Assessment of elemental concentrations in the urban air (case study: Tehran city)

Tehran is one of the megacities of the world with a population of over eight million. Its air is highly polluted mainly due to the suspended particulate matters, which encompasses a wide spectrum of chemical elements. These elements based on their type, size, and impact on the life cycle have various environmental and heath risks. In this research, the neutron activation method is used to determine the concentration levels of Al, Ba, Fe, Mg, and V in the urban air. Thus, two districts of Tehran with different characteristics are selected. District 21 includes much of the industries located in Tehran metropolitan and is considered as an industrial area. In contrast, district 22 lacks any significant industrial activity. It is a newly established and expanding district adjacent to district 21 with a great deal of constructional activities. For the measurement of the suspended particulate matters in the air, the various sections of the aforesaid districts with industrial, residential, heavily congested traffic, residential/commercial, residential/heavily congested traffic, and residential/industrial classifications were identified. Subsequently, 24 sampling stations were selected. The sampling of the suspended particulate matters was conducted with the aid of a high volume pump containing 125 mm cellulose filters in two different time intervals. After completion of the sampling process, the samples were prepared and sent to the research reactor of the Iran Nuclear Energy Organization for Neutron Activation. During the next steps, the radiations emitted from the samples were registered, the radiation curves were plotted, and the amounts of the trace elements were determined. As a result, the average concentration levels of Al, Ba, Fe, Mg, and V were identified to be 3.301140, 2.273658 × 10, 4.0681696 × 10^???1, 3.5525475 × 10^???1, and 3.04075 × 10^???2 μg/m³, respectively. Moreover, the emission sources of the aforesaid elements into the air were identified. The concentration levels of these elements in the industrial and heavily congested traffic sections were higher. Finally, it was concluded that the statistical analysis of these elements presents a meaningful correlation among them.     

GCMS法测定大气醛类恶臭物质的采样袋适用性研究

采用气袋采样-GCMS分析法测定大气中丙醛等5种醛类恶臭物质,对Tedler等5种不同材质采样袋进行适用性研究。结果表明,Tedler 2号采样袋对低浓度醛类回收率影响最小,低浓度醛类在其中能稳定存放12 h,在PVDFs采样袋中低浓度醛类须在6 h内测定,高浓度醛类在Tedler 2号采样袋和PVDFs采样袋中能较稳定地保存24 h,24 h内的回收率在78%以上。     

Comparison of exhaled carbon monoxide levels among commuters and roadside vendors in an urban and a suburban population in Pakistan

Carbon monoxide (CO) is one of the six criteria air pollutants related to urbanization and has a wide range of health effects. The study measured and compared the exhaled CO levels among commuters and roadside vendors in potentially heavy and low traffic volume areas of Karachi, a megacity in Pakistan. Saddar town [areas of M. A. Jinnah Road (Tibet Center, Denso Hall) and Empress Market] was selected to represent an area of high traffic volume and the suburban town of Gadap (Gadap and Gulshan-e-Maymar) was selected to represent an area of no or low traffic volume. The study compared the CO exposure of commuters and roadside vendors in high and low traffic volume in Karachi. CO exposure was measured in expired air using the breath analyzer module of Bacharach Monoxor-II, USA. A total of 326 individuals (115 commuters and 211 stationary roadside vendors) from Saddar town (n?=?193) and Gadap town (n?=?133) were selected. In addition, CO levels in ambient air in the same areas, using portable CO analyzer (Bacharach, Monoxor-II, USA), were measured. The mean ambient CO level at Saddar town was 15.6 (SE ± 2.6) ppm compared to 3.3 (SE ± 0.3) ppm at Gadap town. The mean CO level in expired air was significantly higher among nonsmokers at Saddar town (12.8 ± 0.5 ppm) compared to the nonsmokers at Gadap town (7.8 ± 0.4 ppm). The mean CO level in expired air among smokers was twice that of nonsmokers (21.6 vs. 10.6 ppm). CO in expired air was greater among high traffic volume commuters and roadside stationary population in Karachi, Pakistan. The population in Karachi is exposed to high concentration of air pollutants. These pollutants need to be characterized for health effects and interventions needs to be developed.     

Preparation and Validation of Gridded Emission Inventory of Criteria Air Pollutants and Identification of Emission Hotspots for Megacity Delhi

Delhi is one of the many megacities struggling with punishing levels of pollution from industrial, residential, and transportation sources. Over the years, pollution abatement in Delhi has become an important constituent of state policies. In the past one decade a lot of policies and regulations have been implemented which have had a noticeable effect on pollution levels. In this context, air quality models provide a powerful tool to study the impact of development plans on the expected air pollution levels and thus aid the regulating and planning authorities in decision-making process. In air quality modeling, emissions in the modeling domain at regular interval are one of the most important inputs. From the annual emission data of over a decade (1990–2000), emission inventory is prepared for the megacity Delhi. Four criteria pollutants namely, CO, SO₂, PM, and NO _x are considered and a gridded emission inventory over Delhi has been prepared taking into account land use pattern, population density, traffic density, industrial areas, etc. A top down approach is used for this purpose. Emission isopleths are drawn and annual emission patterns are discussed mainly for the years 1990, 1996 and 2000. Primary and secondary areas of emission hotspots are identified and emission variations discussed during the study period. Validation of estimated values is desired from the available data. There is a direct relationship of pollution levels and emission strength in a given area. Hence, an attempt has been made to validate the emission inventory for all criteria pollutants by analyzing emissions in various sampling zones with the ambient pollution levels. For validation purpose, the geographical region encompassing the study area (Delhi) has been divided into seven emission zones as per the air quality monitoring stations using Voronoi polygon concept. Dispersion modeling is also used for continuous elevated sources to have the contributing emissions at the ground level to facilitate validation. A good correlation between emission estimates and concentration has been found. Correlation coefficient of 0.82, 0.77, 0.58 and 0.68 for CO, SO₂, PM and NO _x respectively shows a reasonably satisfactory performance of the present estimates.     

Qualitative Detection of Volatile Organic Compounds in Outdoor and Indoor Air

The present work attempts to identify VOC's in outdoor and indoor air in Mumbai City India. Ambient air was adsorbed on especially fabricated stainless steel cartridge packed with activated coconut charcoal at uniform flow rate. Qualitative identification of VOC's was done by thermally desorbing air from the cartridges and subsequent analysis on Varian GC-MS using NIST Library. The outdoor monitoring locations include residential area, commercial area, industrial, airport, petrol pumps, traffic junctions, arterial roads, highways, slums, parking area, service garages and municipal dump sites. The indoor locations comprised of air-conditioned and non air-conditioned offices, bedrooms, shops and instrumentation laboratory. The identified VOC's include aldehydes, ketones, polynuclear aromatic hydrocarbons, aromatic acids, oxygenated hydrocarbons, amines, esters and halogenated compounds. Thirteen VOCs in outdoor air and seven in indoor air amongst those identified, figure in the list of Hazardous Air Pollutants listed in Title III of the U.S. EPA Clean Air Act Amendments of 1990.     

Assessment of indoor airborne contamination in a wastewater treatment plant

The main objective of this work was to quantify and characterize the major indoor air contaminants present in different stages of a municipal WWTP, including microorganisms (bacteria and fungi), carbon dioxide, carbon monoxide, hydrogen sulfide ammonia, formaldehyde, and volatile organic compounds (VOCs). In general, the total bacteria concentration was found to vary from 60 to >52,560 colony-forming units (CFU)/m³, and the total fungi concentration ranged from 369 to 14,068 CFU/m³. Generally, Gram-positive bacteria were observed in higher number than Gram-negative bacteria. CO₂ concentration ranged from 251 to 9,710 ppm, and CO concentration was either not detected or presented a level of 1 ppm. H₂S concentration ranged from 0.1 to 6.0 ppm. NH₃ concentration was <2 ppm in most samples. Formaldehyde was <0.01 ppm at all sampling sites. The total VOC concentration ranged from 36 to 1,724 μg/m³. Among the VOCs, toluene presented the highest concentration. Results point to indoor/outdoor ratios higher than one. In general, the highest levels of airborne contaminants were detected at the primary treatment (SEDIPAC 3D), secondary sedimentation, and sludge dehydration. At most sampling sites, the concentrations of airborne contaminants were below the occupational exposure limits (OELs) for all the campaigns. However, a few contaminants were above OELs in some sampling sites.     

Levels, sources, and health risks of carbonyls in residential indoor air in Hangzhou, China

Concentrations of formaldehyde, acetaldehyde, acetone, propionaldehyde, i-pentanal, and butyraldehyde in residential indoor air in Hangzhou were determined. The mean concentration of the total carbonyl compounds in summer was 222.6 μg/m³, higher than that in winter (68.5 μg/m³). The concentration of a specific carbonyl in indoor air was higher than the outdoor air measurement, indicating the release of carbonyls from the indoor sources. Formaldehyde and acetone were the most abundant carbonyls detected in summer and winter, respectively. Multiple regression analysis indicated that carbonyl concentrations in residential indoor air depended on the age of decoration and furniture, as well as their concentrations in outdoor air. In addition, a primary estimation showed that the health risks of carbonyls in summer were higher than those in winter.     

Satellite monitoring for carbon monoxide and particulate matter during forest fire episodes in Northern Thailand

This study explored the use of satellite data to monitor carbon monoxide (CO) and particulate matter (PM) in Northern Thailand during the dry season when forest fires are known to be an important cause of air pollution. Satellite data, including Measurement of Pollution in the Troposphere (MOPITT) CO, Moderate Resolution Imaging Spectroradiometer aerosol optical depth (MODIS AOD), and MODIS fire hotspots, were analyzed with air pollution data measured at nine automatic air quality monitoring stations in the study area for February–April months of 2008–2010. The correlation analysis showed that daily CO and PM with size below 10 μm (PM₁₀) were associated with the forest fire hotspot counts, especially in the rural areas with the maximum correlation coefficient (R) of 0.59 for CO and 0.65 for PM₁₀. The correlations between MODIS AOD and PM₁₀, between MOPITT CO and CO, and between MODIS AOD and MOPITT CO were also analyzed, confirming the association between these variables. Two forest fire episodes were selected, and the dispersion of pollution plumes was studied using the MOPITT CO total column and MODIS AOD data, together with the surface wind vectors. The results showed consistency between the plume dispersion, locations of dense hotspots, ground monitoring data, and prevalent winds. The satellite data were shown to be useful in monitoring the regional transport of forest fire plumes.     

采样罐和气袋保存116种挥发性有机物效果研究

为了提高挥发性有机物(VOCs)分析的准确性,笔者考察了3种采样罐和2种气袋对116种VOCs的保存效果。结果表明:VOCs在不同种类采样罐和气袋中的保存情况有一定差异,整体上Silonite采样罐的保存效果相对更稳定,罐内水分含量会对部分VOCs的保存效果造成影响(特别是对含氧有机物);保存实际样品时,能保证VOCs分析准确性的时间为12 d。     

Carbon monoxide concentrations in outdoor wood-fired kitchens in Ouagadougou,Burkina Faso—implications for women’s and children’s health

A majority of households in developing countries rely on biomass fuel for cooking, typically burned in open fires or simple stoves. The incomplete combustion of these fuels causes adverse health effects such as respiratory diseases, especially among women and children. However, quantitative data on pollution levels and on associated diseases are limited. We examined cooking habits and self-reported health in 31 households with outdoor open wood fires in Ouagadougou, Burkina Faso, using structured interviews. In eight households, carbon monoxide (CO) was measured using passive sampling. In addition, meteorology and ambient CO concentrations were assessed. The average CO concentration during cooking was 4.3 ppm, with a maximum of 65.3 ppm and minimum of 0.3 ppm (1-min values). A clear daily pattern was observed, with relatively low concentrations during the day and high during the evening, occasionally exceeding the World Health Organization 1- and 8-h guidelines when the air stabilised. On average, CO concentrations were 43 % higher in kitchens located in closed yards than in those located in open yards, showing that fireplace location affected the levels. Eye irritation and coughing among women and children were reported by 30 % of the households. Based on previously reported relations between CO concentrations and fine particles (<2.5 μm), the exposure to biomass smoke appears to be high enough to pose a considerable health risk among women and children in households with outdoor open wood fires. The results suggest that burning should be limited between sunset and dawn and in areas with limited ventilation to reduce pollutions levels.     

工业温室气体CO2排放监测技术前期研究

介绍了国内外二氧化碳（ CO2）气体检测方法，选取红外传感器、非分散红外和气相色谱3种方法监测工业燃煤废气中的CO2。试验结果表明，3种方法的精密度和准确度均满足要求；单一燃煤废气中CO2的体积分数范围为6．70％～15．10％，同一排气筒中CO2体积分数5 min的波动范围为0～22．4％；同一排气筒（单一燃煤废气）中CO2和O2的体积分数有一定的关联性，二者之和基本稳定在19％～21％范围；非分散红外法和气相色谱法测定同一样品的相对偏差为0．9％～3．4％；红外传感器适用于有组织排放的现场监测，另2种方法适用于无组织废气和环境空气监测。     

Characterisation of particulate matter on the receptor level in a city environment

Airborne particulate matter (PM) has become one of the dominant pollutants with the increasing material and energy demand due to global economic growth. The main objective of this research is to provide a comprehensive receptor level characterisation of the particulate matter collected in a city environment. Particulate matter samples were collected on Tapered Element Oscillating Microbalance (TEOM) filters from five monitoring sites over a period of 1 year. An Andersen eight-stage cascade impactor was also used to collect airborne PM samples from three other locations to compare with the samples collected by TEOM. All the samples were then subjected to individual particle morphology and chemical composition analysis by SEM/EDS. Bulk chemical composition of the samples were also analysed through ICP–OES. Based on these analyses, possible sources of the PM samples were identified. The results showed that the monitoring sites in residential environments were dominated by transportation-derived particles and other migratory particulates. Monitoring sites near the city centre were dominant by particles from transportation, with biological particles abundant for the site closer to a river. The monitoring station located close to the industrial area, despite only 200 m away from a motorway, has low contribution of non-exhaust particulates from vehicles. Instead, the particulates collected from this site were dominated by industrial sources. An air dispersion modelling package was also used to model the particulate matter dispersion in the city area for the period of sampling. The results from the model showed that the points of high emissions were around industrial areas.     

Changes in wind erosion over a 25-year restoration chronosequence on the south edge of the Tengger Desert,China: implications for preventing desertification

Wind erosion is a primary cause of desertification as well as being a serious ecological problem in arid and semi-arid areas across the world. To determine mechanisms for restoring desertified lands, an unrestored shifting sand dune and three formerly shifting sand dunes (desertified lands) that had been enclosed and afforested for 5, 15, and 25 years were selected for evaluation on the south edge of the Tengger Desert, China. Based on sampling heights between 0.2 and 3 m, the critical threshold average wind speed was 6.5 m s^?1 at 2 m where the sand transport rate was reduced from 285.9 kg m^?2 h^?1 on the unrestored dunes to 9.1 and 1.8 kg m^?2 h^?1 on the sites afforested and enclosed for 5 and 15 years, respectively. The percentage of wind eroded area was reduced from 99.9% on the unrestored dune to 94.5, 9.0, and 0.5% on the sites afforested and enclosed for 5, 15, and 25 years, respectively. Wind erosion was effectively reduced after 15 years. Although there were different driving factors for wind erosion mitigation on the different restoration stages, an increase in the vegetation cover, surface roughness, soil shear strength, soil clay content, organic matter, and reduction in the near-surface wind speed were the primary variables associated with the restoration chronosequence. We conclude that reducing the wind speed and developing a biological crust through vegetation restoration were the critical components for restoration of desertified land.     

基于多源大数据可视化的城市居民区绿地土壤环境监测点位布设及采样研究

为科学合理的监测城市居民区绿地土壤环境状况,对居民区绿地土壤监测点位布设和采样的方法进行研究,包括代表性居民区的选取、监测点采样位置的确定、点位数量的确定等。通过多源大数据可视化手段选取某城市代表性的居民区,对其居民区内绿地土壤重金属(镉、汞、砷、铅、铜、铬、锌和镍)进行监测。结果表明:多源大数据的应用对城市土壤监测布点具有积极作用和优势;不同建筑年代的居民区土壤中重金属含量存在一定差异,为全面监测居民区土壤环境状况应选取不同建筑年代的居民区作为监测对象;不同采样位置对居民区土壤样品中重金属含量无明显影响,优先于居民区内面积占比较大的绿地采样;同一居民区内不同监测点位样品存在差异性,每个居民区内至少布设3~4个监测点位可代表该居民区土壤环境状况。     

Radioactive Contamination Control by Atmospheric Dispersion Assessment of Airborne Indicator Contaminants: Numerical Model Validation

In this work, a numerical model is proposed to estimate air concentration of released airborne radioactive contaminants ¹³¹I and ¹³⁷Cs. A Gaussian dispersion model is used to assess the atmospheric dispersion of radioactive contaminants released continuously from a nuclear power plant as a result of an accident. The model uses various input parameters such as source height, release rate, stability class, wind speed, and wind direction. The validation of the model was carried out by comparing its predicted values with published experimental data. The model was extensively tested by simulating several accidental situations. The main conclusion drawn from these tests is that for large downwind distances from the release point, the contaminant concentrations predicted by the model diverge drastically from measured data, while for short distances, the predicted values generally agree quite well with experimental data. The obtained activity concentrations range from 1.57?×?10² to 6.43?×?10³ Bq/m³ for ¹³¹I and from 3.18?×?10^?2 to 9.72?×?10² Bq/m³ for ¹³⁷Cs. The estimated standard deviation coefficients values range of 7.2 to 6847.7 m, and the maximum absolute error predicted by the model for these parameters was less than 5%.     

Removal Efficiency of PM10 via Ventilation with Residential Exhaust Hood and Conditions for Reducing Human Intake Fraction

Environmental Modeling & Assessment - As the number of enclosed residential buildings increases to minimize energy consumption, research on indoor air quality is becoming more important....     

Fluoride pollution of atmospheric precipitation and its relationship with air circulation and weather patterns (Wielkopolski National Park, Poland)

A 2-year study (2010–2011) of fluorides in atmospheric precipitation in the open area and in throughfall in Wielkopolski National Park (west-central Poland) showed their high concentrations, reaching a maximum value of 2 mg/l under the tree crowns. These high values indicate substantial deposition of up to 52 mg/m²/year. In 2011, over 51 % of open area precipitation was characterized by fluoride concentration higher than 0.10 mg/l, and in throughfall such concentrations were found in more than 86 % of events. In 2010, a strong connection was evident between fluoride and acid-forming ions, and in 2011, a correlation between phosphate and nitrite ions was seen. Analysis of available data on F^? concentrations in the air did not show an unequivocal effect on F^? concentrations in precipitation. To find reasons for and source areas of high fluoride pollution, the cases of extreme fluoride concentration in rainwater were related to atmospheric circulation and weather patterns. Weather conditions on days of extreme pollution were determined by movement of weather fronts over western Poland, or by small cyclonic centers with meteorological fronts. Macroscale air advection over the sampling site originated in the western quadrant (NW, W, and SW), particularly in the middle layers of the troposphere (2,500–5,000 m a.s.l.). Such directions indicate western Poland and Germany as possible sources of the pollution. At the same time in the lower troposphere, air inflow was frequently from the north, showing short distance transport from local emitters, and from the agglomeration of Poznań.     

A positive chemical ionization GC/MS method for the determination of airborne ethylene glycol and propylene glycols in non-occupational environments

An analytical method for ethylene glycol and propylene glycols has been developed for measuring airborne levels of these chemicals in non-occupational environments such as residences and office buildings. The analytes were collected on charcoal tubes, solvent extracted, and analyzed by gas chromatography-mass spectrometry using a positive chemical ionization technique. The method had a method detection limit of 0.07 microg m(-3) for ethylene glycol and 0.03 microg m(-3) for 1,2- and 1,3-propylene glycols, respectively, based on a 1.44 m3 sampling volume. Indoor air samples of several residential homes and other indoor environments have been analyzed. The median concentrations of ethylene glycol and 1,2-propylene glycol in nine residential indoor air samples were 53 microg m(-3) and 13 microg m(-3) respectively with maximum values of 223 microg m(-3) and 25 microg m(-3) detected for ethylene glycol and 1,2-propylene glycol respectively. The concentrations of these two chemicals in one office and two laboratories were at low microg m(-3) levels. The maximum concentration of 1,3-propylene glycol detected in indoor air was 0.1 microg m(-3).     

Mineralogy of Atmospheric Suspended Dust in Three Indoor And One Outdoor Location in Oman

The aim of this work is to characterize the mineral phases present in the atmosphere at three locations in northern Oman. Samples of atmospheric particles were collected using a high volume sampler. Three indoor and one outdoor location were chosen in this investigation. Sampling locations included a residential house located nearby the cement plant, a residential house located nearby a refinery plant, and a residential house located at Al-Suwayq residential area. Indoor air was sampled from these three houses. Moreover, for the Al-Suwayq residential house, sampling was also taken outside the house for comparison. The dust samples were analysed for their microanalysis characterization and their mineral contents as well. The microanalysis enabled us to identify the metals present in the particles. Furthermore, the mineralogical analysis of the sample filters showed the presence of quartz as the principal phase inside the house of Al-Suwayq, whereas quartz, dolomite, and gypsum were common phases outside the house. In the residential house nearby the cement plant, it was found that calcite, quartz, dolomite and goethite were the principal phases whereas the particles collected from the house nearby the refinery composed primarily of dolomite and calcite. The airborne dust collected at the refinery and Al-Suwayq were probably sourced in the natural environment and mobilised by natural processes. However, at the cement factory the crushing and grinding of limestone during the industrial process has contributed significantly to the airborne dust load. Generally, the information obtained in this study will be invaluable as no data for the mineral content of atmospheric dust existed in the Oman.     

Spatiotemporal distribution of airborne elements monitored with the moss bags technique in the Greater Thriasion Plain, Attica, Greece

The well-known moss bags technique was applied in the heavily polluted Thriasion Plain region, Attica, Greece, in order to study the spatiotemporal distribution, in the atmosphere, of the following 32 elements: Na, Al, Cl, Ca, Sc, Ti, V, Cr, Mn, Fe, Ni, Co, Zn, As, Se, Br, Sr, Mo, Sb, I, Ba, La, Ce, Sm, Tb, Dy, Yb, Hf, Ta, Hg, Th, and U. The moss bags were constituted of Sphagnum girgensohnii materials. The bags were exposed to ambient air in a network of 12 monitoring stations scattered throughout the monitoring area. In order to explore the temporal variation of the pollutants, four sets of moss bags were exposed for 3, 6, 9, and 12 months. Instrumental neutral activation analysis was used for the determinations of the elements. The data were analyzed using the Pearson correlations, the partial redundancy analysis, and the biplot statistical methods. Some pairs of elements were highly correlated indicating a probable common source of origin. The levels of the measured pollutants were unevenly distributed throughout the area and different pollutants exhibited different spatial patterns. In general, higher loads were observed in the stations close to and within the industrial zone. Most of the measured elements (e.g., Al, Ca, Ni, I, Zn, Cr, and As) exhibited a monotonic accumulation trend over time. Some elements exhibited different dynamics. The elements Mn, Mo, and Hg showed a decreasing trend, probably due to leaching and/or volatilization processes over time. Na and Br initially showed an increasing trend during the winter and early spring periods but decreased drastically during the late warm period. The results further suggest that the moss bags technique would be considered valuable for the majority of elements but should be used with caution in the cases of elements vulnerable to leaching and/or volatilization. It also suggests that the timing and the duration of the exposure of moss materials should be considered in the interpretation of the results.