脱木素工艺处理造纸废水的实践与机理

脱木素工艺为中小制浆企业的黑液治理提供了新的方法。系统中酸化纤维污泥减小碱木素胶粒间的斥力 ,吸附废水中已析出的木质素和细小纤维 ;酸破坏了系统中胶体的水化膜 ,增大了胶体的粒径 ;混凝剂中和胶体表面电荷 ,增加颗粒间的接触机会 ,同时发挥了絮凝沉降的作用。该工艺与传统工艺相比 ,减少了酸及混凝剂的用量 ,木素沉降速度快。当试验废水pH =5、绝干纤维污泥与进水CODCr质量之比为 1.1、硫酸铝投加量为 160mg/L时 ,CODCr去除率高于 63 %。     

碱回收工艺废渣——白泥综合治理

碱回收工艺是造纸行业综合治理造纸黑液的一种行之有效的办法。用一吨石灰就能从造纸黑液中回收一吨烧碱,经济效益十分显著。但随之而带来的问题是每回收一吨造纸黑液约要产生一吨白泥废渣。白泥呈灰白色浆状,pH 值11～14,主要化学成份见表1,其中碳酸钙约占95%。     

脱木素工艺处理造纸废水的实践与机理

脱木素工艺为中小制浆企业的黑液治理提供了新的方法。系统中酸化纤维污泥减小碱木素胶粒间的斥力，吸附废水中已析出的木质素和细小纤维；酸破坏了系统中胶体的水化膜，增大了胶体的粒径；混凝剂中和胶体表面电荷，增加颗粒间的接触机会，同时发挥了絮凝沉降的作用。该工艺与传统工艺相比，减少了酸及混凝剂的用量。木素沉降速度快。当试验废水pH=5，绝干纤维污泥与进水CODCr质量之比为1.1，硫酸铝投加量为160mg/L时，CODCr去除率高于63%。     

碱法造纸-黑液-氧化铝联产的工业共生模式研究

应用生态工业和系统工程原理,以碱法麦草化学制浆造纸黑液为研究对象,对其资源化过程开展研究.在归纳造纸黑液资源化多产品工业共生方案基础上,通过物质流、能量流定量分析,通过环境、经济、技术和市场诸因素的综合评价,提出了碱法造纸-黑液-氧化铝联产的工业共生模式.该工业共生模式不仅消除了传统造纸黑液的处理方法对环境的污染,而且将造纸黑液变废为宝,由污染源直接变成生产原料加以利用,为造纸黑液资源化提供了一种可以借鉴的发展模式.     

改善环保疏浚底泥脱水干化效能的实验研究

采用以硫酸亚铁(FeSO4)为主要成分的复合脱水剂作为疏浚泥浆脱水剂(以下简称脱水剂),黄沙、炉渣、煤灰、石灰和粉煤灰分别作为疏浚底泥干化改良剂进行实验研究。结果表明,在脱水剂投加量为100 mg/L条件下,可以提高沉淀效率约20%;在投加脱水剂及5%石灰、粉煤灰、炉渣改良剂的条件下,底泥比阻值下降50%～70%;初期渗水速率提高6%～68%;与原泥相比,以黄沙、炉渣、煤灰为改良剂的底泥,经过4个月干化期后,承载力提高了30%～150%。本研究为疏浚底泥快速脱水干化提供了一种可行的技术途径。     

麻料浆黑液和稻草浆黑液综合利用新路子

传统的碱回收工艺只适用于木浆和麦草浆,而对稻草浆黑液和麻料浆黑液不能适用.浙江省稻草和麻皮资源丰富,很多纸厂都用作原料,急需解决黑液处理问题.浙江民丰造纸厂和轻工业部造纸研究所对此进行了研究,已取得初步成果并于九月下旬通过鉴定.该方法利用麻料黑液作为稻草浆蒸煮液,同时将稻草浆黑液经过     

碳源强化下的硫自养/异养反硝化协同作用

为强化硫自养反硝化过程,通过向连续稳定运行的硫自养反硝化反应器内投加少量碳源以进行强化,乙酸钠投加量分别为5.99、11.98、23.96 mg·L~(-1)。分析投加前后反应器内硝氮、COD、硫酸根和耗碱量的变化;研究了碳源强化下硫自养反硝化运行效能及反应机理。结果表明,投加少量碳源可增强自养反硝化过程硝氮的去除效果;在3种碳源投加量条件下,COD的利用率均大于85%,但硫酸盐生成量并未减少;在5.99 mg·L~(-1)碳源投加量下,系统实际耗碱量大于以硫酸根和COD计的理论耗碱量,而在11.98 mg·L~(-1)和23.96 mg·L~(-1)投加量下,实际耗碱量均介于2种理论值之间。在投加少量碳源后,自养反硝化脱氮效果明显提高,异养反硝化趋势随着碳源投加量的增加而增加。     

造纸废水生化降解工艺的应用与探讨

结合工程实例 ,讨论了生化法对麦草碱法造浆黑液及造纸综合废水处理的可行性。探讨结果表明 ,只要控制适当的理化条件、驯化优势菌种 ,微生物方法对造纸综合废水及黑液CODCr的降解具有显著的作用 ,做到达标排放是完全可能的。     

热碱预处理对高含固剩余污泥厌氧消化的影响及其动力学研究

以高含固剩余污泥为研究对象,考察不同碱投加量下热碱联合预处理对剩余污泥溶胞效果和厌氧消化性能的影响,并运用3种动力学模型对剩余污泥生物化学产甲烷潜力过程进行模拟。结果表明,热碱联合预处理有助于促进剩余污泥的溶胞效果,并且随着碱投加量的增加,溶胞效果不断增强,当碱投加量为80mg/g(单位质量SS的NaOH投加量计)时,COD、氮、磷的溶出量均达到最大值,分别为58 622.2、1 792.8、790.3mg/L,溶出率分别为54.9%、45.7%、37.6%。热碱联合预处理可有效改善剩余污泥厌氧消化性能,但碱投加量过大时对可能对产甲烷过程带来抑制作用,碱投加量为60mg/g时剩余污泥厌氧消化的累积产甲烷量最大,为158.9mL/g,较不进行热碱联合预处理的空白组(106.5mL/g)高49.2%。3种动力学模型中,锥体模型对厌氧消化产甲烷过程的拟合效果最好,不同处理条件下模型拟合相关系数R~2均在0.990以上,该模型可准确预测最终的累积产甲烷量,预测误差均在2%以下。     

乙醛生产废水碱解脱毒预处理

对乙醛生产废水进行碱解预处理,研究碱投加量、反应温度、反应时间对脱毒效果的影响。结果表明,乙醛生产废水经碱解预处理后,废水中有毒物质降解明显,且厌氧生物毒性和好氧活性污泥毒性显著下降。碱投加量、反应温度和反应时间是影响乙醛生产废水碱解预处理效果的重要因素,在反应时间为0.5 h,碱投加量为1.2 g/L,反应温度为30℃,好氧活性污泥毒性即可有大幅下降;产甲烷抑制率在反应时间为3 h以上,反应温度为60℃、碱投加量为2 g/L以上,有大幅下降。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.