高效液相色谱法测定废水中阿维菌素的含量

建立了一种采用高效液相色谱法(HPLC)检测废水中阿维菌素含量的方法。以二氯甲烷作萃取剂萃取废水中的阿维菌素,以甲醇 H2O(88 12)为流动相、Spherisorb C18柱高效液相色谱分离、紫外检测器在波长为245nm时测定。阿维菌素标准曲线的线性回归系数r=0.9948,线性范围为0.025~0.100mg/ml;水样相对标准偏差小于10.6%,加标回收率为75.8%~87.6%。     

固相萃取-高效液相色谱法测定废水中的酚类化合物

建立了Supelclean ENVI-Chrom P柱固相萃取-高效液相色谱法测定废水中11种酚类化合物的分析方法,并对固相萃取条件和液相色谱条件进行了讨论。该方法分离效果良好,净化效果明显,方法检出限为2×10-3~2×10-2mg/L,平行分析(n=6)的RSD为2.7%~16.4%,废水加标回收率除2,4-二硝基酚偏低以外,其他化合物的回收率为61.4%~115.8%。     

分光光度法测定废水中草甘膦的探讨

探讨了亚硝基衍生化紫外分光光度法测定废水中草甘膦的适用性,考察了硫酸加入体积对亚硝化反应的影响,提出应根据样品碱度调整硫酸用量。方法与高效液相色谱法测定值的重现性较好,应用于实际废水中草甘膦测定的加标回收率为95%～105%,平行测定的RSD≤1.3%,检出限为0.069 mg/L,检测上限为50.0 mg/L,废水中可能存在的伯胺和叔胺类物质对测定无明显干扰。     

电感耦合等离子体原子发射光谱法测定废水中的铊

采用电感耦合等离子体原子发射光谱仪(ICP-AES)测定废水中铊,并对测定波长、介质及其酸度、共存元素干扰等因素进行分析和条件优化,使该方法在0 mg/L~5.00 mg/L范围内线性良好,相关系数为0.999 9。方法检出限为22μg/L,该方法对铊标准样品测定的结果在保证值范围内,4份废水样7次测定结果的RSD为0.2%~0.8%,实际废水样品的加标回收率为98.0%~100%。     

热分解齐化原子吸收光度法测定废水中的总汞

建立用热分解齐化原子吸收光度法测定废水中总汞的方法。将样品加热至650℃,使所有汞转化成蒸气,利用催化管将蒸气中的二价汞转化成零价汞,再利用金管捕集零价汞,加热金管释放零价汞并使其进入分析单元,在253.7 nm处以冷原子光谱法测定汞含量。方法检出限(t S)为0.045μg/L,测定下限为0.180μg/L。相对标准偏差RSD为2.3%~4.6%,加标回收率P为86.2%~94.8%。用热分解齐化原子吸收光度法直接测定废水中总汞,操作简单,污染小,毒性低,可替代《水质总汞的测定冷原子吸收分光光度法》(HJ 597-2011)。     

毛细管柱气相色谱法测定空气中二硫化碳

利用毛细管柱对二硫化碳进行分离,火焰光度检测器(FPD)进行检测,建立了空气中二硫化碳的毛细管柱气相色谱测定法。该方法检出限为0.03 mg/m~3,空白样品加标回收率为91.3%~102.8%,精密度(RSD,n=7)为1.04%~3.91%,变异系数为1.00%~3.93%。实验结果表明,该方法准确可靠、灵敏度好、分析速度快、操作简便,适用于空气中二硫化碳的测定。     

离子色谱法测定化工废水中有机醇胺类化合物

采用固相萃取-离子色谱法同时测定化工废水中乙醇胺、二乙醇胺、三乙醇胺、N-甲基二乙醇胺和N-丁基二乙醇胺等5种有机醇胺类化合物。通过试验,对固相萃取、离子色谱条件进行优化,优选C_(18)为固相萃取填料,使方法在1.10 mg/L～26.0 mg/L范围内线性良好,方法的检出限为0.72 mg/L～1.02 mg/L。废水样品3个质量浓度水平的加标回收率为84.0%～101%,测定6次结果的RSD为1.7%～12.0%。将该方法用于医药化工企业废水的测定,结果部分醇胺类化合物检出。     

二氯甲烷萃取与气相色谱—质谱结合新方法测定饮用水源地水中的苦味酸

为建立饮用水源地中苦味酸分析测定的新方法,将10 ml水样中的苦味酸氯化后,以二氯甲烷萃取,用气相色谱—质谱法(GC—MSD)测定水中苦味酸的含量,采用保留时间定性,外标法定量。结果表明,最佳萃取时间为4 min,最佳萃取剂用量为1.5 ml,该法能快速而有效的提取并测定水中苦味酸,检出限低(0.4μg/L)、精密度(RSD=1.8%)和准确度高(加标回收率93.16%)、标准曲线线性(r=0.999)较好,能满足饮用水源地水中苦味酸的测定要求。     

ICP-AES法和分光光度法测定工业废水中总磷的方法比较

用ICP-AES法和分光光度法同时测定4种不同工业废水中的总磷含量,将2种方法的测定结果作比对。试验表明,ICP-AES法对国家标准样品的测定结果具有较高的准确度和精密度,4种废水样品测定结果的加标回收率为94.0%~110%,RSD在0.9%~3.2%之间。分光光度法适用于低浓度、低干扰样品的测定,对于高浓度含磷废水,取样体积和样品稀释倍数均会对其测定结果产生显著影响。消解样品经浊度-色度补偿后,分光光度法的测定结果精密度较低。     

连续流动分析法测定地表水中总氮

采用50 mm流动检测池,建立了连续流动分析法测定地表水中总氮。方法检出限为0.02 mg/L,水样加标回收率为100%~101%,平行样品相对偏差为0.10%~0.27%,精密度(RSD,n=6)为0.72%~1.10%。实验结果表明,该方法准确可靠、灵敏度高、重现性好、分析速度快、操作简便,适用于地表水中总氮的分析。     

在线蒸馏-无人值守连续流动分析法测定污水中氨氮

采用在线蒸馏-无人值守连续流动分析法对污水中氨氮进行检测,方法在0.00~10.0 mg/L范围内线性良好,检出限为0.014 mg/L,实际样品测定的相对标准偏差为1.24%~4.15%,加标回收率为93.0%~108%,精密度和准确度均能满足污水中氨氮的测定要求。     

高效液相色谱法测定地表水中四乙基铅

系统研究了地表水中四乙基铅的液相色谱分析方法,水中四乙基铅经二氯甲烷萃取浓缩后,用高压液相色谱柱分离,在280 nm波长处检测,根据保留时间定性,外标法定量,检出限及测定下限分别为0.02μg/L和0.06μg/L,低于地表水限值0.1μg/L,地表水平行测定的相对标准偏差均小于5%,地表水和废水样品加标回收率分别为79.4%～82.0%和62.5%～106.6%。     

变色酸比色法测定甲胺生产废水中甲醇

建立了变色酸比色测定甲胺生产废水中甲醇的方法，确定了最大吸收波长，优化了试验条件。方法在0mg／L-7．00mg／L范围内线性良好，检出限为0．07mg／L，标准溶液测定的RSD≤0．9％，废水样品的加标回收率为98．8％-101％。     

液相色谱-串联质谱法同时测定污水中10种精神活性物质

建立了采用液相色谱-串联质谱法(LC-MS/MS)同时测定污水中10种精神活性物质的分析方法。污水样品经甲酸与甲酸铵调节pH后,加入氘代内标混匀,离心并过滤膜后可直接上样分析。研究表明,在1~250 ng/L的线性范围内,10种精神活性物质的线性相关系数均大于0.992,定量限均低于0.5 ng/L。在3个加标水平下,10种精神活性物质的加标回收率为87.2%~114%,相对标准偏差为0.53%~3.60%(n=3)。将该方法应用于某区域10份生活污水样品的检测,在3份水样中检出吗啡、甲基苯丙胺、氯胺酮等精神活性物质,对应的质量浓度范围分别为3.41~9.55、0.90~1.63、1.06~1.78 ng/L。与经固相萃取前处理后的分析方法相比,该方法可在10 min内完成分离和检测的全过程,具有简单、快速、节约的优点,可用于污水样品中10种痕量水平精神活性物质的定量分析。     

On-line solid phase extraction and liquid chromatography/tandem mass spectrometry to quantify pharmaceuticals, pesticides and some metabolites in wastewaters, drinking, and surface waters

A simple on-line method was developed for the analysis of pharmaceuticals, pesticides and some metabolites in drinking, surface and wastewater samples. The technique is based on the use of on-line solid-phase extraction combined with liquid chromatography electrospray tandem mass spectrometry with positive electrospray ionization (LC-ESI(PI)-MS/MS). The injection of only 1 mL of filtered water sample is used with a total analysis time of 20 min, including the period required to flush the SPE cartridge with organic solvent and reconditioning the LC column. Method detection limits were in the range of 2 to 24 ng L(-1) for the compounds of interest, with recoveries from 87 to 110% in surface as well as wastewater samples. Matrix effects were observed for some compounds without exceeding more than 25%. All results displayed a good degree of reproducibility, with relative standard deviations (RSD) of less than 12% for all compounds. Moreover, at least 200 samples were analyzed without altering the performance of the pre-concentration column. This method was preferred over traditional off-line procedures because it minimizes tedious sample preparation, increases productivity and sample throughput. The analysis of various water and wastewater samples showed that caffeine, carbamazepine and atrazine could be detected in all the samples analysed and the selected compounds are always present in at least one of the sample types.     

Effect of process conditions on the analysis of free and conjugated estrogen hormones by solid-phase extraction–gas chromatography/mass spectrometry (SPE–GC/MS)

Simultaneous analysis of 11 free estrogen hormones and five conjugated estrogens in water and municipal wastewater was studied. The analytical method was developed and tested for different types of solid-phase extraction adsorbents, eluents, sample containers and storage conditions, derivatization, and matrix effects. Varian Bond Elut C-18 solid-phase extraction adsorbent cartridge was selected based on its high recoveries for both free and conjugated estrogens. Sample storage conditions, as well as selection and pretreatment of sample container materials, can affect the trace level analysis of estrogens. Silanization of glassware is observed to provide low relative standard deviation (RSD) in the analysis and less percentage loss due to contacting with sample container materials. Light exposure during the test can significantly impact the results. The derivatized samples stored at −20°C for at least 6 days showed less than 10.5% average RSD in the analysis. The recovery efficiency in clean water varies from 72% to 101% for free estrogens and 78% to 82% for conjugated estrogens. The method detection limits (MDL) for most of the compounds range from 30 to 870 ng/L using a sample volume of 200 mL. With a sample volume of 3 L, the most sensitive compound produces a MDL of 0.03 ng/L. Dilute methanol is used to wash the loaded cartridge as a cleanup step in order to remove interfering species during analysis of wastewater samples. Using the optimized analytical methods, the concentration level of free estrogens in the influent and effluent municipal wastewaters is tested.     

工业废水中痕量汞的直接测定

采用DMA-80型直接测汞仪测定工业废水中的痕量汞,优化了干燥时间、分解温度、释放温度等试验条件。方法在0μg/L~600μg/L范围内线性良好,检出限为5.0×10-5mg/L,工业废水样品平行测定的RSD≤0.2%,加标回收率为96.7%~105%。     

液液萃取-高效液相色谱法测定水中四乙基铅

采用高效液相色谱紫外检测器测定水中四乙基铅,用二氯甲烷液液萃取,以甲醇/水混合溶液(体积比为95:5)为流动相,Z0RBAX Eclipse XDB-C18色谱柱分离,选择测定波长为280 nm.方法在0.100mg/L～1.00mg/L范围内线性良好,检出限和测定下限分别为0.01μg/L和0.04μg/L,水样平行...