )为原料 ,在管式炉热解反应器热解生产脱水内醚糖。研究了热解温度对热解产物相态分布的影响。同时 ,利用HPLC对脱水内醚糖的产量进行了测定。HPLC分析结果表明 :热解液水相中主要化学物质是乙酸 ,而非水相中主要化学物质是脱水内醚糖     

同步辐射光谱技术在有机固废污染控制与资源化研究中的应用

有机固废中碳、磷、硫及重金属等元素赋存形态是决定其环境行为、反应活性及资源化再利用的关键因素.同步辐射光谱技术可以在分子水平、微纳米尺度原位表征有机固废中碳、磷、硫、重金属等元素赋存形态、结合位点、微观结构,为深入阐明有机固废环境行为、反应机制提供直接的证据.概述了X射线吸收光谱、微束X射线荧光光谱等同步辐射光谱技术在有机固废污染控制与资源化研究的中应用进展,并对同步辐射光谱技术在该领域应用前景和发展趋势进行了展望,以期为有机固废资源化再利用及其污染控制等研究提供参考.     

有机固体废弃物热解生产脱水内醚糖的研究

以有机固体废弃物(废棉絮、废纸)为原料，在管式炉热解反应器热解生产脱水内醚糖。研究了热解温度对热解产物相态分布的影响。同时，利用HPLC对脱水内醚糖的产量进行了测定。HPLC分析结果表明：热解液水相中主要化学物质是乙酸，而非水相中主要化学物质是脱水内醚糖。     

医药类废盐渣的燃烧/热解特性及动力学研究

分析了维生素B6医药类废盐渣成分,采用热重(TG)/差示扫描量热(DSC)对比了废盐渣的燃烧和热解特性,并通过Coats-Redfern积分法确定了不同升温速率下废盐渣的燃烧及热解动力学参数。结果表明:该类废盐渣主要含有氯盐及磷酸盐类物质。燃烧反应比热解反应对废盐渣的热处理效果更好。升温速率对废盐渣燃烧及热解反应的反应温度、活化能和指前因子均具有不同影响。废盐渣的热解过程可用两个一级反应来描述,燃烧过程可用两个一级反应和1个二级反应来描述。     

废聚氨酯的热解及产物分析

利用热重分析仪和管式炉对废聚氨酯进行热解实验,研究了废聚氨酯的热解特性及热解产物.结果表明,废聚氨酯热解有3个失重阶段,热失重主要发生在200～440℃,600℃热失重趋于稳定.红外光谱图分析发现,热解过程中有大量CO和CO2产生.气质联用检测结果分析显示,热解产物复杂,液体产物中检出苯胺、p-苯胺、苯甲腈等多种芳香类化合物,气体产物以低碳的烷烃和烯烃为主,还检测出有机氯化合物,这是废聚氨酯中氟利昂类发泡剂所致.     

食用菌废菌棒热解的产物分布与机理解析

我国食用菌废菌棒产生量大,利用率低,对环境污染严重,需要妥善处理。为制备高品质能源,在500～800℃温度范围内快速热解废菌棒,分析产物特征,解析热解机理。热解温度从500℃上升到800℃时,废菌棒的热解气质量分数从18.44%上升到50.45%,焦油的质量分数从49.06%下降到23.72%,生物炭的质量分数维持在30%左右,废菌棒的质量减量化率超过2/3;同时,热解气中H_2、CO、CH_4含量均有上升,CO_2含量下降;焦油组分向更稳定的苯系物转变;生物炭炭化效果增强。研究结果表明,700℃为最佳热解温度,经过120 s即可反应完全。高温可以破坏羟基的结构,使其发生脱氢反应,碳氢键较早断裂,伯碳和仲碳大量裂解并迁移至焦油和热解气中,羰基在高温下迅速断链。     

废印制线路板真空热解渣分选与组成分析的研究

在自行设计制备的真空热解炉中进行了废印制线路板的热解实验，得到固体、液体和气体产物。着重研究了热解固体渣中金属铜和非金属玻璃纤维的物理分选、热解固体渣分析及有氧煅烧对玻璃纤维纯度的影响。结果表明，物理分选效率很高，金属铜的回收率和纯度接近100%；热解固体渣含30.35%的铜、56.21%的玻璃纤维和13.45%的炭黑；有氧煅烧去除炭黑可得到高纯度的玻璃纤维。     

润滑油废白土的热解处理

以润滑油废白土为原料,利用电热解法,研究了热解终温、加热速率和CaO添加量对热解产物的影响。实验结果表明:热解终温对热解产物的影响最为显著。随着热解终温的升高,不凝气产量和产油率均迅速增加。当热解终温达到600℃时,其增加的速率逐渐缓慢增大。当控制热解终温为800℃、加热速率为16℃/min、CaO添加量为0.5%时,富氢气体产量为189.2 L/kg,气体中主要成分为H2和CH4,其含量分别为27.97%和41.64%;热解残渣含油率和重金属溶出物均低于标准规定值,热解油产率为10.98%,回收率为38.94%,其主要成分为汽油、柴油和重油3部分组成,分别含19.13%、31.35%和49.52%。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.