水环境中腐殖酸与镉离子结合作用的影响因素

通过测定不同化学条件下腐殖酸与镉离子作用后的游离态镉离子浓度及其结合率，研究各因素对腐殖酸与镉离子作用的影响。研究结果表明，pH值、离子强度、投加镉离子总浓度、腐殖酸浓度和反应温度均影响腐殖酸与镉离子的结合。pH值在4.5~6.5范围内，随pH值升高，腐殖酸与Cd²⁺的结合率增大，游离态Cd²⁺浓度减少。溶液的离子强度增大对结合反应有抑制作用。投加Cd²⁺总浓度的增大会导致结合态Cd²⁺浓度和游离态Cd²⁺浓度逐渐增加，而其结合率逐渐减小。腐殖酸浓度逐渐增大，使Cd²⁺和腐殖酸的结合率逐渐增大。在20℃~50℃范围内时，随反应温度升高，游离态Cd²⁺浓度逐渐减小，其结合率逐渐增加。     

不同来源溶解态腐殖酸与Cu2+作用的荧光特性

利用三维荧光等高线图以及其所确定的荧光峰荧光强度随溶液化学条件的变化，研究不同来源溶解态腐殖酸与Cu²⁺作用的荧光特性。研究结果表明：溶解态天然腐殖酸中主要存在二类发射荧光的有机物官能团能与Cu²⁺发生络合作用。位于激发波长和发射波长分别为271～281 nm和335～351 nm的荧光峰1所代表的有机物官能团是与Cu²⁺发生络合配位的主要点位；pH值为4～6时，其络合受pH值影响较显著；而受溶液离子强度影响较小。位于激发波长和发射波长分别为223～246 nm和335～371 nm的荧光峰2所代表的有机物官能团与Cu²⁺的络合作用受溶液pH值影响较小，受溶液离子强度影响较显著。溶解态商品腐殖酸荧光峰1′所代表的有机物官能团与Cu²⁺的络合作用荧光特性，与天然腐殖酸荧光峰1所代表的有机物官能团和Cu²⁺络合作用荧光特性相似，在pH值为3～7时，其络合受pH值影响较显著。     

木粉/壳聚糖接枝丙烯酸-丙烯酰胺吸附树脂对二元重金属离子溶液中Pb2+的吸附

采用自制木粉/壳聚糖接枝丙烯酸-丙烯酰胺吸附树脂R1、R2、R3对二元金属离子Cu2 +/pb2和Zn2+/pb2+溶液中的吸附性能进行了较系统考察.pb2+离子溶液中存在竞争离子Cu2+、Zn2+时,随竞争离子浓度增加,3种吸附树脂R1、R2、R3对pb2+的吸附量明显下降,而竞争离子吸附量显著增加.二元溶液中各金属离子浓度相同时,3种树脂对竞争离子Cu2+、Zn2+的吸附量大于对pb2+的吸附量;各溶液中分别加入NaCl及NaNO3、尿素后,对pb2+离子的吸附量下降迅速.随吸附树脂用量增加,竞争离子Cu2+、Zn2+的吸附量逐渐减小,pb2+的吸附量在吸附树脂用量0.10 g/L(Zn2 +/pb2+溶液)或0.15 g/L(Cu2+/pb2+溶液)时出现最大值.溶液pH值对树脂吸附性能有显著影响.3.0＜pH＜5.O时,3种树脂对竞争离子和pb2+的吸附量快速增大;5＜ pH ＜9时,树脂对竞争离子和pb2+的吸附量基本不变;9＜pH＜ll时,树脂对pb2+的吸附量减小,而对竞争离子的吸附量或增大或减小.     

溶液环境对纳米Fe_2O_3/水界面NOM吸附过程中疏水效应的影响

以腐殖酸和纳米Fe2O3为对象,着重研究了腐殖酸分子在纳米Fe2O3表面的吸附过程中的疏水效应,借助红外光谱和热重等分析方法研究了腐殖酸吸附前后的疏水性随溶液环境变化的规律。结果表明,当离子强度为0、0.005、0.01和0.05 mol/kg,pH从7变到12时,纳米Fe2O3吸附溶解性腐殖酸分子后形成的复合体的热失重量随着pH的升高先减小后增大。当pH从7升高到10时,亲水性降低,疏水性增强;当pH从10升高到12时,亲水性增强,疏水性降低。当离子强度为0.001 mol/kg,pH从7变到12时,复合体的热失重量随着pH的升高而减小,亲水性降低,疏水性增强。当pH为定值,离子强度变化时,纳米Fe2O3吸附溶解性腐殖酸分子后形成的复合体的热失重量随着离子强度的增加不断变化,曲线呈现出波动趋势,亲、疏水性在交替变化。红外光谱分析结果说明,对纳米Fe2O3吸附溶解性腐殖酸分子后形成的复合体的亲疏水性起主要影响的官能团可能是亲水性的羟基—OH、羰基CO和疏水性的CH2烷烃。     

溶液环境对纳米Fe2O3/水界面NOM吸附过程中疏水效应的影响

以腐殖酸和纳米Fe2O3为对象,着重研究了腐殖酸分子在纳米Fe2O3表面的吸附过程中的疏水效应,借助红外光谱和热重等分析方法研究了腐殖酸吸附前后的疏水性随溶液环境变化的规律。结果表明,当离子强度为0、0.005、0.01和0.05 mol/kg,pH从7变到12时,纳米Fe2O3吸附溶解性腐殖酸分子后形成的复合体的热失重量随着pH的升高先减小后增大。当pH从7升高到10时,亲水性降低,疏水性增强;当pH从10升高到12时,亲水性增强,疏水性降低。当离子强度为0.001 mol/kg,pH从7变到12时,复合体的热失重量随着pH的升高而减小,亲水性降低,疏水性增强。当pH为定值,离子强度变化时,纳米Fe2O3吸附溶解性腐殖酸分子后形成的复合体的热失重量随着离子强度的增加不断变化,曲线呈现出波动趋势,亲、疏水性在交替变化。红外光谱分析结果说明,对纳米Fe2O3吸附溶解性腐殖酸分子后形成的复合体的亲疏水性起主要影响的官能团可能是亲水性的羟基—OH、羰基CO和疏水性的CH2烷烃。     

水环境中腐殖酸的荷电特性与聚集特性

通过腐殖酸的Zeta电位和粒径的变化规律研究,探讨化学条件对腐殖酸的荷电状态和聚集状态的影响。结果表明,腐殖酸具有自我凝聚的特性;在pH较低和溶液离子强度较高时,腐殖酸胶粒的Zeta电位绝对值减小而聚合度增大,从而使腐殖酸胶粒聚集而凝聚;随腐殖酸浓度增大,腐殖酸胶粒的Zeta电位绝对值增大,腐殖酸胶粒的缩聚程度降低而使粒径减小。     

聚丙烯酸水凝胶对氯化-1-丁基-3-甲基咪唑离子液体的吸附热力学和动力学研究

通过水溶液聚合法制备了聚丙烯酸水凝胶（polyacrylic acid,PAA）,研究了溶液酸碱度和温度对聚丙烯酸水凝胶吸附氯化1-丁基3-甲基咪唑离子液体的影响。结果表明,水凝胶对氯化1-丁基3-甲基咪唑离子液体的吸附量随溶液pH值增大而逐渐增大,pH=2～4时增幅明显,而pH大于4时变化趋于缓慢;随温度的升高而逐渐降低。该等温吸附行为基本符合Langmuir吸附等温式,由二级吸附动力学模型获得的吸附过程活化能（Ea=52.470 kJ/mol）可以看出,PAA对氯化1-丁基3-甲基咪唑的吸附属于化学吸附范畴。     

响应面法在超滤过程分析和评价中的应用

以天然水体中普遍存在的天然有机物腐殖酸(humic acid,HA)为模型污染物,采用PVC合金中空纤维超滤膜去除水中腐殖酸。以腐殖酸去除率和水透过系数作为评价指标,采用响应面法对超滤过程中溶液pH、溶液离子浓度和初始膜通量进行三因素五水平中心组合设计实验,并采用二次回归方程拟合影响因素与响应值之间的函数关系,建立回归方程。结果表明,在腐殖酸的超滤过程中,溶液pH值、溶液离子浓度、初始膜通量对腐殖酸去除率的影响显著性大小为:溶液pH值溶液离子浓度初始膜通量,对水透过系数影响显著性大小为:溶液p H值=初始膜通量溶液离子浓度。腐殖酸去除率和水透过系数方程的调整决定系数Adj.R2分别为为77.10%和88.12%,显著性水平分别为0.001504和0.0001,达到极显著水平,说明方程拟合良好,可用于超滤过程中腐殖酸去除率和水透过系数的分析和评价。     

镍网负载纳米TiO_2光催化反应器对酸性品红脱色效果实验研究

采用负载纳米TiO2的三维镍网装配了光催化反应器,就其对酸性品红溶液进行脱色效果进行了实验研究。考察了反应器的3种装配条件、品红初始浓度、pH值、H2O2投加量、紫外光剂量等因素对酸性品红脱色效果的影响。结果表明:UV灯+镍网+TiO2模式组合的反应器脱色效果最好;在相同的处理时间内酸性品红溶液的脱色率随起始浓度的增大而减小;将酸性品红溶液pH值调至5时脱色效果最明显,70 min的脱色率可高达94.8%。脱色效果还可以通过溶液中添加H2O2和控制紫外线剂量来调节。当溶液中H2O2投加量为0.5 g/L时,处理70 min后的脱色率可高达98.3%;到达反应界面紫外光剂量越多则能够获得越高的酸性品红脱色率。     

交联腐殖酸CHA对水体中铅的吸附性能

通过环氧氯丙烷交联及多胺改性的方法,制备得到新型交联腐殖酸CHA。利用FTIR对其结构进行了表征,并重点考察了吸附温度等不同因素对CHA吸附水体中铅离子性能的影响。结果表明,交联腐殖酸CHA对水体中铅离子具有优异的吸附性能,平衡吸附容量可达到219.3 mg/g,远高于常规高温焙烧方法制得腐殖酸的吸附性能。CHA的吸附性能随反应温度、溶液pH的升高而增大,其吸附过程符合Langmuir吸附方程。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.