分光光度法测定室内空气中甲醛的方法研究

针对室内空气中甲醛的特点,在环境空气甲醛的测定方法—乙酰丙酮分光光度法(GB/T15516-95)的基础上,进一步优化了该方法的采样时间、采样流量、样品收集器等,使优化后的测定方法更加适应室内空气监测需要的准确性、简便性、快速性的特点。     

Measurement of styrene-7,8-oxide and other oxidation products of styrene in air

Styrene-7,8-oxide (SO) is generated at low concentrations from the oxidation of styrene during the processing of reinforced plastics. Since exposure to SO has important health implications, we developed air sampling and analytical methods to measure low levels of airborne SO in the presence of styrene and its other oxidation products, namely phenylacetaldehyde (PAA) and acetophenone (AP). Both active and passive air monitors were used. The active sampling method, which employed adsorption on Tenax, was suitable for measuring SO, PAA and AP but had limited capacity for styrene due to breakthrough. The passive monitor employed a carbon adsorbent and was suitable for measurement of styrene and SO but not PAA and AP due to poor recovery. After sampling, the analytes were extracted from the adsorbents with ethyl acetate and measured by gas chromatography with flame ionization detection or mass spectrometry. By maintaining the injection port at 70 degrees C, the thermal rearrangement of SO to PAA was minimized. Recovery of styrene and SO from the passive monitor depended upon loading and was corrected by linearization of the Freundlich isotherm. The limits of detection for SO, PAA, and AP were 0.2 ppb using the active monitor, and for SO was 1 ppb using the passive monitor. The sampling precision for SO (RSD from personal measurements) was 5.0% for the passive monitor and was 13.4% for the active monitor over a range of exposures from 5-150 ppb. The corresponding precision for styrene was 5.3% for the passive monitor for levels ranging from 1.2 to 104 ppm. Measurements of 235 personal exposures with the active monitor in 12 facilities manufacturing fiberglass-reinforced plastics (FRP) showed that levels of AP and PAA were below 7.8 ppb and 5 ppb, respectively. In contrast, SO averaged 30.4 ppb (SE=2.4) in these FRP facilities, ranging from below 0.2 ppb to 190 ppb. The active monitor was also used to detect airborne SO at levels of approximately equals 1 ppb in one facility manufacturing styrene butadiene rubber, suggesting that SO is generally present during the polymerization of styrene. Personal passive monitoring in the 12 FRP facilities (n = 657) revealed mean concentrations of styrene ranging between 1.8 and 55.4 ppm, and for SO between 1.7 and 62.6 ppb. The ratio of the mean styrene level to the mean SO level varied between 449:1 and 1,635:1 among the 12 FRP facilities.     

A diffusive sampling device for the determination of formaldehyde in air using N-methyl-4-hydrazino-7-nitrobenzofurazan (MNBDH) as reagent

A new method utilizing the diffusive sampling of formaldehyde in air has been developed. Formaldehyde is sampled with the use of a glass fiber filter impregnated with N-methyl-4-hydrazino-7-nitrobenzofurazan (MNBDH) and phosphoric acid. The formaldehyde hydrazone formed is desorbed from the filter with acetonitrile and determined by high-performance liquid chromatography (HPLC) with UV/visible detection at 474 nm. The sampling rate was determined to be 24.7 mL min-1 with a relative standard deviation of 7% for 48 experiments. The measured sampling rates were not dependent on the formaldehyde concentration (0.1-1.0 mg m-3), sampling time (15-482 min) or relative humidity (20-85%). The detection limit was 70 micrograms m-3 for a 15 min sampling period and 2 micrograms m-3 for an 8 h sampling period.     

Determination of the dialdehyde glyoxal in workroom air-development of personal sampling methodology

The dialdehyde glyoxal (ethanedial) is an increasingly used industrial chemical with potential occupational health risks. This study describes the development of a personal sampling methodology for the determination of glyoxal in workroom air. Among the compounds evaluated as derivatizing agents; N-methyl-4-hydrazino-7-nitrobenzofurazan (MNBDH), 1,2-phenylenediamine (OPDA), 1-dimethylaminonaphthalene-5-sulfonylhydrazine (dansylhydrazine, DNSH) and 2,4-dinitrophenylhydrazine (DNPH), DNPH was the only reagent that was suitable. Several different samplers were evaluated for sampling efficiency of glyoxal in workroom air using DNPH as derivatizing agent; in-house DNPH coated silica particles packed in two different types of glass tubes, impingers containing acidified DNPH solution, filter cassettes containing glass fibre filters coated with DNPH, a commercially available solid phase cartridge sampler originally developed for formaldehyde sampling (Waters Sep-Pak DNPH-silica cartridge), and the commercially available SKC UMEx 100 passive sampler originally developed for formaldehyde sampling. Aldehyde atmospheres for sampler evaluation were generated with an in-house made vapour atmosphere generator coupled to a sampling unit, with the possibility of parallel sampling. The resulting glyoxal-DNPH derivative was determined using both LC-UV and LC-APCI-MS with negative ionization. By far, the highest recovery of glyoxal was obtained employing one of the in-house DNPH coated silica samplers (93%, RSD = 3.6%, n = 12).     

Colorimetric determination of formaldehyde in air using a hanging drop of chromotropic acid

A simple and sensitive method to determine parts per billion (ppb) of atmospheric formaldehyde in situ, using chromotropic acid, is described. A colorimetric sensor, coupled to a droplet of 15.5 microL chromotropic acid, was constructed and used to sample and quantify formaldehyde. The sensor was set up with two optical fibers, a light emitting diode (LED) and two photodiodes. The reference and transmitted light were measured by a photodetection arrangement that converts the signals into units of absorbance. Air was sampled around the chromotropic acid droplet. A purple product was formed and measured after the sampling terminated (typically 7 min). The response is proportional to the sampling period, analyte concentration and sample flow rate. The detection limit is approximately 2 ppb and can be improved by using longer sampling times and/or a sampling flow rate higher than that used in this work, 200 mL min-1. The present technique affords a simple, inexpensive near real-time measurement with very little reagent consumption. The method is selective and highly sensitive. This sensor could be used either for outdoor or indoor atmospheres.     

The influence of water vapour on the determination of glutaraldehyde vapour concentrations using an electrochemical fuel cell sensor

The effects of relative humidity (40-90% RH) and varying glutaraldehyde vapour concentrations (< 0.1 ppm) on the response of an electrochemical fuel cell sensor have been investigated over time (0-400 s). These studies have identified changes in the response of the fuel cell with time after sampling. In particular, it has been found that the maximum cell output for water vapour occurs ca. 10 s after sampling whilst the response to glutaraldehyde occurs much later (> 100 s). For mixtures containing different ratios of water and glutaraldehyde vapours, the time taken to reach maximum fuel cell response varies between 10 and 100 s, depending on the ratio of the two vapours. For instance, glutaraldehyde vapour containing higher % RH has been found to result in shorter times to reach maximum fuel cell response. A comparison was made between measuring glutaraldehyde vapour concentrations in the presence of water vapour at the maximum fuel cell response and also at a fixed interval (240 s) after sampling. Such a comparison resulted in a reduction in the standard error from 36% to 5% for a glutaraldehyde vapour sample (0.023 ppm) measured at different values of relative humidity (40 to 80%). Examination of the effect of the sample volume (30-60 ml) on the response of the fuel cell shows, as expected, an approximate doubling of the fuel cell response. Optimisation of the fuel cell measurement parameters to measure a 60 ml sample leads to a lowering of the limit of detection from 0.083 ppm (for data taken at the maximum cell response) to 0.017 ppm for data measured 240 s after sampling. In the light of recent reductions in the legal limits for exposure to glutaraldehyde, this has important implications for the measurement of glutaraldehyde vapour in the workplace.     

Development of active and diffusive sampling methods for determination of 3-methoxybutyl acetate in workplace air

Monitoring of the workplace concentration of 3-methoxybutyl acetate (MBA), which is used in printer's ink and thinner for screen-printing and as an organic solvent to dissolve various resins, is important for health reasons. An active and a diffusive sampling method, using a gas chromatograph equipped with a flame ionization detector, were developed for the determination of MBA in workplace air. For the active sampling method using an activated charcoal tube, the overall desorption efficiency was 101%, the overall recovery was 104%, and the recovery after 8 days of storage in a refrigerator was more than 90%. For the diffusive sampling method using the 3M 3500 organic vapor monitor, the MBA sampling rate was 19.89 cm(3) min(-1). The linear range was from 0.01 to 96.00 microg ml(-1), with a correlation coefficient of 0.999, and the detection limits of the active and diffusive samplers were 0.04 and 0.07 microg sample(-1), respectively. The geometric mean of stationary sampling and personal sampling in a screen-printing factory were 12.61 and 16.52 ppm, respectively, indicating that both methods can be used to measure MBA in workplace air.     

Assessment of indoor airborne contamination in a wastewater treatment plant

The main objective of this work was to quantify and characterize the major indoor air contaminants present in different stages of a municipal WWTP, including microorganisms (bacteria and fungi), carbon dioxide, carbon monoxide, hydrogen sulfide ammonia, formaldehyde, and volatile organic compounds (VOCs). In general, the total bacteria concentration was found to vary from 60 to >52,560 colony-forming units (CFU)/m³, and the total fungi concentration ranged from 369 to 14,068 CFU/m³. Generally, Gram-positive bacteria were observed in higher number than Gram-negative bacteria. CO₂ concentration ranged from 251 to 9,710 ppm, and CO concentration was either not detected or presented a level of 1 ppm. H₂S concentration ranged from 0.1 to 6.0 ppm. NH₃ concentration was <2 ppm in most samples. Formaldehyde was <0.01 ppm at all sampling sites. The total VOC concentration ranged from 36 to 1,724 μg/m³. Among the VOCs, toluene presented the highest concentration. Results point to indoor/outdoor ratios higher than one. In general, the highest levels of airborne contaminants were detected at the primary treatment (SEDIPAC 3D), secondary sedimentation, and sludge dehydration. At most sampling sites, the concentrations of airborne contaminants were below the occupational exposure limits (OELs) for all the campaigns. However, a few contaminants were above OELs in some sampling sites.     

空气自动监测系统运行管理故障处理

结合宿迁市空气质量自动监测系统运行实践,解析API点式仪器SO2、NOX分析仪校标不稳、测值偏低,BAM-1020BETA射线颗粒物监测仪纸带易破,数据采集系统线路不畅、数据不完整等常见故障,提出相应的解决方法和预防对策.     

A method for measuring dermal exposure to multifunctional acrylates

UV-curable acrylates are used increasingly for coating wood surfaces in the furniture industry. One of the active components, tripropylene glycol diacrylate (TPGDA), is known to be both an allergen and irritant to the skin. Methods to measure dermal exposure to skin irritants and allergens, such as acrylates, are insufficient for exposure assessment and there is none for this compound. The aim of this investigation was to develop a skin and surface sampling method, based on tape stripping, and a gas chromatographic method for quantitative analysis for assessing occupational skin exposure to multifunctional acrylates. Twelve adhesives were tested for their efficiency to remove TPGDA and UV-coating from a glass surface, the skin of guinea pigs and human volunteers employing the tape-stripping method in order to find the best performing tape. Variables that affect removal efficiency such as the applied dose and its retention time on the skin, tape adhesion time on the skin, and the number of strippings required to detect the contaminant from the skin were studied. Fixomull tape performed the best during sampling and analysis and had the most consistent removal efficiencies for the studied substances. The average removal efficiency with a single stripping at the 2 microliters TPGDA exposed skin sites was 85% (RSD = 14.1), and for UV-resin exposed sites 63% (RSD = 20.2). The results indicated that this method can be used for measuring dermal exposure to multifunctional acrylates efficiently, accurately, and economically. This method provides a sensitive and powerful tool for the assessment of dermal exposure to multifunctional acrylates both from the skin and from other contaminated surfaces in occupational field settings.     

Compact semi-automatic incident sampler for personal monitoring of volatile organic compounds in occupational air

Suddenly occurring and time limited chemical exposures caused by unintended incidents might pose a threat to many workers at various work sites. Monitoring of exposure during such occasional incidents is challenging. In this study a compact, low-weight and personal semi-automatic pumped unit for sampling of organic vapor phase compounds from occupational air during sporadic and suddenly occurring incidents has been developed, providing simple activation by the worker potentially subjected to the sudden occurring exposures when a trained occupational hygienist is not available. The sampler encompasses a tube (glass or stainless steel) containing an adsorbent material in combination with a small membrane pump, where the adsorbent is capped at both ends by gas tight solenoid valves. The sampler is operated by a conventional 9 V battery which tolerates long storage time (at least one year), and is activated by pulling a pin followed by automatic operation and subsequent closing of valves, prior to shipping to a laboratory. The adjustable sampling air flow rate and the sampling time are pre-programmed with a standard setting of 200 mL min(-1) and 30 min, respectively. The average airflow in the time interval 25-30 min compared to average airflow in the interval 2-7 min was 92-95% (n = 6), while the flow rate between-assay precisions (RSD) for six different samplers on three days each were in the range 0.5-3.7%. Incident sampler recoveries of VOCs from a generated VOC atmosphere relative to a validated standard method were between 95 and 102% (+/-4-5%). The valves that seal the sampler adsorbent during storage have been shown to prevent an external VOC atmosphere (500 mg m(-3)) to enter the adsorbent tube, in addition to that the sampler adsorbent is storable for at least one month due to absence of ingress of contaminants from internal parts. The sampler was also suitable for trapping of semi-volatile organophosphates.     

二氧化硫甲醛吸收液动态稳定性的实验研究

通过对测定大气中二氧化硫甲醛吸收液动态稳定性的研究,探讨了稳定性对２４小时连续监测（手工采样）结果的影响及采样时间、流量和吸收液用量因素对监测结果影响的理论揭示。     

副玫瑰苯胺无汞比色法测定空气中的甲醛

在甲醛法测定空气中二氧化硫的基础上,建立了一种测定空气中甲醛的新方法。该方法所用设备和材料与甲醛法测定空气中的二氧化硫相同,不使用含汞试剂,用亚硫酸钠固定标准溶液和吸收液中的甲醛,用氢氧化钠分解羟甲磺酸释放已被固定的甲醛,以副玫瑰苯胺和亚硫酸钠为显色剂绘制标准曲线进行定量。当采集空气30L时,检出限为0.01mgm3,最低检测浓度为0.03mgm3,适用于环境空气及室内空气中甲醛的测定。     

Experimental and Numerical Analysis of CO Concentration Dispersion of Vehicular Exhaust Emissions in Isolated Environment

Numerical and experimental analyses were applied to carbon monoxide (CO) concentration dispersion to monitor air quality in an enclosed residential complex parking area in Tehran. Firstly, the parking area was preliminary assessed through verifying the characteristics of the problem including the geometry and boundary conditions. Then, proportion of vehicular exhaust emissions was estimated and eventually experimental and numerical analyses were performed. In order to perform numerical calculation, a three-dimensional model was created to numerically simulate the enclosed residential complex parking area by FLUENT software that solves flow governing equations with finite volume method. In FLUENT, species model was selected to assess the dispersion of CO in flow domain. In experimental analysis, CO concentration was measured using sampling bags with a volume of 10 l in 4 min at 6 different points. The sample air was drawn into sampling bags by electric pumps. The findings show that the maximum amount of CO concentration is above the permissible standard recommended by the World Health Organization. Pollutant accumulation was significant in confined areas. In the place where openings exist, the level of accumulation was lower than other areas. The findings obtained from numerical simulation are in complete accord with experimental results.     

The determination of carbonyl compounds in air using a robotic sampling preparation system integrated to a gas chromatograph with a nitrogen-phosphorus detector

A totally automated solid phase extraction gas chromatography procedure was developed for the sampling and analysis of carbonyl compounds in air. In this system, two PrepStation modules were used, one for the preparation and elution of 2,4-dinitrophenylhydrazine silica cartridges, and the other for air sampling. The sample collected by the sampling module was eluted to an autosampler vial in the PrepStation module and then transferred to the gas chromatograph for analysis via a robotic arm. The sampling module was modified to enable air sampling via an external pump. A typical run by this technique required 142 min, 100 min for air sampling and 42 min for the other operations, including a GC analysis time of 25 min. Recoveries of at least 85% were obtained for all compounds studied. The detection limits for formaldehyde, acetaldehyde and acetone were 2.2, 2.7 and 2.2 ppbv, respectively. All operations, including the conditioning of the cartridges, were performed without any intervention from the analyst.     

Formaldehyde determination in seawater. Preliminary application to coastal samples at Terra Nova Bay (Antarctica)

A sensitive spectrofluorimetric-FIA (flow injection analysis) method for formaldehyde (HCHO) determination was improved with the aim of analysing seawater samples.The fluorescence emission versus HCHO concentration shows a linear pattern from sub microg L(-1) to about 1000 microg L(-1). The reproducibility at 15 ppb level is about 2%. Interferences from other aldehydes were checked; only glyoxal shows a significative interference, but only when its concentration is about 6000 times higher than that of formaldehyde. Superficial (microlayer, just sub-pack or sea-ice free sea surface) and deep (along the water column, sub-pack or in sea-ice free areas) seawater samples were collected near the coast at Terra Nova Bay (Ross Sea, Antarctica) during the 1998/1999 and 2001/2002 Italian Antarctic Expedition. We report here the preliminary results of the spectrofluorimetric-FIA determination of the HCHO content. The mean seawater superficial formaldehyde concentration was 15 microg L(-1); the concentration along the water column ranged between 4.5 to over 40 microg L(-1)(20 microg L(-1) mean concentration), usually with a maximum value for the 30 m depth, corresponding to a fluorescence maximum. The sampling was repeated 7 times in the austral summer in order to evaluate seasonal changes in the formaldehyde concentration/seawater depth profiles. The results show changes in the formaldehyde concentration at different depths.     

固定源硫酸雾国内外采样方法优劣分析

固定污染源硫酸雾的国标采样方法为滤筒法，但对其采样效率研究较少。在调研国内外标准方法及相关文献的基础上，通过大量实样测定，对国标采样法进行改进：在内装滤筒的烟尘采样管后串联一个冲击式吸收瓶，此改进方法弥补了国标漏测气态硫酸雾的缺陷，采样效率达到99％以上，国标法仅为改进法的47％～68％。将国标改进法与USEPA采样法进行比对，结果表明，由于中国环境本底颗粒物浓度较高，硫酸雾易吸附于颗粒物上，致使USEPA采样效率仅为国标改进法的2?4％～12％。     

Determination of acrylic acid in air by using diffusion denuder tubes combined with HPLC technique

A procedure for the determination of atmospheric acrylic acid in air at the microgram m-3 to mg m-3 level is described. Diffusion-based sampling, designed to discriminate gaseous analytes from their particulate counterparts, has been used. Acrylic acid is collected with an efficiency of > 98% in tubular denuders coated with sodium hydroxide-barium hydroxide-hydroquinone monomethyl ether, and analyzed by high performance liquid chromatography with UV absorbance detection. The detection limit is 2.9 micrograms m-3 at a flow rate of 0.5 L min-1 and 30 min sampling time. A precision (p = 0.95, n = 10) of 7.5% of the overall procedure was achieved at the 100 micrograms m-3 level. Results of laboratory studies concerning the effect of the coating reagent and the relative humidity on the sampling efficiency as well as possible interferences, in particular by ozone, and the elimination of these interferences are discussed. This method was developed to monitor workplace atmospheres as well as ambient air in industrial environments.     

Air formaldehyde and solvent concentrations during surface coating with acid-curing lacquers and paints in the woodworking and furniture industry

An investigation of contemporary exposure to formaldehyde and organic solvents has been carried out during surface coating with acid-curing lacquers and paints in the Norwegian woodworking and furniture industry over a period of 3 years. The investigation covered 27 factories of different sizes and with different types of production, and totally 557 parallel formaldehyde and solvent samples were collected. The formaldehyde concentration (geometric mean) was 0.15 ppm (range 0.01-1.48 ppm) with about 10% of the samples exceeding the Norwegian occupational exposure limit of 0.5 ppm. The solvent concentration as additive effect (geometric mean) was 0.13 (range 0.0004-5.08) and about 5% of the samples exceeded the Norwegian occupational exposure limit. The most frequently occurring solvents from acid-curing lacquers were n-butyl acetate, ethanol, ethyl acetate and 1-butanol, which were found in 88-98% of the samples. Toluene, n-butyl acetate and 1-butanol were the only solvents with maximum concentrations exceeding their respective occupational exposure limits. Curtain painting machine operators were exposed to the highest concentrations of both formaldehyde (geometric mean 0.51 ppm, range 0.08-1.48 ppm) and organic solvents (additive effect, geometric mean 1.18, range 0.02-5.08). Other painting application work tasks such as automatic and manual spray-painting, manual painting and dip painting, showed on average considerably lower concentrations of both formaldehyde (geometric means 0.07-0.16 ppm) and organic solvents (additive effect, geometric mean 0.02-0.18). Non-painting work tasks also displayed moderate concentrations of formaldehyde (geometric means 0.11-0.17 ppm) and organic solvents (additive effect, geometric mean 0.04-0.07).     

固体进样-电热蒸发-原子吸收法测定土壤中的镉

采用固体进样原子吸收法直接测定土壤中的镉,可以避免传统酸消解预处理过程耗时长、试剂消耗大、操作步骤繁琐等缺点,提升镉的检测效率。通过优化测镉仪的仪器参数,确定了固体进样-电热蒸发-原子吸收法的优化仪器条件。采用优化条件测定了不同浓度的土壤样品,研究了该方法的检出限、正确度、精密度。研究结果表明:镉质量范围为0~200 ng时与峰面积的线性相关系数优于0.999 5,空气流下优化的灰化温度和热解温度均为800 ℃,优化的热解气体氢气流量为300 mL/min,当样品进样量为0.1 g时,检出限为0.009 mg/kg,7次连续测定相对标准偏差为1.4%~5.0%,加标回收率为96.2%~102.1%,分析时间小于4 min。该方法操作简便,用时短,无需高压气源,可以用于土壤中镉的高效检测。